| cfaAdapterIfVcQThresholdEntry |
.1.3.6.1.4.1.9.9.110.1.1.1.1 |
|
A set of per-VC queue threshold parameters that are used
for congestion control for Frame Relay/FUNI to ATM
Interworking Function connections, on the Frame Relay Port
Adapter Module.
The ifIndex in the index clause refers to MIB-II's
ifIndex corresponding to frame-based ATM PAM ports,
i.e., Frame Relay and FUNI.
|
| cfaAdapterIfVbrServOflowEntry |
.1.3.6.1.4.1.9.9.110.1.1.2.1 |
|
A set of Resource Management parameters that are used
for VBR Overflow Servicing for Frame Relay/FUNI to ATM
Interworking Function connections, on the Frame Relay
Port Adapter Module.
|
| cfaAdapterIfFrConfigEntry |
.1.3.6.1.4.1.9.9.110.1.1.3.1 |
|
An entry in the table, containing information about
Resource Management of an Interface with Frame Relay
encapsulation.
|
| cfaInterworkIfResourceEntry |
.1.3.6.1.4.1.9.9.110.1.2.1.1 |
|
A set of objects that can be used to view
available and allocated resources on Frame Relay
and FUNI interfaces defined on a Frame Relay Port
Adapter Module (PAM).
|
| cfaAdapterIfVcQService |
.1.3.6.1.4.1.9.9.110.1.1.1.1.1 |
|
The service category of the connection to which this
entry applies.
|
| cfaAdapterIfVcQInqDiscThresh |
.1.3.6.1.4.1.9.9.110.1.1.1.1.2 |
|
This object defines the Discard Eligible threshold
applied to the Frame Relay - ATM interworking
virtual circuit input queue, on the Frame Relay
PAM.
The input queue is in the direction of
Frame Relay/FUNI interface to the ATM switch fabric.
If the fill level of the input queue for the
Frame Relay - ATM interworking virtual circuit
exceeds this threshold, all frames arriving on
this virtual circuit from the Frame Relay side will
be discarded at the interface if the arriving
frame has its Discard Eligible bit set.
The threshold value is expressed as a
percent-of-full. Setting this object to 100
effectively turns off the threshold.
|
| cfaAdapterIfVcQOutqDiscThresh |
.1.3.6.1.4.1.9.9.110.1.1.1.1.3 |
|
This object defines the Discard Eligible threshold
applied to the Frame Relay - ATM interworking
virtual circuit output queue, on the Frame Relay
PAM.
The output queue is in the direction of the ATM
switch fabric to the Frame Relay/FUNI interface.
If the fill level of the output queue for the
Frame Relay - ATM interworking virtual circuit
exceeds this threshold, all frames arriving on
this virtual circuit from the ATM switch fabric
side will be discarded if the arriving frame has its
Discard Eligible bit set.
The threshold value is expressed as a
percent-of-full. Setting this object to 100
effectively turns off the threshold.
|
| cfaAdapterIfVcQInqMarkThresh |
.1.3.6.1.4.1.9.9.110.1.1.1.1.4 |
|
This object defines the Marking threshold
applied to the Frame Relay - ATM interworking
virtual circuit input queue, on the Frame Relay
PAM.
The input queue is in the direction of
Frame Relay/FUNI interface to the ATM switch fabric.
If the fill level of the input queue for the
Frame Relay - ATM interworking virtual circuit
exceeds this threshold, the following will
happen:
1. For frames coming into the Frame Relay -
ATM interworking virtual circuit from the Frame
Relay side, the corresponding cells will have
the Explicit Forward Congestion Indication (EFCI)
bit set in the ATM cell header, on entry into the
ATM switch fabric.
2. For cells arriving from the ATM switch fabric
side for this Frame Relay - ATM interworking
virtual circuit, the corresponding frames will have the
Backward Explicit Congestion Notification (BECN)
bit set upon exiting the Frame Relay interface.
The threshold value is expressed as a
percent-of-full. Setting this object to 100
effectively turns off the threshold.
|
| cfaAdapterIfVcQOutqMarkThresh |
.1.3.6.1.4.1.9.9.110.1.1.1.1.5 |
|
This object defines the Marking threshold
applied to the Frame Relay - ATM interworking
virtual circuit output queue, on the Frame Relay
PAM.
The output queue is in the direction of the ATM
switch fabric to the Frame Relay/FUNI interface.
If the fill level of the output queue for the
Frame Relay - ATM interworking virtual circuit
exceeds this threshold, the following will
happen:
1. For frames coming into the Frame Relay -
ATM interworking virtual circuit from the Frame
Relay side, the frame will have the BECN bit set
in the Frame Relay header before getting converted
to cells and entering the ATM switch fabric.
2. For cells arriving from the ATM switch fabric
side for this Frame Relay - ATM interworking
virtual circuit, the corresponding frames will
have the Forward Explicit Congestion Notification
(FECN) bit set in the Frame Relay header upon
exiting the Frame Relay interface. For FUNI -
ATM interworking connections, the Congestion
Notification (CN) bit gets set in the FUNI
header.
The threshold value is expressed as a
percent-of-full. Setting this object to 100
effectively turns off the threshold.
|
| cfaAdapterIfVbrServOflow |
.1.3.6.1.4.1.9.9.110.1.1.2.1.1 |
|
Configuration to enable the overflow feature for VBR-NRT
connections on the interface. When the PAM services VBR-NRT
VC input queues, sending ATM traffic to the switch
fabric, it can strictly limit the rate at which the data
is sent to contracted sustained cell rate (SCR) for the
connection (overflow disabled), or allow data transfer
over SCR (overflow enabled). Setting the value to true
enables overflow.
|
| cfaAdapterIfOverbooking |
.1.3.6.1.4.1.9.9.110.1.1.3.1.1 |
|
This object defines overbooking of CIR on an acess link/port
in percent of access rate. The total of all CIR's for all
frame-relay pvc's and frame-relay soft-vc's cannot exceed CIR
overbooking factor times access rate. For example,
overbooking of 200% means the total of all CIR's can be
configured up to twice of the access rate. The default is
100% - no overbooking is set.
|
| cfaInterworkIfVcQService |
.1.3.6.1.4.1.9.9.110.1.2.1.1.1 |
|
The service category of the connection to which this
entry applies.
|
| cfaInterworkIfRxAvailRate |
.1.3.6.1.4.1.9.9.110.1.2.1.1.2 |
|
The available bit rate for traffic received on the
Frame Relay interface. This is the bandwidth available
for connections. This value decreases as a
result of setup of a connection requesting non-zero
Committed Information Rate (CIR) in the receive direction,
and increases as a result of the release of such a
connection.
|
| cfaInterworkIfTxAvailRate |
.1.3.6.1.4.1.9.9.110.1.2.1.1.3 |
|
The available bit rate for traffic sent out the
Frame Relay interface. This is the bandwidth available
for connections. This value decreases as a
result of setup of a connection requesting non-zero CIR
in the transmit direction, and increases as a result of
the release of such a connection.
|
| cfaInterworkIfRxAllocRate |
.1.3.6.1.4.1.9.9.110.1.2.1.1.4 |
|
The allocated bit rate for traffic received on the
Frame Relay interface. This is the bandwidth allocated
to connections. This value increases as a
result of setup of a connection requesting non-zero CIR
in the receive direction, and decreases as a result of
the release of such a connection.
|
| cfaInterworkIfTxAllocRate |
.1.3.6.1.4.1.9.9.110.1.2.1.1.5 |
|
The allocated bit rate for traffic sent out the
Frame Relay interface. This is the bandwidth allocated
to connections. This value increases as a
result of setup of a connection requesting non-zero CIR
in the transmit direction, and decreases as a result of
the release of such a connection.
|
| cfaAdapterIfVcQThresholdTable |
.1.3.6.1.4.1.9.9.110.1.1.1 |
|
A table of per-VC queue threshold parameters that are used
for congestion control for Frame Relay/FUNI to ATM
Interworking Function connections, on the Frame Relay Port
Adapter Module.
These objects become available as each Frame Relay
and FUNI interface is defined on the device. The
corresponding ifTypes are frameRelayService(44)
and atmFuni(106) respectively.
An unique set of threshold parameters are available for
every supported Interworking Function service
category, and would be applied to all connections
belonging to that particular service category, on that
Frame Relay or FUNI interface.
|
| cfaAdapterIfVbrServOflowTable |
.1.3.6.1.4.1.9.9.110.1.1.2 |
|
A table of Resource Management parameters that are used
for VBR Overflow Servicing for Frame Relay/FUNI to ATM
Interworking Function connections, on the Frame Relay
Port Adapter Module.
This object becomes available as each Frame Relay
and FUNI interface is defined on the device. The
corresponding ifTypes are frameRelayService(44)
and atmFuni(106) respectively.
|
| cfaAdapterIfFrConfigTable |
.1.3.6.1.4.1.9.9.110.1.1.3 |
|
A table of resource management parameters for
the Frame Relay interface on the FR/FUNI Port
Adapter Module.
|
| cfaInterworkIfResourceTable |
.1.3.6.1.4.1.9.9.110.1.2.1 |
|
A table of objects that can be used to view
available and allocated resources on Frame Relay
and FUNI interfaces defined on a Frame Relay Port
Adapter Module (PAM).
An unique set of available and allocated resources
are available for the transmit direction (going out
of the interface to the external world), and
receive direction (coming into the interface from
the external world).
These available and allocated resources are available
for every supported Interworking Function service
category.
These objects become available as each Frame Relay
and FUNI interface is defined on the device. The
corresponding ifTypes are frameRelayService(44)
and atmFuni(106) respectively.
|
