| a3ipxPCPort |
.1.3.6.1.4.1.43.2.11.1.1.1 |
|
The port to which this Policy Control entry applies.
|
| a3ipxPCRteAdvCtl |
.1.3.6.1.4.1.43.2.11.1.1.2 |
|
The object enables or disables the use of the
'advertisable' entries in the Route Policy Table.
|
| a3ipxPCRteAdvType |
.1.3.6.1.4.1.43.2.11.1.1.3 |
|
The object specifies whether only those routes listed
as 'advertisable' in the Route Policy Table are
advertised from this port (normal), or if only those
routes that are not listed as 'advertisable' in the
Route Policy Table are advertised (inverse).
|
| a3ipxPCRteRcvCtl |
.1.3.6.1.4.1.43.2.11.1.1.4 |
|
The object enables or disables the use of the
'receivable' entries in the Route Policy Table.
|
| a3ipxPCRteRcvType |
.1.3.6.1.4.1.43.2.11.1.1.5 |
|
The object specifies whether only those routes listed
as 'receivable' in the Route Policy Table are accepted
from this port (normal), or if only those routes that
are not listed as 'receivable' in the Route Policy Table
are accepted (inverse).
|
| a3ipxPCSvcAdvCtl |
.1.3.6.1.4.1.43.2.11.1.1.6 |
|
The object enables or disables the use of the
'advertisable' entries in the Service Policy Table.
|
| a3ipxPCSvcAdvType |
.1.3.6.1.4.1.43.2.11.1.1.7 |
|
The object specifies whether only those routes listed
as 'advertisable' in the Service Policy Table are
advertised from this port (normal), or if only those
routes that are not listed as 'advertisable' in the
Service Policy Table are advertised (inverse).
|
| a3ipxPCSvcRcvCtl |
.1.3.6.1.4.1.43.2.11.1.1.8 |
|
The object enables or disables the use of the
'receivable' entries in the Service Policy Table.
|
| a3ipxPCSvcRcvType |
.1.3.6.1.4.1.43.2.11.1.1.9 |
|
The object specifies whether only those routes listed
as 'receivable' in the Service Policy Table are
accepted from this port (normal), or if only those
routes that are not listed as 'receivable' in the
Service Policy Table are accepted (inverse).
|
| a3ipxPCNbrAdvCtl |
.1.3.6.1.4.1.43.2.11.1.1.10 |
|
This object enables or disables the use of the
entries in the Neighbor Policy Table that apply
to neighbors to which routing and service
reachability information is advertised.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolNbrType = advertise(2)
or both(3).
NOTE: this object is not supported by NETBuilders
running sw version 8.0 and greater. Its functionality
has been replaced by a3ipxRipPolNbrCtlTable and
a3ipxSapPolNbrCtlTable.
|
| a3ipxPCNbrRcvCtl |
.1.3.6.1.4.1.43.2.11.1.1.11 |
|
The object enables or disables the use of the
entries in the Neighbor Policy Table that apply
to neighbors from which routing and service
reachability information is allowed to be received.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolNbrType = receive(2)
or both(3).
NOTE: this object is not supported by NETBuilders
running sw version 8.0 and greater. Its functionality
has been replaced by a3ipxRipPolNbrCtlTable and
a3ipxSapPolNbrCtlTable.
|
| a3ipxPCNbrRcvType |
.1.3.6.1.4.1.43.2.11.1.1.12 |
|
If this object is set to normal(1), then route
and service reachability information is accepted
only from those neighbors listed in the Neighbor
Policy Table for which a3ipxPolNbrType = receive(2)
or both(3).
If this object is set to inverse(2), then route
and service reachability information is accepted
from any neighbor except those neighbors listed
in the Neighbor Policy Table for which
a3ipxPolNbrType = receive(2) or both(3).
NOTE: this object is not supported by NETBuilders
running sw version 8.0 and greater. Its functionality
has been replaced by a3ipxRipPolNbrCtlTable and
a3ipxSapPolNbrCtlTable.
|
| a3ipxPCPolicyOverride |
.1.3.6.1.4.1.43.2.11.1.1.13 |
|
Policy Override is used to override the configured
policies when the router issues responses to specific
RIP or SAP requests. The configured policies are
always applied for regular RIP or SAP updates.
NOTE: this object is no longer support by NETBuilders
running sw version 8.0 and greater. Its functionality
has been replaced by a3ipxPCRipPolOverride and
a3ipxPCSapPolOverride.
|
| a3ipxPCSvrRplyCtl |
.1.3.6.1.4.1.43.2.11.1.1.14 |
|
This controls whether or not the router is
permitted to respond to 'get nearest server'
requests. If this object has the value
bestSvrReply(1), then this router is permitted
to respond to these requests. If this object
has the value noBestSvrReply(2), this this
router is not permitted to respond to these
requests.
|
| a3ipxPCRipPolOverride |
.1.3.6.1.4.1.43.2.11.1.1.15 |
|
RIP Policy Override is used to override the configured
RIP policies when the router issues responses to specific
RIP requests. The configured policies are always
applied for regular RIP updates.
|
| a3ipxPCSapPolOverride |
.1.3.6.1.4.1.43.2.11.1.1.16 |
|
SAP Policy Override is used to override the configured
policies when the router issues responses to specific
SAP requests. The configured policies are always
applied for regular SAP updates.
|
| a3ipxPolRtePort |
.1.3.6.1.4.1.43.2.11.2.1.1 |
|
The IPX port to which this Receive Route Policy
entry applies.
|
| a3ipxPolRteNet1 |
.1.3.6.1.4.1.43.2.11.2.1.3 |
|
The IPX Network Number for which route information
is accepted or rejected for this port. The value
0xfffffffe is used to represent the default route.
|
| a3ipxPolRteNet2 |
.1.3.6.1.4.1.43.2.11.2.1.4 |
|
When the value of this object is a valid IPX
network and different from a3ipxPolRteNet1, then
this table entries specifies a range of IPX
networks, with the value of a3ipxPolRteNet1
identifying the lower end of the range.
If the value of this object is the same as
a3ipxPolRteNet1, then this table entry
specifies a single IPX network identified by
the value of a3ipxPolRteNet1.
|
| a3ipxPolRteType |
.1.3.6.1.4.1.43.2.11.2.1.2 |
|
This object specifies whether this entry applies
to receiving routes, advertising routes, or both.
|
| a3ipxPolRteStatus |
.1.3.6.1.4.1.43.2.11.2.1.5 |
|
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
|
| a3ipxPolSvcPort |
.1.3.6.1.4.1.43.2.11.3.1.1 |
|
The IPX port to which this Receive Svc Pol
entry applies.
|
| a3ipxPolSvcSvrName |
.1.3.6.1.4.1.43.2.11.3.1.3 |
|
This object contains the name of a server.
A single wildcard (*) is allowed at the end of
the name.
|
| a3ipxPolSvcType |
.1.3.6.1.4.1.43.2.11.3.1.4 |
|
The type of service for which information is accepted
or rejected by this port. The value 'FFFF' acts
as a wildcard for all service types.
|
| a3ipxPolSvcEntryType |
.1.3.6.1.4.1.43.2.11.3.1.2 |
|
This object specifies whether this entry applies
to receiving services, advertising services, or both.
|
| a3ipxPolSvcStatus |
.1.3.6.1.4.1.43.2.11.3.1.5 |
|
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
|
| a3ipxPolNbrPort |
.1.3.6.1.4.1.43.2.11.4.1.1 |
|
The IPX port over which the Trusted Neighbor identified
by this table entry can be reached.
|
| a3ipxPolNbrNet |
.1.3.6.1.4.1.43.2.11.4.1.3 |
|
The IPX Network number identifying the network
to which the neighbor identified by this table
entry is attached.
|
| a3ipxPolNbrAddress |
.1.3.6.1.4.1.43.2.11.4.1.4 |
|
The Mac Address of the Neighbor to whom route and service
reachability information is to be advertised and from which
route and service reachability information is accepted.
|
| a3ipxPolNbrType |
.1.3.6.1.4.1.43.2.11.4.1.2 |
|
This object specifies whether this entry applies
to receiving information, advertising information,
or both.
|
| a3ipxPolNbrStatus |
.1.3.6.1.4.1.43.2.11.4.1.5 |
|
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
|
| a3ipxPolRipNbrCtlPort |
.1.3.6.1.4.1.43.2.11.5.1.1.1 |
|
This NETBuilder port to which this RIP Neighbor
Control entry applies.
|
| a3ipxPolRipNbrCtlAdvCtl |
.1.3.6.1.4.1.43.2.11.5.1.1.2 |
|
This object enables or disables the use of the
entries in the RIP Neighbor Policy Table
(a3ipxPolRipNbrTable) that apply to neighbors
to which routing information is advertised.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolRipNbrType = advertise(2)
or both(3).
|
| a3ipxPolRipNbrCtlRcvCtl |
.1.3.6.1.4.1.43.2.11.5.1.1.3 |
|
The object enables or disables the use of the
entries in the Neighbor Policy Table that apply
to neighbors from which routing information is
allowed to be received.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolRipNbrType = receive(2)
or both(3).
|
| a3ipxPolRipNbrCtlRcvType |
.1.3.6.1.4.1.43.2.11.5.1.1.4 |
|
If this object is set to normal(1), then route
information is accepted only from those neighbors
listed in the Neighbor Policy Table for which
a3ipxPolRipNbrType = receive(2) or both(3).
If this object is set to inverse(2), then route
information is accepted from any neighbor except
those neighbors listed in the Neighbor Policy Table
for which a3ipxPolRipNbrType = receive(2) or both(3).
|
| a3ipxPolRipNbrPort |
.1.3.6.1.4.1.43.2.11.5.2.1.1 |
|
The IPX port over which the Trusted Neighbor identified
by this table entry can be reached.
|
| a3ipxPolRipNbrNet |
.1.3.6.1.4.1.43.2.11.5.2.1.3 |
|
The IPX Network number identifying the network
to which the neighbor identified by this table
entry is attached.
|
| a3ipxPolRipNbrAddress |
.1.3.6.1.4.1.43.2.11.5.2.1.4 |
|
The Mac Address of the Neighbor to whom route
information is to be advertised and from which
route information is accepted.
|
| a3ipxPolRipNbrType |
.1.3.6.1.4.1.43.2.11.5.2.1.2 |
|
This object specifies whether this entry applies
to receiving information, advertising information,
or both.
|
| a3ipxPolRipNbrStatus |
.1.3.6.1.4.1.43.2.11.5.2.1.5 |
|
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
|
| a3ipxPolSapNbrCtlPort |
.1.3.6.1.4.1.43.2.11.5.3.1.1 |
|
This NETBuilder port to which this SAP Neighbor
Control entry applies.
|
| a3ipxPolSapNbrCtlAdvCtl |
.1.3.6.1.4.1.43.2.11.5.3.1.2 |
|
This object enables or disables the use of the
entries in the SAP Neighbor Policy Table
(a3ipxPolSapNbrTable) that apply to neighbors
to which service reachability information
is advertised.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolSapNbrType = advertise(2)
or both(3).
|
| a3ipxPolSapNbrCtlRcvCtl |
.1.3.6.1.4.1.43.2.11.5.3.1.3 |
|
The object enables or disables the use of the
entries in the Neighbor Policy Table that apply
to neighbors from which service reachability
information is allowed to be received.
In other words, this object enables or disables
the use of those entries in the Neighbor Policy
Table for which a3ipxPolSapNbrType = receive(2)
or both(3).
|
| a3ipxPolSapNbrCtlRcvType |
.1.3.6.1.4.1.43.2.11.5.3.1.4 |
|
If this object is set to normal(1), then
service reachability information is accepted
only from those neighbors listed in the Neighbor
Policy Table for which a3ipxPolSapNbrType = receive(2)
or both(3).
If this object is set to inverse(2), then
service reachability information is accepted
from any neighbor except those neighbors listed
in the Neighbor Policy Table for which
a3ipxPolSapNbrType = receive(2) or both(3).
|
| a3ipxPolSapNbrPort |
.1.3.6.1.4.1.43.2.11.5.4.1.1 |
|
The IPX port over which the Trusted Neighbor identified
by this table entry can be reached.
|
| a3ipxPolSapNbrNet |
.1.3.6.1.4.1.43.2.11.5.4.1.3 |
|
The IPX Network number identifying the network
to which the neighbor identified by this table
entry is attached.
|
| a3ipxPolSapNbrAddress |
.1.3.6.1.4.1.43.2.11.5.4.1.4 |
|
The Mac Address of the Neighbor to whom service
reachability information is to be advertised and from which
service reachability information is accepted.
|
| a3ipxPolSapNbrType |
.1.3.6.1.4.1.43.2.11.5.4.1.2 |
|
This object specifies whether this entry applies
to receiving information, advertising information,
or both.
|
| a3ipxPolSapNbrStatus |
.1.3.6.1.4.1.43.2.11.5.4.1.5 |
|
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
|
| a3ipxPolControlTable |
.1.3.6.1.4.1.43.2.11.1 |
|
This table enables and disables the use of policies,
policy attributes and the use of trusted neighbors
and their attributes.
|
| a3ipxPolRteTable |
.1.3.6.1.4.1.43.2.11.2 |
|
The IPX Route Policy Table controls the acceptance
of route reachability information from neighbors and
the advertisement of route reachability information
to neighbors.
If a3ipxPCRteRcvType is configured as normal, a route
is accepted if the network number for the route is in
the list of 'receivable' networks specified in this
table. If a3ipxPCRteRcvType is configure as inverse, a
route is not accepted if the network number for the
route is in the list of 'receivable' networks specified
in this table.
If a3ipxPCRteAdvType is configured as normal, a route
is advertised if the network number for the route is in
the list of 'advertisable' networks specified in this
table. If a3ipxPCRteAdvType is configure as inverse, a
route is not advertised if the network number for the
route is in the list of 'advertisable' networks specified
in this table.
Note, since this table allows ranges of routes to be
specified, all the entries should be examined when
determining if a specific route is affected by these
policies. It is not sufficient to search for an instance
of a3ipxPolRteNet1 that matches the route in question.
|
| a3ipxPolSvcTable |
.1.3.6.1.4.1.43.2.11.3 |
|
The IPX Policy Services Table controls the acceptance
of service reachability information from neighbors
and the advertisement of that information to neighbors.
If a3ipxPCSvcRcvType is configured as normal, a service
is accepted if its port number, server name, and
service type is in the list of tuples specified as
'receivable' by this table. If a3ipxPCSvcRcvType is
configured as inverse, a service is not accepted if its
port number, server name, and service type is in
the list of tuples specified as 'receivable' by this
table.
If a3ipxPCSvcAdvType is configured as normal, a service
is advertised if its network port, server name, and
service type is in the list of tuples specified as
'advertisable' by this table. If a3ipxPCSvcAdvType is
configured as inverse, a service is not advertised if its
port number, server name, and service type is in
the list of tuples specified as 'advertisable' by this
table.
|
| a3ipxPolNbrTable |
.1.3.6.1.4.1.43.2.11.4 |
|
This table defines a set of neighbors to which
the route and service reachability information is
advertised. This table also defines a set of
neighbors from which route and service reachability
information is accepted.
NOTE: this table is not supported by NETBuilders
running sw version 8.0 and greater. The functionality
provided by this table has been replaced by
a3ipxPolRipNbrTable and a3ipxPolSapNbrTable.
|
| a3ipxPolRipNbrCtlTable |
.1.3.6.1.4.1.43.2.11.5.1 |
|
This table enables or disables the use of
the entries in a3ipxPolRipNbrTable. If
the use of the entries in that table is enabled,
this table also controls how they are interpreted.
In one case, RIP updates are accepted only from those
IPX Neighbors listed in a3ipxPolRipNbrTable. In the
other case, RIP updates are accepted only from those
IPX Neighbors not listed in a3ipxPolRipNbrTable.
|
| a3ipxPolRipNbrTable |
.1.3.6.1.4.1.43.2.11.5.2 |
|
This table defines a set of neighbors to which
the route information is advertised. This table
also defines a set of neighbors from which route
information is accepted.
|
| a3ipxPolSapNbrCtlTable |
.1.3.6.1.4.1.43.2.11.5.3 |
|
This table enables or disables the use of
the entries in a3ipxPolSapNbrTable. If
the use of the entries in that table is enabled,
this table also controls how they are interpreted.
In one case, SAP updates are accepted only from those
IPX Neighbors listed in a3ipxPolSapNbrTable. In the
case, SAP updates are accepted only from those
IPX Neighbors not listed in a3ipxPolSapNbrTable.
|
| a3ipxPolSapNbrTable |
.1.3.6.1.4.1.43.2.11.5.4 |
|
This table defines a set of neighbors to which
the service reachability information is advertised.
This table also defines a set of neighbors from which
service reachability information is accepted.
|
