| ciscoAtmIfPhysStatus |
.1.3.6.1.4.1.9.9.45.1.1.1.1 |
|
The status of the physical interface. The value of this
object is only valid when the interface's ifAdminStatus
has the value 'up'. Note that some of the enumerated
values are specific to a particular physical layer.
|
| ciscoAtmIfPhysSectionParityErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.2 |
|
The number of B1 (BIP) errors on the physical interface.
This object is only present for SONET interfaces.
|
| ciscoAtmIfPhysLineParityErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.3 |
|
The number of B2 (BIP) errors on the physical interface.
This object is only present for SONET interfaces.
|
| ciscoAtmIfPhysPathParityErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.4 |
|
The number of B3 (BIP) errors on the physical interface.
This object is only present for SONET interfaces.
|
| ciscoAtmIfPhysLcvErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.5 |
|
The number of Line Code Violation errors on the physical
interface. This object is only present for DS3/E3/DS1/E1
interfaces.
|
| ciscoAtmIfPhysCBitParityErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.6 |
|
The number of C-bit parity violations on the physical
interface. This object is only present for DS3
interfaces.
|
| ciscoAtmIfPhysPBitParityErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.7 |
|
The number of P-bit parity violations or E3 G.832 BIP-8
errors on the physical
interface. This object is present only for DS3/E3
interfaces.
|
| ciscoAtmIfPhysPlcpBipViolations |
.1.3.6.1.4.1.9.9.45.1.1.1.8 |
|
The number of PLCP BIP violations on the physical
interface. This object is only present for DS3/E3/DS1/E1
interfaces.
|
| ciscoAtmIfPhysLineFebeErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.9 |
|
The number of Z2 (Line FEBE) errors on the physical interface.
This object is only present for SONET interfaces.
|
| ciscoAtmIfPhysPathFebeErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.10 |
|
The number of G1 (Path FEBE) errors on the physical interface.
This object is only present for SONET interfaces.
|
| ciscoAtmIfPhysCellPayloadScrambling |
.1.3.6.1.4.1.9.9.45.1.1.1.11 |
|
The status of whether cell payload scrambling is
enabled or disabled on the physical interface.
|
| ciscoAtmIfPhysStsStreamScrambling |
.1.3.6.1.4.1.9.9.45.1.1.1.12 |
|
The status of whether STS-stream scrambling is
enabled or disabled on the physical interface.
|
| ciscoAtmIfPhysFramingMode |
.1.3.6.1.4.1.9.9.45.1.1.1.13 |
|
The framing format present on the physical interface.
'sonet' indicates sts-3c or sts-12c format and applies only
to OC-3 and OC-12 type interfaces, respectively.
'sdh' indicates stm1 or stm4 format and applies only to
OC-3 and OC-12 type interfaces, respectively.
'ds3m23adm' indicates M23 ADM mode and applies only to DS3
type interfaces.
'ds3m23plcp' indicates M23 PLCP mode and applies only to DS3
type interfaces.
'ds3cbitadm' indicates C-BIT ADM mode and applies only to DS3
type interfaces.
'ds3cbitplcp' indicates C-BIT PLCP mode and applies only to DS3
type interfaces.
'e3g832adm' indicates G.832 ADM mode and applies only to E3
type interfaces.
'e3g751adm' indicates G.751 ADM mode and applies only to E3
type interfaces.
'e3g751plcp' indicates G.751 PLCP mode and applies only to E3
type interfaces.
'ds1sfadm' indicates DS1 SF ADM mode and applies only to DS1
type interfaces.
'ds1esfadm' indicates DS1 ESF ADM mode and applies only to DS1
type interfaces.
'ds1sfplcp' indicates DS1 SF PLCP mode and applies only to DS1
type interfaces.
'ds1esfplcp' indicates DS1 ESF PLCP mode and applies only to DS1
type interfaces.
'e1adm' indicates E1 ADM mode and applies only to E1
type interfaces.
'e1plcp' indicates E1 PLCP mode and applies only to E1
type interfaces.
'e1crcadm' indicates E1 CRC-4 ADM mode and applies only to E1
type interfaces.
'e1crcplcp' indicates E1 CRC-4 PLCP mode and applies only to E1
type interfaces.
|
| ciscoAtmIfPhysLoopbackConfig |
.1.3.6.1.4.1.9.9.45.1.1.1.14 |
|
The loopback configured on the physical interface:
'noLoop' indicates no loopback is present.
'diagnosticLoop' indicates transmit data stream is
looped to the receive direction.
'lineLoop' indicates receive data stream is
looped to the transmit direction.
'otherLoop' indicates loopbacks that are not defined here.
|
| ciscoAtmIfPhysLineBuildOut |
.1.3.6.1.4.1.9.9.45.1.1.1.15 |
|
The line buildout configured on the transmit signal:
'e3AllCables' applies to all cables of E3 physical
interfaces.
'ds3CablesUnder225' applies to cables under 225 feet of
DS3 physical interfaces.
'ds3CablesOver225' applies to cables over 225 feet of
DS3 physical interfaces.
'ds1Cables0To110' applies to cables 0 to 110 feet of
DS1 physical interfaces.
'ds1Cables110To220' applies to cables 110 to 220 feet of
DS1 physical interfaces.
'ds1Cables220To330' applies to cables 220 to 330 feet of
DS1 physical interfaces.
'ds1Cables330To440' applies to cables 330 to 440 feet of
DS1 physical interfaces.
'ds1Cables440To550' applies to cables 440 to 550 feet of
DS1 physical interfaces.
'ds1Cables550To660' applies to cables 550 to 660 feet of
DS1 physical interfaces.
'ds1CablesOver600' applies to cables over 600 feet of
DS1 physical interfaces.
'e1AllCables' applies to all cables of
E1 physical interfaces.
|
| ciscoAtmIfPhysTransmitClockSource |
.1.3.6.1.4.1.9.9.45.1.1.1.16 |
|
The source of the tranmit clock:
'loopTiming' indicates that the recovered receive
clock is used as the transmit clock.
'freeRunning' indicates that a local clock source is
used.
'networkDerived' indicates that recovered receive
clock from another interface is used as the transmit
clock source.
|
| ciscoAtmIfPhysClockSourcePriority |
.1.3.6.1.4.1.9.9.45.1.1.1.17 |
|
The priority of this interface if configured as
a network clock source.
'notConfigured' indicates this is not configured as
a network clock source.
|
| ciscoAtmIfPhysClockSourceStatus |
.1.3.6.1.4.1.9.9.45.1.1.1.18 |
|
The network clock source status of this interface:
'notSelected' indicates this is not selected as the
network clock source.
'selected' indicates this is selected as the
network clock source.
|
| ciscoAtmIfPhysDS1BitErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.19 |
|
The number of bit errors (CRC-6 error in ESF mode and
framing bit error in SF mode) on the physical
interface. This object is only present for DS1
interfaces.
|
| ciscoAtmIfPhysE1CrcErrors |
.1.3.6.1.4.1.9.9.45.1.1.1.20 |
|
The number of CRC errors (in CRC-4 mode) on the physical
interface. This object is only present for E1
interfaces.
|
| ciscoAtmIfPhysLineCode |
.1.3.6.1.4.1.9.9.45.1.1.1.21 |
|
The line coding present on the physical interface This object
is only present for DS1/E1 interfaces.
'ami' indicates alternate mark inversion (AMI) line code
on the DS1/E1 interface.
'b8zs' indicates B8ZS line code on the physical interface and
applies only to DS1 interfaces.
'hdb3' indicates HDB3 line code on the physical interface and
applies only to E1 interfaces.
|
| ciscoAtmIfPhysMIBCommonGroup |
.1.3.6.1.4.1.9.9.45.3.2.1 |
|
A collection of objects common to all ATM physical
layer interfaces.
|
| ciscoAtmIfPhysMIBCommonGroup2 |
.1.3.6.1.4.1.9.9.45.3.2.4 |
|
Additional collection of objects common to all ATM physical
layer interfaces.
|
| ciscoAtmIfPhysMIBSonetGroup |
.1.3.6.1.4.1.9.9.45.3.2.2 |
|
A collection of objects for ATM SONET interfaces.
|
| ciscoAtmIfPhysMIBSonetGroup2 |
.1.3.6.1.4.1.9.9.45.3.2.5 |
|
Additional collection of objects for ATM SONET interfaces.
|
| ciscoAtmIfPhysMIBDs3E3Group |
.1.3.6.1.4.1.9.9.45.3.2.3 |
|
A collection of objects for ATM DS3/E3 interfaces.
|
| ciscoAtmIfPhysMIBDs3Group |
.1.3.6.1.4.1.9.9.45.3.2.6 |
|
Collection of objects for ATM DS3 interfaces.
|
| ciscoAtmIfPhysMIBDs1E1Group |
.1.3.6.1.4.1.9.9.45.3.2.7 |
|
A collection of objects for ATM DS1/E1 interfaces.
|
| ciscoAtmIfPhysMIBDs1Group |
.1.3.6.1.4.1.9.9.45.3.2.8 |
|
A collection of objects for ATM DS1 interfaces.
|
| ciscoAtmIfPhysMIBE1Group |
.1.3.6.1.4.1.9.9.45.3.2.9 |
|
A collection of objects for ATM E1 interfaces.
|
