CISCO-DSP-MGMT-MIB device MIB details by Cisco
CISCO-DSP-MGMT-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-DSP-MGMT-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-DSP-MGMT-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ********************************************************************* -- CISCO-DSP-MGMT-MIB.my: Digital Signal Processing Management MIB file -- -- July 1997 Hongchi Shih -- -- Copyright (c) 1997-2000, 2003 by cisco Systems, Inc. -- All rights reserved. -- ********************************************************************* CISCO-DSP-MGMT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Gauge32, Integer32, Unsigned32 FROM SNMPv2-SMI TimeStamp, TruthValue, DisplayString FROM SNMPv2-TC entPhysicalIndex FROM ENTITY-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ciscoMgmt FROM CISCO-SMI; ciscoDspMgmtMIB MODULE-IDENTITY LAST-UPDATED "200310100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-voice@cisco.com" DESCRIPTION "Changing the DESCRIPTION of cdspMIBCardStateNotification to notify Manager whenever cdspCardState enters normal. " REVISION "200310100000Z" DESCRIPTION "Added object cdspDspNum to cdspStatusTable. " REVISION "200308200000Z" DESCRIPTION "Digital Signal Processing (DSP) Management MIB module. The MIB module monitors the DSP resource and status. Acronyms & Terms ================ DTMF - Dual Tone Multi-Frequency. DTMF uses two frequencies, the high frequency component and the low frequency component, to generate digit signals. " REVISION "200308140000Z" DESCRIPTION "(1) Added following objects to cdspCardStatusTable: cdspTotalDsp cdspFailedDsp cdspCongestedDsp cdspNormalDsp cdspNx64Dsp cdspDspSwitchOverThreshold (2) Added cdspVoiceParamTable (3) Added following objects to cdspStatusTable: cdspSigBearerChannelSplit cdspNumCongestionOccurrence (4) Added following enumerations to cdspOperState: congested (3) failed (4) (5) Added cdspStatusXTable " REVISION "200008140000Z" DESCRIPTION "Fix typo in the DESCRIPTION clause of cdspMIBEnableCardStatusNotification object; change 'cdspFatalNotification' to 'cdspMIBCardStateNotification'. " REVISION "9810170000Z" DESCRIPTION "Add new objects to support channelized DSP features. " ::= { ciscoMgmt 86 } -- Digital Signal Processing Management MIB objects definitions cdspMgmtNotifications OBJECT IDENTIFIER ::= { ciscoDspMgmtMIB 0 } cdspMgmtObjects OBJECT IDENTIFIER ::= { ciscoDspMgmtMIB 1 } cdspCardObjects OBJECT IDENTIFIER ::= { cdspMgmtObjects 1 } cdspObjects OBJECT IDENTIFIER ::= { cdspMgmtObjects 2 } cdspMIBNotificationEnables OBJECT IDENTIFIER ::= { cdspMgmtObjects 3 } cdspVoiceObjects OBJECT IDENTIFIER ::= { cdspMgmtObjects 4 } -- -- Digital Signal Processing Group -- -- This group contains the DSP related variables -- of the DSP Card -- -- DSP Card Table -- cdspCardStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CdspCardStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSP Card Table. It contains status information of the DSP cards present within the router. " ::= { cdspCardObjects 1 } cdspCardStatusEntry OBJECT-TYPE SYNTAX CdspCardStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSP card table indicates the DSP card state, resource utilization. Each entry is created when a DSP software is detected on a DSP card. The entry is deleted when the DSP card is deleted. " INDEX { entPhysicalIndex } ::= { cdspCardStatusTable 1 } CdspCardStatusEntry ::= SEQUENCE { cdspCardIndex Integer32, cdspCardState INTEGER, cdspCardResourceUtilization Unsigned32, cdspCardLastHiWaterUtilization Unsigned32, cdspCardLastResetTime TimeStamp, cdspCardMaxChanPerDSP Unsigned32, cdspTotalDsp Unsigned32, cdspFailedDsp Gauge32, cdspDspSwitchOverThreshold Unsigned32, cdspCongestedDsp Gauge32, cdspNormalDsp Gauge32, cdspNx64Dsp Unsigned32 } cdspCardIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The object corresponds to cardIndex in the chassis mib. If value of this object is 0, then the entry is not associated to cardIndex of the chassis mib. " ::= { cdspCardStatusEntry 1 } cdspCardState OBJECT-TYPE SYNTAX INTEGER { normal (1), warning (2), critical (3), fatal (4), offLine (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the current state of DSP card being monitored. normal - DSP card in normal condition. warning - DSP card has some problem and need attention. critical - DSP card has a major alarm. fatal - DSP card is not functional. DSP subsystem might reset DSP card to recover it from the fatal error condition. After the DSP card is reset successfully, the object cdspCardResourceUtilization and cdspCardLastHiWaterUtilization are reset to 0. If the fatal error is persistent in this object after card is reset, the card should be replaced. offLine - DSP card is in off-line maintenance state. " ::= { cdspCardStatusEntry 2 } cdspCardResourceUtilization OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the percentage of current DSP resource utilization of the card. The utilization is a ratio of number of busy DSP resources (for handling calls, transcoding, voice compression,...) to the total available DSP resources. " ::= { cdspCardStatusEntry 3 } cdspCardLastHiWaterUtilization OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the last high water mark of DSP resource utilization. This object is reset to 0 after DSP card is reset. " ::= { cdspCardStatusEntry 4 } cdspCardLastResetTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the last DSP card reset occurred. " ::= { cdspCardStatusEntry 5 } cdspCardMaxChanPerDSP OBJECT-TYPE SYNTAX Unsigned32 UNITS "channels" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of channels allowed in each DSP. The value is chosen in an implementation-dependent manner by the DSP functionality. The value of 0 in this object indicates Channelized DSP mode is turned off. " ::= { cdspCardStatusEntry 6 } cdspTotalDsp OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of DSPs in the card. " ::= { cdspCardStatusEntry 7 } cdspFailedDsp OBJECT-TYPE SYNTAX Gauge32 (0..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of DSPs in the failed state (i.e cdspOperstate is 'failed') " ::= { cdspCardStatusEntry 8 } cdspDspSwitchOverThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..2048) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the threshold of DSP failures. When 'cdspFailedDsp' reaches the value of this object, the voice gateway switchover will occur. The maximum value of this object can not be more than the value in 'cdspTotalDsp' " ::= { cdspCardStatusEntry 9 } cdspCongestedDsp OBJECT-TYPE SYNTAX Gauge32 (0..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of DSPs in the congested state (i.e cdspOperstate is 'congested'). " ::= { cdspCardStatusEntry 10 } cdspNormalDsp OBJECT-TYPE SYNTAX Gauge32 (0..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of DSPs in the normal state (i.e cdspOperstate is 'normal'). " ::= { cdspCardStatusEntry 11 } cdspNx64Dsp OBJECT-TYPE SYNTAX Unsigned32 (0..2048) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the number of DSPs that need to be set aside for making Nx64 calls. The max value of this object is limited to the value of the object 'cdspTotalDsp'. If this value is 0, it is not allowed to make any Nx64 call. The default value of this object is 0. " ::= { cdspCardStatusEntry 12 } -- -- DSP Table -- cdspStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF CdspStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Status information for the DSPs. This status table is used for tracking dangling DSP resources. The dangling DSP channel means that the DSP channel is reserved for serving calls but the channel is not used by active calls. The number of the dangling DSP channels can be computed by 'cdspInUseChannels - cdspActiveChannels'. " ::= { cdspObjects 1 } cdspStatusEntry OBJECT-TYPE SYNTAX CdspStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in cdspStatusTable indicates the DSP state and alarm conditions. Each entry is created when a DSP is detected on a DSP card. The entry is deleted when the DSP card is deleted. The 'entPhysicalIndex' represents a DSP entity, and the 'entPhysicalClass' is 'other(1)'. " INDEX { entPhysicalIndex } ::= { cdspStatusTable 1 } CdspStatusEntry ::= SEQUENCE { cdspOperState INTEGER, cdspAlarms Counter32, cdspLastAlarmCause INTEGER, cdspLastAlarmCauseText DisplayString, cdspLastAlarmTime TimeStamp, cdspTotalChannels Unsigned32, cdspInUseChannels Gauge32, cdspActiveChannels Gauge32, cdspSigBearerChannelSplit TruthValue, cdspNumCongestionOccurrence Counter32, cdspDspNum Unsigned32 } cdspOperState OBJECT-TYPE SYNTAX INTEGER { normal (1), shutdown (2), congested (3), failed (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the DSP. normal - DSP operates normally shutdown - DSP is shutdown due to fatal error congested - DSP does not accept call because the DSP buffer is full failed - DSP failed " ::= { cdspStatusEntry 1 } cdspAlarms OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the accumulated number of DSP Alarms. " ::= { cdspStatusEntry 2 } cdspLastAlarmCause OBJECT-TYPE SYNTAX INTEGER { other (1), noAlarm (2), dspFatalError (3), dspMemoryError (4), dspBufferError (5), dspDownloadError (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the current or last alarm state of DSP. other - none of the following noAlarm - alarm condition had not been detected dspFatalError - DSP fatal error dspMemoryError - DSP memory error is detected dspBufferError - DSP buffer error dspDownloadError - Failed to download software to DSP. The cdspOperState will be set to 'shutdown(2) if the alarm condition of DSP is persistent. " ::= { cdspStatusEntry 3 } cdspLastAlarmCauseText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the failure reason for the current or last DSP Alarm. It should be used only for direct, human-readable display and only if a management station is unable to decode the value of cdspLastAlarmCause. " ::= { cdspStatusEntry 4 } cdspLastAlarmTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the last DSP Alarm occurred. The value of this object is 0 if the value of cdspLastAlarmCause object is 'noAlarm'. " ::= { cdspStatusEntry 5 } cdspTotalChannels OBJECT-TYPE SYNTAX Unsigned32 UNITS "channels" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of channels in the DSP. This value is predetermined by the DSP functionality upon initialization. The value of 0 in this object indicates Channelized DSP mode is turned off. " ::= { cdspStatusEntry 6 } cdspInUseChannels OBJECT-TYPE SYNTAX Gauge32 UNITS "channels" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of channels that are reserved for serving calls. The value is incremented when the DSP channel is reserved for call setup and is decremented after the DSP channel is free due to call disconnection. " ::= { cdspStatusEntry 7 } cdspActiveChannels OBJECT-TYPE SYNTAX Gauge32 UNITS "channels" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of channels that are used by active calls to process media stream. The value is incremented after the reserved DSP channel enters call connection state and is decremented after the call is disconnected. " ::= { cdspStatusEntry 8 } cdspSigBearerChannelSplit OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if the DSP channels are splitted for signaling call and bearer call. If the value of this object is 'true' which means that signaling call and bearer call cannot share any DSP channel. This object is not applicable when Channelized DSP mode is turned off. " ::= { cdspStatusEntry 9 } cdspNumCongestionOccurrence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of congestion occurred on the DSP. This value is set to 0 when system is reset. " ::= { cdspStatusEntry 10 } cdspDspNum OBJECT-TYPE SYNTAX Unsigned32 (1..252) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the DSP number associated with this DSP entity. " ::= { cdspStatusEntry 11 } -- -- DSP Ext Table -- cdspStatusXTable OBJECT-TYPE SYNTAX SEQUENCE OF CdspStatusXEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the additional detailed state and statistics information for a DSP that supports the splitted signalling and bearer channels. " ::= { cdspObjects 2 } cdspStatusXEntry OBJECT-TYPE SYNTAX CdspStatusXEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of this table is created when its associated entry in cdspStatusTable is created and the value of cdspSigBearerChannelSplit object is 'true'. " AUGMENTS { cdspStatusEntry } ::= { cdspStatusXTable 1 } CdspStatusXEntry ::= SEQUENCE { cdspXNumberOfBearerCalls Gauge32, cdspXNumberOfSigCalls Gauge32, cdspXAvailableBearerBandwidth Gauge32, cdspXAvailableSigBandwidth Gauge32 } cdspXNumberOfBearerCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of bearer calls on the DSP. " ::= { cdspStatusXEntry 1 } cdspXNumberOfSigCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of signaling calls on the DSP. " ::= { cdspStatusXEntry 2 } cdspXAvailableBearerBandwidth OBJECT-TYPE SYNTAX Gauge32 UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "The percentage of channels on the DSP currently available for bearer calls. " ::= { cdspStatusXEntry 3 } cdspXAvailableSigBandwidth OBJECT-TYPE SYNTAX Gauge32 UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "The percentage of channels on the DSP currently available for signaling calls. " ::= { cdspStatusXEntry 4 } -- -- DSP Voice Table -- cdspVoiceParamTable OBJECT-TYPE SYNTAX SEQUENCE OF CdspVoiceParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on voice call setup related parameters for DSP resource. " ::= { cdspVoiceObjects 1 } cdspVoiceParamEntry OBJECT-TYPE SYNTAX CdspVoiceParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DSP table contains information regarding a single DSP resource associated voice call setup parameters. An entry in this table is created when a DSP is detected and the DSP resource can be used by voice applications. An entry in this table is deleted when the DSP associated card/module is removed from the system. The 'entPhysicalClass' for the entry is 'other'. " INDEX { entPhysicalIndex } ::= { cdspVoiceParamTable 1 } CdspVoiceParamEntry ::= SEQUENCE { cdspRtpSidPayloadType INTEGER, cdspRtcpControl TruthValue, cdspRtcpTransInterval Unsigned32, cdspRtcpRecvMultiplier Unsigned32, cdspVadAdaptive TruthValue, cdspDtmfPowerLevel Integer32, cdspDtmfPowerTwist Integer32 } cdspRtpSidPayloadType OBJECT-TYPE SYNTAX INTEGER { hexadecimal (19), decimal (13) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the RTP (Real Time Protocol) payload type of the SID (Silence Insertion Descriptor) packet that is sent to the remote endpoint at the onset of silence suppression. " REFERENCE "Section 5.1 of RFC2833 " DEFVAL { decimal } ::= { cdspVoiceParamEntry 1 } cdspRtcpControl OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This objects controls if RTCP (Real Time Control Protocol) will be enabled. If this object is set to 'true', both transmission and reception of RTCP packets are enabled; otherwise, transmission of RTCP packets is disabled while any received RTCP packets are ignored. " REFERENCE "Appendix A.7 of RFC1889 " DEFVAL { true } ::= { cdspVoiceParamEntry 2 } cdspRtcpTransInterval OBJECT-TYPE SYNTAX Unsigned32 (5000..65535) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This attribute specifies the RTCP report interval (defined in RFC1889). It indicates the interval in which the RTCP reports should be sent to the participating members. RTCP reports is sent out in a random interval computed by using 'cdspRtcpTransInterval' and a random number that is between 0.5 and 1.5. This interval timer also serves the purpose of RTP packets receive timer. At every interval multiplier times this interval, where a check is made on a VoIP connection (which is in SENDRECV or RECVONLY xGCP modes) to see if any RTP packets have been received. If not, gateway-initiated DLCX should be sent to the Call Agent. This object is applicable only if 'cdspRtcpControl' is set to 'true'. " REFERENCE "Appendix A.7 of RFC1889 " DEFVAL { 5000 } ::= { cdspVoiceParamEntry 3 } cdspRtcpRecvMultiplier OBJECT-TYPE SYNTAX Unsigned32 (1..60) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies an approximate RTCP report interval (defined in RFC 1889) in milliseconds in which the RTCP reports should be sent to the participating members. It specifies how many times the RTCP reports may fail before exception condition activity may be done. In the time elapse of value of this MIB object times the RTCP Report Interval specified by 'cdspRtcpTransInterval', a check will be done on a VoIP connection (which is in SENDRECV or RECVONLY xGCP modes) to see if any RTP packets have been received. If not, gateway-initiated DLCX should be sent to the Call Agent. This object is applicable only if 'cdspRtcpControl' is set to 'true'. " REFERENCE "Section 6.2.1 of RFC1889" DEFVAL { 5 } ::= { cdspVoiceParamEntry 4 } cdspVadAdaptive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This attribute is used to enable or disable the Adaptive VAD knob of the VAD algorithm. Adaptive VAD works in conjunction with VAD Threshold (cvifcfgMusicOnHoldThreshold from CISCO-VOICE-IF-MIB). When this object set to 'true', VAD Threshold is ignored and the DSP adjusts the threshold automatically according to the background noise level. When the adaptive VAD configuration is 'false', VAD threshold is used directly. The VAD configuration is ignored for all CODECs that contain their own VAD (G.729AB, G.723.1A and GSM-EFR). Likewise, when a channel is configured in ClearChannel mode (Clear Channel is Non-Compression CODEC channel), VAD will automatically be disabled irrespective of the configuration. " DEFVAL { false } ::= { cdspVoiceParamEntry 5 } cdspDtmfPowerLevel OBJECT-TYPE SYNTAX Integer32 (-250..30) UNITS "0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the power level of the low frequency component of DTMF. The power level of the high frequency component of DTMF is relative above or below the value specified in object cdspDtmfPowerTwist. If the value of cdspDtmfPowerTwist is 0, the power level of the high frequency component as well as the low frequency component is specified by this object." REFERENCE "Q.23, Q.24, EIA/TIA-464" DEFVAL { -120 } ::= { cdspVoiceParamEntry 6 } cdspDtmfPowerTwist OBJECT-TYPE SYNTAX Integer32 (-100..100) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the relative power level of the high frequency component of DTMF. The low frequency group is always fixed to the value specified by cdspDtmfPowerLevel. When this object is set to 0, the power level of both frequency components is set to the same level. When this object is set to a positive value, the power level of the high frequency component is set to relatively higher specified in this object than the low frequency component. For example if cdspDtmfPowerLevel is set to -120(-12 dBm) and this object is set to 50, the power level of the high frequency component becomes -70(-7 dBm). When this object is set to a negative value, the power level of the high frequency component is set to relatively lower specified in this object than the low frequency component. For example if cdspDtmfPowerLevel is set to -120(-12 dBm) and this object is set to -100, the power level of the high frequency component becomes -220(-22 dBm). The power level of the high frequency component has to be in the data range specified in cdspDtmfPowerLevel. For example if cdspDtmfPowerLevel is set to -200(-20 dBm) and this object is set to -100, the power level of the high frequency component will become -300(-30 dBm) which is out of the range (-250..30) of data specified in cdspDtmfPowerLevel, so -100 is illegitimate for this setting." REFERENCE "Q.23, Q.24, EIA/TIA-464" DEFVAL { 0 } ::= { cdspVoiceParamEntry 7 } cdspMIBEnableCardStatusNotification OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This variable controls whether the system produces the cdspMIBCardStateNotification. A false value will prevent DSP card fatal notifications from being generated by this system. " DEFVAL { false } ::= { cdspMIBNotificationEnables 1 } -- the following two OBJECT IDENTIFIERS are used to define SNMPv2 -- Notifications that are backward compatible with SNMPv1 Traps. cdspMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoDspMgmtMIB 2 } cdspMIBNotifications OBJECT IDENTIFIER ::= { cdspMIBNotificationPrefix 0 } cdspMIBCardStateNotification NOTIFICATION-TYPE OBJECTS { cdspCardState } STATUS current DESCRIPTION "A cdspMIBCardStateNotification is sent when the cdspCardState enters into normal(1) state and enters into or exits from fatal(4) state. " ::= { cdspMIBNotifications 1 } cdspMgmtConformance OBJECT IDENTIFIER ::= { ciscoDspMgmtMIB 3 } cdspMgmtCompliances OBJECT IDENTIFIER ::= { cdspMgmtConformance 1 } cdspMgmtGroups OBJECT IDENTIFIER ::= { cdspMgmtConformance 2 } -- compliance statements cdspMgmtCompliance MODULE-COMPLIANCE STATUS deprecated -- superseded by cdspMgmtComplianceRev1 DESCRIPTION "The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. " MODULE -- compliance to this module MANDATORY-GROUPS { cdspMgmtGeneralInfoGroup -- cdspMgmtNotificationsGroup } ::= { cdspMgmtCompliances 1 } cdspMgmtComplianceRev1 MODULE-COMPLIANCE STATUS deprecated -- superseded by cdspMgmtComplianceRev2 DESCRIPTION "The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. " MODULE -- compliance to this module MANDATORY-GROUPS { cdspMgmtGeneralInfoGroup -- ,cdspMgmtNotificationsGroup } GROUP cdspChannelGroup DESCRIPTION "This group is mandatory only if the DSP software offers multiple channels per DSP. " ::= { cdspMgmtCompliances 2 } cdspMgmtComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. " MODULE -- compliance to this module MANDATORY-GROUPS { cdspMgmtGeneralInfoGroup, cdspMgmtNotificationsGroup } GROUP cdspMgmtExtGeneralInfoGroup DESCRIPTION "This group is optional and it provides additional general DSP information. " GROUP cdspChannelGroup DESCRIPTION "This group is mandatory only if the DSP software offers multiple channels per DSP. " GROUP cdspChannelExtGroup DESCRIPTION "This group is optional and it provides additional DSP related information. " GROUP cdspVoiceInfoGroup DESCRIPTION "This group is optional and it is for voice applications only. " ::= { cdspMgmtCompliances 3 } -- units of conformance cdspMgmtGeneralInfoGroup OBJECT-GROUP OBJECTS { cdspCardIndex, cdspCardState, cdspCardResourceUtilization, cdspCardLastHiWaterUtilization, cdspCardLastResetTime, cdspOperState, cdspAlarms, cdspLastAlarmCause, cdspLastAlarmCauseText, cdspLastAlarmTime, cdspMIBEnableCardStatusNotification } STATUS current DESCRIPTION "A collection of objects providing the Digital Signal Processing related information. " ::= { cdspMgmtGroups 1 } cdspChannelGroup OBJECT-GROUP OBJECTS { cdspCardMaxChanPerDSP, cdspTotalChannels, cdspInUseChannels, cdspActiveChannels } STATUS current DESCRIPTION "A collection of objects providing information specific for multiple channels per DSP. " ::= { cdspMgmtGroups 2 } cdspMgmtExtGeneralInfoGroup OBJECT-GROUP OBJECTS { cdspTotalDsp, cdspFailedDsp, cdspCongestedDsp, cdspNormalDsp, cdspDspSwitchOverThreshold, cdspNx64Dsp, cdspDspNum } STATUS current DESCRIPTION "A collection of objects providing information for DSP. " ::= { cdspMgmtGroups 3 } cdspVoiceInfoGroup OBJECT-GROUP OBJECTS { cdspRtpSidPayloadType, cdspRtcpControl, cdspRtcpTransInterval, cdspRtcpRecvMultiplier, cdspVadAdaptive, cdspDtmfPowerLevel, cdspDtmfPowerTwist } STATUS current DESCRIPTION "A collection of objects providing DSP voice application parameters. " ::= { cdspMgmtGroups 4 } cdspMgmtNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cdspMIBCardStateNotification } STATUS current DESCRIPTION "The notifications which a DSP Management entity is required to implement." ::= { cdspMgmtGroups 5 } cdspChannelExtGroup OBJECT-GROUP OBJECTS { cdspSigBearerChannelSplit, cdspNumCongestionOccurrence, cdspXNumberOfBearerCalls, cdspXNumberOfSigCalls, cdspXAvailableBearerBandwidth, cdspXAvailableSigBandwidth } STATUS current DESCRIPTION "A collection of objects providing DSP channels splitting information. " ::= { cdspMgmtGroups 6 } END