| ciscoAtmVplCastType |
.1.3.6.1.4.1.9.10.13.1.1.1.1.1 |
|
Vpl type is either a point to point connection or point
to multipoint root or leaf.
|
| ciscoAtmVplSpanType |
.1.3.6.1.4.1.9.10.13.1.1.1.1.2 |
|
Vpl span is either a transit one or a terminating one.
|
| ciscoAtmVplConfigType |
.1.3.6.1.4.1.9.10.13.1.1.1.1.3 |
|
Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg.
The half leg can be set to Passive through user configuration only.
|
| ciscoAtmVplRxUpcMode |
.1.3.6.1.4.1.9.10.13.1.1.1.1.4 |
|
Usage Parameter Control opeartion is pass,tag,drop or
local shaping at this connection.
|
| ciscoAtmVplConnState |
.1.3.6.1.4.1.9.10.13.1.1.1.1.5 |
|
The connection state of this VPL.
|
| ciscoAtmVplOamLoopbkTxInterval |
.1.3.6.1.4.1.9.10.13.1.1.1.1.6 |
|
Frequency of OAM loopback cells generated.
|
| ciscoAtmVplOamSegmentLoopback |
.1.3.6.1.4.1.9.10.13.1.1.1.1.7 |
|
Enable segment loopback on this virtual path.
|
| ciscoAtmVplOamEndLoopback |
.1.3.6.1.4.1.9.10.13.1.1.1.1.8 |
|
Enable end to end loopback on this virtual path.
|
| ciscoAtmVplOamAisEnable |
.1.3.6.1.4.1.9.10.13.1.1.1.1.9 |
|
Enable Alarm Indication Signal OAM cell generation
if the interafce goes down on a crossconnect virtual path.
|
| ciscoAtmVplOamRdiEnable |
.1.3.6.1.4.1.9.10.13.1.1.1.1.10 |
|
Enable Remote Defect Indication OAM cell generation
if an Alarm Indication Signal OAM cell is received.
|
| ciscoAtmVplInstallTime |
.1.3.6.1.4.1.9.10.13.1.1.1.1.11 |
|
The time stamp derived from sysUpTime when this VPL gets
created. The VPL entries are created/deleted as a by-product
of creating and deleting entries in the atmVplTable defined
in RFC1695.
|
| ciscoAtmVplInCells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.12 |
|
The total number of cells received on this
VPL.
|
| ciscoAtmVplOutCells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.13 |
|
The total number of cells transmitted on
this VPL.
|
| ciscoAtmVplCrossIfIndex |
.1.3.6.1.4.1.9.10.13.1.1.1.1.14 |
|
For point to point, this is the cross-connected VPL's
ifIndex of this VPL. For point to multi-point connection,
this will be the root VPL's ifIndex for a leaf VPL entry in
the multicast chain, or it's the 1st leaf for a root VPL entry.
If it's zero, it means it's not cross-connected yet.
Atomically set ciscoAtmVplConnState, ciscoAtmVplCrossIfIndex
and ciscoAtmVplCrossVpi will create or delete a cross
connection to crossed half leg of this ciscoAtmVplCrossIfindex
and ciscoAtmVplCrossVpi for p2p PVP, or add or drop a multicast
connection of this ciscoAtmVplCrossIfindex and
ciscoAtmVplCrossVpi to/from the root on the multicast chain
for p2mp PVP.
|
| ciscoAtmVplCrossVpi |
.1.3.6.1.4.1.9.10.13.1.1.1.1.15 |
|
This specifies the VPI value of the VPL to which this VPL is
cross-connected. For point to multi-point connection, this is
the root VPL's VPI for the leaf entry. Similarly it is the
1st leaf's VPI value for the root entry.
|
| ciscoAtmVplNextLeafIfIndex |
.1.3.6.1.4.1.9.10.13.1.1.1.1.16 |
|
For point to point, this is zero i.e. not used.
For point to multi-point connection, this will be the next
leaf VPL's ifIndex on the multicast chain. This will be 0
if this is the root VPL entry. If it's zero for a leaf VPL,
it means this is the last leaf.
|
| ciscoAtmVplNextLeafVpi |
.1.3.6.1.4.1.9.10.13.1.1.1.1.17 |
|
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VPL's VPI on the multicast chain.
|
| ciscoAtmVplRemoteAddr |
.1.3.6.1.4.1.9.10.13.1.1.1.1.18 |
|
Soft PVP target address if this is the calling side
Soft PVP source address if this is called side.
Atomically set ConnState, RemoteAddr
and RemoteVpi will create or delete a soft PVP.
Atomically set ConnState, RemoteAddr without RemoteVpi will
also create or delete a soft PVP but let target switch
assign the vpi.
|
| ciscoAtmVplRemoteVpi |
.1.3.6.1.4.1.9.10.13.1.1.1.1.19 |
|
Soft PVP target VPI in calling side. 0 in called side.
|
| ciscoAtmVplLocation |
.1.3.6.1.4.1.9.10.13.1.1.1.1.20 |
|
Indicate calling or called side of a soft PVP.
If ciscoAtmVplConfigType is not soft then
ciscoAtmVplLocation value should be ignored.
|
| ciscoAtmVplSlowRetryIntv |
.1.3.6.1.4.1.9.10.13.1.1.1.1.21 |
|
Soft PVP slow retry interval time in seconds.
|
| ciscoAtmVplNumAttempts |
.1.3.6.1.4.1.9.10.13.1.1.1.1.22 |
|
Number of retries made to install this soft PVP
connection. If ciscoAtmVplConfigType is not soft then
ciscoAtmVplNumAttempts value should be ignored.
|
| ciscoAtmVplLastReleaseCause |
.1.3.6.1.4.1.9.10.13.1.1.1.1.23 |
|
Value of the Cause field of the Cause
Information Element in the last Release
Signalling message received for this SPVP.
Indicates the reason for the Release.
ciscoAtmVplConfigType is not soft then
ciscoAtmVplLastReleaseCause value should be ignored.
|
| ciscoAtmVplLogicalPortDef |
.1.3.6.1.4.1.9.10.13.1.1.1.1.24 |
|
Indicates whether the VPC at this VPL interface
is an Atm Logical Port interface.
|
| ciscoAtmVplLogicalPortIndex |
.1.3.6.1.4.1.9.10.13.1.1.1.1.25 |
|
The ifTable index of the Atm logical port
interface associated with this VPL. Only valid if
the value of atmVplLogicalPortDef is isLogicalIf,
and the VPL row is active.
|
| ciscoAtmVplUpcViolations |
.1.3.6.1.4.1.9.10.13.1.1.1.1.26 |
|
The total number of nonconforming cells detected
by Usage Parameter Control (UPC) for cells received
on this VPL.
On LS1010 systems, this counter is valid only if
equipped with the Feature Card - Per Flow Queueing.
|
| ciscoAtmVplEpdTpdCellDrops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.27 |
|
Never implemented.
|
| ciscoAtmVplEpdTpdPacketDrops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.28 |
|
Never implemented.
|
| ciscoAtmVplEpdTpdPacketsIn |
.1.3.6.1.4.1.9.10.13.1.1.1.1.29 |
|
Never implemented.
|
| ciscoAtmVplClp1Drops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.30 |
|
Never implemented.
|
| ciscoAtmVplDefaultRxUpcTolerance |
.1.3.6.1.4.1.9.10.13.1.1.1.1.31 |
|
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum
Burst Size for VBR connectons) requested for Usage
Parameter Control is not explicitly specified in VPL creation,
this object contains the default that is used. If tolerance
is explicitly specified in VPL creation, it can be found in
the Traffic Table row specified by atmVplReceiveTrafficDescrIndex,
and the value of this object is -1.
|
| ciscoAtmVplDefaultRxUpcVbrCdvt |
.1.3.6.1.4.1.9.10.13.1.1.1.1.32 |
|
If the Cell Delay Variation Tolerance (CDVT) requested for
Usage Parameter Control for a VBR connection is not explicitly
specified in VPL creation, this object contains the default
that is used. If CDVT is explicitly specified in VPL creation,
it can be found in the Traffic Table row specified by
atmVplReceiveTrafficDescrIndex, and the value of this object
is -1.
|
| ciscoAtmVplLsPerVcqWrrWeight |
.1.3.6.1.4.1.9.10.13.1.1.1.1.33 |
|
Configure the weighting specified for a VP half-leg
within a service class to make the scheduling decision
among other active VPLs in the service class. This
is for transmit on the VPL on the interface. This
parameter only applies to transit VPs. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVplLsPerVcqTunnelIsShaped |
.1.3.6.1.4.1.9.10.13.1.1.1.1.34 |
|
Determines whether this is to be a -shaped- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a shaped VP Tunnel.
Such a VP cannot be cross-connected. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVplLsPerVcqXmtQueuedCells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.35 |
|
Number of cells received on this VPL and
residing on the per-connection queue. Note that
this value is not valid until the VPL is in an
active cross-connect. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVplLsPerVcQThreshGrp |
.1.3.6.1.4.1.9.10.13.1.1.1.1.36 |
|
The Threshold Group to which the cell-queue for
cells received by this VP are queued. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVplInClp0Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.37 |
|
The total number of cells with the CLP bit clear
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVplInClp1Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.38 |
|
The total number of cells with the CLP bit set
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVplOutClp0Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.39 |
|
The total number of cells with the CLP bit clear
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queueing.
|
| ciscoAtmVplOutClp1Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.40 |
|
The total number of cells with the CLP bit set
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queueing.
|
| ciscoAtmVplCellDrops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.41 |
|
The total number of cells received on this
VPL, but discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVplClp0VcqFullCellDrops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.43 |
|
The total number of cells received on this
VPL with the CLP bit clear, discarded because
the per-VC queue limit is exceeded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVplVcqClpThreshCellDrops |
.1.3.6.1.4.1.9.10.13.1.1.1.1.44 |
|
The total number of cells received on this
VPL, discarded because the discard threshold
(as opposed to the queue-limit) is exceeded
on the per-VC queue, and the CLP bit is set.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVplLsPerVcqTunnelIsHierarchical |
.1.3.6.1.4.1.9.10.13.1.1.1.1.45 |
|
Determines whether this is to be a -Hierarchical- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a Hierarchical VP Tunnel.
Such a VP cannot be cross-connected. This object
is defined on a LS1010 only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVplRxNegTraffDescrIndex |
.1.3.6.1.4.1.9.10.13.1.1.1.1.46 |
|
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the receive
direction of this VPL.
This object is not instantiated if this VPL is not the calling
side of a soft VP, or if there was no traffic negotiation.
|
| ciscoAtmVplTxNegTraffDescrIndex |
.1.3.6.1.4.1.9.10.13.1.1.1.1.47 |
|
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the transmit
direction of this VPL.
This object is not instantiated if this VPL is not the calling
side of a soft VP, or if there was no traffic negotiation.
|
| ciscoAtmVplSwFabOutCells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.48 |
|
The total number of cells transmitted on
this VPL by the Switch Fabric. This object is not
instantiated on systems that do not have support for
collecting such statistics.
|
| ciscoAtmVplSwFabOutClp0Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.49 |
|
The total number of cells with the CLP bit clear
transmitted on this VPL by the Switch Fabric. This object
is not instantiated for a VPL that is a logical interface
(VP Tunnel). This object is not instantiated on systems
that do not have support for collecting such statistics.
|
| ciscoAtmVplSwFabOutClp1Cells |
.1.3.6.1.4.1.9.10.13.1.1.1.1.50 |
|
The total number of cells with the CLP bit set transmitted
on this VPL by the Switch Fabric. This object is not
instantiated for a VPL that is a logical interface
(VP Tunnel). This object is not instantiated on systems
that do not have support for collecting such statistics.
|
| ciscoAtmVplConnName |
.1.3.6.1.4.1.9.10.13.1.1.1.1.51 |
|
A human readable string that identifies this connection.
This object will return a zero-length string if value is
not set.
|
| ciscoAtmVplConnType |
.1.3.6.1.4.1.9.10.13.1.1.1.1.52 |
|
This object represent the PVP Type for this connection.
- local connection within the node
- endToEnd across several nodes
This object serves as an information object for a
management system and has no functional meaning to
the switch.
|
| ciscoAtmVclCastType |
.1.3.6.1.4.1.9.10.13.1.2.1.1.1 |
|
Vcl type is either a point to point connection or point
to multipoint root or leaf.
|
| ciscoAtmVclSpanType |
.1.3.6.1.4.1.9.10.13.1.2.1.1.2 |
|
Vcl span is either a transit one or a terminating one.
|
| ciscoAtmVclConfigType |
.1.3.6.1.4.1.9.10.13.1.2.1.1.3 |
|
Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg.
The half leg can be set to Passive through user configuration only.
|
| ciscoAtmVclRxUpcMode |
.1.3.6.1.4.1.9.10.13.1.2.1.1.4 |
|
Usage Parameter Control opeartion is pass,tag,drop or
local shaping at this connection.
|
| ciscoAtmVclEpdEnable |
.1.3.6.1.4.1.9.10.13.1.2.1.1.5 |
|
Early Packet Discard option used for this VCL.
The use is as follows:
enable(1)
Packet-discard is enabled.
disable(2)
Packet-discard is disabled.
useTrafficDescr(3)
Packet-discard in the receive direction is as specified by
the atmTrafficFrameDiscard value in row corresponding to
atmVclReceiveTrafficDescrIndex. For VCLs of type
spvcInitiator, the packet-discard in the reverse direction
is as specified by the atmTrafficFrameDiscard value in row
corresponding to atmVclTransmitTrafficDescrIndex.
|
| ciscoAtmVclConnState |
.1.3.6.1.4.1.9.10.13.1.2.1.1.6 |
|
The connection state of this VCL.
|
| ciscoAtmVclOamLoopbkTxInterval |
.1.3.6.1.4.1.9.10.13.1.2.1.1.7 |
|
Frequency of OAM loopback cell are generated on this
virtual channel.
|
| ciscoAtmVclOamSegmentLoopback |
.1.3.6.1.4.1.9.10.13.1.2.1.1.8 |
|
Enable segment loopback on this virtual channel.
|
| ciscoAtmVclOamEndLoopback |
.1.3.6.1.4.1.9.10.13.1.2.1.1.9 |
|
Enable end to end loopback on this virtual channel.
|
| ciscoAtmVclOamAisEnable |
.1.3.6.1.4.1.9.10.13.1.2.1.1.10 |
|
Enable Alarm Indication Signal OAM cell generation
if the interafce goes down on a crossconnect virtual
channel.
|
| ciscoAtmVclOamRdiEnable |
.1.3.6.1.4.1.9.10.13.1.2.1.1.11 |
|
Enable Remote Defect Indication OAM cell generation
if an Alarm Indication Signal OAM cell is received.
|
| ciscoAtmVclInstallTime |
.1.3.6.1.4.1.9.10.13.1.2.1.1.12 |
|
The time stamp derived from sysUpTime when this VCL gets
created. The VCL entries are created/deleted as a by-product
of creating and deleting entries in the atmVclTable defined
in RFC1695.
|
| ciscoAtmVclInCells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.13 |
|
The total number of cells received on
this VCL.
|
| ciscoAtmVclOutCells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.14 |
|
The total number of cells transmitted on
this VCL.
|
| ciscoAtmVclCrossIfIndex |
.1.3.6.1.4.1.9.10.13.1.2.1.1.15 |
|
For point to point, this is the cross-connected VCL's
ifIndex of this VCL. For point to multi-point connection,
this will be the root VCL's ifIndex for a leaf VCL entry in
the multicast chain, or it's the 1st leaf VCL for a root
VCL entry. If it's zero, it means it's not cross-connected
yet. Atomically set ciscoAtmVclConnState,
ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and
ciscoAtmVclCrossVci will create or delete a cross
connection to crossed half leg of this
ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and
ciscoAtmVclCrossVci for p2p PVC, or add or drop a multicast
connection to/from the root of this ciscoAtmVclCrossIfindex,
ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci on the multicast
chain for p2mp PVC.
|
| ciscoAtmVclCrossVpi |
.1.3.6.1.4.1.9.10.13.1.2.1.1.16 |
|
This specifies the VPI value of the VCL to which this
VCL is cross-connected. For point to multi-point
connection, this is the root VCL's VPI for the leaf entry.
Similarly it is the 1st leaf's VPI value for the root entry.
|
| ciscoAtmVclCrossVci |
.1.3.6.1.4.1.9.10.13.1.2.1.1.17 |
|
This specifies the VCI value of the VCL to which this
VCL is cross-connected. For point to multi-point
connection, this is the root VCL's VCI for the leaf
entry. Similarly it is the 1st leaf's VCI value for
the root entry.
|
| ciscoAtmVclNextLeafIfIndex |
.1.3.6.1.4.1.9.10.13.1.2.1.1.18 |
|
For point to point, this is zero i.e. not used.
For point to multi-point connection, this will be
the next leaf VCL's ifIndex on the multicast chain.
This will be 0 if this is the root VCL entry.
If it's zero for a leaf VCL, it means this is the
last leaf.
|
| ciscoAtmVclNextLeafVpi |
.1.3.6.1.4.1.9.10.13.1.2.1.1.19 |
|
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VCL's VPI on the multicast
chain.
|
| ciscoAtmVclNextLeafVci |
.1.3.6.1.4.1.9.10.13.1.2.1.1.20 |
|
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VCL's VCI on the multicast
chain.
|
| ciscoAtmVclAalEncapFlag |
.1.3.6.1.4.1.9.10.13.1.2.1.1.21 |
|
Encapsulation type for terminating VC.
|
| ciscoAtmVclAalEncapProtocol |
.1.3.6.1.4.1.9.10.13.1.2.1.1.22 |
|
Protocol for terminating VC if EncapFlag is aal5Mux.
|
| ciscoAtmVclAalUserVcType |
.1.3.6.1.4.1.9.10.13.1.2.1.1.23 |
|
Following is the list of user virtual circuit types in
case aal5Lane encapusation on this virtual channel.
boxConfigure -- The shared Server/Client end of a
Configure VCC
busForward -- The BUS end of the Data Forward VCC
busSend -- The BUS end of the Data Send VCC
clientConfigure -- The LE Client end of the Configure
Direct VCC
clientData -- One end of the Data Direct VCC
clientDirect -- The LE Client end of the Control
Direct VCC
clientDistribute -- The LE Client end of the Control
Distribute VCC
clientForward -- The LE Client end of the Multicast
Forward VCC
clientSend -- The LE Client end of the Multicast
Send VCC
configure -- The Config Server end of any Configure VCC
serverConfigure -- The LE Server end of the Configure VCC
serverDirect -- The LE Server end of the Control
Direct VCC.
|
| ciscoAtmVclAtmInArpInterval |
.1.3.6.1.4.1.9.10.13.1.2.1.1.24 |
|
Time interval in minutes to send InArp on a PVC for
IP over ATM. 0 will disable the InArp for this pvc.
|
| ciscoAtmVclRemoteAddr |
.1.3.6.1.4.1.9.10.13.1.2.1.1.25 |
|
Soft PVC target address if this is the calling side
Soft PVC source address if this is called side.
Atomically set ConnState, RemoteAddr, RemoteVpi
and RemoteVci will create or delete a soft PVC.
Atomically set ConnState, RemoteAddr without RemoteVpi,
Remote Vci will also create or delete a soft PVC but let
target switch assign the vpi and vci.
|
| ciscoAtmVclRemoteVpi |
.1.3.6.1.4.1.9.10.13.1.2.1.1.26 |
|
Soft PVC target VPI in calling side. 0 in called side.
|
| ciscoAtmVclRemoteVci |
.1.3.6.1.4.1.9.10.13.1.2.1.1.27 |
|
Soft PVC target VCI in calling side. 0 in called side.
|
| ciscoAtmVclLocation |
.1.3.6.1.4.1.9.10.13.1.2.1.1.28 |
|
Indicate calling or called side of a soft PVC.
If ciscoAtmVclConfigType is not soft then
ciscoAtmVclLocation value should be ignored.
|
| ciscoAtmVclSlowRetryIntv |
.1.3.6.1.4.1.9.10.13.1.2.1.1.29 |
|
Soft PVC slow retry interval in seconds.
|
| ciscoAtmVclNumAttempts |
.1.3.6.1.4.1.9.10.13.1.2.1.1.30 |
|
Number of retries made to install this soft PVC
connection. If ciscoAtmVclConfigType is not soft then
ciscoAtmVclNumAttempts value should be ignored.
|
| ciscoAtmVclLastReleaseCause |
.1.3.6.1.4.1.9.10.13.1.2.1.1.31 |
|
Value of the Cause field of the Cause
Information Element in the last Release
Signalling message received for this SPVC.
Indicates the reason for the Release.
ciscoAtmVclConfigType is not soft then
ciscoAtmVclLastReleaseCause value should be
ignored.
|
| ciscoAtmVclUpcViolations |
.1.3.6.1.4.1.9.10.13.1.2.1.1.32 |
|
The total number of nonconforming cells detected
by Usage Parameter Control (UPC) for cells received
on this VCL.
On LS1010 systems, this counter is valid only on those
equipped with the Feature Card - Per Flow Queueing.
|
| ciscoAtmVclEpdTpdCellDrops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.33 |
|
Never implemented.
|
| ciscoAtmVclEpdTpdPacketDrops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.34 |
|
The total number of EPD/TPD packet drops of
packets received on this VCL.
This counter is valid only:
- if EPD is enabled on this VCL.
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queueing.
|
| ciscoAtmVclEpdTpdPacketsIn |
.1.3.6.1.4.1.9.10.13.1.2.1.1.35 |
|
The total number of packets received in their
entirety on this VPL.
This counter is valid only:
- if EPD is enabled on this VCL.
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queueing.
|
| ciscoAtmVclClp1Drops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.37 |
|
Never implemented.
|
| ciscoAtmVclDefaultRxUpcTolerance |
.1.3.6.1.4.1.9.10.13.1.2.1.1.38 |
|
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum
Burst Size for VBR connectons) requested for Usage
Parameter Control is not explicitly specified in VCL creation,
this object contains the default that is used.If tolerance
is explicitly specified in VCL creation, it can be found in
the Traffic Table row specified by atmVclReceiveTrafficDescrIndex,
and the value of this object is -1.
|
| ciscoAtmVclDefaultRxUpcVbrCdvt |
.1.3.6.1.4.1.9.10.13.1.2.1.1.39 |
|
If the Cell Delay Variation Tolerance (CDVT) requested for
Usage Parameter Control for a VBR connection is not explicitly
specified in VCL creation, this object contains the default
that is used. If CDVT is explicitly specified in VCL creation,
it can be found in the Traffic Table row specified by
atmVclReceiveTrafficDescrIndex, and the value of this object
is -1.
|
| ciscoAtmVclLsPerVcqWrrWeight |
.1.3.6.1.4.1.9.10.13.1.2.1.1.40 |
|
Configure the weighting specified for a VC half-leg
within a service class to make the scheduling decision
among other active VCLs in the service class. This
is for transmit on the VCL on the interface. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVclLsPerVcqXmtQueuedCells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.41 |
|
Number of cells received on this VCL and
residing on the per-connection queue. Note that
this value is not valid until the VCL is in an
active cross-connect. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVclLsPerVcQThreshGrp |
.1.3.6.1.4.1.9.10.13.1.2.1.1.42 |
|
The Threshold Group to which the cell-queue
for cells received by this VC are queued.
Note that this value is not valid until the
VCL is in an active cross-connect. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
|
| ciscoAtmVclInClp0Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.43 |
|
The total number of cells with the CLP bit clear
received on this VCL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclInClp1Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.44 |
|
The total number of cells with the CLP bit set
received on this VCL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclOutClp0Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.45 |
|
The total number of cells with the CLP bit clear
transmitted on this VCL.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclOutClp1Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.46 |
|
The total number of cells with the CLP bit set
transmitted on this VCL.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclCellDrops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.47 |
|
The total number of cells received on this
VCL, but discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclClp0VcqFullCellDrops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.48 |
|
The total number of cells received on this
VCL with the CLP bit clear, discarded because
the per-VC queue limit is exceeded.
This counter is valid only:
- if EPD is disabled on the VCL.
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclVcqClpThreshCellDrops |
.1.3.6.1.4.1.9.10.13.1.2.1.1.49 |
|
The total number of cells received on this
VCL, discarded because the discard threshold
(as opposed to the queue-limit) is exceeded
on the per-VC queue, and the CLP bit is set.
This counter is valid only:
- if EPD is disabled on the VCL.
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
|
| ciscoAtmVclRxNegTraffDescrIndex |
.1.3.6.1.4.1.9.10.13.1.2.1.1.50 |
|
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the receive
direction of this VCL.
This object is not instantiated if this VCL is not the calling
side of a soft VC, or if there was no traffic negotiation.
|
| ciscoAtmVclTxNegTraffDescrIndex |
.1.3.6.1.4.1.9.10.13.1.2.1.1.51 |
|
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the transmit
direction of this VCL.
This object is not instantiated if this VCL is not the calling
side of a soft VC, or if there was no traffic negotiation.
|
| ciscoAtmVclSwFabOutCells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.52 |
|
The total number of cells transmitted on
this VCL by the Switch Fabric. This object is not
instantiated on systems that do not have support for
collecting such statistics.
|
| ciscoAtmVclSwFabOutClp0Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.53 |
|
The total number of cells with the CLP bit clear
transmitted on this VCL by the Switch Fabric.
This object is not instantiated on systems
that do not have support for collecting such
statistics.
|
| ciscoAtmVclSwFabOutClp1Cells |
.1.3.6.1.4.1.9.10.13.1.2.1.1.54 |
|
The total number of cells with the CLP bit set
transmitted on this VCL by the Switch Fabric.
This object is not instantiated on systems that
do not have support for collecting such statistics.
|
| ciscoAtmVclConnName |
.1.3.6.1.4.1.9.10.13.1.2.1.1.55 |
|
A human readable string that identifies this connection.
This object will return a zero-length string if value is
not set.
|
| ciscoAtmVclConnType |
.1.3.6.1.4.1.9.10.13.1.2.1.1.56 |
|
This object represent the PVC Type for this connection.
- local connection within the node
- endToEnd across several nodes.
This object serves as an information object for a
management system and has no functional meaning to
the switch.
|
| ciscoAtmSvpAddr |
.1.3.6.1.4.1.9.10.13.1.3.1.1.1 |
|
It depends on the direction.This could be p2pCallingSide
address on a called side VPL, or p2pCalledSide address on a
calling side VPL or p2mpRoot address on a p2mp leaf side
VPL or p2mpLeaf address on a p2mp root side VPL.
|
| ciscoAtmSvpVpi |
.1.3.6.1.4.1.9.10.13.1.3.1.1.2 |
|
This SVP's VPI value on this interface.
|
| ciscoAtmSvpDirection |
.1.3.6.1.4.1.9.10.13.1.3.1.1.3 |
|
Indicate whether this VPL is calling side, called side,
root or leaf for this address.
|
| ciscoAtmSvcAddr |
.1.3.6.1.4.1.9.10.13.1.4.1.1.1 |
|
It depends on the direction.This could be p2pCallingSide
address on a called side VCL, or p2pCalledSide address on a
calling side VCL or p2mpRoot address on a p2mp leaf side VCL
or p2mpLeaf address on a p2mp root side VCL.
|
| ciscoAtmSvcVpi |
.1.3.6.1.4.1.9.10.13.1.4.1.1.2 |
|
This SVC's VPI value on this interface.
|
| ciscoAtmSvcVci |
.1.3.6.1.4.1.9.10.13.1.4.1.1.3 |
|
This SVC's VCI value on this interface.
|
| ciscoAtmSvcDirection |
.1.3.6.1.4.1.9.10.13.1.4.1.1.4 |
|
Indicate whether this VCL is calling side, called side,
root or leaf for this address.
|
| ciscoAtmSnoopVcSnoopedIfIndex |
.1.3.6.1.4.1.9.10.13.1.5.1.1.1 |
|
This specifies the ifIndex of the snooped interface.
|
| ciscoAtmSnoopVcSnoopedVpi |
.1.3.6.1.4.1.9.10.13.1.5.1.1.2 |
|
This specifies the VPI value of the snooped connection endpoint.
|
| ciscoAtmSnoopVcSnoopedVci |
.1.3.6.1.4.1.9.10.13.1.5.1.1.3 |
|
This specifies the VCI value of the snooped connection endpoint.
|
| ciscoAtmSnoopVcDir |
.1.3.6.1.4.1.9.10.13.1.5.1.1.4 |
|
This specifies the traffic direction at the snooped connection
endpoint.
|
| ciscoAtmSnoopVcState |
.1.3.6.1.4.1.9.10.13.1.5.1.1.5 |
|
The connection state of this Snooping connetion.
|
| ciscoAtmSnoopVcRowStatus |
.1.3.6.1.4.1.9.10.13.1.5.1.1.6 |
|
This object is used to create a new row or delete an existing row
in this table. This gives the way to configure one-shot per-vc
snooping connection
|
| ciscoAtmSnoopVpSnoopedIfIndex |
.1.3.6.1.4.1.9.10.13.1.6.1.1.1 |
|
This specifies the ifIndex of the snooped interface.
|
| ciscoAtmSnoopVpSnoopedVpi |
.1.3.6.1.4.1.9.10.13.1.6.1.1.2 |
|
This specifies the VPI value of the snooped connection endpoint.
|
| ciscoAtmSnoopVpDir |
.1.3.6.1.4.1.9.10.13.1.6.1.1.3 |
|
This specifies the traffic direction at the snooped connection
endpoint.
|
| ciscoAtmSnoopVpState |
.1.3.6.1.4.1.9.10.13.1.6.1.1.4 |
|
The connection state of this Snooping connection .
|
| ciscoAtmSnoopVpRowStatus |
.1.3.6.1.4.1.9.10.13.1.6.1.1.5 |
|
This object is used to create a new row or delete an existing row
in this table. This gives the way to configure one-shot per-vp
snooping connection
|
