CISCO-FRAME-RELAY-MIB device MIB details by Cisco
CISCO-FRAME-RELAY-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-FRAME-RELAY-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-FRAME-RELAY-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-------------------------------------------------------------------- -- CISCO-FRAME-RELAY-MIB.my -- Cisco Frame Relay MIB file, providing Frame Relay specific -- information that are either excluded by RFC 1315 (FR DTE MIB) -- or specific to Cisco products. -- -- January 1996, Chifei Cheng -- -- Copyright (c) 1996, 1999, 2000, 2001 by cisco Systems, Inc. -- All rights reserved. -- -------------------------------------------------------------------- -- Note: -- Until future change, it is no intention for this MIB to cover -- every Frame Relay related feature, configuration statement, or -- exec command display. The focus is to provide key information -- that are unavailable in any of the existing MIB's, but are -- currently available through the Frame Relay show commands and/or -- configuration displays. CISCO-FRAME-RELAY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, DisplayString, TruthValue FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI InterfaceIndex FROM IF-MIB ifIndex FROM RFC1213-MIB frDlcmiEntry, frCircuitEntry, frCircuitIfIndex, frCircuitDlci FROM RFC1315-MIB; -- All table indicies in this MIB that involve interface index and -- DLCI are derived from frCircuitIfIndex and frCircuitDlci -- respectively from RFC 1315. ciscoFrameRelayMIB MODULE-IDENTITY LAST-UPDATED "200010130000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-framerelay@cisco.com" DESCRIPTION "Cisco Frame Relay MIB" REVISION "200010130000Z" DESCRIPTION "(1) Added objects of FR Switching, FR Fragmentation and FR/ATM Interworking. (2) Objects for per PVC I/O rate is added to cfrExtCircuitTable" REVISION "200005220000Z" DESCRIPTION "(1) Added ELMI subgroup for ELMI objects." REVISION "200005160000Z" DESCRIPTION "(1) Added Traffic Shaping parameter objects to cfrExtCircuitTable. (2) Deprecated cfrSvcMinThruputOut and cfrSvcMinThruputIn. Added cfrExtCircuitMinThruputOut and cfrExtCircuitMinThruputIn in cfrExtCircuitTable inorder to make them applicable to both PVC/SVC. (3) Added cfrExtCircuitBandwidth object to cfrExtCircuitTable." REVISION "200004260000Z" DESCRIPTION "(1) add an integer value for cfrMapPayloadCompressType; (2) reword the Description statements for { cfrMapPayloadCompressType, cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts } so that they are not limited to software compression." REVISION "9908210000Z" DESCRIPTION "(1) Added cfrExtCircuitUncompressOuts and cfrExtCircuitUncompressIns to the circuit subgroup; (2) Added cfrMapRtpHdrCompress and cfrMapPayloadCompressType to the mapping subgroup; (3) cfrMapPayloadCompress becomes deprecated, obsoleted by cfrMapPayloadCompressType; (4) frCircuitSentOctets and frCircuitReceivedOctets per RFC1315 will reflect the number of bytes in Frame Relay frames sent to and received from the physical layer. Same effect is applied to ifOutOctets and ifInOctets as well when ifIndex refers to a Frame Relay subinterface." REVISION "9608150000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 49 } ciscoFrMIBObjects OBJECT IDENTIFIER ::= { ciscoFrameRelayMIB 1 } -- Subgroups: -- The objects include four subgroups on the topics of -- o LMI (Local Management Interface, see ANSI T1.617 Annex D and -- the Frame Relay Specification with Extensions by DEC, -- NT, StrataCom, and Cisco.), -- o Virtual circuits, -- o Circuit mapping information, -- o SVC (switched virtual circuits, see CCITT/ITU Q.933 and -- Q.922.), -- o ELMI (Enhanced Link Management Interface) objects, -- o Fragmentation objects, -- o Frame Relay/ATM Network Interworking objects, -- o Frame Relay/ATM PVC Service Interworking objects, and -- o Frame Relay Switching objects. cfrLmiObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 1 } cfrCircuitObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 2 } cfrMapObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 3 } cfrSvcObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 4 } cfrElmiObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 5 } cfrFragObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 6 } cfrConnectionObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 7 } DlciNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Numerical format of Data Link Connection Identifier (DLCI) in decimal, identical to the 'DLCI' as INTEGER of 0..DLCINumber in RFC1315. The maximum value depends on Frame Relay implementation, which is currently set to be 1023 for 2-octet address format per UNI Implementation Agreement FRF.1." SYNTAX INTEGER (0..1023) CfrMapProtocols ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Cisco link types (network protocols) that run over Frame Relay. Associated values, except for wildcard, match assigned values of internal software respectively." SYNTAX INTEGER { arp(1), serialArp(6), ip(7), xns(10), novell(11), apollo(12), vines(13), appletalk(16), ieeeSpanning(18), decnet(22), clns(25), rsrb(37), bridge(38), stun(39), frArp(40), uncompressedTcp(47), compressedTcp(48), llc2(49), frSwitch(53), dlsw(63), nhrp(74), compressedRtp(83), wildcard(999) -- either means no applicable type for -- the circuit or means point-to-point } -- LMI sub-group { cfrLmiTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay LMI information that are either supplemental to the frDlcmiTable of RFC 1315 or specific to Cisco's implementation." REFERENCE "American National Standard T1.617-1991, Annex D" ::= { cfrLmiObjs 1 } cfrLmiEntry OBJECT-TYPE SYNTAX CfrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of Frame Relay LMI over one physical interface. They are mostly FR generic and some Cisco specific." AUGMENTS { frDlcmiEntry } ::= { cfrLmiTable 1 } CfrLmiEntry ::= SEQUENCE { cfrLmiLinkstatus INTEGER, cfrLmiLinkType INTEGER, cfrLmiEnquiryIns Counter32, cfrLmiEnquiryOuts Counter32, cfrLmiStatusIns Counter32, cfrLmiStatusOuts Counter32, cfrLmiUpdateStatusIns Counter32, cfrLmiUpdateStatusOuts Counter32, cfrLmiStatusTimeouts Counter32, cfrLmiStatusEnqTimeouts Counter32, cfrLmiN392Dce INTEGER, cfrLmiN393Dce INTEGER, cfrLmiT392Dce INTEGER } -- Note: for LMI type, i.e. ANSI or Cisco, see frDlcmiState -- of RFC 1315. Also, for LMI parameters for DTE not listed here, -- e.g. T391, N391, N392, and N393, see RFC 1315. -- -- Although based on the current logic the value for -- cfrLmiDLstatus is equivalent to ifOperStatus, the object -- remains herein for future possible development change. cfrLmiLinkstatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Data link status via LMI." ::= { cfrLmiEntry 1 } cfrLmiLinkType OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), nni(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Frame Relay link type." ::= { cfrLmiEntry 2 } cfrLmiEnquiryIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages received." ::= { cfrLmiEntry 3 } cfrLmiEnquiryOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages sent." ::= { cfrLmiEntry 4 } cfrLmiStatusIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages received." ::= { cfrLmiEntry 5 } cfrLmiStatusOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages sent." ::= { cfrLmiEntry 6 } cfrLmiUpdateStatusIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Update Status messages received." ::= { cfrLmiEntry 7 } cfrLmiUpdateStatusOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Update Status messages sent" ::= { cfrLmiEntry 8 } cfrLmiStatusTimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "times" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status message" ::= { cfrLmiEntry 9 } cfrLmiStatusEnqTimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "times" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status Enquiry message" ::= { cfrLmiEntry 10 } cfrLmiN392Dce OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LMI error threshold for DCE interface. For DTE, value becomes 0." ::= { cfrLmiEntry 11 } cfrLmiN393Dce OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LMI monitored event count for DCE interface. For DTE, value becomes zero (0)." ::= { cfrLmiEntry 12 } cfrLmiT392Dce OBJECT-TYPE SYNTAX INTEGER (0..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "DCE polling verification timer for DCE interface For DTE, the value becomes zero (0)." ::= { cfrLmiEntry 13 } -- end LMI subgroup } -- Circut sub-group { cfrCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and statistics information that are generic to Frame Relay virtual circuits." ::= { cfrCircuitObjs 1 } cfrCircuitEntry OBJECT-TYPE SYNTAX CfrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay." AUGMENTS { frCircuitEntry } -- indexed by { frCircuitIfIndex, frCircuitDlci } ::= { cfrCircuitTable 1 } CfrCircuitEntry ::= SEQUENCE { cfrCircuitDEins Counter32, cfrCircuitDEouts Counter32, cfrCircuitDropPktsOuts Counter32, cfrCircuitType INTEGER } cfrCircuitDEins OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received with the Discarded Eligibility indictor (the DE bit) set." ::= { cfrCircuitEntry 1 } cfrCircuitDEouts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted with DE bit set." ::= { cfrCircuitEntry 2 } cfrCircuitDropPktsOuts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets that were to be sent." ::= { cfrCircuitEntry 3 } cfrCircuitType OBJECT-TYPE SYNTAX INTEGER { pvc(1), -- permanent virtual circuit svc(2) -- switched virtual circuit } MAX-ACCESS read-only STATUS current DESCRIPTION "Basic circuit type" ::= { cfrCircuitEntry 4 } -- Cisco specific circuit information: cfrExtCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrExtCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315." ::= { cfrCircuitObjs 2 } cfrExtCircuitEntry OBJECT-TYPE SYNTAX CfrExtCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a Frame Relay virtual circuit that are specific to Cisco implementation." AUGMENTS { frCircuitEntry } -- indexed by { frCircuitIfIndex, frCircuitDlci } ::= { cfrExtCircuitTable 1 } CfrExtCircuitEntry ::= SEQUENCE { cfrExtCircuitIfName DisplayString, cfrExtCircuitIfType INTEGER, cfrExtCircuitSubifIndex InterfaceIndex, cfrExtCircuitMapStatus INTEGER, cfrExtCircuitCreateType INTEGER, cfrExtCircuitMulticast TruthValue, cfrExtCircuitRoutedDlci DlciNumber, cfrExtCircuitRoutedIf InterfaceIndex, cfrExtCircuitUncompressIns Counter32, cfrExtCircuitUncompressOuts Counter32, cfrExtCircuitFECNOuts Counter32, cfrExtCircuitBECNOuts Counter32, cfrExtCircuitMinThruputOut Integer32, cfrExtCircuitMinThruputIn Integer32, cfrExtCircuitBcastPktOuts Counter32, cfrExtCircuitBcastByteOuts Counter32, cfrExtCircuitBandwidth Integer32, cfrExtCircuitShapeByteLimit Integer32, cfrExtCircuitShapeInterval Integer32, cfrExtCircuitShapeByteIncrement Integer32, cfrExtCircuitShapePkts Counter32, cfrExtCircuitShapeBytes Counter32, cfrExtCircuitShapePktsDelay Counter32, cfrExtCircuitShapeBytesDelay Counter32, cfrExtCircuitShapeActive TruthValue, cfrExtCircuitShapeAdapting INTEGER, cfrExtCircuitTxDataRate INTEGER, cfrExtCircuitTxPktRate INTEGER, cfrExtCircuitRcvDataRate INTEGER, cfrExtCircuitRcvPktRate INTEGER } cfrExtCircuitIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of the main interface or the subinterface that this DLCI is associated with. This is the same name string of an interface used in the configuration and all console displays, such as 'serial 0', 'serial 3/0.3', etc." ::= { cfrExtCircuitEntry 1 } cfrExtCircuitIfType OBJECT-TYPE SYNTAX INTEGER { mainInterface(1), pointToPoint(2), -- subinterface multipoint(3) -- subinterface } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the subinterface this DLCI is associated with, if configured." ::= { cfrExtCircuitEntry 2 } cfrExtCircuitSubifIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "For value greater than zero (0), it indicates the network management interface index for the subinterface associated with this DLCI. Value 0 means the DLCI is not associated with any subinterface." ::= { cfrExtCircuitEntry 3 } cfrExtCircuitMapStatus OBJECT-TYPE SYNTAX INTEGER (0..2047) MAX-ACCESS read-only STATUS current DESCRIPTION "The mapping protocols (internally considered as the 'link type') applied on this circuit. The value ranges from 0 to 2047. For point-to-point DLCI, the value stays zero. Otherwise, the value is a sum. It initially takes the value zero, then, for each type of Protocol, 2 raised to a power is added to the sum. The following table presents respective power and equivalent value for each applicable type: Protocol Power Value -------- ----- ----- IP 0 1 IPX 1 2 Appletalk 2 4 XNS 3 8 VINES 4 16 DECnet 5 32 CLNS 6 64 Bridging 7 128 RSRB 8 256 STUN 9 512 LLC2 10 1024 For example, value 3 means the circuit's mapping protocols include IP and IPX. (3 = 2**1 + 2**0, where 0 corresponds to IP and 1 to IPX.) Value 0 means there is currently no mapping protocol for the circuit. See cfrMapTable for more mapping information." ::= { cfrExtCircuitEntry 4 } cfrExtCircuitCreateType OBJECT-TYPE SYNTAX INTEGER { dynamic(1), -- PVC established through LMI -- or an SVC established through -- SVC signalling static(2) -- circuit was configured } MAX-ACCESS read-only STATUS current DESCRIPTION "Identify the last source of the circuit's creation." ::= { cfrExtCircuitEntry 5 } cfrExtCircuitMulticast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if this DLCI is a multicast DLCI." ::= { cfrExtCircuitEntry 6 } cfrExtCircuitRoutedDlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The routed DLCI to pair up with this DLCI for switching function. NOTE: Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { cfrExtCircuitEntry 7 } cfrExtCircuitRoutedIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface for the routed DLCI that pairs up with this DLCI for switching. Value greater than 0 is the InterfaceIndex for that interface. Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { cfrExtCircuitEntry 8 } cfrExtCircuitUncompressIns OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of inbound octets of the data packets, accounted at Frame Relay level after FRF.9 payload decompression is applied. In the case of non-FRF.9, this value could be identical to frCircuitReceivedOctets, unless otherwise noted." ::= { cfrExtCircuitEntry 9 } cfrExtCircuitUncompressOuts OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of outbound octets of the data packets, accounted at Frame Relay level before FRF.9 payload compression is applied. In the case of non-FRF.9, this value could be identical to frCircuitSentOctets, unless otherwise noted." ::= { cfrExtCircuitEntry 10 } cfrExtCircuitFECNOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames sent out to the network indicating forward congestion." ::= { cfrExtCircuitEntry 11 } cfrExtCircuitBECNOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames sent out to the network indicating backward congestion." ::= { cfrExtCircuitEntry 12 } cfrExtCircuitMinThruputOut OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's outgoing minimal Throughput based on configuration." ::= { cfrExtCircuitEntry 13 } cfrExtCircuitMinThruputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming minimal Throughput based on configuration." ::= { cfrExtCircuitEntry 14 } cfrExtCircuitBcastPktOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of broadcast packets sent out to the network." ::= { cfrExtCircuitEntry 15 } cfrExtCircuitBcastByteOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes sent out to the network in broadcast packets." ::= { cfrExtCircuitEntry 16 } cfrExtCircuitBandwidth OBJECT-TYPE SYNTAX Integer32 (0..16777215) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Bandwidth of the virtual circuit, acquired from Cisco typed LMI Full Status message." ::= { cfrExtCircuitEntry 17 } cfrExtCircuitShapeByteLimit OBJECT-TYPE SYNTAX Integer32 (125..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of tokens a token bucket can hold in any time interval in case of traffic shaping." ::= { cfrExtCircuitEntry 18 } cfrExtCircuitShapeInterval OBJECT-TYPE SYNTAX Integer32 (10..125) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Committed rate measurement interval." ::= { cfrExtCircuitEntry 19 } cfrExtCircuitShapeByteIncrement OBJECT-TYPE SYNTAX Integer32 (125..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tokens added into the token bucket per time interval in case of traffic shaping." ::= { cfrExtCircuitEntry 20 } cfrExtCircuitShapePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets that went through traffic shaping." ::= { cfrExtCircuitEntry 21 } cfrExtCircuitShapeBytes OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that went through traffic shaping." ::= { cfrExtCircuitEntry 22 } cfrExtCircuitShapePktsDelay OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets that were delayed by the traffic shaper." ::= { cfrExtCircuitEntry 23 } cfrExtCircuitShapeBytesDelay OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that were delayed by the traffic shaper." ::= { cfrExtCircuitEntry 24 } cfrExtCircuitShapeActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether shaping is active or not." ::= { cfrExtCircuitEntry 25 } cfrExtCircuitShapeAdapting OBJECT-TYPE SYNTAX INTEGER { none(1), becn(2), foreSight(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of Adaptive Shaping configured. none(1) - No adaptive shaping configured becn(2) - Backward Explicit Congestion Notification foreSight(3) - ForeSight is the network traffic control software used in Cisco WAN switches" ::= { cfrExtCircuitEntry 26 } cfrExtCircuitTxDataRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average rate (bytes/second) at which data is transmitted in this circuit. " ::= { cfrExtCircuitEntry 27 } cfrExtCircuitTxPktRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average number of packets sent in a second in this circuit." ::= { cfrExtCircuitEntry 28 } cfrExtCircuitRcvDataRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average rate (bytes/second) at which data is received in this circuit. " ::= { cfrExtCircuitEntry 29 } cfrExtCircuitRcvPktRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average number of packets received in a second in this circuit. " ::= { cfrExtCircuitEntry 30 } -- end circuit subgroup } -- Mapping sub-group { cfrMapTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of protocols and addresses mapping information of FR virtual circuit." ::= { cfrMapObjs 1 } cfrMapEntry OBJECT-TYPE SYNTAX CfrMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains one mapping information of a Frame Relay virtual circuit." INDEX { frCircuitIfIndex, frCircuitDlci, cfrMapIndex } ::= { cfrMapTable 1 } CfrMapEntry ::= SEQUENCE { cfrMapIndex INTEGER, cfrMapProtocol CfrMapProtocols, cfrMapAddress OCTET STRING (SIZE(0..64)), cfrMapType INTEGER, cfrMapEncaps INTEGER, cfrMapBroadcast TruthValue, cfrMapPayloadCompress TruthValue, cfrMapTcpHdrCompress INTEGER, cfrMapRtpHdrCompress INTEGER, cfrMapPayloadCompressType INTEGER } cfrMapIndex OBJECT-TYPE SYNTAX INTEGER (1..999) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary Index to the mapping information associated with a certain circuit. The maximum value is arbitrarily picked which is considered sufficient for usual configuration." ::= { cfrMapEntry 1 } cfrMapProtocol OBJECT-TYPE SYNTAX CfrMapProtocols MAX-ACCESS read-only STATUS current DESCRIPTION "Mapping protocol for this circuit." ::= { cfrMapEntry 2 } cfrMapAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Mapping protocol address at remote end for this DLCI. NOTE: For point-to-point DLCI, the string is fixed to be point-to-point." ::= { cfrMapEntry 3 } cfrMapType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), svc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type for the map creation." ::= { cfrMapEntry 4 } cfrMapEncaps OBJECT-TYPE SYNTAX INTEGER { ietf(1), -- following IETF specifications -- (RFC 1490 as up to date) cisco(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indication of the encapsulation type for this mapping protocol." ::= { cfrMapEntry 5 } cfrMapBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcast enabled or disabled." ::= { cfrMapEntry 6 } cfrMapPayloadCompress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated -- obsoleted by cfrMapPayloadCompressType DESCRIPTION "Indicate if payload compression is enabled." ::= { cfrMapEntry 7 } cfrMapTcpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "TCP header compression type, if applicable." ::= { cfrMapEntry 8 } cfrMapRtpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RTP header compression type, if applicable. The value 'passive' means that the header of an outgoing RTP/IP packet is compressed only if an incoming RTP/IP packet had a compressed header. The value 'active' means the header of every outgoing RTP/IP packet is compressed." ::= { cfrMapEntry 9 } cfrMapPayloadCompressType OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), cisco(2), -- Cisco proprietary FR packet- -- by-packet payload compression frf9Software(3), -- FRF.9 software payload compression frf9Hardware(4) -- FRF.9 hardware payload compression } MAX-ACCESS read-only STATUS current DESCRIPTION "FR payload compression type, if applicable. FRF.9 is the Frame Relay Forum Implementation Agreement on FR payload compression. The compression can be done by either software or hardware (when equipped with the supporting hardware), depending on configuration." REFERENCE "Frame Relay Forum document number FRF.9" ::= { cfrMapEntry 10 } -- end mapping subgroup } -- SVC sub-group { -- containing SVC spcific information cfrSvcTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of FR SVC specific, descriptive and statistics information." ::= { cfrSvcObjs 1 } cfrSvcEntry OBJECT-TYPE SYNTAX CfrSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains circuit information specific to a Frame Relay Switched Virtual Circuit." INDEX { frCircuitIfIndex, frCircuitDlci } ::= { cfrSvcTable 1 } CfrSvcEntry ::= SEQUENCE { cfrSvcAddrLocal OCTET STRING (SIZE(0..64)), cfrSvcAddrRemote OCTET STRING (SIZE(0..64)), cfrSvcThroughputIn Integer32, cfrSvcMinThruputOut Integer32, cfrSvcMinThruputIn Integer32, cfrSvcCommitBurstIn Integer32, cfrSvcExcessBurstIn Integer32, cfrSvcIdleTime Integer32 } -- For circuit (DLCI) outbound throughput and outbound Committed -- and Excess Burst size, please refer to the following from -- RFC1315 respectively: -- frCircuitThroughput, -- frCircuitCommittedBurst, and -- frCircuitExcessBurst cfrSvcAddrLocal OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local E.164/X.125 address for the circuit." ::= { cfrSvcEntry 1 } cfrSvcAddrRemote OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote E.164/X.125 address for the circuit." ::= { cfrSvcEntry 2 } cfrSvcThroughputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming throughput. For outgoing throughput (commonly referred to as CIR) see frCircuitThroughput per RFC1315." ::= { cfrSvcEntry 3 } cfrSvcMinThruputOut OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS deprecated -- deprecated by -- cfrExtCircuitMinThruputOut DESCRIPTION "Circuit's outgoing minimal Throughput." ::= { cfrSvcEntry 4 } cfrSvcMinThruputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS deprecated -- deprecated by -- cfrExtCircuitMinThruputIn DESCRIPTION "Circuit's incoming minimal Throughput." ::= { cfrSvcEntry 5 } cfrSvcCommitBurstIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming Committed Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing CBR, see frCircuitCommittedBurst per RFC 1315." ::= { cfrSvcEntry 6 } cfrSvcExcessBurstIn OBJECT-TYPE SYNTAX Integer32 (9600..2440000) MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming Excess Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing EBR, see frCircuitExcessBurst per RFC 1315." ::= { cfrSvcEntry 7 } cfrSvcIdleTime OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's idle time period. If expires, the circuit is cleared." ::= { cfrSvcEntry 8 } -- end SVC subgroup } -- Enhanced Link Management Interface(ELMI) sub-group { -- ELMI is the protocol that learns QOS parameters(CIR,Bc,Be etc) -- of a VC from the switch. -- This sub group contains ELMI specific information. cfrElmiIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Management address of the device used for address registration. Network management station can send management messages to this IP address. This can be user configured address or the address of one of the interfaces on the device. If address registration is disabled then this will have a value of 0.0.0.0. This object is accessible only if the ELMI protocol is supported on the device" ::= { cfrElmiObjs 1 } cfrElmiTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrElmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of CISCO Frame Relay ELMI information that is specific to CISCO implementation" ::= { cfrElmiObjs 2 } cfrElmiEntry OBJECT-TYPE SYNTAX CfrElmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information about a physical interface. The table can be accessible only if the device supports ELMI protocol and if LMI is enabled on the interface." INDEX { ifIndex } ::= { cfrElmiTable 1 } CfrElmiEntry ::= SEQUENCE { cfrElmiLinkStatus INTEGER, cfrElmiArStatus INTEGER, cfrElmiRemoteStatus INTEGER } cfrElmiLinkStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states whether Enhanced Link Management Interface(ELMI) protocol is enabled or not on a frame relay interface." ::= { cfrElmiEntry 1 } cfrElmiArStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states whether the Enhanced Link Management Interface(ELMI) address registration(AR) mechanism is enabled or not on a frame relay interface. A value of 1 indicates ELMI AR is supported on the interface. A value of 2 indicates ELMI AR is supported but the user disabled the exchange of IP address and ifIndex with the neighboring device. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface." ::= { cfrElmiEntry 2 } cfrElmiRemoteStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states the Enhanced Link Management(ELMI) status on the other end of the interface. If cfrElmiLinkStatus is enabled on the other end a value of 1 will be returned, else 2 will be returned. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface" ::= { cfrElmiEntry 3 } cfrElmiNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrElmiNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of CISCO Frame Relay Neighbor ELMI information that is specific to CISCO implementation." ::= { cfrElmiObjs 3 } cfrElmiNeighborEntry OBJECT-TYPE SYNTAX CfrElmiNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of the neighboring device connected to a physical interface. The entry will be present only if ELMI is enabled on the neighboring device interface. If the value of the cfrElmiRemoteStatus in the cfrElmiEntry is 1 then a valid entry exists for the interface. If ELMI is not supported on the remote end then, the neighbor information for the interface will not be present" INDEX { ifIndex } ::= { cfrElmiNeighborTable 1 } CfrElmiNeighborEntry ::= SEQUENCE { cfrElmiNeighborArStatus INTEGER, cfrElmiNeighborIpAddress IpAddress, cfrElmiNeighborIfIndex InterfaceIndex, cfrElmiNeighborVendorName DisplayString, cfrElmiNeighborPlatformName DisplayString, cfrElmiNeighborDeviceName DisplayString } cfrElmiNeighborArStatus OBJECT-TYPE SYNTAX INTEGER { notsupported(1), enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of ELMI Address registration(AR) on the neighboring device. A value of 1 indicates ELMI AR is not supported on the neighboring device. A value of 2 indicates ELMI AR is enabled on the interface. A value of 3 indicates AR is supported, but user disabled the exchange of IP address and ifIndex with the neighbor." ::= { cfrElmiNeighborEntry 1 } cfrElmiNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Management IP address of the neighboring device to which the other end of this interface is connected. Network management system can use this address to send management messages to the device. If address registration is not supported on the remote end then the value will be 0.0.0.0. NMS uses this object in the topology discovery of the network." ::= { cfrElmiNeighborEntry 2 } cfrElmiNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The Interface index of the neighboring device to which this interface is connected. If the value of cfrElmiNeighborArStatus is 2 then this will have a valid value. If the value of cfrElmiNeighborArStatus is 3 or 1 then value of this object will be 0. NMS uses this object in the topology discovery of the network." ::= { cfrElmiNeighborEntry 3 } cfrElmiNeighborVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 4 } cfrElmiNeighborPlatformName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Platform name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 5 } cfrElmiNeighborDeviceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 6 } -- end ELMI sub-group } -- Fragmentation sub-group { cfrFragTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrFragEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay Fragmentation information. These are specific to Cisco's implementation." ::= { cfrFragObjs 1 } cfrFragEntry OBJECT-TYPE SYNTAX CfrFragEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains details of fragmentation configured on this circuit. " INDEX { frCircuitIfIndex, frCircuitDlci} ::= { cfrFragTable 1 } CfrFragEntry ::= SEQUENCE { cfrFragSize INTEGER, cfrFragType DisplayString, cfrFragInPkts Counter32, cfrFragOutPkts Counter32, cfrFragInOctets Counter32, cfrFragOutOctets Counter32, cfrFragNotInPkts Counter32, cfrFragNotOutPkts Counter32, cfrFragNotInOctets Counter32, cfrFragNotOutOctets Counter32, cfrFragAssembledInPkts Counter32, cfrFragAssembledInOctets Counter32, cfrFragPreOutPkts Counter32, cfrFragPreOutOctets Counter32, cfrFragDroppedReAssembledInPkts Counter32, cfrFragDroppedFragmentedOutPkts Counter32, cfrFragTimeoutsIn INTEGER, cfrFragOutOfSeqFragPkts Counter32, cfrFragUnexpectedBBitSetPkts Counter32, cfrFragSeqMissedPkts Counter32, cfrFragInterleavedOutPkts Counter32 } cfrFragSize OBJECT-TYPE SYNTAX INTEGER (16..1600) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "cfrFragSize defines the payload size of a fragment and it excludes the FR headers and any FR fragmentation header." ::= { cfrFragEntry 1 } cfrFragType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Fragmentation type configured by the user. The types supported are end-to-end, VoFR-cisco and VoFR." ::= { cfrFragEntry 2 } cfrFragInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames received that have a fragmentation header." ::= { cfrFragEntry 3 } cfrFragOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of fragments that are transmitted with a fragmenation header." ::= { cfrFragEntry 4 } cfrFragInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in frames that have a fragmentation header. The number of bytes include the FR header." ::= { cfrFragEntry 5} cfrFragOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that are transmitted in frames with a fragmenation header. The number of bytes also includes the FR header." ::= { cfrFragEntry 6} cfrFragNotInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames received that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 7} cfrFragNotOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames transmitted without fragmenting and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 8} cfrFragNotInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in frames that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 9} cfrFragNotOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes transmitted in frames that are not fragmented and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 10} cfrFragAssembledInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 11} cfrFragAssembledInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e.in un-fragmentated pkts)." ::= { cfrFragEntry 12} cfrFragPreOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames fragmented and trasmitted. It also counts the number of packets trasmitted without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 13} cfrFragPreOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes transmitted in fragmented frames. It also counts the number of bytes trasmitted in frames without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 14} cfrFragDroppedReAssembledInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received fragments dropped for reasons such as : running out of memory, receiving segments out of sequence, receiving an unexpected frame with a B bit set, timing out on a reassembling frame." ::= { cfrFragEntry 15} cfrFragDroppedFragmentedOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments dropped because of running out of memory." ::= { cfrFragEntry 16} cfrFragTimeoutsIn OBJECT-TYPE SYNTAX INTEGER (0..1000) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of reassemble timer timeouts for this circuit. A frame requiring more than two minutes to fully reassemble is dropped and timeout will be incremented by one." ::= { cfrFragEntry 17} cfrFragOutOfSeqFragPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of packets received with an unexpected sequence number. All fragments being reassembled are dropped. Start a new packet with the received segment only if the B bit is set on the segment. Otherwise the new segment is also dropped." ::= { cfrFragEntry 18} cfrFragUnexpectedBBitSetPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received in this circuit with a B bit set. All fragments being reassembled are dropped and a new packet is started with this segment." ::= { cfrFragEntry 19} cfrFragSeqMissedPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received in this circuit with skipped sequence number." ::= { cfrFragEntry 20} cfrFragInterleavedOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets that have been interleaved between segments." ::= { cfrFragEntry 21} -- end Fragmentation sub-group } -- Connect sub-group { cfrConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking connection information. These are specific to Cisco's implementation." ::= { cfrConnectionObjs 1 } cfrConnectionEntry OBJECT-TYPE SYNTAX CfrConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a connection that is established for Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking." INDEX { frCircuitIfIndex, frCircuitDlci} ::= { cfrConnectionTable 1 } CfrConnectionEntry ::= SEQUENCE { cfrConnName DisplayString, cfrConnID INTEGER, cfrConnState DisplayString, cfrConnSegment1Name DisplayString, cfrConnSegment1VCGroup DisplayString, cfrConnSegment1Dlci DlciNumber, cfrConnSegment2Name DisplayString, cfrConnSegment2Vpi INTEGER, cfrConnSegment2Vci INTEGER, cfrConnServiceTranslation INTEGER, cfrConnFrSscsDlci DlciNumber, cfrConnEfciBit INTEGER, cfrConnDeBit INTEGER, cfrConnClpBit INTEGER } cfrConnName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of a for FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 1 } cfrConnID OBJECT-TYPE SYNTAX INTEGER (1..2000) MAX-ACCESS read-only STATUS current DESCRIPTION "The numerical identifier of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 2 } cfrConnState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Status of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 3} cfrConnSegment1Name OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name used to identify the first segment of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 4} cfrConnSegment1VCGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name used to identify the VC-Group in the first segment of a Frame Relay/ATM Network Interworking (FRF.5)connection. This field is not applicabe in case of, FRF.8 (Frame Relay/ATM Service Interworking) and FR-FR connectione. " ::= { cfrConnectionEntry 5} cfrConnSegment1Dlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI used as the first segment of a FR-FR or FR-ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 6} cfrConnSegment2Name OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The interface on which second segment of a FR-FR or FR-ATM Network/Service Interworking connection is configured." ::= { cfrConnectionEntry 7} cfrConnSegment2Vpi OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of VPI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, the same will be used to display the DLCI used as the second segment." ::= { cfrConnectionEntry 8} cfrConnSegment2Vci OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of VCI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, this is not supported." ::= { cfrConnectionEntry 9} cfrConnServiceTranslation OBJECT-TYPE SYNTAX INTEGER { serviceTranslationEnabled(1), serviceTranslationNotEnabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether Service Translation Mode is supported or not. Translation Mode is the interworking of internetworking (routed and/or bridged) protocols used in FR-ATM Service PVC Interworking(FRF.8). This is not supported in case of FRF.5 (FR-ATM network Interworking) and FR-FR connections." ::= { cfrConnectionEntry 10} cfrConnFrSscsDlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI value used at the FR-SSCS layer. This is one of connection multiplexing methods used in Frame Relay/ATM Network Interworking. Not supported in case of FRF.8 (FR-ATM Service PVC Interworking) and FR-FR connections" ::= { cfrConnectionEntry 11} cfrConnEfciBit OBJECT-TYPE SYNTAX INTEGER { mapFecn(1), notMapFecn(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether the FECN field in the FR frame is mapped to the ATM EFCI field of every cell generated out of the FR frame. This is used to indicate congestion in FR to ATM direction in case of Frame Relay/ATM Service PVC Interworking. Not supported in FRF.5 (Frame Relay/ATM Network Interworking and FR-FR connections." ::= { cfrConnectionEntry 12} cfrConnDeBit OBJECT-TYPE SYNTAX INTEGER { noMapClp(1), mapClp(2), setDe0(3), setDe1(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The method of operation for loss priority mapping in the B-ISDN to FR direction.. Not supported in case of FR-FR connection." ::= { cfrConnectionEntry 13} cfrConnClpBit OBJECT-TYPE SYNTAX INTEGER { setClpTo0AndCopyDeToFrsscsDe(1), setClpTo1AndCopyDeToFrsscsDe(2), copyDeToFrsscsDeAndClp(3), copyDeToClp(4), setClp1(5), setClp0(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The method of operation used to map loss priority mapping in the FR to ATM direction. Not supported in case of FR-FR connection." ::= { cfrConnectionEntry 14} -- end Conn subgroup } ciscoFrMIBConformance OBJECT IDENTIFIER ::= { ciscoFrameRelayMIB 3 } ciscoFrMIBCompliances OBJECT IDENTIFIER ::= { ciscoFrMIBConformance 1 } ciscoFrMIBGroups OBJECT IDENTIFIER ::= { ciscoFrMIBConformance 2 } ciscoFrMIBCompliance MODULE-COMPLIANCE STATUS obsolete -- obsoleted by ciscoFrMIBCompliancesRev2 DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { ciscoFrMIBGroup } ::= { ciscoFrMIBCompliances 1 } ciscoFrMIBCompliancesRev1 MODULE-COMPLIANCE STATUS obsolete -- obsoleted by ciscoFrMIBCompliancesRev2 DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { ciscoFrMIBGroupRev1 } ::= { ciscoFrMIBCompliances 2 } ciscoFrMIBCompliancesRev2 MODULE-COMPLIANCE STATUS obsolete -- obsoleted by ciscoFrMIBCompliancesRev3 DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { ciscoFrLmiMIBGroup, ciscoFrCircuitMIBGroup, ciscoExtCircuitMIBGroup, ciscoFrTsMIBGroup, ciscoFrMapMIBGroup, ciscoFrSvcMIBGroup } ::= { ciscoFrMIBCompliances 3 } ciscoFrMIBCompliancesRev3 MODULE-COMPLIANCE STATUS deprecated -- deprecated by ciscoFrMIBCompliancesRev4 DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { ciscoFrLmiMIBGroup, ciscoFrCircuitMIBGroup, ciscoExtCircuitMIBGroup, ciscoFrTsMIBGroup, ciscoFrMapMIBGroup, ciscoFrSvcMIBGroup, ciscoFrElmiMIBGroup} ::= { ciscoFrMIBCompliances 4 } ciscoFrMIBCompliancesRev4 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { ciscoFrLmiMIBGroup, ciscoFrCircuitMIBGroup, ciscoExtCircuitMIBGroup1, ciscoFrTsMIBGroup, ciscoFrMapMIBGroup, ciscoFrSvcMIBGroup, ciscoFrElmiMIBGroup1, ciscoFrFragMIBGroup, ciscoFrConnMIBGroup} ::= { ciscoFrMIBCompliances 5 } -- units of conformance: ciscoFrMIBGroup OBJECT-GROUP OBJECTS { cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, cfrLmiN393Dce, cfrLmiT392Dce, cfrCircuitDEins, cfrCircuitDEouts, cfrCircuitDropPktsOuts, cfrCircuitType, cfrExtCircuitIfName, cfrExtCircuitIfType, cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, cfrExtCircuitCreateType, cfrExtCircuitMulticast, cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, cfrMapIndex, cfrMapProtocol, cfrMapAddress, cfrMapType, cfrMapEncaps, cfrMapBroadcast, cfrMapPayloadCompress, cfrMapTcpHdrCompress, cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, cfrSvcMinThruputOut, cfrSvcMinThruputIn, cfrSvcCommitBurstIn, cfrSvcExcessBurstIn, cfrSvcIdleTime } STATUS deprecated -- obsoleted by ciscoFrMIBGroupRev1 DESCRIPTION "The compliance statement for entities which implement this Cisco Frame Relay MIB." ::= { ciscoFrMIBGroups 1 } ciscoFrMIBGroupRev1 OBJECT-GROUP OBJECTS { cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, cfrLmiN393Dce, cfrLmiT392Dce, cfrCircuitDEins, cfrCircuitDEouts, cfrCircuitDropPktsOuts, cfrCircuitType, cfrExtCircuitIfName, cfrExtCircuitIfType, cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, cfrExtCircuitCreateType, cfrExtCircuitMulticast, cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, cfrMapIndex, cfrMapProtocol, cfrMapAddress, cfrMapType, cfrMapEncaps, cfrMapBroadcast, -- removed cfrMapPayloadCompress, obsoleted by cfrMapPayloadCompressType cfrMapTcpHdrCompress, cfrMapRtpHdrCompress, cfrMapPayloadCompressType, cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, cfrSvcMinThruputOut, cfrSvcMinThruputIn, cfrSvcCommitBurstIn, cfrSvcExcessBurstIn, cfrSvcIdleTime } STATUS deprecated DESCRIPTION "A collection of objects providing router's Frame Relay configuration and statistics information that are additional to the IETF standard Frame Relay DTE MIB." ::= { ciscoFrMIBGroups 2 } ciscoFrLmiMIBGroup OBJECT-GROUP OBJECTS { cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, cfrLmiN393Dce, cfrLmiT392Dce } STATUS current DESCRIPTION "A collection of objects providing router's Frame Relay LMI configuration and statistics information either supplemental to the frDlcmiTable of RFC 1315 or specific to Cisco's implementation." ::= { ciscoFrMIBGroups 3 } ciscoFrCircuitMIBGroup OBJECT-GROUP OBJECTS { cfrCircuitDEins, cfrCircuitDEouts, cfrCircuitDropPktsOuts, cfrCircuitType } STATUS current DESCRIPTION "A collection of objects providing information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay." ::= { ciscoFrMIBGroups 4 } ciscoExtCircuitMIBGroup OBJECT-GROUP OBJECTS { cfrExtCircuitIfName, cfrExtCircuitIfType, cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, cfrExtCircuitCreateType, cfrExtCircuitMulticast, cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts, cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn, cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts, cfrExtCircuitBandwidth } STATUS deprecated DESCRIPTION "A collection of objects that provide Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315." ::= { ciscoFrMIBGroups 5 } ciscoExtCircuitMIBGroup1 OBJECT-GROUP OBJECTS { cfrExtCircuitIfName, cfrExtCircuitIfType, cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, cfrExtCircuitCreateType, cfrExtCircuitMulticast, cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts, cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn, cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts, cfrExtCircuitBandwidth, cfrExtCircuitTxDataRate, cfrExtCircuitTxPktRate, cfrExtCircuitRcvDataRate, cfrExtCircuitRcvPktRate } STATUS current DESCRIPTION "A collection of objects that provide Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315." ::= { ciscoFrMIBGroups 13 } ciscoFrTsMIBGroup OBJECT-GROUP OBJECTS { cfrExtCircuitShapeByteLimit, cfrExtCircuitShapeInterval, cfrExtCircuitShapeByteIncrement, cfrExtCircuitShapePkts, cfrExtCircuitShapeBytes, cfrExtCircuitShapePktsDelay, cfrExtCircuitShapeBytesDelay, cfrExtCircuitShapeActive, cfrExtCircuitShapeAdapting } STATUS current DESCRIPTION "A collection of objects that provide information about Frame Relay Traffic Shaping. These are additional to the IETF standard Frame Relay DTE MIB." ::= { ciscoFrMIBGroups 6 } ciscoFrMapMIBGroup OBJECT-GROUP OBJECTS { cfrMapIndex, cfrMapProtocol, cfrMapAddress, cfrMapType, cfrMapEncaps, cfrMapBroadcast, cfrMapTcpHdrCompress, cfrMapRtpHdrCompress, cfrMapPayloadCompressType } STATUS current DESCRIPTION "A collection of objects to provide mapping information of a Frame Relay virtual circuit. These are additional to the IETF standard Frame Relay DTE MIB." ::= { ciscoFrMIBGroups 7 } ciscoFrSvcMIBGroup OBJECT-GROUP OBJECTS { cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, cfrSvcCommitBurstIn, cfrSvcExcessBurstIn, cfrSvcIdleTime } STATUS current DESCRIPTION "A collection of objects to provide circuit information specific to a Frame Relay Switched Virtual Circuit.This is in addition to the IETF standard Frame Relay DTE MIB." ::= { ciscoFrMIBGroups 8 } ciscoFrElmiMIBGroup OBJECT-GROUP OBJECTS { cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus, cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress, cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName, cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName } STATUS deprecated DESCRIPTION "A collection of objects providing router's ELMI information." ::= { ciscoFrMIBGroups 9 } ciscoFrElmiMIBGroup1 OBJECT-GROUP OBJECTS { cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus, cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress, cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName, cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName, cfrElmiLinkStatus } STATUS current DESCRIPTION "A collection of objects providing router's ELMI information." ::= { ciscoFrMIBGroups 10 } ciscoFrFragMIBGroup OBJECT-GROUP OBJECTS { cfrFragSize, cfrFragType, cfrFragInPkts, cfrFragOutPkts, cfrFragInOctets, cfrFragOutOctets, cfrFragNotInPkts, cfrFragNotOutPkts, cfrFragNotInOctets, cfrFragNotOutOctets, cfrFragAssembledInPkts, cfrFragAssembledInOctets, cfrFragPreOutPkts, cfrFragPreOutOctets, cfrFragDroppedReAssembledInPkts, cfrFragDroppedFragmentedOutPkts, cfrFragTimeoutsIn, cfrFragOutOfSeqFragPkts, cfrFragUnexpectedBBitSetPkts, cfrFragSeqMissedPkts, cfrFragInterleavedOutPkts } STATUS current DESCRIPTION "A collection of objects providing router's fragmentation information." ::= { ciscoFrMIBGroups 11 } ciscoFrConnMIBGroup OBJECT-GROUP OBJECTS { cfrConnName, cfrConnID, cfrConnState, cfrConnSegment1Name, cfrConnSegment1VCGroup, cfrConnSegment1Dlci, cfrConnSegment2Name, cfrConnSegment2Vpi, cfrConnSegment2Vci, cfrConnServiceTranslation, cfrConnFrSscsDlci, cfrConnEfciBit, cfrConnDeBit, cfrConnClpBit } STATUS current DESCRIPTION "A collection of objects providing router's fragmentation information." ::= { ciscoFrMIBGroups 12 } END