CISCO-CAS-IF-MIB device MIB details by Cisco
CISCO-CAS-IF-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-CAS-IF-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-CAS-IF-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ***************************************************************** -- CISCO-CAS-IF-MIB.my: Channel Associated Signal Interface MIB file -- -- July 1997 Hongchi Shih -- Jan. 1999 Rick Chen -- -- Copyright (c) 1997-1999, 2000, 2003 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-CAS-IF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI RowStatus, TruthValue, DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF InterfaceIndex, ifIndex FROM IF-MIB CountryCode FROM CISCO-TC ciscoMgmt FROM CISCO-SMI; ciscoCasIfMIB MODULE-IDENTITY LAST-UPDATED "200304180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-voice@cisco.com" DESCRIPTION "Channel Associated Signal Interface MIB module. This MIB manages the generic CAS (Channel Associated Signal)or DS0 clear channel Interfaces in the router. " REVISION "200304180000Z" DESCRIPTION "Extend ccasGrpCfgServiceType to include h248 (9) and ds0xconn (10)" REVISION "200210020000Z" DESCRIPTION "Extend ccasGrpCfgServiceType to include trunkingService(8)." REVISION "9901180000Z" DESCRIPTION "Add ccasXgcpCfgTable to configure continuity test (COT) tone frequencies. Add object ccasGrpCfgServiceType for displaying service type. Extend ccsaGrpCfgType to include fgdOS, fgdEANA and nullSignaling" ::= { ciscoMgmt 85 } -- -- ifEntry for the all type of Channel Associated Signal channel (CAS) -- supports the ifGeneralInformationGroup of Cisco IF-MIB. -- -- ifTable Comments -- ============== ================================================== -- ifIndex Each CAS channel is represented by an ifEntry. -- ifDescr Textual CAS channel description. -- ifType The IANA value of ds0(81) -- -- ifSpeed contains 64000 for CAS channel. -- ifPhysAddress contains an octet string of zero length. -- -- ifAdminStatus Only support the read-only ifAdminStatus. -- ifOperStatus The current operational status of the CAS channel -- interface port. Note that dormant(5) is explicitly -- being used as defined in RFC 1573. -- ifLastChange Refer to RFC 1573. -- ifLinkUpDownTrapEnable -- Only support the read-only ifLinkUpDownTrapEnable. -- It contains a 'disabled(2)' value. -- ifConnectorPresent -- Refer to RFC 1573. -- ifHighSpeed contains a zero value. -- ifName Refer to RFC 1573. -- ifAlias Only support the read-only ifAlias. It contains an -- octet string of zero length. -- -- -- Relationship to the IETF Dial Control MIB (RFC 2128) -- -- Associating and disassociating a CAS channel interface with -- a connection can be explicitly handled using an ifStack. If a -- call connection is established, the managed system stacks the call -- associated voice encapsulation interface on top of CAS channel of -- T1/E1. -- Refer to the section 2.2.1 of RFC 2128 and the section 3.2.1 of -- RFC 2127 for the detailed information. -- -- Using ifStackTable -- -- This section describes by example how to use ifStackTable to -- represent the relationship of dial-up peer with ds0 and ds1 -- interfaces. -- Examples given below are for illustration of active calls on -- voice encapsulation peers via ds0 of DS1. -- -- Example: A Voice Peer1 is being carried two active calls via two -- ds0 interfaces and Voice Peer2 is being carried one active -- call via one ds0 interface of the same DS1. -- -- +=============+ +=====+ -- | Voice | |Voice| -- | Peer1 | |Peer2| -- +=============+ +=====+ -- | | | <==== appears active -- | | | when the dial-up peer -- | | | connects to CAS channel -- +===+ +===+ +===+ -- |ds0| |ds0| |ds0| <==== CAS channels -- +===+ +===+ +===+ -- | | | -- +=====================+ -- | DS1 | -- +=====================+ -- -- The assignment of the index values could for example be: -- -- ifIndex Description -- 1 voice peer 1 (type 103) -- 2 voice peer 2 (type 103) -- 3 ds0 #1 (type 81) -- 4 ds0 #2 (type 81) -- 5 ds0 #3 (type 81) -- 7 ds1 (type 18) -- -- -- The ifStackTable is then used to show the relationships between the -- various interfaces. -- -- ifStackTable Entries -- -- HigherLayer LowerLayer -- 0 1 -- 0 2 -- 1 3 -- 1 4 -- 2 5 -- 3 7 -- 4 7 -- 5 7 -- 7 0 -- -- -- The Signaling type of the DS0 group is enhanced to include null -- signaling. When configured as null signaling, the DS0 group -- can provide voice/data path. ccasIfObjects OBJECT IDENTIFIER ::= { ciscoCasIfMIB 1 } ccasDS1Objects OBJECT IDENTIFIER ::= { ccasIfObjects 1 } ccasGrpObjects OBJECT IDENTIFIER ::= { ccasIfObjects 2 } ccasChannelObjects OBJECT IDENTIFIER ::= { ccasIfObjects 3 } ccasVoiceCfgObjects OBJECT IDENTIFIER ::= { ccasIfObjects 4 } ccasXgcpCfgObjects OBJECT IDENTIFIER ::= { ccasIfObjects 5 } ccasGrpGeneralObjects OBJECT IDENTIFIER ::= { ccasGrpObjects 1 } ccasGrpEMObjects OBJECT IDENTIFIER ::= { ccasGrpObjects 2 } ccasGrpLineObjects OBJECT IDENTIFIER ::= { ccasGrpObjects 3 } ccasGrpStaObjects OBJECT IDENTIFIER ::= { ccasGrpObjects 4 } ccasGrpABCDObjects OBJECT IDENTIFIER ::= { ccasGrpObjects 5 } --********************************************************************* -- The CAS/DS0 Interface Groups --********************************************************************* -- [1] CAS/DS0 General Configuration for T1/E1 -- [2] CAS/DS0 General Configuration group -- [3] CAS E&M group -- [4] CAS FXO/SAO group -- [5] CAS FXS/SAS group -- [6] CAS custom ABCD bits configuration group -- [7] CAS channel group --********************************************************************* -- The CAS/DS0 General Configuration Table for T1/E1 --********************************************************************* ccasDs1IfCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasDs1IfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS/DS0 General Configuration Table for T1/E1. It contains the CAS/DS0 related standard configuration information for T1/E1. " ::= { ccasDS1Objects 1 } ccasDs1IfCfgEntry OBJECT-TYPE SYNTAX CcasDs1IfCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the configuration table for each T1/E1. The entry is created when a T1/E1 hardware is detected. " INDEX { ifIndex } ::= { ccasDs1IfCfgTable 1 } CcasDs1IfCfgEntry ::= SEQUENCE { ccasDs1IfCfgDs0ChannelsConfigurable OCTET STRING } ccasDs1IfCfgDs0ChannelsConfigurable OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the bit map of the available DS0 channel in the DS1. The MSB (most significant bit) is DS0 channel number 1. The missing bytes is default to a value of 0. A 1-bit indicates the channel is available for configuration and a 0-bit indicates it isn't. The length of this object is either 3 octets (for T1) or 4 octets (for E1). The most significant bit is transmitted first. " ::= { ccasDs1IfCfgEntry 1 } --********************************************************************* -- The CAS/DS0 Group General Configuration Table --********************************************************************* ccasGrpCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS/DS0 Group Standard Configuration Table. It contains the general configuration information for the CAS/DS0 group of T1/E1 interfaces. " ::= { ccasGrpGeneralObjects 1 } ccasGrpCfgEntry OBJECT-TYPE SYNTAX CcasGrpCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A CAS/DS0 group entry. Each entry consists of the CAS group type and the CAS/DS0 group associated DS0 channels in a T1/E1. The value of ccasGrpCfgDs0Channels must be specified with at least one available DS0 channel in the CAS group associated T1/E1 before a new row in this table can become active(1). The entry of this table can only be created if the CAS/DS0 group associated DS1 ifEntry already exists. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpCfgTable 1 } CcasGrpCfgEntry ::= SEQUENCE { ccasGrpCfgIndex Integer32, ccasGrpCfgType INTEGER, ccasGrpCfgDs0Channels OCTET STRING, ccasGrpCfgServiceType INTEGER, ccasGrpCfgRowStatus RowStatus } ccasGrpCfgIndex OBJECT-TYPE SYNTAX Integer32 (0..30) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary index that uniquely identifies a DS0 group in a T1/E1. " ::= { ccasGrpCfgEntry 1 } ccasGrpCfgType OBJECT-TYPE SYNTAX INTEGER { emWinkStart (1), emWinkStartFgd (2), emImmedStart (3), emDelayDial (4), fxsLoopStart (5), fxsGroundStart (6), sasLoopStart (7), sasGroundStart (8), r2Analog (9), r2Digital (10), r2Pulse (11), p7 (12), fxoLoopStart (13), fxoGroundStart (14), fgdOS (15), nullSignaling (16), r1Itu (17), r1Modified (18), r1Turkey (19), fgdEANA (20) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Signaling type of the DS0 group. emWinkStart - CAS E&M Wink Start. emWinkStartFgd - CAS E&M Wink Start with Feature group D. emImmedStart - CAS E&M Immediate Start. emDelayDial - CAS E&M Delay Dial. fxsLoopStart - CAS FXS Loop Start. fxsGroundStart - CAS FXS Ground Start. sasLoopStart - CAS SAS Loop Start. sasGroundStart - CAS SAS Ground Start. r2Analog - R2 ITU Q411. r2Digital - R2 ITU Q421. r2Pulse - R2 ITU Supplement 7. p7 - P7 switch. fgdOS - Bellcore Feature Group D : Operator Services Signaling nullSignaling - 64k clear channel r1Itu - R1 ITU. r1Modified - R1 Modified. r1Turkey - R1 Turkey. fgdEANA - FGD Exchange Access North American. " REFERENCE "EIA/TIA-464B, chapter 6.2.1.1 Signaling Interface Types. ITU-T Q411 - Specifications of signalling system R2 line signalling, analogue version. ITU-T Q421 - Specifications of signalling system R2 line signalling, digital version. ITU-T R2 Supplement 7 - Specifications of signalling system R2 line signalling, pulsed version. Bellcore, TR-NPL-000258 - Feature Group D section 3.4 for Exchange Access North American section 3.6 for Operator Services Signaling " DEFVAL { emWinkStart } ::= { ccasGrpCfgEntry 2 } ccasGrpCfgDs0Channels OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains the bit map of the selected DS0 channels to be added into this group. The MSB (most significant bit) is DS0 channel number 1. For T1, only higher 24 bits are used to specify the the CAS channels for the CAS group. A 1-bit indicates the channel to be added into group and a 0-bit indicates it isn't. " DEFVAL { '00000000'H } ::= { ccasGrpCfgEntry 3 } ccasGrpCfgServiceType OBJECT-TYPE SYNTAX INTEGER { none (1), casServSw56 (2), casServModem (3), casServAuto (4), sgcp (5), mgcp (6), other (7), trunkingService (8), h248 (9), ds0xconn (10) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specify the Service type of the CAS/DS0 group. none - no service type casServSw56 - sw56 service for CAS casServModme - modem service for CAS casServAuto - auto service for CAS sgcp - Simple Gateway Control Protocol (SGCP) service. Used when DS0 is configured for null signaling. mgcp - Media Gateway Control Protocol (MGCP) service. Used when DS0 is configured for null signaling. other - none of the above and the below. trunkingService - This DS0 group is handled by trunking service application. h248 - ITU H.248 Media Gateway Control service. Used when DS0 is configured for null signaling. ds0xconn - Used for DS0 cross connection. " DEFVAL { none } ::= { ccasGrpCfgEntry 5 } ccasGrpCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The corresponding instance of ccasGrpCfgType can not be modified while this object has the value 'active'. " ::= { ccasGrpCfgEntry 4 } --********************************************************************* -- The CAS Group E&M Standard Configuration Table --********************************************************************* ccasGrpEMCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpEMCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS Group E&M Standard Configuration Table. It contains the CAS E&M group standard configuration information of T1/E1. " ::= { ccasGrpEMObjects 1 } ccasGrpEMCfgEntry OBJECT-TYPE SYNTAX CcasGrpEMCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the configuration table for each CAS E&M Group in the T1/E1. The entry is created when the ccasGrpCfgType is configured as 'em' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpEMCfgTable 1 } CcasGrpEMCfgEntry ::= SEQUENCE { ccasGrpEMCfgDialType INTEGER, ccasGrpEMCfgDnisAni BITS } ccasGrpEMCfgDialType OBJECT-TYPE SYNTAX INTEGER { dtmf (1), pulse (2), mf (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. mf - Multi-Frequency (MF) digit. The default value of this object is dtmf(1). " ::= { ccasGrpEMCfgEntry 1 } ccasGrpEMCfgDnisAni OBJECT-TYPE SYNTAX BITS { incomingDnis (0), incomingAni (1), outgoingDnis (2), outgoingAni (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the type of Destination Number Identification Service (DNIS) and Automatic Number Identification (ANI) support. MF tone supports both ANI and DNIS services. The DTMF tone only supports both incoming and outgoing DNIS. incomingDnis - support incoming DNIS feature. incomingAni - support incoming ANI feature. outgoingDnis - support outgoing DNIS feature. outgoingAni - support outgoing ANI feature. The default value of this object is '00'H. " ::= { ccasGrpEMCfgEntry 2 } --********************************************************************* -- The CAS Group E&M Timing Parameters Table --********************************************************************* -- This table contains the CAS Group E&M timing parameters information. ccasGrpEMTmTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpEMTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The E&M interface Timing Parameters table. It contains the configuration of the various E&M signaling protocol timing parameters. " ::= { ccasGrpEMObjects 2 } ccasGrpEMTmEntry OBJECT-TYPE SYNTAX CcasGrpEMTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the E&M Timing Parameters Table for each E&M interface." AUGMENTS { ccasGrpEMCfgEntry } ::= { ccasGrpEMTmTable 1 } CcasGrpEMTmEntry ::= SEQUENCE { ccasGrpEMTmClearWaitDuration Integer32, ccasGrpEMTmMaxWinkWaitDuration Integer32, ccasGrpEMTmMaxWinkDuration Integer32, ccasGrpEMTmDelayStart Integer32, ccasGrpEMTmMaxDelayDuration Integer32, ccasGrpEMTmMinDelayPulseWidth Integer32, ccasGrpEMTmDigitDuration Integer32, ccasGrpEMTmInterDigitDuration Integer32, ccasGrpEMTmPulseRate Integer32, ccasGrpEMTmPulseInterDigitDuration Integer32 } ccasGrpEMTmClearWaitDuration OBJECT-TYPE SYNTAX Integer32 (200..2000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time of Inactive incoming seizure signal to declare call cleared. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 400 milliseconds." ::= { ccasGrpEMTmEntry 1 } ccasGrpEMTmMaxWinkWaitDuration OBJECT-TYPE SYNTAX Integer32 (100..5000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum wink wait duration for sending out wink start signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 200 milliseconds." ::= { ccasGrpEMTmEntry 2 } ccasGrpEMTmMaxWinkDuration OBJECT-TYPE SYNTAX Integer32 (100..3000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum wink duration for sending out wink start signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emWinkStart(1) or emWinkStartFgd(2). The default value of this object is 200 milliseconds." ::= { ccasGrpEMTmEntry 3 } ccasGrpEMTmDelayStart OBJECT-TYPE SYNTAX Integer32 (20..2000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Timing of generation of outgoing delayed start signal from detection of incoming seizure. This object is relevant to the interfaces of the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 300 milliseconds." ::= { ccasGrpEMTmEntry 4 } ccasGrpEMTmMaxDelayDuration OBJECT-TYPE SYNTAX Integer32 (100..5000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum delay signal duration for sending out delay dial signaling. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 2000 milliseconds." ::= { ccasGrpEMTmEntry 5 } ccasGrpEMTmMinDelayPulseWidth OBJECT-TYPE SYNTAX Integer32 (0 | 140..5000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. This object is relevant to the interfaces in the CAS group if the ccasGrpCfgType object is emDelayDial(4). The default value of this object is 140 milliseconds." ::= { ccasGrpEMTmEntry 6 } ccasGrpEMTmDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF/MF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds. " ::= { ccasGrpEMTmEntry 7 } ccasGrpEMTmInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF/MF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds. " ::= { ccasGrpEMTmEntry 8 } ccasGrpEMTmPulseRate OBJECT-TYPE SYNTAX Integer32 (10..20) UNITS "pulses per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 10 pps. " ::= { ccasGrpEMTmEntry 9 } ccasGrpEMTmPulseInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (100..1000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 500 milliseconds. " ::= { ccasGrpEMTmEntry 10 } --********************************************************************* -- The CAS Group FXS/SAS Standard Configuration Table --********************************************************************* ccasGrpLineCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpLineCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS Group FXS/SAS Standard Configuration Table. It contains the CAS FXS/SAS group standard configuration information of T1/E1. " ::= { ccasGrpLineObjects 1 } ccasGrpLineCfgEntry OBJECT-TYPE SYNTAX CcasGrpLineCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the configuration table for each CAS FXS/SAS Group in the T1/E1. The entry is created when the ccasGrpCfgType is configured as 'fxs' or 'sas' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpLineCfgTable 1 } CcasGrpLineCfgEntry ::= SEQUENCE { ccasGrpLineCfgNumberRings Integer32, ccasGrpLineCfgSupDisconnect TruthValue, ccasGrpLineCfgDialType INTEGER } ccasGrpLineCfgNumberRings OBJECT-TYPE SYNTAX Integer32 (0..10) UNITS "rings" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of rings detected before closing loop. If the value of this object is 0, then the managed system answers immediately after the interface detects a incoming seizure if the ccasGrpCfgType is 'fxsGroundStart' or 'sasGroundStart'. The default value of this object is 1 ring. " ::= { ccasGrpLineCfgEntry 1 } ccasGrpLineCfgSupDisconnect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION " Specifies whether a supervisory disconnect signal will be presented to the interface when the connected party at the interface hangs up. this object is only relevant to the ccasGrpCfgType is fxsLoopStart or sasLoopStart. The default value of this object is 'true'. " ::= { ccasGrpLineCfgEntry 2 } ccasGrpLineCfgDialType OBJECT-TYPE SYNTAX INTEGER { dtmf (1), pulse (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1). " ::= { ccasGrpLineCfgEntry 3 } --********************************************************************* -- The FXS/SAS Timing Parameters Table --********************************************************************* -- This table contains the FXS/SAS interface timing parameters -- information. ccasGrpLineTmTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpLineTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FXS/SAS interface Timing Parameters table. It contains the configuration of the various FXS/SAS signaling protocol timing parameters. " ::= { ccasGrpLineObjects 2 } ccasGrpLineTmEntry OBJECT-TYPE SYNTAX CcasGrpLineTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the FXS/SAS Timing Parameters Table for each FXS/SAS interface." AUGMENTS { ccasGrpLineCfgEntry } ::= { ccasGrpLineTmTable 1 } CcasGrpLineTmEntry ::= SEQUENCE { ccasGrpLineTmDigitDuration Integer32, ccasGrpLineTmInterDigitDuration Integer32, ccasGrpLineTmPulseRate Integer32, ccasGrpLineTmPulseInterDigitDuration Integer32 } ccasGrpLineTmDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds. " ::= { ccasGrpLineTmEntry 1 } ccasGrpLineTmInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds. " ::= { ccasGrpLineTmEntry 2 } ccasGrpLineTmPulseRate OBJECT-TYPE SYNTAX Integer32 (10..20) UNITS "pulses per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 10 pps. " ::= { ccasGrpLineTmEntry 3 } ccasGrpLineTmPulseInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (100..1000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 500 milliseconds. " ::= { ccasGrpLineTmEntry 4 } --********************************************************************* -- The CAS Group FXO/SAO Standard Configuration Table --********************************************************************* -- This table contains the configuration information of FXO/SAO signal -- interface. ccasGrpStaCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpStaCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FXO/SAO standard configuration table. It contains FXO/SAO configuration parameters, one entry per FXO/SAO interface. The configuration information of this table is set by its default setting when the CAS group is created by the configuration commands. " ::= { ccasGrpStaObjects 1 } ccasGrpStaCfgEntry OBJECT-TYPE SYNTAX CcasGrpStaCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the standard configuration table for each FXO/SAO Group. The entry is created when the ccasGrpCfgType is configured as 'fxo' or 'sao' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpStaCfgTable 1 } CcasGrpStaCfgEntry ::= SEQUENCE { ccasGrpStaCfgNumberRings Integer32, ccasGrpStaCfgDialType INTEGER } ccasGrpStaCfgNumberRings OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "rings" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of rings sent before sending reorder to the originator and releasing resources. If the value of this object is 0, then sending reorder to the originator is disabled. The default value of this object is 20 rings. " ::= { ccasGrpStaCfgEntry 1 } ccasGrpStaCfgDialType OBJECT-TYPE SYNTAX INTEGER { dtmf (1), pulse (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1). " ::= { ccasGrpStaCfgEntry 2 } --********************************************************************* -- The FXO/SAO Timing Parameters Table --********************************************************************* -- This table contains the FXO/SAO interface timing parameters -- information. ccasGrpStaTmTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpStaTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FXO/SAO interface Timing Parameters table. It contains the configuration of the various FXO/SAO signaling protocol timing parameters. " ::= { ccasGrpStaObjects 2 } ccasGrpStaTmEntry OBJECT-TYPE SYNTAX CcasGrpStaTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the FXO/SAO Timing Parameters Table for each FXO/SAO interface." AUGMENTS { ccasGrpStaCfgEntry } ::= { ccasGrpStaTmTable 1 } CcasGrpStaTmEntry ::= SEQUENCE { ccasGrpStaTmDigitDuration Integer32, ccasGrpStaTmInterDigitDuration Integer32, ccasGrpStaTmPulseRate Integer32, ccasGrpStaTmPulseInterDigitDuration Integer32 } ccasGrpStaTmDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpStaCfgDialType is dtmf. The default value of this object is 100 milliseconds. " ::= { ccasGrpStaTmEntry 1 } ccasGrpStaTmInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (50..500) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing DTMF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpStaCfgDialType is dtmf. The default value of this object is 100 milliseconds. " ::= { ccasGrpStaTmEntry 2 } ccasGrpStaTmPulseRate OBJECT-TYPE SYNTAX Integer32 (10..20) UNITS "pulses per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 10 pps. " ::= { ccasGrpStaTmEntry 3 } ccasGrpStaTmPulseInterDigitDuration OBJECT-TYPE SYNTAX Integer32 (100..1000) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 500 milliseconds. " ::= { ccasGrpStaTmEntry 4 } --********************************************************************* -- The CAS group associated custom ABCD bits configuration Table --********************************************************************* -- This table contains the A/B/C/D bits handling parameters information. ccasGrpABCDCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasGrpABCDCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS group custom ABCD bits configuration table for E1. It contains A/B/C/D bits handling objects, one entry per CAS group on an E1 interface. " ::= { ccasGrpABCDObjects 1 } ccasGrpABCDCfgEntry OBJECT-TYPE SYNTAX CcasGrpABCDCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the custom ABCD configuration table for each CAS Group on an E1 interface. The entry is created when a CAS group is configured on a E1. The entry is deleted when the CAS Group is de-configured from E1. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpABCDCfgTable 1 } CcasGrpABCDCfgEntry ::= SEQUENCE { ccasGrpABCDCfgInvertBits BITS, ccasGrpABCDCfgUnusedBits BITS } ccasGrpABCDCfgInvertBits OBJECT-TYPE SYNTAX BITS { dBit (0), cBit (1), bBit (2), aBit (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the A/B/C/D bit mask to invert the A/B/C/D bits value before the A/B/C/D bits are sent or after the A/B/C/D bits are received. 1-bit - enable bit inversion. 0-bit - disable bit inversion. The default value of this object is '00'H " ::= { ccasGrpABCDCfgEntry 1 } ccasGrpABCDCfgUnusedBits OBJECT-TYPE SYNTAX BITS { dBit (0), cBit (1), bBit (2), aBit (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the Unused A/B/C/D bit values to transmit. If any A/B/C/D bit is unused, the bit values in this object will be used to transmit for the unused A/B/C/D bits. The default value of this object is '00'H " ::= { ccasGrpABCDCfgEntry 2 } --*********************************************************************** -- The CAS channel Standard Configuration Table --*********************************************************************** ccasChannelCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasChannelCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS channel Standard Configuration Table. It contains the standard configuration information of CAS channel of T1/E1. " ::= { ccasChannelObjects 1 } ccasChannelCfgEntry OBJECT-TYPE SYNTAX CcasChannelCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the configuration table for each CAS channel. The entry is created when a CAS channel is configured on a T1/E1 via configuration command. The entry is deleted when the CAS channel is de-configured from T1/E1. " INDEX { ifIndex } ::= { ccasChannelCfgTable 1 } CcasChannelCfgEntry ::= SEQUENCE { ccasChannelCfgDS1IfIndex InterfaceIndex, ccasChannelCfgGroup Integer32, ccasChannelCfgTimeSlot Integer32, ccasChannelCfgBusyOut TruthValue } ccasChannelCfgDS1IfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "the ifIndex of this CAS channel associated T1/E1. " ::= { ccasChannelCfgEntry 1 } ccasChannelCfgGroup OBJECT-TYPE SYNTAX Integer32 (0..30) MAX-ACCESS read-only STATUS current DESCRIPTION "The CAS channel associated CAS group number. " ::= { ccasChannelCfgEntry 2 } ccasChannelCfgTimeSlot OBJECT-TYPE SYNTAX Integer32(1..31) MAX-ACCESS read-only STATUS current DESCRIPTION "The CAS channel associated T1/E1 timeslot." ::= { ccasChannelCfgEntry 3 } ccasChannelCfgBusyOut OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The CAS channel busyout configuration. true - the CAS channel is busied out. false - the CAS is normal. The default value for this object is 'false'. " ::= { ccasChannelCfgEntry 4 } --*********************************************************************** -- The CAS channel Status Table --*********************************************************************** ccasChannelStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasChannelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CAS channel Status Table. It contains general information about the status of CAS channel. " ::= { ccasChannelObjects 2 } ccasChannelStatusEntry OBJECT-TYPE SYNTAX CcasChannelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the status table for each CAS channel. " AUGMENTS { ccasChannelCfgEntry } ::= { ccasChannelStatusTable 1 } CcasChannelStatusEntry ::= SEQUENCE { ccasChannelStatusRecvSignalBits BITS, ccasChannelStatusBusyOut TruthValue, ccasChannelStatusInfoType INTEGER, ccasChannelStatusXmitSignalBits BITS } ccasChannelStatusRecvSignalBits OBJECT-TYPE SYNTAX BITS { dBit (0), cBit (1), bBit (2), aBit (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The receive ABCD signaling bits for the CAS channel. aBit - the signaling bit in the 6th frame bBit - the signaling bit in the 12th frame cBit - the signaling bit in the 18th frame dBit - the signaling bit in the 24th frame the cBit and dBit are only valid for E1 or T1 interface is operating in extended superframe (ESF) mode. " REFERENCE "EIA/TIA-464B, chapter 6.2 Digital Signaling and Supervision " ::= { ccasChannelStatusEntry 1 } ccasChannelStatusBusyOut OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The CAS channel busyout state. true - the CAS channel is busied out. false - the CAS is normal. " ::= { ccasChannelStatusEntry 2 } ccasChannelStatusInfoType OBJECT-TYPE SYNTAX INTEGER { unknown (1), speech (2), data56 (3), audio31 (4), audio7 (5), video (6), fax (7), modem (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Information Transfer Capability for the current or last call. unknown - If since system startup there has been no call on this interface, this object has a value of unknown(1). speech - refers to a non-data connection data56 - 56k data. audio31 - audio 3.1 kHz; refers to data mode connections audio7 - audio 7 kHz; refer to data mode connections; 'Unrestricted digital information with tones/ announcements'. video - as defined in Q.931 fax - Facsimile modem - V.3x modem " REFERENCE "Q.931 [8], chapter 4.5.5, octet 3 of bearer capability information element, combined with the User Rate (as defined in octets 5 and 5a to 5d), if rate adoption is being used." ::= { ccasChannelStatusEntry 3 } ccasChannelStatusXmitSignalBits OBJECT-TYPE SYNTAX BITS { dBit (0), cBit (1), bBit (2), aBit (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit ABCD signaling bits for the CAS channel. aBit - the signaling bit in the 6th frame bBit - the signaling bit in the 12th frame cBit - the signaling bit in the 18th frame dBit - the signaling bit in the 24th frame the cBit and dBit are only valid for E1 or T1 interface is operating in extended superframe (ESF) mode. " REFERENCE "EIA/TIA-464B, chapter 6.2 Digital Signaling and Supervision " ::= { ccasChannelStatusEntry 4 } -- -- Voice specific Configuration Table for a DS0 group -- ccasVoiceCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasVoiceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The voice specific configuration Table. It contains information about the voice related configuration parameters for a CAS group. " ::= { ccasVoiceCfgObjects 1 } ccasVoiceCfgEntry OBJECT-TYPE SYNTAX CcasVoiceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the voice specific configuration table for each CAS/DS0 group of a DS1. The entry is created if the associated CAS/DS0 group is created and the voice hardware is detected to support the voice capability for the CAS/DS0 group in the managed system. The entry is deleted when its associated CAS/DS0 group is deleted. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasVoiceCfgTable 1 } CcasVoiceCfgEntry ::= SEQUENCE { ccasVoiceCfgNoiseRegEnable TruthValue, ccasVoiceCfgNonLinearProcEnable TruthValue, ccasVoiceCfgMusicOnHoldThreshold Integer32, ccasVoiceCfgInGain Integer32, ccasVoiceCfgOutAttn Integer32, ccasVoiceCfgEchoCancelEnable TruthValue, ccasVoiceCfgEchoCancelCoverage INTEGER, ccasVoiceCfgConnectionMode INTEGER, ccasVoiceCfgConnectionNumber DisplayString, ccasVoiceCfgInitialDigitTimeOut Integer32, ccasVoiceCfgInterDigitTimeOut Integer32, ccasVoiceCfgRegionalTone CountryCode } ccasVoiceCfgNoiseRegEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates whether or not the background noise should be played to fill silence gaps if VAD is activated. The default value of this object is 'true'. " ::= { ccasVoiceCfgEntry 1 } ccasVoiceCfgNonLinearProcEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates whether or not the Nonlinear Processing is enabled for the interface. The default value of this object is 'true'. " ::= { ccasVoiceCfgEntry 2 } ccasVoiceCfgMusicOnHoldThreshold OBJECT-TYPE SYNTAX Integer32 (-70..-30) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the Music On Hold Threshold for the interface. The default value of this object is -38 dBm. " ::= { ccasVoiceCfgEntry 3 } ccasVoiceCfgInGain OBJECT-TYPE SYNTAX Integer32 (-6..14) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel). " ::= { ccasVoiceCfgEntry 4 } ccasVoiceCfgOutAttn OBJECT-TYPE SYNTAX Integer32 (0..14) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the amount of attenuation inserted at the transmit side of the interface. The output attenuation settings only define a loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel). " ::= { ccasVoiceCfgEntry 5 } ccasVoiceCfgEchoCancelEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies whether or not the Echo Cancellation is enabled for the interface. The default value of this object is 'true'. " ::= { ccasVoiceCfgEntry 6 } ccasVoiceCfgEchoCancelCoverage OBJECT-TYPE SYNTAX INTEGER { echoCanceller8ms (1), echoCanceller16ms (2), echoCanceller24ms (3), echoCanceller32ms (4), echoCanceller64ms (5), echoCanceller128ms(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the Echo Canceller coverage for the interface. This object is valid if the ccasVoiceCfgEchoCancelEnable object is 'true'. echoCanceller8ms - 8 milliseconds echo canceller coverage. echoCanceller16ms - 16 milliseconds echo canceller coverage. echoCanceller24ms - 24 milliseconds echo canceller coverage. echoCanceller32ms - 32 milliseconds echo canceller coverage. echoCanceller64ms - 64 milliseconds echo canceller coverage. echoCanceller128ms- 128 milliseconds echo canceller coverage. The default value of this object is echoCanceller8ms. " ::= { ccasVoiceCfgEntry 7 } ccasVoiceCfgConnectionMode OBJECT-TYPE SYNTAX INTEGER { normal (1), trunk (2), plar (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates the connection mode of the interface. normal - the interface acts normally to handle incoming and outgoing call. trunk - the interface acts in trunking mode. trunking mode causes two interfaces (on either the same or different routers) to be always conferenced together, and for telephony signaling to be passed transparently through the VoIP system rather than trapped and interpreted by the session application on the router(s). plar - the interface acts in PLAR (private line automatic ringdown) mode. PLAR is handled by associating a peer directly with an interface such that when the interface goes off-hook, that peer is used to setup the second call leg and conference them together without the caller having to dial any digits. " ::= { ccasVoiceCfgEntry 8 } ccasVoiceCfgConnectionNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the E.164 phone number that is used to establish connection with trunking mode or PLAR mode. If the ccasVoiceCfgConnectionMode is 'normal', then this object will be a zero length string. " ::= { ccasVoiceCfgEntry 9 } ccasVoiceCfgInitialDigitTimeOut OBJECT-TYPE SYNTAX Integer32 (0..120) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This is the initial digit timeout that indicates the amount of time the managed system waits for an initial input digit from the caller. The timer is activated when the call is accepted and is deactivated upon digit input. If the timer expires, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds. " ::= { ccasVoiceCfgEntry 10 } ccasVoiceCfgInterDigitTimeOut OBJECT-TYPE SYNTAX Integer32 (0..120) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This is the inter-digit timeout that indicates the amount of time the managed system waits for a subsequent input digit from the caller. The timer is started upon receipt of an input digit and restarted as each digit is received until the destination address is identified. If the timer expires and no destination address is identified, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds. " ::= { ccasVoiceCfgEntry 11 } ccasVoiceCfgRegionalTone OBJECT-TYPE SYNTAX CountryCode MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the current regional setting for the call progress tone to be used by this CAS group. " ::= { ccasVoiceCfgEntry 12 } -- -- XGCP Configuration Table for a DS0 group -- ccasXgcpCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF CcasXgcpCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The XGCP configuration Table contains information about DS0 usage by XGCP(SGCP/MGCP). XGCP is meant to represent both Simple Gateway Control Protocol (SGCP) and Media Gateway Control Protocol (MGCP). " ::= { ccasXgcpCfgObjects 1 } ccasXgcpCfgEntry OBJECT-TYPE SYNTAX CcasXgcpCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the configuration table for each DS0 group of a DS1. The entry is created if the DS0 group is configured as null-signaling and ccasGrpCfgServiceType is configured as either sgcp or mgcp. The entry is deleted when the signaling type is configured as non null-signaling. " INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasXgcpCfgTable 1 } CcasXgcpCfgEntry ::= SEQUENCE { ccasXgcpCfgCotToneCo1 Integer32, ccasXgcpCfgCotToneCo2 Integer32 } ccasXgcpCfgCotToneCo1 OBJECT-TYPE SYNTAX Integer32 (280..3800) UNITS "hertz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the continuity test tone frequencies for co1. Co1 is the COT tone frequency from the terminating switch in transponder mode and is from the originating switch in loopback mode. " REFERENCE "Bellcore GR-317-CORE spec, Rev 3, Nov. 1996, section 3.1.1.3. " ::= { ccasXgcpCfgEntry 1 } ccasXgcpCfgCotToneCo2 OBJECT-TYPE SYNTAX Integer32 (280..3800) UNITS "hertz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the continuity test tone frequencies for co2. Co2 is the COT tone frequency from the originating switch only in transponder mode. " REFERENCE "Bellcore GR-317-CORE spec, Rev 3, Nov. 1996, section 3.1.1.3. " ::= { ccasXgcpCfgEntry 2 } --*********************************************************************** -- Conformance and compliance statements --*********************************************************************** -- conformance information ccasIfMIBConformance OBJECT IDENTIFIER ::= { ciscoCasIfMIB 3 } ccasIfMIBCompliances OBJECT IDENTIFIER ::= { ccasIfMIBConformance 1 } ccasIfMIBGroups OBJECT IDENTIFIER ::= { ccasIfMIBConformance 2 } -- compliance statements ccasIfMIBCompliance MODULE-COMPLIANCE STATUS obsolete -- superseded by ccasIfMIBComplianceRev1 DESCRIPTION "The compliance statement for entities which implement the Cisco Voice Digital interface MIB" MODULE -- compliance to this module MANDATORY-GROUPS { ccasIfDS1Group, ccasGeneralInfoGroup } GROUP ccasEMGroup DESCRIPTION "The CAS E&M group is mandatory for T1/E1 that supports CAS E&M signal interface. " GROUP ccasLineGroup DESCRIPTION "The CAS Line group is mandatory for T1/E1 that supports CAS FXO/SAO signal interfaces. " GROUP ccasStaGroup DESCRIPTION "The CAS Station group is mandatory for T1/E1 that supports CAS FXS/SAS signal interfaces. " GROUP ccasCustomABCDGroup DESCRIPTION "The CAS custom ABCD bits configuration group is mandatory for E1 that supports CAS signal interfaces. " GROUP ccasVoiceGroup DESCRIPTION "The CAS Voice group is mandatory for a CAS group that supports voice/fax call capability. " OBJECT ccasGrpCfgType MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpCfgDs0Channels MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpCfgRowStatus MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpEMCfgDialType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpEMCfgDnisAni MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpABCDCfgInvertBits MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpABCDCfgUnusedBits MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgNoiseRegEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgNonLinearProcEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgMusicOnHoldThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgInGain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgOutAttn MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgEchoCancelEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgEchoCancelCoverage MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgConnectionMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgConnectionNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgInitialDigitTimeOut MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgInterDigitTimeOut MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasVoiceCfgRegionalTone MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ccasIfMIBCompliances 1 } ccasIfMIBComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Voice Digital interface MIB" MODULE -- compliance to this module MANDATORY-GROUPS { ccasIfDS1Group, ccasGeneralInfoGroupRev1 } GROUP ccasEMGroup DESCRIPTION "The CAS E&M group is mandatory for T1/E1 that supports CAS E&M signal interface. " GROUP ccasLineGroup DESCRIPTION "The CAS Line group is mandatory for T1/E1 that supports CAS FXO/SAO signal interfaces. " GROUP ccasStaGroup DESCRIPTION "The CAS Station group is mandatory for T1/E1 that supports CAS FXS/SAS signal interfaces. " GROUP ccasCustomABCDGroup DESCRIPTION "The CAS custom ABCD bits configuration group is mandatory for E1 that supports CAS signal interfaces. " GROUP ccasVoiceGroup DESCRIPTION "The CAS Voice group is mandatory for a CAS group that supports voice/fax call capability. " GROUP ccasChannelInfoGroup DESCRIPTION "The Channel Info group is mandatory for providing channel signaling information applicable to Channel Associated Signaling interfaces. " GROUP ccasXgcpCfgGroup DESCRIPTION "The XGCP Cfg group is mandatory for DS0 group that supports XGCP protocol entity. " OBJECT ccasGrpCfgType MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpCfgDs0Channels MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpCfgRowStatus MIN-ACCESS read-only DESCRIPTION "Create/Write access is not required." OBJECT ccasGrpEMCfgDialType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpEMCfgDnisAni MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpABCDCfgInvertBits MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ccasGrpABCDCfgUnusedBits MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ccasIfMIBCompliances 2 } -- units of conformance ccasIfDS1Group OBJECT-GROUP OBJECTS { ccasDs1IfCfgDs0ChannelsConfigurable } STATUS current DESCRIPTION "The collection of objects providing CAS/DS0 related T1/E1 information. " ::= { ccasIfMIBGroups 1 } ccasGeneralInfoGroup OBJECT-GROUP OBJECTS { ccasGrpCfgType, ccasGrpCfgDs0Channels, ccasGrpCfgRowStatus, ccasChannelCfgDS1IfIndex, ccasChannelCfgGroup, ccasChannelCfgTimeSlot, ccasChannelCfgBusyOut, ccasChannelStatusRecvSignalBits, ccasChannelStatusBusyOut, ccasChannelStatusInfoType, ccasChannelStatusXmitSignalBits } STATUS obsolete -- superseded by ccasGeneralInfoGroupRev1 DESCRIPTION "A collection of objects providing general information applicable to Channel Associated Signaling interfaces. " ::= { ccasIfMIBGroups 2 } ccasEMGroup OBJECT-GROUP OBJECTS { ccasGrpEMCfgDialType, ccasGrpEMCfgDnisAni, ccasGrpEMTmClearWaitDuration, ccasGrpEMTmMaxWinkWaitDuration, ccasGrpEMTmMaxWinkDuration, ccasGrpEMTmDelayStart, ccasGrpEMTmMaxDelayDuration, ccasGrpEMTmMinDelayPulseWidth, ccasGrpEMTmDigitDuration, ccasGrpEMTmInterDigitDuration, ccasGrpEMTmPulseRate, ccasGrpEMTmPulseInterDigitDuration } STATUS current DESCRIPTION "A collection of objects providing information applicable to the CAS E&M signal interfaces. " ::= { ccasIfMIBGroups 3 } ccasLineGroup OBJECT-GROUP OBJECTS { ccasGrpLineCfgNumberRings, ccasGrpLineCfgSupDisconnect, ccasGrpLineCfgDialType, ccasGrpLineTmDigitDuration, ccasGrpLineTmInterDigitDuration, ccasGrpLineTmPulseRate, ccasGrpLineTmPulseInterDigitDuration } STATUS current DESCRIPTION "A collection of objects providing information applicable to the CAS FXS/SAS signal interfaces. " ::= { ccasIfMIBGroups 4 } ccasStaGroup OBJECT-GROUP OBJECTS { ccasGrpStaCfgNumberRings, ccasGrpStaCfgDialType, ccasGrpStaTmDigitDuration, ccasGrpStaTmInterDigitDuration, ccasGrpStaTmPulseRate, ccasGrpStaTmPulseInterDigitDuration } STATUS current DESCRIPTION "A collection of objects providing information applicable to the CAS FXO/SAO signal interfaces. " ::= { ccasIfMIBGroups 5 } ccasCustomABCDGroup OBJECT-GROUP OBJECTS { ccasGrpABCDCfgInvertBits, ccasGrpABCDCfgUnusedBits } STATUS current DESCRIPTION "A collection of objects providing ABCD bits configuration information applicable to the CAS group on E1 interface. " ::= { ccasIfMIBGroups 6 } ccasVoiceGroup OBJECT-GROUP OBJECTS { ccasVoiceCfgNoiseRegEnable, ccasVoiceCfgNonLinearProcEnable, ccasVoiceCfgMusicOnHoldThreshold, ccasVoiceCfgInGain, ccasVoiceCfgOutAttn, ccasVoiceCfgEchoCancelEnable, ccasVoiceCfgEchoCancelCoverage, ccasVoiceCfgConnectionMode, ccasVoiceCfgConnectionNumber, ccasVoiceCfgInitialDigitTimeOut, ccasVoiceCfgInterDigitTimeOut, ccasVoiceCfgRegionalTone } STATUS current DESCRIPTION "A collection of objects providing information applicable to the CAS/DS0 group that supports voice capability. " ::= { ccasIfMIBGroups 7 } ccasGeneralInfoGroupRev1 OBJECT-GROUP OBJECTS { ccasGrpCfgType, ccasGrpCfgDs0Channels, ccasGrpCfgServiceType, ccasGrpCfgRowStatus } STATUS current DESCRIPTION "A collection of objects providing general information applicable to CAS/DS0 interfaces. " ::= { ccasIfMIBGroups 8 } ccasChannelInfoGroup OBJECT-GROUP OBJECTS { ccasChannelCfgDS1IfIndex, ccasChannelCfgGroup, ccasChannelCfgTimeSlot, ccasChannelCfgBusyOut, ccasChannelStatusRecvSignalBits, ccasChannelStatusBusyOut, ccasChannelStatusInfoType, ccasChannelStatusXmitSignalBits } STATUS current DESCRIPTION "A collection of objects providing channel signaling information applicable to Channel Associated Signaling interfaces. " ::= { ccasIfMIBGroups 9 } ccasXgcpCfgGroup OBJECT-GROUP OBJECTS { ccasXgcpCfgCotToneCo1, ccasXgcpCfgCotToneCo2 } STATUS current DESCRIPTION "A collection of objects providing XGCP specific information applicable to DS0. " ::= { ccasIfMIBGroups 10 } END