CISCO-DLC-SWITCH-MIB device MIB details by Cisco
CISCO-DLC-SWITCH-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-DLC-SWITCH-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-DLC-SWITCH-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ***************************************************************** -- IBM DLC Switch MIB definition. -- -- September 1996, Dennis Ignacio. -- -- Copyright (c) 1996-1997, 1998 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- CISCO-DLC-SWITCH-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI MacAddress, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM RFC1213-MIB InterfaceIndexOrZero FROM IF-MIB ciscoMgmt FROM CISCO-SMI ; ciscoDlcSwitchMIB MODULE-IDENTITY LAST-UPDATED "9702190000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-fras@cisco.com" DESCRIPTION "This is the MIB module for objects used to manage FRAS sessions to the endstation. These objects are specific to downstream or enduster sessions only. It does not contain objects supported by the FRAS-HOST MIB which are specific to upstream or host-end sessions." ::= { ciscoMgmt 76 } -- -- The following functionality will be modelled in this MIB module: -- -- 1. Frame-Relay Access Support -- ciscoDlcSwitchMIBObjects OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIB 1} -- THE BNN FORMAT (RFC 1490 Routed Format) -- ============== -- -- The following FRAS types of connections are modeled in the BNN -- group of this MIB: -- -- 1. SDLC -- 2. LLC (Token-Ring or Ethernet) -- -- -- -- THE BAN FORMAT (RFC 1490 Bridged Format) -- ============== -- -- The following FRAS types of connections are modeled in the BAN -- group of this MIBi: -- -- 1. SDLC -- 2. LLC (Token-Ring or Ethernet) -- -- ------------------------------------------------------------- frasBnnSdlc OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIBObjects 1 } frasBnnLlc OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIBObjects 2 } frasBanSdlc OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIBObjects 3 } frasBanLlc OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIBObjects 4 } -- ************************************************************** -- * Textual convention definitions * -- ************************************************************** SAP ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Service Access Point - is a term that denotes the means by which a user entity in layer n+1 accesses a service of a provider entity in layer n." SYNTAX OCTET STRING (SIZE(1)) SdlcAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A hexadecimal address assigned to a secondary poll station of an SDLC device." SYNTAX OCTET STRING (SIZE(1)) -- ************************************************************* -- * * -- * D L C S W I T C H F R A S - B N N * -- * * -- * Boundary Network Node / Routed Format * -- * * -- ************************************************************* -- ************************************************************* -- * * -- * THE FRAS BNN SDLC CONNECTION TABLE * -- * * -- ************************************************************* frasBnnSdlcConTable OBJECT-TYPE SYNTAX SEQUENCE OF FrasBnnSdlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains mapping information for each SDLC Link Station in a FRAS-BNN to SDLC connection. All entries are derived entirely from the router configuration." ::= { frasBnnSdlc 1 } frasBnnSdlcConEntry OBJECT-TYPE SYNTAX FrasBnnSdlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the entries defined for a specific SDLC Link Station in a BNN-SDLC configuration." INDEX { ifIndex, bnnSdlcConAddress } ::= { frasBnnSdlcConTable 1 } FrasBnnSdlcConEntry ::= SEQUENCE { bnnSdlcConAddress SdlcAddress, bnnSdlcConState INTEGER, bnnSdlcConDlci Integer32, bnnSdlcConFRInterface InterfaceIndexOrZero, bnnSdlcConLocalSap SAP, bnnSdlcConRemoteSap SAP } bnnSdlcConAddress OBJECT-TYPE SYNTAX SdlcAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port." ::= { frasBnnSdlcConEntry 1 } bnnSdlcConState OBJECT-TYPE SYNTAX INTEGER { reset (1), testSent (2), xidexchg (3), connrqsent (4), sigstnwait (5), connrspwait (6), connrspsent (7), contacted (8), discwait (9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the FRAS state of the Link Station. reset - no activity testSent - TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state" ::= { frasBnnSdlcConEntry 2 } bnnSdlcConDlci OBJECT-TYPE SYNTAX Integer32 (16..1022) MAX-ACCESS read-only STATUS current DESCRIPTION "The Data Link Connection Identifier used for this particular connection." ::= { frasBnnSdlcConEntry 3 } bnnSdlcConFRInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Frame-Relay interface which the SDLC Link Station is using to connect to the Host." ::= { frasBnnSdlcConEntry 4 } bnnSdlcConLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The Local SAP for this SDLC station's corresponding LLC session to the host." ::= { frasBnnSdlcConEntry 5 } bnnSdlcConRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The Remote SAP for this SDLC station's corresponding LLC session to the host." ::= { frasBnnSdlcConEntry 6 } -- ************************************************************* -- * * -- * THE FRAS BNN LLC2 CONNECTION TABLE * -- * * -- ************************************************************* frasBnnLlcConTable OBJECT-TYPE SYNTAX SEQUENCE OF FrasBnnLlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for each End Station in a FRAS-BNN to LLC connection. The entries are derived entirely from the router configuration." ::= { frasBnnLlc 1 } frasBnnLlcConEntry OBJECT-TYPE SYNTAX FrasBnnLlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for a specific End Station's connection state in a BNN-LLC connection." INDEX { ifIndex, bnnLlcConDeviceMacAddress, bnnLlcConLanLocalSap, bnnLlcConLanRemoteSap } ::= { frasBnnLlcConTable 1 } FrasBnnLlcConEntry ::= SEQUENCE { bnnLlcConDeviceMacAddress MacAddress, bnnLlcConLanLocalSap SAP, bnnLlcConLanRemoteSap SAP, bnnLlcConLanInterface InterfaceIndexOrZero, bnnLlcConDlci Integer32, bnnLlcConState INTEGER, bnnLlcConLocalMacAddress MacAddress, bnnLlcConFrLocalSap SAP, bnnLlcConFrRemoteSap SAP } bnnLlcConDeviceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value is the End Station's Local Mac-Address." ::= { frasBnnLlcConEntry 1 } bnnLlcConLanLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS not-accessible STATUS current DESCRIPTION "The End Station's Local SAP." ::= { frasBnnLlcConEntry 2 } bnnLlcConLanRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS not-accessible STATUS current DESCRIPTION "The End Station's Remote SAP." ::= { frasBnnLlcConEntry 3 } bnnLlcConLanInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This is the physical interace which the End Station is attached to." ::= { frasBnnLlcConEntry 4 } bnnLlcConDlci OBJECT-TYPE SYNTAX Integer32 (16..1022) MAX-ACCESS read-only STATUS current DESCRIPTION "The Data Link Connection Identifier associated with the corresponding LLC2 session over Frame-Relay to the host." ::= { frasBnnLlcConEntry 5 } bnnLlcConState OBJECT-TYPE SYNTAX INTEGER { reset (1), testSent (2), xidexchg (3), connrqsent (4), sigstnwait (5), connrspwait (6), connrspsent (7), contacted (8), discwait (9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the FRAS state of the Link Station. reset - no activity testSent - TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state" ::= { frasBnnLlcConEntry 6 } bnnLlcConLocalMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Mac-Address configured as the End Station's target or Remote address." ::= { frasBnnLlcConEntry 7 } bnnLlcConFrLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The FRAS router's Local SAP." ::= { frasBnnLlcConEntry 8 } bnnLlcConFrRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The FRAS router's Remote SAP." ::= { frasBnnLlcConEntry 9 } -- ************************************************************* -- * * -- * D L C S W I T C H F R A S - B A N * -- * * -- * Boundary Access Node / 802.5 Bridged Format * -- * * -- ************************************************************* -- ************************************************************* -- * * -- * THE FRAS BAN SDLC CONNECTION TABLE * -- * * -- ************************************************************* frasBanSdlcConTable OBJECT-TYPE SYNTAX SEQUENCE OF FrasBanSdlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for each SDLC Link Station in a FRAS-BAN to SDLC connection. The entries are derived entirely from the router configuration." ::= { frasBanSdlc 1 } frasBanSdlcConEntry OBJECT-TYPE SYNTAX FrasBanSdlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for a specific SDLC Link Station in a configured for a BAN connection." INDEX { ifIndex, banSdlcConAddress, banSdlcConBanDlciMac } ::= { frasBanSdlcConTable 1 } FrasBanSdlcConEntry ::= SEQUENCE { banSdlcConLocalInterface InterfaceIndexOrZero, banSdlcConAddress SdlcAddress, banSdlcConBanDlciMac MacAddress, banSdlcConDlci Integer32, banSdlcConState INTEGER, banSdlcConVmac MacAddress, banSdlcConBniAddress MacAddress, banSdlcConFrLocalSap SAP, banSdlcConFrRemoteSap SAP } banSdlcConLocalInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This is the physical interface the SDLC Link Stations are connected to." ::= { frasBanSdlcConEntry 1 } banSdlcConAddress OBJECT-TYPE SYNTAX SdlcAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port." ::= { frasBanSdlcConEntry 2 } banSdlcConBanDlciMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The End Station's target or Remote mac-address." ::= { frasBanSdlcConEntry 3 } banSdlcConDlci OBJECT-TYPE SYNTAX Integer32 (16..1022) MAX-ACCESS read-only STATUS current DESCRIPTION "The Data Link Connection Identifier for the corresponding LLC2 session over Frame-Relay to the host." ::= { frasBanSdlcConEntry 4 } banSdlcConState OBJECT-TYPE SYNTAX INTEGER { reset (1), testSent (2), xidexchg (3), connrqsent (4), sigstnwait (5), connrspwait (6), connrspsent (7), contacted (8), discwait (9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the FRAS state of the Link Station. reset - no activity testSent- TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state" ::= { frasBanSdlcConEntry 5 } banSdlcConVmac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The End Station's virtual Mac-Address which is comprised of a TR formatted template and the SDLC Link Station address appended on the last nibble." ::= { frasBanSdlcConEntry 6 } banSdlcConBniAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "BNI is Boundary Node Identifier which is the FRAS-BAN connection's Remote address in TR-format. It is by default 4fff.0000.0000" ::= { frasBanSdlcConEntry 7 } banSdlcConFrLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The FRAS router's Local SAP." ::= { frasBanSdlcConEntry 8 } banSdlcConFrRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The FRAS router's Remote SAP." ::= { frasBanSdlcConEntry 9 } -- ************************************************************* -- * * -- * THE FRAS BAN LLC2 CONNECTION TABLE * -- * * -- ************************************************************* frasBanLlcConTable OBJECT-TYPE SYNTAX SEQUENCE OF FrasBanLlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for each LAN attached End Station in a FRAS-BAN to LAN connection. The entries are from endstations which have their destination mac-addresses as the BAN-DLCI-MAC address." ::= { frasBanLlc 1 } frasBanLlcConEntry OBJECT-TYPE SYNTAX FrasBanLlcConEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information for a specific LAN attached End Station." INDEX { banLlcEndstnLocalMac, banLlcConLocalSap, banLlcConRemoteSap, banLlcBanDlciMac } ::= { frasBanLlcConTable 1 } FrasBanLlcConEntry ::= SEQUENCE { banLlcEndstnLocalMac MacAddress, banLlcBanDlciMac MacAddress, banLlcConLocalSap SAP, banLlcConRemoteSap SAP, banLlcConDlci Integer32, banLlcConState INTEGER, banLlcConFrInterface InterfaceIndexOrZero, banLlcBniAddress MacAddress, banLlcConFrLocalSap SAP, banLlcConFrRemoteSap SAP } banLlcEndstnLocalMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This value is the End Station's Local Mac-Address." ::= { frasBanLlcConEntry 1 } banLlcBanDlciMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This value is the End Station's Remote Mac-Address. It is also the FRAS-BAN connection's Local Mac-Address." ::= { frasBanLlcConEntry 2 } banLlcConLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The endstation's Local SAP." ::= { frasBanLlcConEntry 3 } banLlcConRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The endstation's Remote SAP." ::= { frasBanLlcConEntry 4 } banLlcConDlci OBJECT-TYPE SYNTAX Integer32 (16..1022) MAX-ACCESS read-only STATUS current DESCRIPTION "The Data Link Connection Identifier associated with the corresponding LLC2 session over Frame-Relay to the host." ::= { frasBanLlcConEntry 5 } banLlcConState OBJECT-TYPE SYNTAX INTEGER { reset (1), testSent (2), xidexchg (3), connrqsent (4), sigstnwait (5), connrspwait (6), connrspsent (7), contacted (8), discwait (9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the FRAS state of the Link Station. reset - no activity testSent- TEST Frames sent xidexchg - XID exchange in progress connrqsent - Connect request sent sigstnwait - Signal station wait state connrspwait - Connect response wait state connrspsent - Connect response sent contacted - Session established discwait - Disconnect wait state" ::= { frasBanLlcConEntry 6 } banLlcConFrInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Frame-Relay interface for this particular session." ::= { frasBanLlcConEntry 7 } banLlcBniAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This value is the FRAS-BAN connection's Target Mac-Address. It is by default 4fff.0000.0000" ::= { frasBanLlcConEntry 8 } banLlcConFrLocalSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The Local SAP of the corresponding LLC2 session over Frame-Relay to the host." ::= { frasBanLlcConEntry 9 } banLlcConFrRemoteSap OBJECT-TYPE SYNTAX SAP MAX-ACCESS read-only STATUS current DESCRIPTION "The Remote SAP of the corresponding LLC2 session over Frame-Relay to the host." ::= { frasBanLlcConEntry 10 } -- ********************************************************************** -- * CONFORMANCE INFORMATION * -- ********************************************************************** ciscoDlcSwitchConformance OBJECT IDENTIFIER ::= { ciscoDlcSwitchMIB 2 } ciscoDlcSwitchCompliances OBJECT IDENTIFIER ::= { ciscoDlcSwitchConformance 1 } ciscoDlcSwitchGroups OBJECT IDENTIFIER ::= { ciscoDlcSwitchConformance 2 } -- -- COMPLIANCE STATEMENTS -- ciscoDlcSwitchCoreCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The core compliance statement for all FRAS connections." MODULE MANDATORY-GROUPS { frasBnnSdlcGroup, frasBnnLlcGroup, frasBanSdlcGroup, frasBanLlcGroup } ::= { ciscoDlcSwitchCompliances 1 } -- -- Core Conformance Groups for All Connection Components -- frasBnnSdlcGroup OBJECT-GROUP OBJECTS { bnnSdlcConState, bnnSdlcConDlci, bnnSdlcConFRInterface, bnnSdlcConLocalSap, bnnSdlcConRemoteSap } STATUS current DESCRIPTION "The frasBnnSdlcGroup defines objects which are common to the BNN SDLC of all compliant connections." ::= { ciscoDlcSwitchGroups 1 } frasBnnLlcGroup OBJECT-GROUP OBJECTS { bnnLlcConLanInterface, bnnLlcConDlci, bnnLlcConState, bnnLlcConLocalMacAddress, bnnLlcConFrLocalSap, bnnLlcConFrRemoteSap } STATUS current DESCRIPTION "The frasBnnLlcGroup defines objects which are common to the BNN LLC of all compliant connections." ::= { ciscoDlcSwitchGroups 2 } frasBanSdlcGroup OBJECT-GROUP OBJECTS { banSdlcConLocalInterface, banSdlcConAddress, banSdlcConBanDlciMac, banSdlcConDlci, banSdlcConState, banSdlcConVmac, banSdlcConBniAddress, banSdlcConFrLocalSap, banSdlcConFrRemoteSap } STATUS current DESCRIPTION "The frasBanSdlcGroup defines objects which are common to the BAN SDLC of all compliant connections." ::= { ciscoDlcSwitchGroups 3 } frasBanLlcGroup OBJECT-GROUP OBJECTS { banLlcEndstnLocalMac, banLlcBanDlciMac, banLlcConDlci, banLlcConLocalSap, banLlcConRemoteSap, banLlcConState, banLlcConFrInterface, banLlcBniAddress, banLlcConFrLocalSap, banLlcConFrRemoteSap } STATUS current DESCRIPTION "The frasBanLlcGroup defines objects which are common to the BAN LLC of all compliant connections." ::= { ciscoDlcSwitchGroups 4 } END