OLD-CISCO-SYS-MIB device MIB details by Cisco
OLD-CISCO-SYS-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing OLD-CISCO-SYS-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | OLD-CISCO-SYS-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ***************************************************************** -- OLD-CISCO-SYS-MIB.my: Cisco System MIB file -- -- July 1994, Jeffrey T. Johnson -- -- Copyright (c) 1994-1996 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** -- -- Prior to 10.2, Cisco's lsystem mib group contained a curious -- assortment of mib objects. For 10.2, in order to allow similar -- objects to be compiled separately with the mib compiler, the -- lsystem group was separated into an envmon group (lenv), a cpu -- group (lcpu), a memory group (lmem), and a system group (lsystem). -- In order to preserve the OBJECT IDENTIFIERS from release 10.1 to -- 10.2, however, all four groups are still based at { local 1 }. -- This is fine from the mib compiler point-of-view, but causes -- problems for some test tools which don't like the fact that -- lsystem, lenv, lmem, and lcpu all have the same OBJECT IDENTIFIER. -- In order to work around this problem, this file exists which -- is a combination of the four 10.2 "system" mibs, with everything -- falling under the lsystem group (as it did in 10.1). -- -- This mib should only be used as a replacement for the four separate -- system mibs (OLD-CISCO-CPU.my, OLD-CISCO-ENVMON-MIB.my, -- OLD-CISCO-MEMORY-MIB.my, OLD-CISCO-SYSTEM-MIB.my) in test tool -- environments. The aforementioned mibs should always be used in -- code generation OLD-CISCO-SYS-MIB DEFINITIONS ::= BEGIN IMPORTS IpAddress FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB local FROM CISCO-SMI; lsystem OBJECT IDENTIFIER ::= { local 1 } -- Local Variable Section -- This section describes the local variables within the cisco -- product line. Groups may or may not be present depending -- on the software options present in the managed device. -- Local System Group -- This group is present in all products. romId OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable contains a printable octet string which contains the System Bootstrap description and version identification." ::= { lsystem 1 } whyReload OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable contains a printable octet string which contains the reason why the system was last restarted." ::= { lsystem 2 } hostName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable represents the name of the host in printable ascii characters." ::= { lsystem 3 } domainName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This variable is the domain portion of the domain name of the host." ::= { lsystem 4 } authAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "This variable contains the last SNMP authorization failure IP address." ::= { lsystem 5 } bootHost OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Contains the IP address of the host that supplied the currently running software." ::= { lsystem 6 } ping OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS obsolete DESCRIPTION "The ping mib object is obsolete as of IOS 10.2 It has been superseded by the Cisco Ping MIB" ::= { lsystem 7 } freeMem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS obsolete DESCRIPTION "The freeMem mib object is obsolete as of IOS 11.1 It has been replaced with the cisco memory pool mib" ::= { lsystem 8 } bufferElFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free buffer elements." ::= { lsystem 9 } bufferElMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of buffer elements." ::= { lsystem 10 } bufferElHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of buffer element hits." ::= { lsystem 11 } bufferElMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of buffer element misses." ::= { lsystem 12 } bufferElCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of buffer element creates." ::= { lsystem 13 } bufferSmSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the size of small buffers." ::= { lsystem 14 } bufferSmTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the total number of small buffers." ::= { lsystem 15 } bufferSmFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free small buffers." ::= { lsystem 16 } bufferSmMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of small buffers." ::= { lsystem 17 } bufferSmHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of small buffer hits." ::= { lsystem 18 } bufferSmMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of small buffer misses." ::= { lsystem 19 } bufferSmTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of small buffer trims." ::= { lsystem 20 } bufferSmCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of small buffer creates." ::= { lsystem 21 } bufferMdSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the size of medium buffers." ::= { lsystem 22 } bufferMdTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the total number of medium buffers." ::= { lsystem 23 } bufferMdFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free medium buffers." ::= { lsystem 24 } bufferMdMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of medium buffers." ::= { lsystem 25 } bufferMdHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of medium buffer hits." ::= { lsystem 26 } bufferMdMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of medium buffer misses." ::= { lsystem 27 } bufferMdTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of medium buffer trims." ::= { lsystem 28 } bufferMdCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of medium buffer creates." ::= { lsystem 29 } bufferBgSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the size of big buffers." ::= { lsystem 30 } bufferBgTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the total number of big buffers." ::= { lsystem 31 } bufferBgFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free big buffers." ::= { lsystem 32 } bufferBgMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of big buffers." ::= { lsystem 33 } bufferBgHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of big buffer hits." ::= { lsystem 34 } bufferBgMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of big buffer misses." ::= { lsystem 35 } bufferBgTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of big buffer trims." ::= { lsystem 36 } bufferBgCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of big buffer creates." ::= { lsystem 37 } bufferLgSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the size of large buffers." ::= { lsystem 38 } bufferLgTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the total number of large buffers." ::= { lsystem 39 } bufferLgFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free large buffers." ::= { lsystem 40 } bufferLgMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of large buffers." ::= { lsystem 41 } bufferLgHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of large buffer hits." ::= { lsystem 42 } bufferLgMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of large buffer misses." ::= { lsystem 43 } bufferLgTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of large buffer trims." ::= { lsystem 44 } bufferLgCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of large buffer creates." ::= { lsystem 45 } bufferFail OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Count of the number of buffer allocation failures." ::= { lsystem 46 } bufferNoMem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Count of the number of buffer create failures due to no free memory." ::= { lsystem 47 } netConfigAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Holds the address of the host that supplied the network-confg file." ::= { lsystem 48 } netConfigName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Holds the name of the network configuration file." ::= { lsystem 49 } netConfigSet OBJECT-TYPE SYNTAX DisplayString ACCESS write-only STATUS mandatory DESCRIPTION "Cause the loading of a new network-confg file using TFTP." ::= { lsystem 50 } hostConfigAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS obsolete DESCRIPTION "Contains the address of the host that provided the host-config file." ::= { lsystem 51 } hostConfigName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS obsolete DESCRIPTION "Contains the name of the last configured host-confg file." ::= { lsystem 52 } hostConfigSet OBJECT-TYPE SYNTAX DisplayString ACCESS write-only STATUS obsolete DESCRIPTION "Cause the loading of a new host-confg file using TFTP." ::= { lsystem 53 } writeMem OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Write configuration into non-volatile memory / erase config memory if 0." ::= { lsystem 54 } writeNet OBJECT-TYPE SYNTAX DisplayString ACCESS write-only STATUS mandatory DESCRIPTION "Write configuration to host using TFTP." ::= { lsystem 55 } busyPer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU busy percentage in the last 5 second period. Not the last 5 realtime seconds but the last 5 second period in the scheduler." ::= { lsystem 56 } avgBusy1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "1 minute exponentially-decayed moving average of the CPU busy percentage." ::= { lsystem 57 } avgBusy5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "5 minute exponentially-decayed moving average of the CPU busy percentage." ::= { lsystem 58 } idleCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "cisco internal variable. not to be used" ::= { lsystem 59 } idleWired OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "cisco internal variable. not to be used" ::= { lsystem 60 } ciscoContactInfo OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "cisco's name and address" ::= { lsystem 61 } bufferHgSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the size of huge buffers." ::= { lsystem 62 } bufferHgTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the total number of huge buffers." ::= { lsystem 63 } bufferHgFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of free huge buffers." ::= { lsystem 64 } bufferHgMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the maximum number of huge buffers." ::= { lsystem 65 } bufferHgHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of huge buffer hits." ::= { lsystem 66 } bufferHgMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of huge buffer misses." ::= { lsystem 67 } bufferHgTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of huge buffer trims." ::= { lsystem 68 } bufferHgCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Contains the number of huge buffer creates." ::= { lsystem 69 } netConfigProto OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Holds the protocol that supplied the network-confg file." ::= { lsystem 70 } hostConfigProto OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Holds the protocol that supplied the host- confg file." ::= { lsystem 71 } sysConfigAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Holds the address of the host that supplied the system boot image." ::= { lsystem 72 } sysConfigName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Holds the name of the system boot image." ::= { lsystem 73 } sysConfigProto OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Holds the protocol that supplied the system boot image." ::= { lsystem 74 } sysClearARP OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Perform a clearing of the entire ARP cache and invalidation of route caches." ::= { lsystem 75 } sysClearInt OBJECT-TYPE SYNTAX INTEGER ACCESS write-only STATUS mandatory DESCRIPTION "Clear interface given IfIndex as value." ::= { lsystem 76 } envPresent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Is there an environmental monitor card in this box?, 0 - No, 1-AGS card present, wrong firmware, 2-AGS CARD present, firmware ok, 3-7000 support" ::= { lsystem 77 } envTestPt1Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 1. Typically ambient air or the temperature of air entering the router" ::= { lsystem 78 } envTestPt1Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 1. Typically a temperature in centigrade." ::= { lsystem 79 } envTestPt2Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 2. Typically airflow or the temperature of air leaving the router" ::= { lsystem 80 } envTestPt2Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 2. Typically a temperature in centigrade." ::= { lsystem 81 } envTestPt3Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 3. Typically +5 volt" ::= { lsystem 82 } envTestPt3Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 3. Typically the value in millivolts of the +5v supply" ::= { lsystem 83 } envTestPt4Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 4. Typically +12 volt" ::= { lsystem 84 } envTestPt4Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 4. Typically the value in millivolts of the +12v supply" ::= { lsystem 85 } envTestPt5Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 5. Typically -12 volt" ::= { lsystem 86 } envTestPt5Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 5. Typically the value in millivolts of the -12v supply" ::= { lsystem 87 } envTestPt6Descr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of the test point 6. Typically -5 volt" ::= { lsystem 88 } envTestPt6Measure OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current value of test point 6. Typically the value in millivolts of the -5v supply" ::= { lsystem 89 } envTestPt1MarginVal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value at which the router will shutdown. Typically the ambient air temperature that will shut the router down. (e.g. 43)" ::= { lsystem 90 } envTestPt2MarginVal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value at which the router will shutdown. Typically the airflow air temperature that will shut the router down. (e.g. 58)" ::= { lsystem 91 } envTestPt3MarginPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "+/- Percentage that will shut the router down, (e.g. 10%) typically +5 volt" ::= { lsystem 92 } envTestPt4MarginPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "+/- Percentage that will shut the router down, (e.g. 15%) typically +12 volt" ::= { lsystem 93 } envTestPt5MarginPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "+/- Percentage that will shut the router down, (e.g. 15%) typically -12 volt" ::= { lsystem 94 } envTestPt6MarginPercent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "+/- Percentage that will shut the router down, (e.g. 10%) typically -5 volt" ::= { lsystem 95 } envTestPt1last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt1 when last shutdown occurred." ::= { lsystem 96 } envTestPt2last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt2 when last shutdown occurred." ::= { lsystem 97 } envTestPt3last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt3 when last shutdown occurred." ::= { lsystem 98 } envTestPt4last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt4 when last shutdown occurred." ::= { lsystem 99 } envTestPt5last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt5 when last shutdown occurred." ::= { lsystem 100 } envTestPt6last OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of TestPt6 when last shutdown occurred." ::= { lsystem 101 } envTestPt1warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 102 } envTestPt2warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 103 } envTestPt3warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 104 } envTestPt4warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 105 } envTestPt5warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 106 } envTestPt6warn OBJECT-TYPE SYNTAX INTEGER { warning(1), noWarning(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Is this test point at a warning level?" ::= { lsystem 107 } envFirmVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of Environmental Card firmware" ::= { lsystem 108 } envTechnicianID OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Technician ID" ::= { lsystem 109 } envType OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The type of environmental card" ::= { lsystem 110 } envBurnDate OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The calibration / burn in date" ::= { lsystem 111 } envSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Serial Number of environmental monitor card" ::= { lsystem 112 } END