| agentNetProtoStkCapMap |
.1.3.6.1.4.1.298.1.1.4 |
|
This octet string represents the current
protocol stack configuration supported
by the agent, encoded as a bit string.
Each protocol stack is represented
by a single bit. When the value of a
bit = 1, it indicates that the protocol
stack on the agent represented by that
bit is supported; when zero, the protocol
stack is not supported. The number of
octets in the string is always integer
multiple of the octet. The first protocol
stack will encode in the least significant
bit of the first octet. Current, only
IP Stack(bit 0) and IPX Stack(bit 1) were
defined, all other bits should be zero.
|
| agentRunTimeImageMajorVer |
.1.3.6.1.4.1.298.1.1.1.1 |
|
The major software version number of the agent
run time image.
|
| agentRunTimeImageMinorVer |
.1.3.6.1.4.1.298.1.1.1.2 |
|
The minor software version number of the agent
run time image.
|
| agentImageLoadMode |
.1.3.6.1.4.1.298.1.1.1.3 |
|
Tells hub whether the software image is to be
loaded from the FLASH EPROM or from over the network.
|
| agentRemoteBootInfo |
.1.3.6.1.4.1.298.1.1.1.4 |
|
The method for getting boot parameter information.
|
| agentRemoteBootProtocol |
.1.3.6.1.4.1.298.1.1.1.5 |
|
The netboot protocol that used to load the
agent software.
|
| agentRemoteBootFile |
.1.3.6.1.4.1.298.1.1.1.6 |
|
The boot file name that is sent to the boot file
server by agent boot code during boot time.
|
| agentOutBandDialString |
.1.3.6.1.4.1.298.1.1.1.7 |
|
This is the initialization string used by the
Network Management station to establish the
out-of-band connection for modem only.
|
| agentOutBandBaudRate |
.1.3.6.1.4.1.298.1.1.1.8 |
|
The baud rate setting for the out-of-band
port.
|
| agentReset |
.1.3.6.1.4.1.298.1.1.1.9 |
|
The object to allow software to perform
'push_button' system reset.
|
| agentHwReVer |
.1.3.6.1.4.1.298.1.1.3.1 |
|
The hardware reversion number of the network
management module.
|
| agentHwVer |
.1.3.6.1.4.1.298.1.1.3.2 |
|
The hardware model number of the network
management module
|
| agentFwMajorVer |
.1.3.6.1.4.1.298.1.1.2.1 |
|
The major firmware version number of the agent
prom code.
|
| agentFwMinorVer |
.1.3.6.1.4.1.298.1.1.2.2 |
|
The minor firmware version number of the agent
prom code.
|
| ipagentIpAddr |
.1.3.6.1.4.1.298.1.1.5.1.1 |
|
The ipagent's administrative IP address. The
current operational IP address can be obtained
from the ipAdEntAddr in the ipAddrTable. This
parameter will take effect only after reset hub.
This parameter will always be updated in the
EEPROM.
|
| ipagentIpNetMask |
.1.3.6.1.4.1.298.1.1.5.1.2 |
|
The ipagent's administrative IP subnet mask. The
current operational IP subnet mask can be obtained
from the ipAdEntMask in the ipAddrTable. This
parameter will take effect only after reset hub.
This parameter will always be updated in the
EEPROM.
|
| ipagentDefaultGateway |
.1.3.6.1.4.1.298.1.1.5.1.3 |
|
The ipagent's administrative default gateway IP
address. The current operational IP default
gateway IP address can be obtained from the
ipRouteDest in the ipRouteTable. This parameter
will take effect only after reset hub. This
parameter will always be updated in the EEPROM.
|
| ipagentBootServerAddr |
.1.3.6.1.4.1.298.1.1.5.1.4 |
|
The IP address of the boot server that was used
for booting this ipagent. This parameter will
always be updated in the EEPROM.
|
| ipagentUnAuthIP |
.1.3.6.1.4.1.298.1.1.5.1.5 |
|
The IP address of the last station that tried to
access this ipagent with an invalid community
string.
|
| ipagentUnAuthComm |
.1.3.6.1.4.1.298.1.1.5.1.6 |
|
The community string of the last station that tried
to access this ipagent with an invalid community
string.
|
| ipagentTrapRcvrEntry |
.1.3.6.1.4.1.298.1.1.5.2.1 |
|
Destination IP address and community string for
a particular trap server.
|
| concChassisType |
.1.3.6.1.4.1.298.1.3.1.1.1 |
|
The concentrator's chassis type.
|
| concChassisBkplType |
.1.3.6.1.4.1.298.1.3.1.1.2 |
|
The concentrator's chassis backplane type.
|
| concChassisBkplRev |
.1.3.6.1.4.1.298.1.3.1.1.3 |
|
The concentrator's chassis backplane
revision number.
|
| concChassisPsEntry |
.1.3.6.1.4.1.298.1.3.1.1.4.1 |
|
The entry in the table containing the information
about a single power supply.
|
| concChassisFanStatus |
.1.3.6.1.4.1.298.1.3.1.1.5 |
|
The value of this object identifies the
fan status.
|
| concChassisGroupCapacity |
.1.3.6.1.4.1.298.1.3.1.1.6 |
|
The number of groups that can be contained within
the concentrator.
|
| concChassisGroupMap |
.1.3.6.1.4.1.298.1.3.1.1.7 |
|
This octet string represents the current
configuration of groups, encoded as a bit string,
each group is represented by a single bit.
|
| concChassisGrpEntry |
.1.3.6.1.4.1.298.1.3.1.1.8.1 |
|
A list of information for each slot in this chassis.
|
| eSmartHubId |
.1.3.6.1.4.1.298.1.3.2.1.1 |
|
Hub MAC address (octet string) found from prom
chip in hub.
|
| eSmartHubAssignedId |
.1.3.6.1.4.1.298.1.3.2.1.2 |
|
Assigned hub ID for Out-of-Band.
|
| eSmartHubTerSwitch |
.1.3.6.1.4.1.298.1.3.2.1.3 |
|
Status of position of PC/terminal switch located on
rear panel of hub. Switches between serial and
parallel communications for modem/PC or terminal
connection to RS-232 Port. Up (off) for PC,
down (on) for terminal. If position of switch is
changed, there will be no change in this status
until hub is reset.
|
| eSmartHubHwLoadPatStatus |
.1.3.6.1.4.1.298.1.3.2.1.4 |
|
Which logic configuration pattern is loaded into the
Programmable Logic Device PLD.
|
| eSmartHubHwLoadPatCapacity |
.1.3.6.1.4.1.298.1.3.2.1.5 |
|
What kind of function the PLD can perform.
|
| eSmartHubNodeAgeTimer |
.1.3.6.1.4.1.298.1.3.2.1.6 |
|
How long to keep node entry in node summary
table, measured in sec. The maximum is 11 hours.
|
| eSmartHub3in1LnConStatus |
.1.3.6.1.4.1.298.1.3.2.1.7 |
|
Status of 3In1 Uplink which is located on rear
panel of hub. Describes the physical link type
or types currently connected.
|
| eSmartHub3in1StateCtrl |
.1.3.6.1.4.1.298.1.3.2.1.8 |
|
Whether using Auto-sense or manually selected a
particular media type for the uplink connection. If
using Auto-sense it first tries AUI. If
AUI is not present then 10T. If neither AUI nor
10T is present, then it defaults to BNC.
|
| eGlobalHubReadableFrames |
.1.3.6.1.4.1.298.1.3.3.1.1.1 |
|
Global counter of good or readable frames for this
hub. Frame is between 64 and 1518 bytes in
length and has SFD and good FCS.
|
| eGlobalHubMcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.1.2 |
|
Global counter of number of multicast frames for
this hub. 1st bit in highest ordered bytes of
destination address is set to 1. Broadcast packets
are not included.
|
| eGlobalHubBcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.1.3 |
|
Global counter of number of broadcast frames for
his hub. All 1s in network destination address.
Multicast packets are not included.
|
| eGlobalHubFrameTooLongs |
.1.3.6.1.4.1.298.1.3.3.1.1.4 |
|
Global counter, for this hub, of data frames
longer than 1518 bytes, with a SFD and good FCS.
|
| eGlobalHubRunts |
.1.3.6.1.4.1.298.1.3.3.1.1.5 |
|
Global counter, for this hub, of data frames with
size less than 64 bytes, with no CRC or alignment
errors.
|
| eGlobalHubAlignmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.1.6 |
|
Global counter, for this hub, of frames which
are not integer multiples of 1 byte.
|
| eGlobalHubFragmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.1.7 |
|
Global counter, for this hub, of frames greater than
2 bytes and less than 64 bytes, with SFD and bad
FCS (CRC error).
|
| eGlobalHubFCSErrors |
.1.3.6.1.4.1.298.1.3.3.1.1.8 |
|
Global counter, for this hub, of frames that
failed Cyclic Redundancy Check (CRC).
|
| eGlobalHubIFGErrors |
.1.3.6.1.4.1.298.1.3.3.1.1.9 |
|
Global counter, for this hub, of occurrences of
Interframe Gap Errors where time period between
data frames is less than 5.5 micro seconds.
|
| eGlobalHubDataRateMismatch |
.1.3.6.1.4.1.298.1.3.3.1.1.10 |
|
Global counter, for this hub, of errors where
incoming data rate is not with in the tolerance
level of 10MHZ + or - 0.01%.
|
| eGlobalHubShortEvents |
.1.3.6.1.4.1.298.1.3.3.1.1.11 |
|
Global counter, for this hub, of data burst where
data is less than 10 bytes in length, with no
SFD.
|
| eGlobalHubCollisions |
.1.3.6.1.4.1.298.1.3.3.1.1.12 |
|
Global counter of collision flags, for this hub.
|
| eGlobalHubLateCollisions |
.1.3.6.1.4.1.298.1.3.3.1.1.13 |
|
Global counter, for this hub, of collisions
occurring after the 64 byte collision window.
|
| eGlobalHubMJLPs |
.1.3.6.1.4.1.298.1.3.3.1.1.14 |
|
Global counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.
|
| eGlobalHubAutoPartitions |
.1.3.6.1.4.1.298.1.3.3.1.1.15 |
|
Global counter, for this hub, of all ports including
3in1 port being partitioned from network in
response to 31 or more continuous collisions.
|
| eGlobalHubSFDMissing |
.1.3.6.1.4.1.298.1.3.3.1.1.16 |
|
Global counter, for this hub, of a burst of data
greater than or equal to 10 bytes in length with
no SFD.
|
| eGlobalHubBadFrames |
.1.3.6.1.4.1.298.1.3.3.1.1.17 |
|
Global counter, for this hub, of total errored frame
including toolong, runts, misaligned, or bad FCS.
|
| eGrpStatisticsEntry |
.1.3.6.1.4.1.298.1.3.3.1.3.1 |
|
Entry for individual group in table.
|
| ePortStatisticsEntry |
.1.3.6.1.4.1.298.1.3.3.1.4.1 |
|
Entry for individual port in table.
|
| eTrafficMatrixEntry |
.1.3.6.1.4.1.298.1.3.3.1.5.1 |
|
Individual entry in matrix of packet lengths table.
|
| eColGraphBar |
.1.3.6.1.4.1.298.1.3.3.1.6.1.1 |
|
Information on hardware LED collision graph bar.
|
| eUtilGraphBar |
.1.3.6.1.4.1.298.1.3.3.1.6.1.2 |
|
Information on hardware LED for utilization
graph bar.
|
| ePortRateEntry |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1 |
|
Individual entry in port rate table.
|
| ePortStateCtrlEntry |
.1.3.6.1.4.1.298.1.3.4.1.1.1 |
|
Individual entry of port control in table.
|
| nodeSummaryEntry |
.1.3.6.1.4.1.298.1.3.5.1.1 |
|
Individual entry in node summary table.
|
| nodeSecuLev1Entry |
.1.3.6.1.4.1.298.1.3.5.2.1.1 |
|
Individual entry for node security table.
|
| thresholdLev1Entry |
.1.3.6.1.4.1.298.1.3.6.1.1.1 |
|
Individual entry in threshold trap table.
|
| ipagentTrapRcvrIpAddr |
.1.3.6.1.4.1.298.1.1.5.2.1.1 |
|
IP address for trap server receiving trap.
|
| ipagentTrapRcvrStatus |
.1.3.6.1.4.1.298.1.1.5.2.1.2 |
|
Validation of individual trap receiver. If value
of this object is set to invalid(3), then that
particular entry is deemed invalid, meaning that
the address for that entry is no longer valid
because the entry has been removed from the table.
|
| ipagentTrapRcvrComm |
.1.3.6.1.4.1.298.1.1.5.2.1.3 |
|
Community string for traps sent to this trap
receiver.
|
| concChassisPsIndex |
.1.3.6.1.4.1.298.1.3.1.1.4.1.1 |
|
The value of this object identifies the
power supply table for which this entry
contains power supply type and status.
|
| concChassisPsModuleType |
.1.3.6.1.4.1.298.1.3.1.1.4.1.2 |
|
The value of this object identifies the
power supply module type.
|
| concChassisPsStatus |
.1.3.6.1.4.1.298.1.3.1.1.4.1.3 |
|
The value of this object identifies the
power supply module status.
|
| concChassisGrpIndex |
.1.3.6.1.4.1.298.1.3.1.1.8.1.1 |
|
The value of this object identifies the
chassis group table for which this entry
contains group related information.
|
| concChassisGrpNumberPort |
.1.3.6.1.4.1.298.1.3.1.1.8.1.2 |
|
The number of port is available for up/down link
within this group.
|
| concChassisGrpType |
.1.3.6.1.4.1.298.1.3.1.1.8.1.3 |
|
The value represents the function of this group.
|
| concChassisGrpDescr |
.1.3.6.1.4.1.298.1.3.1.1.8.1.4 |
|
A description of this group device.
|
| concChassisGrpHwRev |
.1.3.6.1.4.1.298.1.3.1.1.8.1.5 |
|
The hardware revision number of this particular
group.
|
| eGrpStatIndex |
.1.3.6.1.4.1.298.1.3.3.1.3.1.1 |
|
The value of this object identifies the group
for which this entry contains group statistical
information.
|
| eGrpStatReadableFrames |
.1.3.6.1.4.1.298.1.3.3.1.3.1.2 |
|
Group counter of 'good' or readable frames. Frame
is between 64 and 1518 bytes in length and
has SFD and good FCS.
|
| eGrpStatMcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.3.1.3 |
|
Group counter of number of muliticast frames.
1st bit in highest ordered bytes of destination
address is set to 1. Broadcast packets are not
included.
|
| eGrpStatBcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.3.1.4 |
|
Group counter of number of broadcast frames. All
1s in network destination address. Multicast
packets are not included.
|
| eGrpStatFrameTooLongs |
.1.3.6.1.4.1.298.1.3.3.1.3.1.5 |
|
Group counter for data frames longer than 1518
bytes, with a SFD and good FCS.
|
| eGrpStatRunts |
.1.3.6.1.4.1.298.1.3.3.1.3.1.6 |
|
Group counter for data frames with size less than
64 bytes, with no CRC or alignment errors.
|
| eGrpStatAlignmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.3.1.7 |
|
Group counter of frames which are not integer
multiples of 1 byte .
|
| eGrpStatFragmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.3.1.8 |
|
Group counter of frames greater than 2 bytes and
less than 64 bytes, with SFD and bad FCS
(CRC error).
|
| eGrpStatFCSErrors |
.1.3.6.1.4.1.298.1.3.3.1.3.1.9 |
|
Group counter frames that failed Cyclic
Redundancy Check (CRC).
|
| eGrpStatIFGErrors |
.1.3.6.1.4.1.298.1.3.3.1.3.1.10 |
|
Group counter of Interframe Gap Errors
where time period between data frames is less than
5.5 micro seconds.
|
| eGrpStatDataRateMismatch |
.1.3.6.1.4.1.298.1.3.3.1.3.1.11 |
|
Group counter of errors where incoming data rate
is not with in the tolerance level of
10 MHZ + or - 0.01%.
|
| eGrpStatShortEvents |
.1.3.6.1.4.1.298.1.3.3.1.3.1.12 |
|
Group counter of data burst where data is less than
10 bytes in length, with no SFD.
|
| eGrpStatCollisions |
.1.3.6.1.4.1.298.1.3.3.1.3.1.13 |
|
Group counter of collision flags.
|
| eGrpStatLateCollisions |
.1.3.6.1.4.1.298.1.3.3.1.3.1.14 |
|
Group counter of collisions occurring after the 64
byte collision window.
|
| eGrpStatMJLPs |
.1.3.6.1.4.1.298.1.3.3.1.3.1.15 |
|
Group counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.
|
| eGrpStatAutoPartitions |
.1.3.6.1.4.1.298.1.3.3.1.3.1.16 |
|
Group counter of ports in group autopartitioned in
response to 31 or more continuous collisions.
|
| eGrpStatSFDMissing |
.1.3.6.1.4.1.298.1.3.3.1.3.1.17 |
|
Group counter of a burst of data greater than or
equal to 10 bytes in length with no SFD.
|
| eGrpStatBadFrames |
.1.3.6.1.4.1.298.1.3.3.1.3.1.18 |
|
Group counter of total errored frames including
toolong, runts, misaligned, or bad FCS.
|
| ePortGrpIndex |
.1.3.6.1.4.1.298.1.3.3.1.4.1.1 |
|
The value of this object identifies the group for
which this entry contains port statistical
information.
|
| ePortIndex |
.1.3.6.1.4.1.298.1.3.3.1.4.1.2 |
|
The value of this object identifies the port for
which this entry contains port statistical
information.
|
| ePortStatReadableFrames |
.1.3.6.1.4.1.298.1.3.3.1.4.1.3 |
|
Port counter of good or readable frames. Frame is
between 64 and 1518 bytes in length and
has SFD and good FCS.
|
| ePortStatMcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.4.1.4 |
|
Port counter of number of muliticast frames. 1st
bit in highest ordered bytes of destination address
is set to 1. Broadcast packets are not included.
|
| ePortStatBcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.4.1.5 |
|
Port counter of number of broadcast frames. All
1s in network destination address. Multicast
packets are not included.
|
| ePortStatFrameTooLongs |
.1.3.6.1.4.1.298.1.3.3.1.4.1.6 |
|
Port counter for data frames longer than 1518
bytes, with a SFD and good FCS.
|
| ePortStatRunts |
.1.3.6.1.4.1.298.1.3.3.1.4.1.7 |
|
Port counter for data frames with size less than
64 bytes, with no CRC or alignment errors.
|
| ePortStatAlignmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.4.1.8 |
|
Port counter of frames which are not integer
multiples of 1 byte.
|
| ePortStatFragmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.4.1.9 |
|
Port counter of frames greater than 2 bytes and
less than 64 bytes, with SFD and bad
FCS (CRC error).
|
| ePortStatFCSErrors |
.1.3.6.1.4.1.298.1.3.3.1.4.1.10 |
|
Port counter of frames that failed Cyclic
Redundancy Check (CRC).
|
| ePortStatIFGErrors |
.1.3.6.1.4.1.298.1.3.3.1.4.1.11 |
|
Port counter of Interframe Gap Errors where
time period between data frames is less than 5.5
micro seconds.
|
| ePortStatDataRateMismatch |
.1.3.6.1.4.1.298.1.3.3.1.4.1.12 |
|
Port counter of errors where incoming data rate
is not with in the tolerance level of
10 MHZ + or - 0.01%.
|
| ePortStatShortEvents |
.1.3.6.1.4.1.298.1.3.3.1.4.1.13 |
|
Port counter of data burst where data is less than
10 bytes in length, with no SFD.
|
| ePortStatCollisions |
.1.3.6.1.4.1.298.1.3.3.1.4.1.14 |
|
Port counter of collision flags.
|
| ePortStatLateCollisions |
.1.3.6.1.4.1.298.1.3.3.1.4.1.15 |
|
Port counter of collisions occurring after the 64
byte collision window.
|
| ePortStatMJLPs |
.1.3.6.1.4.1.298.1.3.3.1.4.1.16 |
|
Port counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.
|
| ePortStatAutoPartitions |
.1.3.6.1.4.1.298.1.3.3.1.4.1.17 |
|
Port counter of number of times port was
autopartitioned in response to 31 or more
continuous collisions.
|
| ePortStatSFDMissing |
.1.3.6.1.4.1.298.1.3.3.1.4.1.18 |
|
Port counter of a burst of data greater than or
equal to 10 bytes in length with no SFD.
|
| ePortStatBadFrames |
.1.3.6.1.4.1.298.1.3.3.1.4.1.19 |
|
Port counter of total errored frames including
toolong, runts, misaligned, or bad FCS.
|
| eTrafficMatrixLength |
.1.3.6.1.4.1.298.1.3.3.1.5.1.1 |
|
Starting length for each range in table.
|
| eTrafficMatrixRange |
.1.3.6.1.4.1.298.1.3.3.1.5.1.2 |
|
Range of packet sizes to be scanned for in network
traffic.
|
| eTrafficMatrixFramesCount |
.1.3.6.1.4.1.298.1.3.3.1.5.1.3 |
|
Counter for number of frames received for
particular range specified by the MatrixRange.
|
| ePortRateGrpIndex |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.1 |
|
The value of this object identifies the group for
which this entry contains port statistical
information.
|
| ePortRatePortIndex |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.2 |
|
This value identifies the port for which
this entry contains port statistical information.
|
| ePortRateReadableFrames |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.3 |
|
Rate of occurrence of good or readable frames.
|
| ePortRateMcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.4 |
|
Rate of occurrence of number of muliticast frames.
1st bit in highest ordered bytes of destination
address is set to 1. Broadcast packets are
not included.
|
| ePortRateBcastFrames |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.5 |
|
Rate of occurrence of number of broadcast frames.
All 1s in network destination address. Multicast
packets are not included.
|
| ePortRateFrameTooLongs |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.6 |
|
Rate of occurrence of data frames longer than 1518
bytes, with a SFD and good FCS.
|
| ePortRateRunts |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.7 |
|
Rate of occurrence of data frames with size less
than 64 bytes, with no CRC or alignment errors.
|
| ePortRateAlignmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.8 |
|
Rate of occurrence of frames which are not integer
multiples of 1 byte.
|
| ePortRateFragmentErrors |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.9 |
|
Rate of occurrence of frames greater than 2 bytes
and less than 64 bytes, with SFD and bad
FCS (CRC error).
|
| ePortRateFCSErrors |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.10 |
|
Rate of occurrence of frames that failed Cyclic
Redundancy Check (CRC).
|
| ePortRateIFGErrors |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.11 |
|
Rate of occurrence of interframe Gap Errors where
time period between data frames is less than 5.5
micro seconds.
|
| ePortRateDataRateMismatch |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.12 |
|
Rate of occurrence of errors where incoming data
rate is not with in the tolerance level of
10 MHz + or - 0.01%.
|
| ePortRateShortEvents |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.13 |
|
Rate of occurrence of data burst where data is less
than 10 bytes in length, with no SFD.
|
| ePortRateCollisions |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.14 |
|
Rate of occurrence of collision flags.
|
| ePortRateLateCollisions |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.15 |
|
Rate of occurrence of collisions occurring after the
64 byte collision window.
|
| ePortRateMJLPs |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.16 |
|
Rate of occurrence of MAU jabber lockup
protection where hub repeater chip goes into
lockup state.
|
| ePortRateAutoPartitions |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.17 |
|
Rate of occurrence of times port was
autopartitioned in response to 31 or
more continuous collisions.
|
| ePortRateSFDMissing |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.18 |
|
Rate of occurrence of a burst of data greater than
or equal to 10 bytes in length with no SFD.
|
| ePortRateBadFrames |
.1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.19 |
|
Rate of occurrence of total errored frames
including toolong, runts, misaligned, or bad FCS.
|
| ePortStateGrpIndex |
.1.3.6.1.4.1.298.1.3.4.1.1.1.1 |
|
The value of this object identifies the group for
which this entry contains port control information.
|
| ePortStatePortIndex |
.1.3.6.1.4.1.298.1.3.4.1.1.1.2 |
|
This value identifies the port for which this
entry contains port control information.
|
| ePortStateType |
.1.3.6.1.4.1.298.1.3.4.1.1.1.3 |
|
Type of cabling physically connected to port.
|
| ePortStateLinkStatus |
.1.3.6.1.4.1.298.1.3.4.1.1.1.4 |
|
Link status for particular port. On=physical link
if link test enabled. Off=no physical link
exists or link test is disabled.
|
| ePortStateLinkIntegTest |
.1.3.6.1.4.1.298.1.3.4.1.1.1.5 |
|
Set can enable or disabled link integrity test.
Get will say if link integrity test is enabled (2)
or disabled (3).
|
| ePortStateAutoPartStatus |
.1.3.6.1.4.1.298.1.3.4.1.1.1.6 |
|
Whether port has been autopartitioned (2) or not
autopartitioned (3).
|
| ePortStateJabberStatus |
.1.3.6.1.4.1.298.1.3.4.1.1.1.7 |
|
Jabber detection for port. If On(2), then
jabber occurred on this port. Off(3), then no jabber
occurred or jabber detection has been manually
disabled.
|
| ePortStateJabberState |
.1.3.6.1.4.1.298.1.3.4.1.1.1.8 |
|
Set can enable or disable jabber detection test. Get
will say if jabber detection test is enabled (2)
or disabled (3).
|
| ePortStateAdminState |
.1.3.6.1.4.1.298.1.3.4.1.1.1.9 |
|
Set will manually enable or disable any port. Get
will say if port has been enabled (2) or
disabled (3).
|
| ePortStateRDTState |
.1.3.6.1.4.1.298.1.3.4.1.1.1.10 |
|
Whether RecvThreshold has been enabled or
disabled. Can use this to lower noise threshold
(tolerance) so that longer twisted pair links
can be used.
|
| ePortStatePolarityStatus |
.1.3.6.1.4.1.298.1.3.4.1.1.1.11 |
|
Polarity is correct (2) or not for this port.
|
| ePortStatePolarityState |
.1.3.6.1.4.1.298.1.3.4.1.1.1.12 |
|
Autopolarity correction enabled or disabled.
Allows hub to make electrical corrections
automatically if cable does not reverse polarity
within wire pairs. If do not want this correction to
take place, autocorrection can be disabled.
|
| nodeSummaryGrpIndex |
.1.3.6.1.4.1.298.1.3.5.1.1.1 |
|
Group Id for identifying the group
where node activity is detected.
|
| nodeSummaryPortIndex |
.1.3.6.1.4.1.298.1.3.5.1.1.2 |
|
Port Id for identifying the port where
node activity is detected.
|
| nodeSummarySrcMacAddr |
.1.3.6.1.4.1.298.1.3.5.1.1.3 |
|
The source MAC address of the node
that is transmitting frames
received by this port.
|
| nodeSummaryDestMacAddr |
.1.3.6.1.4.1.298.1.3.5.1.1.4 |
|
The destination MAC address of the
node to which frames are being
received by this port.
|
| nodeSummaryEtherType |
.1.3.6.1.4.1.298.1.3.5.1.1.5 |
|
The 2 bytes after the source (src) address
in packet.
|
| nodeSummaryIpAddrPair |
.1.3.6.1.4.1.298.1.3.5.1.1.6 |
|
Destination and source IP address if packet is
an Ethernet IP packet. It the packet is not an
Ethernet IP packet, then the information may
not be accurate.
|
| nodeSecuLev1GrpIndex |
.1.3.6.1.4.1.298.1.3.5.2.1.1.1 |
|
Group ID for port which verifying node access.
|
| nodeSecuLev1PortIndex |
.1.3.6.1.4.1.298.1.3.5.2.1.1.2 |
|
Specific port for which verifying node access.
|
| nodeSecuLev1Status |
.1.3.6.1.4.1.298.1.3.5.2.1.1.3 |
|
Address is valid or invalid.
|
| nodeSecuLev1AllowedAddr |
.1.3.6.1.4.1.298.1.3.5.2.1.1.4 |
|
MAC address of nodes allowed for particular port.
|
| nodeSecuLev1Action |
.1.3.6.1.4.1.298.1.3.5.2.1.1.5 |
|
Set action for node intrusion violation.
|
| thresholdLev1Index |
.1.3.6.1.4.1.298.1.3.6.1.1.1.1 |
|
An index that uniquely identifies an entry in the
alarm table.
|
| thresholdLev1Status |
.1.3.6.1.4.1.298.1.3.6.1.1.1.2 |
|
Status of entry in threshold/trap table.
|
| thresholdLev1Target |
.1.3.6.1.4.1.298.1.3.6.1.1.1.3 |
|
Set target for threshold definition. Either whole
hub(2) or particular port (3).
|
| thresholdLev1GroupIndex |
.1.3.6.1.4.1.298.1.3.6.1.1.1.4 |
|
Group ID for trap set. One note--if the
target is selected as hub, the group index
will be ignored.
|
| thresholdLev1PortIndex |
.1.3.6.1.4.1.298.1.3.6.1.1.1.5 |
|
Port number for trap set. One note--if the
target is selected as hub, the port index
will be ignored.
|
| thresholdLev1Subject |
.1.3.6.1.4.1.298.1.3.6.1.1.1.6 |
|
Variable checking for in trap. These are the type
of frames that a trap will be verified against.
|
| thresholdLev1SampleType |
.1.3.6.1.4.1.298.1.3.6.1.1.1.7 |
|
The method of sampling the selected variable
and calculating the value to be compared
against the threshold.
|
| thresholdLev1StartupAlarm |
.1.3.6.1.4.1.298.1.3.6.1.1.1.8 |
|
When the trap is triggered in relation to value set.
When goes above (2), below (3), or changes at
all from (4).
|
| thresholdLev1WaterMark |
.1.3.6.1.4.1.298.1.3.6.1.1.1.9 |
|
Counter of threshold.
|
| thresholdLev1DetectedValue |
.1.3.6.1.4.1.298.1.3.6.1.1.1.10 |
|
The value of the statistic for the last
sampling period.
|
| thresholdLev1RisingEvent |
.1.3.6.1.4.1.298.1.3.6.1.1.1.11 |
|
How to respond to a triggered event for a
rising event.
|
| thresholdLev1FallingEvent |
.1.3.6.1.4.1.298.1.3.6.1.1.1.12 |
|
How to respond to a triggered event for a
falling event.
|
| thresholdLev1Interval |
.1.3.6.1.4.1.298.1.3.6.1.1.1.13 |
|
The interval in seconds over which the data is
sampled.
|
| thresholdLev1OwnerString |
.1.3.6.1.4.1.298.1.3.6.1.1.1.14 |
|
8-byte octet reserved for the owner who
defined this entry.
|
