CISCO-DS0-CROSS-CONNECT-MIB device MIB details by Cisco

CISCO-DS0-CROSS-CONNECT-MIB file content

The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.

Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.

Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-DS0-CROSS-CONNECT-MIB.

Vendor:	Cisco
Mib:	CISCO-DS0-CROSS-CONNECT-MIB  [download]  [view objects]
Tool:	ActiveXperts Network Monitor 2024 [download]    (ships with advanced SNMP/MIB tools)

-- ********************************************************************
-- CISCO-DS0-CROSS-CONNECT-MIB.my
--
-- March 2003, Kiet Tran
--
-- Copyright (c) 2003 by cisco Systems, Inc.
-- All rights reserved.
--
-- *********************************************************************
CISCO-DS0-CROSS-CONNECT-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, Unsigned32
        FROM SNMPv2-SMI
    MODULE-COMPLIANCE, OBJECT-GROUP
        FROM SNMPv2-CONF
    InterfaceIndex         
        FROM IF-MIB
    RowStatus
        FROM SNMPv2-TC
    ciscoMgmt
        FROM CISCO-SMI;

ciscoDs0CrossConnectMIB    MODULE-IDENTITY
    LAST-UPDATED  "200303050000Z"
    ORGANIZATION  "Cisco Systems, Inc."
    CONTACT-INFO
		  "Cisco Systems
                   Customer Service

                   Postal: 170 W. Tasman Drive
                           San Jose, CA  95134
                           USA

		   Tel: +1 800 553-NETS

		   E-mail: cs-voice@cisco.com"
    DESCRIPTION
        "The MIB for Ds0 cross connection.
	"
    REVISION "200303050000Z"
    DESCRIPTION
        "Initial version of the MIB module."
    ::= { ciscoMgmt 9999 }


ciscoDs0CrossConnectMIBNotifs      OBJECT IDENTIFIER 
    ::= { ciscoDs0CrossConnectMIB 0 }

ciscoDs0CrossConnectMIBObjects     OBJECT IDENTIFIER 
    ::= { ciscoDs0CrossConnectMIB 1 }

ciscoDs0CrossConnectMIBConformance OBJECT IDENTIFIER 
    ::= { ciscoDs0CrossConnectMIB 2 }

cDs0CrossConnectConfig             OBJECT IDENTIFIER 
    ::= { ciscoDs0CrossConnectMIBObjects 1 }


-- ---------------------------------------------------------------------
--  cds0CrossConnectConfigTable
-- ---------------------------------------------------------------------

cds0CrossConnectConfigTable  OBJECT-TYPE
    SYNTAX           SEQUENCE OF Cds0CrossConnectConfigEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
        "This table is used to establish a DS0 cross connection.
         A DS0 cross connect is established by binding a unique
         DS0 group containing one or more DS0s of a single Ds1 
         interface to another unique DS0 group containing one or 
         more DS0s of a single DS1 interface.  
        "
	::= { cDs0CrossConnectConfig 1 }

cds0CrossConnectConfigEntry  OBJECT-TYPE
    SYNTAX           Cds0CrossConnectConfigEntry
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
	"An entry in cds0CrossConnectConfigTable table represents a DS0 
         cross connection. The two end point of the connection are:
            end point 1: cds0Endpt1Ds1 cds0Endpt1Ds0Group
            end point 2: cds0Endpt2Ds1 cds0Endpt2Ds0Group

         The end points of this connection should be entries
         of ccasGrpCfgTable and 'ccasGrpCfgServiceType' of 
         of the entries should be 'tdmxconn'. The ccasGrpCfgTable is 
         defined in CISCO-CAS-IF-MIB.
        "
    INDEX {cds0Endpt1Ds1, cds0Endpt1Ds0Group }
    ::= { cds0CrossConnectConfigTable 1 }

Cds0CrossConnectConfigEntry ::=
    SEQUENCE {
              cds0Endpt1Ds1           InterfaceIndex,
              cds0Endpt1Ds0Group      Unsigned32,
              cds0Endpt2Ds1           InterfaceIndex,
              cds0Endpt2Ds0Group      Unsigned32,
              cds0ConnRowStatus       RowStatus
             }

cds0Endpt1Ds1        OBJECT-TYPE
    SYNTAX           InterfaceIndex
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
        "The value of this object equals to the 'ifIndex' of a
         Ds1 interface.
         This Ds1 interface is used as the first end point of the 
         Ds0 connection.
        "
    ::= { cds0CrossConnectConfigEntry 1}

cds0Endpt1Ds0Group   OBJECT-TYPE
    SYNTAX           Unsigned32 (0..31)
    MAX-ACCESS       not-accessible
    STATUS           current
    DESCRIPTION
        "The value of this object identifies a Ds0 group which contains 
         one of more Ds0(s) within the Ds1 interface represented by
         'cDs0Endpt1Ds1'.
         This Ds0 group is used as the first end point of the 
         Ds0 connection.
        "
    ::= { cds0CrossConnectConfigEntry 2 }

cds0Endpt2Ds1        OBJECT-TYPE
    SYNTAX           InterfaceIndex
    MAX-ACCESS       read-create 
    STATUS           current
    DESCRIPTION
        "The value of this object equals to the 'ifIndex' of a
         Ds1 interface.
         This Ds1 interface is used as the second end point of the 
         Ds0 connection.
        "
    ::= { cds0CrossConnectConfigEntry 3}

cds0Endpt2Ds0Group   OBJECT-TYPE
    SYNTAX           Unsigned32 (0..31)
    MAX-ACCESS       read-create 
    STATUS           current
    DESCRIPTION
        "The value of this object identifies a Ds0 group which contains 
         one of more Ds0(s) within the Ds1 interface represented by
         'cDs0Endpt2Ds1'.
         This Ds0 group is used as the second end point of the 
         Ds0 connection. 
        "
    ::= { cds0CrossConnectConfigEntry 4 }

cds0ConnRowStatus    OBJECT-TYPE
    SYNTAX	     RowStatus
    MAX-ACCESS       read-create
    STATUS           current
    DESCRIPTION		
        "This object is used to create or delete an entry.

         The mandatory objects for creating an entry in this table:
           'cds0Endpt2Ds1'
           'cds0Endpt2Ds0Group'

         The following objects are not allowed to be modified after 
         the entry to be added:
           'cds0Endpt2Ds1'
           'cds0Endpt2Ds0Group'
        "
    ::= { cds0CrossConnectConfigEntry 5 }

-- *********************************************************************
-- Conformance and compliance statements
-- *********************************************************************

ciscoDs0CrossConnectMIBCompliances   OBJECT IDENTIFIER ::= 
				{ ciscoDs0CrossConnectMIBConformance 1 }

ciscoDs0CrossConnectMIBGroups        OBJECT IDENTIFIER  ::= 
                                { ciscoDs0CrossConnectMIBConformance 2}

ciscoDs0CrossConnectMIBCompliance MODULE-COMPLIANCE

    STATUS	     current
    DESCRIPTION
        "The compliance statement for Cisco agents which implement
         the CISCO-DSO-CROSS-CONNECT-MIB." 
    MODULE
    MANDATORY-GROUPS { cDs0CrossConnectConfigGroup
	 	     }
    ::= {ciscoDs0CrossConnectMIBCompliances 1 }


-- *********************************************************************
-- units of conformance
-- *********************************************************************

cDs0CrossConnectConfigGroup  OBJECT-GROUP
    OBJECTS {   
             cds0Endpt2Ds1,           
             cds0Endpt2Ds0Group,        
             cds0ConnRowStatus    
	    }

    STATUS	     current
    DESCRIPTION
        "A collection of objects for general configuration of  
         Ds0 cross connection."
    ::= { ciscoDs0CrossConnectMIBGroups 1 }

END