CISCO-ATM-QOS-MIB device MIB details by Cisco
CISCO-ATM-QOS-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-ATM-QOS-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-ATM-QOS-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ***************************************************************** -- CISCO-ATM-QOS-MIB.my: Cisco ATM QoS MIB file -- -- June 2002, Danny Lee -- -- Copyright (c) 2002 by Cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-ATM-QOS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB atmVplVpi, atmVclVpi, atmVclVci FROM ATM-MIB AtmServiceCategory FROM ATM-FORUM-TC-MIB ciscoMgmt FROM CISCO-SMI; ciscoAtmQosMIB MODULE-IDENTITY LAST-UPDATED "200206100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 SA Tel: +1 800 553-NETS Email: cs-atm@cisco.com" DESCRIPTION "The MIB is created to provide ATM QoS information in these areas: 1. Traffic shaping on a per-VC basis 2. Traffic shaping on a per-VP basis 3. Per-VC queuing/buffering Although the initial requirements of the MIB are driven to support the GSR TAZ line card, CISCO-ATM-QOS-MIB is designed as a generic MIB to support ATM interfaces across all platforms. Here are the tables defined in this MIB: ciscoAtmQosVccTable - to provide information on traffic shaping on a per-VC basis. ciscoAtmQosVpcTable - to provide information on traffic shaping on a per-VP basis. ciscoAtmQosVcQueuingTable ciscoAtmQosVcQueuingClassTable - to provide information on per-VC queuing/buffering." REVISION "200206100000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 279 } ciscoAtmQosMIBNotifs OBJECT IDENTIFIER ::= { ciscoAtmQosMIB 0 } ciscoAtmQosMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmQosMIB 1 } ciscoAtmQosMIBConform OBJECT IDENTIFIER ::= { ciscoAtmQosMIB 2 } caqVccParams OBJECT IDENTIFIER ::= { ciscoAtmQosMIBObjects 1 } caqVpcParams OBJECT IDENTIFIER ::= { ciscoAtmQosMIBObjects 2 } caqQueuingParams OBJECT IDENTIFIER ::= { ciscoAtmQosMIBObjects 3 } -- -- -- Beginning Textual Convention Definitions VcParamConfigLocation ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The configuration source of a vc parameter: 1 - Not configured - using default 2 - Configured on vc directly 3 - VC-class configured on vc 4 - VC-class configured on sub-interface 5 - VC-class configured on main-interface. " SYNTAX INTEGER { configDefault(1), configVcDirect(2), configVcClass(3), configVcClassSubInterface(4), configVcClassInterface(5) } VpState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "States of virtual path: 1 - Inactive 2 - Active " SYNTAX INTEGER { vpStateInactive(1), vpStateActive(2) } -- Ending Textual Convention Definitions -- -- -- -- -- Per-VC Traffic shaping parameters -- (Beginning of caqVccTable) caqVccParamsTable OBJECT-TYPE SYNTAX SEQUENCE OF CaqVccParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is defined to provide QoS information for each active ATM VC existing on the interface." ::= { caqVccParams 1 } caqVccParamsEntry OBJECT-TYPE SYNTAX CaqVccParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This list contains the ATM QoS parameters provided by ciscoAtmQosVccEntry." INDEX { ifIndex, atmVclVpi, atmVclVci } ::= { caqVccParamsTable 1 } CaqVccParamsEntry ::= SEQUENCE { caqVccParamsType AtmServiceCategory, caqVccParamsPcrIn0 Unsigned32, caqVccParamsPcrIn01 Unsigned32, caqVccParamsPcrOut0 Unsigned32, caqVccParamsPcrOut01 Unsigned32, caqVccParamsScrIn0 Unsigned32, caqVccParamsScrIn01 Unsigned32, caqVccParamsScrOut0 Unsigned32, caqVccParamsScrOut01 Unsigned32, caqVccParamsBcsIn0 Unsigned32, caqVccParamsBcsIn01 Unsigned32, caqVccParamsBcsOut0 Unsigned32, caqVccParamsBcsOut01 Unsigned32, caqVccParamsInheritLevel VcParamConfigLocation, caqVccParamsMcrIn Unsigned32, caqVccParamsMcrOut Unsigned32, caqVccParamsInvRdf Unsigned32, caqVccParamsInvRif Unsigned32, caqVccParamsRfl VcParamConfigLocation, caqVccParamsCdv Unsigned32, caqVccParamsCdvt Unsigned32, caqVccParamsIcr Unsigned32, caqVccParamsTbe Unsigned32, caqVccParamsFrtt Unsigned32, caqVccParamsNrm Unsigned32, caqVccParamsInvTrm Unsigned32, caqVccParamsInvCdf Unsigned32, caqVccParamsAdtf Unsigned32 } caqVccParamsType OBJECT-TYPE SYNTAX AtmServiceCategory MAX-ACCESS read-write STATUS current DESCRIPTION "The service category of this virtual circuit connection." ::= { caqVccParamsEntry 1 } caqVccParamsPcrIn0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 2 } caqVccParamsPcrIn01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of OAM F5 end to end loopback cells sent through the VCC." ::= { caqVccParamsEntry 3 } caqVccParamsPcrOut0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 4 } caqVccParamsPcrOut01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 1 (clp01)." ::= { caqVccParamsEntry 5 } caqVccParamsScrIn0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 6 } caqVccParamsScrIn01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01)." ::= { caqVccParamsEntry 7 } caqVccParamsScrOut0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 8 } caqVccParamsScrOut01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01)." ::= { caqVccParamsEntry 9 } caqVccParamsBcsIn0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 10 } caqVccParamsBcsIn01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01)." ::= { caqVccParamsEntry 11 } caqVccParamsBcsOut0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0)." ::= { caqVccParamsEntry 12 } caqVccParamsBcsOut01 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01)." ::= { caqVccParamsEntry 13 } caqVccParamsInheritLevel OBJECT-TYPE SYNTAX VcParamConfigLocation MAX-ACCESS read-only STATUS current DESCRIPTION "The source of configuration for peak cell rate." ::= { caqVccParamsEntry 14 } caqVccParamsMcrIn OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Input Minimum Cell Rate (MCR) in kbps for connection with VBR-nrt or ABR type of QoS." ::= { caqVccParamsEntry 15 } caqVccParamsMcrOut OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Output Minimum Cell Rate (MCR) in kbps for connection with VBR-nrt or ABR type of QoS." ::= { caqVccParamsEntry 16 } caqVccParamsInvRdf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Inverse of rate decrease factor." ::= { caqVccParamsEntry 17 } caqVccParamsInvRif OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Inverse of rate increase factor." ::= { caqVccParamsEntry 18 } caqVccParamsRfl OBJECT-TYPE SYNTAX VcParamConfigLocation MAX-ACCESS read-only STATUS current DESCRIPTION "The source of configuration for rate factor." ::= { caqVccParamsEntry 19 } caqVccParamsCdv OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cell delay variation." ::= { caqVccParamsEntry 20 } caqVccParamsCdvt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Cell delay variation tolerance." ::= { caqVccParamsEntry 21 } caqVccParamsIcr OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Initial cell rate." ::= { caqVccParamsEntry 22 } caqVccParamsTbe OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Transient buffer exposure." ::= { caqVccParamsEntry 23 } caqVccParamsFrtt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Fixed round-trip time." ::= { caqVccParamsEntry 24 } caqVccParamsNrm OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of tx cells for each forward rm cell." ::= { caqVccParamsEntry 25 } caqVccParamsInvTrm OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum time between forward rm cells." ::= { caqVccParamsEntry 26 } caqVccParamsInvCdf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Inverse of cutoff decrease factor." ::= { caqVccParamsEntry 27 } caqVccParamsAdtf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Allowed cell rate decrease time factor." ::= { caqVccParamsEntry 28 } -- (End of caqVccParamsTable) -- -- -- -- -- Per-VP traffic shaping parameters. -- (Beginning of caqVpcParamsTable) caqVpcParamsTable OBJECT-TYPE SYNTAX SEQUENCE OF CaqVpcParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is defined to provide QoS information for each active ATM VP existing on the interface." ::= { caqVpcParams 1 } caqVpcParamsEntry OBJECT-TYPE SYNTAX CaqVpcParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This list contains the ATM QoS parameters provided by ciscoAtmQosVpcEntry." INDEX { ifIndex, atmVplVpi } ::= { caqVpcParamsTable 1 } CaqVpcParamsEntry ::= SEQUENCE { caqVpcParamsVpState VpState, caqVpcParamsPeakRate Unsigned32, caqVpcParamsCesRate Unsigned32, caqVpcParamsDataVcCount Integer32, caqVpcParamsCesVcCount Integer32, caqVpcParamsVcdF4Seg Integer32, caqVpcParamsVcdF4Ete Integer32, caqVpcParamsScr Unsigned32, caqVpcParamsMbs Unsigned32, caqVpcParamsAvailBw Unsigned32 } caqVpcParamsVpState OBJECT-TYPE SYNTAX VpState MAX-ACCESS read-only STATUS current DESCRIPTION "VP state of the current permanent virtual path." ::= { caqVpcParamsEntry 1 } caqVpcParamsPeakRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum rate in kbps at which the associated permanent virtual path can transmit data." ::= { caqVpcParamsEntry 2 } caqVpcParamsCesRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum rate in kbps at which CES VCs can transmit data with the associated permanent virtual path." ::= { caqVpcParamsEntry 3 } caqVpcParamsDataVcCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of data VCs currently associated with the permanent virtual path." ::= { caqVpcParamsEntry 4 } caqVpcParamsCesVcCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CES VCs currently associated with the permanent virtual path." ::= { caqVpcParamsEntry 5 } caqVpcParamsVcdF4Seg OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Vcd for F4 OAM segment processing." ::= { caqVpcParamsEntry 6 } caqVpcParamsVcdF4Ete OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Vcd for F4 OAM end to end processing." ::= { caqVpcParamsEntry 7 } caqVpcParamsScr OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sustained cell rate associated with the PVP." ::= { caqVpcParamsEntry 8 } caqVpcParamsMbs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum burst size associated with the PVP." ::= { caqVpcParamsEntry 9 } caqVpcParamsAvailBw OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Bandwidth in Kbps currently currently available on this PVP." ::= { caqVpcParamsEntry 10 } -- End of caqVpcParamsTable -- -- -- -- -- Per-VC queuing parameters -- Beginning of caqQueuingParamsTable caqQueuingParamsTable OBJECT-TYPE SYNTAX SEQUENCE OF CaqQueuingParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides queuing related information for a VC existing on an ATM interface." ::= { caqQueuingParams 1 } caqQueuingParamsEntry OBJECT-TYPE SYNTAX CaqQueuingParamsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as an entry in caqQueuingParamsTable." INDEX { ifIndex, atmVclVpi, atmVclVci } ::= { caqQueuingParamsTable 1 } CaqQueuingParamsEntry ::= SEQUENCE { caqQueuingParamsMeanQDepth Unsigned32 } caqQueuingParamsMeanQDepth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Mean Queue Depth associated with the vc. This value is calculated based on the actual queue depth on the interface and the exponential weighting constant." ::= { caqQueuingParamsEntry 1 } -- (End of caqQueuingParamsTable) -- -- -- -- -- (Beginning of caqQueuingParamsClassTable) caqQueuingParamsClassTable OBJECT-TYPE SYNTAX SEQUENCE OF CaqQueuingParamsClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides queuing information for all queuing classes associating with a VC." ::= { caqQueuingParams 2 } caqQueuingParamsClassEntry OBJECT-TYPE SYNTAX CaqQueuingParamsClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as an entry in ciscoAtmQosVcQueuingClassTable to provide queuing information of a specific class." INDEX { ifIndex, atmVclVpi, atmVclVci, caqQueuingParamsClassIndex } ::= { caqQueuingParamsClassTable 1 } CaqQueuingParamsClassEntry ::= SEQUENCE { caqQueuingParamsClassIndex Integer32, caqQueuingParamsClassRandDrp Unsigned32, caqQueuingParamsClassTailDrp Unsigned32, caqQueuingParamsClassMinThre Unsigned32, caqQueuingParamsClassMaxThre Unsigned32, caqQueuingParamsClassMrkProb Unsigned32 } caqQueuingParamsClassIndex OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A class index, which associates with an IP precedence (0 to 8), is defined to reference individual caqQueuingParamsClassEntry." ::= { caqQueuingParamsClassEntry 1 } caqQueuingParamsClassRandDrp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets dropped when Mean Queue Length is between Minimum Threshold and Maximum Threshold range." ::= { caqQueuingParamsClassEntry 2 } caqQueuingParamsClassTailDrp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets dropped because the Mean Queue Depth exceeds the Maximum Threshold value." ::= { caqQueuingParamsClassEntry 3 } caqQueuingParamsClassMinThre OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum Threshold value in kbps." ::= { caqQueuingParamsClassEntry 4 } caqQueuingParamsClassMaxThre OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Threshold value in kbps." ::= { caqQueuingParamsClassEntry 5 } caqQueuingParamsClassMrkProb OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Mark probability denominator. This is the value used in the calculation of a packet being dropped when the average queue size is between the minimum threshold and the maximum threshold." ::= { caqQueuingParamsClassEntry 6 } -- (End of caqQueuingParamsClassTable) -- -- -- Conformance Information ciscoAtmQosMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmQosMIBConform 1 } ciscoAtmQosMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmQosMIBConform 2 } -- Compliance Statement ciscoAtmQosMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement this Cisco ATM QoS MIB." MODULE -- this module MANDATORY-GROUPS { ciscoAtmQosVccGroup, ciscoAtmQosVpcGroup, ciscoAtmQosVcQueuingGroup } OBJECT caqVccParamsType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsPcrIn0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsPcrIn01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsPcrOut0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsPcrOut01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsScrIn0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsScrIn01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsScrOut0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsScrOut01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsBcsIn0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsBcsIn01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsBcsOut0 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsBcsOut01 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsMcrIn MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsMcrOut MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsInvRdf MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsInvRif MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsCdvt MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsIcr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsTbe MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsFrtt MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsNrm MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT caqVccParamsInvTrm MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP ciscoAtmQosVccAddon1Group DESCRIPTION "This group is optional." GROUP ciscoAtmQosVpcAddon1Group DESCRIPTION "This group is optional." ::= { ciscoAtmQosMIBCompliances 1 } -- units of conformance: ciscoAtmQosVccGroup OBJECT-GROUP OBJECTS { caqVccParamsType, caqVccParamsPcrIn0, caqVccParamsPcrIn01, caqVccParamsPcrOut0, caqVccParamsPcrOut01, caqVccParamsScrIn0, caqVccParamsScrIn01, caqVccParamsScrOut0, caqVccParamsScrOut01, caqVccParamsBcsIn0, caqVccParamsBcsIn01, caqVccParamsBcsOut0, caqVccParamsBcsOut01, caqVccParamsInheritLevel, caqVccParamsMcrIn, caqVccParamsMcrOut, caqVccParamsInvRdf, caqVccParamsInvRif, caqVccParamsRfl } STATUS current DESCRIPTION "A collection of objects providing per-VC ATM QoS related info." ::= { ciscoAtmQosMIBGroups 1 } ciscoAtmQosVccAddon1Group OBJECT-GROUP OBJECTS { caqVccParamsCdv, caqVccParamsCdvt, caqVccParamsIcr, caqVccParamsTbe, caqVccParamsFrtt, caqVccParamsNrm, caqVccParamsInvTrm, caqVccParamsInvCdf, caqVccParamsAdtf } STATUS current DESCRIPTION "Add-on objects providing per-VC ATM QoS related info." ::= { ciscoAtmQosMIBGroups 2 } ciscoAtmQosVpcGroup OBJECT-GROUP OBJECTS { caqVpcParamsVpState, caqVpcParamsPeakRate, caqVpcParamsCesRate, caqVpcParamsDataVcCount, caqVpcParamsCesVcCount, caqVpcParamsVcdF4Seg, caqVpcParamsVcdF4Ete, caqVpcParamsScr, caqVpcParamsMbs } STATUS current DESCRIPTION "A collection of objects providing per-VP ATM QoS related info." ::= { ciscoAtmQosMIBGroups 3 } ciscoAtmQosVpcAddon1Group OBJECT-GROUP OBJECTS { caqVpcParamsAvailBw } STATUS current DESCRIPTION "Add-on objects providing per-VP ATM QoS related info." ::= { ciscoAtmQosMIBGroups 4 } ciscoAtmQosVcQueuingGroup OBJECT-GROUP OBJECTS { caqQueuingParamsMeanQDepth, caqQueuingParamsClassRandDrp, caqQueuingParamsClassTailDrp, caqQueuingParamsClassMinThre, caqQueuingParamsClassMaxThre, caqQueuingParamsClassMrkProb } STATUS current DESCRIPTION "A collection of objects providing per-VC queuing/buffering related info." ::= { ciscoAtmQosMIBGroups 5 } END