| cAdslAtucCapCurrState |
.1.3.6.1.4.1.9.9.149.1.2.1.1 |
|
This object specifies the state of the ATU-C transceiver.
The value of this managed is 'idle' for an ATU-C that has
been provisioned, but is not physically present in the system.
|
| cAdslAtucCapCurrRxGain |
.1.3.6.1.4.1.9.9.149.1.2.1.2 |
|
This managed object represents the gain applied to the ATU-C
receiver.
The value of this managed object is '0' for an ATU-C that has
been provisioned, but is not physically present in the system.
|
| cAdslAtucCapCurrRxSnr |
.1.3.6.1.4.1.9.9.149.1.2.1.3 |
|
This managed object represents the signal-to-noise ratio
measured across the the ATU-C receive pair.
The value of this managed object is '0' for an ATU-C that has
been provisioned, but is not physically present in the system.
|
| cAdslAturCapCurrRxGain |
.1.3.6.1.4.1.9.9.149.1.3.1.1 |
|
This managed object represents the gain applied to the ATU-R
receiver.
The value of this managed object is '0' if the corresponding
ATU-C has been provisioned, but is not physically present in
the system.
|
| cAdslAtucCapPerfInitFailures |
.1.3.6.1.4.1.9.9.149.1.6.1.1 |
|
This object specifies the number of line initialization
failures relative to sysUpTime.
|
| cAdslAtucCapPerfCurr15MinInitFailures |
.1.3.6.1.4.1.9.9.149.1.6.1.2 |
|
This object specifies the number of line initialization
failures in the current 15-minute interval.
|
| cAdslAtucCapPerfCurr1DayInitFailures |
.1.3.6.1.4.1.9.9.149.1.6.1.3 |
|
This object specifies the number of line initialization
failures in the current 1-day interval.
|
| cAdslAtucCapPerfPrev1DayInitFailures |
.1.3.6.1.4.1.9.9.149.1.6.1.4 |
|
This object specifies the number of line initialization
failures in the previous 1-day interval.
|
| cAdslAtucCapIntervalInitFailures |
.1.3.6.1.4.1.9.9.149.1.8.1.1 |
|
This object specifies the number of line initialization
failures in the interval.
|
| cAdslLineCapConfTrainingMode |
.1.3.6.1.4.1.9.9.149.1.14.1.1 |
|
This object specifies the mode employed by the ATU-C and
ATU-R when training against each other. One of two training
modes can be employed:
- Standard
An ATU-C initiates a training sequence using the method
defined by T1E1.4/99-161R3. This training mode is the
default for ADSL modems employing the CAP line code.
- Fast
An ATU-C initiates a vendor-specific training sequence that
can possibly provide a shorter training sequence.
|
| cAdslLineCapConfInterleaveDelay |
.1.3.6.1.4.1.9.9.149.1.14.1.2 |
|
This object specifies the interleave delay for the
downstream channel. The value of this object specifies the
mapping (relative spacing) between subsequent input bytes at
the interleaver input and their placement in the bit stream
at the interleaver output. The value 'long' provides greater
separation between consecutive input bytes in the output bit
stream, thereby allowing for improved impulse noise immunity
at the expense of payload latency.
|
| cAdslLineCapConfCpeSignature |
.1.3.6.1.4.1.9.9.149.1.14.1.3 |
|
This object specifies the value of the minimum CPE signature
expected from ATU-R during training. The value of the CPE
signature corresponds to the software version of the ATU-R.
If the CPE signature advertised by an ATU-R is less than the
value of this object, then the ATU-C will be placed into an
idle state, thereby preventing the line from training.
In addition, the agent increments the value of the
cAdslAtucCapPerfInitFailures object for each attempt to train
by an ATU-R advertising a CPE signature less than the value of
this object. When a management client observes the value of
cAdslAtucCapPerfInitFailures increasing, it should retrieve the
value of the adslAturInvSerialNumber object (for more details,
see the ADSL-LINE-MIB) . This value of this object reflects the
CPE signature advertised by an ATU-R implementing the CAP line
code. If the CPE signature of the ATU-R is not known, the value
of the adslAturInvSerialNumber object should be a zero-length
string.
|
| cAdslAtucCapConfTargetSnrMgn |
.1.3.6.1.4.1.9.9.149.1.14.1.4 |
|
This object specifies the target SNR margin. This is the
desired noise margin the ATU-C must achieve with a BER of
10-7 or better to successfully complete training.
|
| cAdslAtucCapConfMinTxRate |
.1.3.6.1.4.1.9.9.149.1.14.1.5 |
|
This object specifies the minimum acceptable downstream
line rate.
|
| cAdslAtucCapConfMaxTxRate |
.1.3.6.1.4.1.9.9.149.1.14.1.6 |
|
This object specifies the desired line rate which the ATU-C
will attempt to train at.
|
| cAdslAtucCapConfDown136KBaudEnable |
.1.3.6.1.4.1.9.9.149.1.14.1.7 |
|
This object specifies whether the modem can train the
downstream channel using a symbol rate of 136K symbols
per second.
|
| cAdslAtucCapConfUp68KBaudEnable |
.1.3.6.1.4.1.9.9.149.1.14.1.8 |
|
This object specifies whether the modem can train the
upstream channel using a symbol rate of 68K symbols
per second.
The value of this object does not effect whether the modem
can train at any other symbol rate; that is, the values of
this object and cAdslAtucCapConfUp17KBaudEnable are not
mutually exclusive.
|
| cAdslAtucCapConfUp17KBaudEnable |
.1.3.6.1.4.1.9.9.149.1.14.1.9 |
|
This object specifies whether the modem can train the
upstream channel using a symbol rate of 17K symbols
per second.
The value of this object does not effect whether the modem
can train at any other symbol rate; that is, the values of
this object and cAdslAtucCapConfUp68KBaudEnable are not
mutually exclusive.
|
| cAdslAtucCapConfPsdmLevel |
.1.3.6.1.4.1.9.9.149.1.14.1.10 |
|
This managed object specifies the nominal power output of the
ATU-C across the entire transmit spectrum. Observe that this
implies the attenuation of the signal for some data rates.
This value does not take effect until the modem has retrained
against the ATU-C to which the ATU-R has a connection.
|
| cAdslAturCapConfTargetSnrMgn |
.1.3.6.1.4.1.9.9.149.1.14.1.11 |
|
This object specifies the target SNR margin. This is the
desired noise margin the ATU-R must achieve with a BER of
10-7 or better to successfully complete training.
|
| cAdslAturCapConfMinTxRate |
.1.3.6.1.4.1.9.9.149.1.14.1.12 |
|
This object specifies the minimum acceptable upstream
line rate.
|
| cAdslAturCapConfMaxTxRate |
.1.3.6.1.4.1.9.9.149.1.14.1.13 |
|
This object specifies the desired line rate which the ATU-R
will attempt to train at.
|
| cAdslAturCapConfPsdmLevel |
.1.3.6.1.4.1.9.9.149.1.14.1.14 |
|
This managed object specifies the nominal power output of the
ATU-R across the entire transmit spectrum. Observe that this
implies the attenuation of the signal for some data rates.
This value does not take effect until the modem has retrained
against the ATU-C to which the ATU-R has a connection.
|
