CISCO-ITP-RT-MIB device MIB details by Cisco
CISCO-ITP-RT-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-ITP-RT-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-ITP-RT-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- ***************************************************************** -- CISCO-ITP-RT-MIB: Itp Signalling Point Routing Table -- -- August 2001, John Linton, Shekhar Acharya -- -- Copyright (c) 2001, 2002, 2003 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** -- -- ***************************************************************** CISCO-ITP-RT-MIB DEFINITIONS ::= BEGIN IMPORTS Counter32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI TimeStamp, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF CItpTcLinksetId, CItpTcPointCode, CItpTcQos, CItpTcRouteTableName, CItpTcTableLoadStatus FROM CISCO-ITP-TC-MIB ciscoMgmt FROM CISCO-SMI; ciscoItpRtMIB MODULE-IDENTITY LAST-UPDATED "200307100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-ss7s@cisco.com" DESCRIPTION "This MIB is for managing information required to route messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides the functions necessary to act as a SS7 signalling point. Each signalling point is connected to other signalling point using IP based or traditional TDM links. The relevant ITU documents describing this technology are the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. Definitions and overview: Route: A route consists of one or more linksets used to transport MTP3 Message Signal Units(MSU) between signalling points. A route is an association between a destination point code(DPC) and a linkset, i.e., a linkset that can be used to send an MSU to the given DPC. Routeset: A routeset is a set of routes to a given DPC. Each route within a routeset is on a possible path toward the DPC. Each route within the routeset has associated with it a route priority. In the following simple configuration, two routes exist that can be used to transport MSUs from STP1 to STP4. --------- STP1-STP2 --------- - STP1 ----------------------------- STP2 - --------- --------- | | | STP1-STP3 STP2-STP4 | | | --------- STP3-STP4 --------- - STP3 ----------------------------- STP4 - --------- --------- Routeset on STP1 for DPC = STP4: STP1-STP2, STP1-STP3 Linkset: A linkset is a set of signalling links connecting two signalling points. Combined Linkset: Two linksets with equal number of links and capacity that form routes of equal priority to a given DPC are called Combined Linksets. It is primarily used for load sharing and redundancy. In the following, example, linksets 'SSP1-STP1' and 'SSP1-STP2' form a combined linsket. SSP1-STP1 --------- |------------------------- STP1 - | --------- - - - - - SSP1 - - - - - | SSP1-STP2 --------- |------------------------ STP2 - --------- Routing: The routing of SS7 Message signalling Units(MSU) is based on the DPC. Message Signalling Units are sent from an originating point code(OPC) to DPC. Each MSU will traverse one or more linksets as it is routed to its final destination. When an MSU arrives at a signalling point and the DPC does not match the signalling point's point code the MSU must be directed toward the DPC. Each signalling point has enough routing information to determine which linkset should be used to transmit the MSU toward its final destination. Route statement: Each ITP Signalling Point has route statements needed to determine which linkset should be used to transmit message signalling units to destinations. Each route statement consists of a destination, a priority and a linkset name. The destination is specified as a combination of DPC and mask. The priority, also know as cost, is used to define the order in which the routes are selected. The linkset name specifies which linkset to use to reach the destination. Route table: Each ITP Signalling Point has a table of routes. These route entries are used to determine which linkset should be selected to transmit message signalling units to a given destination. There are two basic type of routing. The first type is fully-qualified and uses all bits of the target DPC. The other type is summary routing that uses a subset of the bits in the target DPC and is used to represent groups of point codes rather than a single point code. Example of route table entries. Example 1: variant = ITU DPC/MASK Priority Linkset-name -------- -------- ----------------------- 5.5.5/14 3 STP1-STP2 5.5.5/14 7 STP1-STP3 Description: Two route table entries that define a primary route using linkset 'STP1-STP2' and an alternate route using linkset 'STP1-STP3' to point-code 5.5.5. Example 2: variant = ITU DPC/MASK Priority Linkset-name -------- -------- ----------------------- 5.5.5/14 3 STP1-STP2 5.5.5/14 3 STP1-STP3 5.5.5/14 7 STP1-STP4 Description: Two route table entrys that define a combined linkset consisting of linkset 'STP1-STP2' and 'STP1-STP3' to point code 5.5.5. An alternate route is also defined using linkset 'STP1-STP4'. Example 3: variant = ANSI DPC/MASK Priority Linkset-name -------- -------- ----------------------- 5.5.0/16 3 STP1-STP2 Description: A route table entry that defines routing to a cluster. The cluster represents all point codes in the range from 5.5.0-5.5.255. Example 4: variant = ANSI DPC/MASK Priority Linkset-name -------- -------- ----------------------- 5.5.0/16 3 STP1-STP3 5.5.5/24 3 STP1-STP2 Description: The mixing of fully-qualified and summary route table entrys allow for different routes to be defined for certain DPC in a cluster. In this configuration, the fully-qualified route will be the primary and the summary route will act as a backup. Route table: A group of route table entrys used to route MSU for a particular instance of a signalling point. A sample route table. DPC/MASK Priority Linkset-name -------- -------- ----------------------- 0.0.0/0 7 STP1-STP4 5.5.0/16 3 STP1-STP3 5.5.5/24 3 STP1-STP2 . . 122.5.5 5 STP1-STP2 . . 243.200.1 6 STP1-STP3 " REVISION "200307100000Z" DESCRIPTION "Updated description to provide overview and additional information. The ability to allow multiple instances of Signalling Points to run in the same device has introduce a new index structure. All objects in this MIB will be deprecated and replaced by objects in the CISCO-ITP-GACT-MIB.my MIB." REVISION "200201070000Z" DESCRIPTION "The following objects were added to provide information on time and status of route table loads using the file format. cItpRtConfigLoad cItpRtConfigLoadStatus The following objects were added to provide information on route state changes. cItpRtStateChangeCount cItpRtStateChangeNotifEnabled cItpRtMaxDynamicRoutes cItpRtChangeNotifWindowTime cItpRtChangeNotifMaxPerWindow cItpRtNotifInfoSuppressedFlag cItpRtNotifInfoStateChanges cItpRouteStateChange" REVISION "200108290000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 228 } -- Top-level structure of the MIB cItpRouteNotifications OBJECT IDENTIFIER ::= { ciscoItpRtMIB 0 } cItpRtMIBObjects OBJECT IDENTIFIER ::= { ciscoItpRtMIB 1 } cItpRtMIBConformance OBJECT IDENTIFIER ::= { ciscoItpRtMIB 2 } cItpRtScalars OBJECT IDENTIFIER ::= { cItpRtMIBObjects 1 } cItpRtTables OBJECT IDENTIFIER ::= { cItpRtMIBObjects 2 } cItpRtNotificationsInfo OBJECT IDENTIFIER ::= { cItpRtMIBObjects 3 } -- ************************************************************* -- * * -- * SP - Scalars * -- * * -- ************************************************************* cItpRtConfigLastChanged OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The value of sysUpTime at the time of the last creation or deletion of an entry in the cItpRouteTable. If the local network management subsystem is re-initialization, then this object contains the sysUpTime at the time when this occurred. This value can be used to prevent unnecessary walks of the cItpRouteTable." ::= { cItpRtScalars 1 } cItpRtConfigLoad OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The value of sysUpTime at the time of the last load of the route table using file format." ::= { cItpRtScalars 2 } cItpRtConfigLoadStatus OBJECT-TYPE SYNTAX CItpTcTableLoadStatus MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The status of the current load or status from the prior load operation. This object will have a value of loadInProgress while the load operation is in progress. The cItpRtConfigLoad contains a timestamp indicating when the load operation completed." ::= { cItpRtScalars 3 } cItpRtStateChangeCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A count of the number of routes that have changed states. This value is incremented whenever the destination state of a route changes. This value is used to provide an indicator of the stability of the routing table information." ::= { cItpRtScalars 4 } cItpRtStateChangeNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A control to enable or disable cItpRouteStateChange notifications as follows: 'true' Indicates that the cItpRouteStateChange notification should be generated when the state of any route changes. That is, the notification generation is enabled. 'false' Indicates that cItpRouteStateChange notification generation is disabled." DEFVAL { false } ::= { cItpRtScalars 5 } cItpRtChangeNotifDelayTime OBJECT-TYPE SYNTAX Unsigned32 (0..60) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the maximum amount of time to delay before generating the cItpRouteStateChange notification. The delay is introduced to allow multiple route state changes to be bundled into a single notification. If the value of this object is equal to 0, the device will generate cItpRouteStateChange notification as each route changes states. If the value of this object is greater than 0, the device will not generate notifications as routes change state. As routes changes state they are accumulated until the time specified in cItpRtChangeNotifDelayTime has elapsed or enough state changes have been accumulated to fill up the cItprtNotifInfoStateChanges object. This object is ignored by the agent when the cItpRtStateChangeNotifEnabled object is set to the 'false' value." DEFVAL { 10 } ::= { cItpRtScalars 6 } cItpRtMaxDynamicRoutes OBJECT-TYPE SYNTAX Integer32 (100..1000) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The maximum number of dynamic SS7 routes. This object is used to limit the size of the route table by preventing unbounded growth of dynamic entries. Dynamic entries are created when certain MTP3 management messages are received or sent. The removal of dynamic routes is performed periodically and the older dynamic routes are removed until the specified number is reached." DEFVAL { 500 } ::= { cItpRtScalars 7 } cItpRtChangeNotifWindowTime OBJECT-TYPE SYNTAX Integer32 (30..900) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the time interval used to monitor the rate of route state changes notifications. This object in combination with cItpRtChangeNotifMaxPerWindow are used to determine the notification transit rate and suppress route state notifications." DEFVAL { 60 } ::= { cItpRtScalars 8 } cItpRtChangeNotifMaxPerWindow OBJECT-TYPE SYNTAX Integer32 (10..9000) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the maximum number of route state changes that can occur in the time interval specified in the cItpRtChangeNotifMaxPerWindow object. If additional state changes can occur in the specified time interval the notifications are suppressed." DEFVAL { 60 } ::= { cItpRtScalars 9 } -- ************************************************************* -- * * -- * SP - Route Table * -- * * -- ************************************************************* cItpRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF CItpRouteTableEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The route table for determining the linkset that a packet must traverse to arrive at its destination node given by the destination point code." ::= { cItpRtTables 1 } cItpRouteTableEntry OBJECT-TYPE SYNTAX CItpRouteTableEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each table entry represents a configured route statement." INDEX { cItpRouteTableName, cItpRouteDpc, cItpRouteMask, cItpRouteDestLsCost, cItpRouteDestLinkset } ::= { cItpRouteTable 1 } CItpRouteTableEntry ::= SEQUENCE { cItpRouteTableName CItpTcRouteTableName, cItpRouteDpc CItpTcPointCode, cItpRouteDestLsCost Unsigned32, cItpRouteDestLinkset CItpTcLinksetId, cItpRouteMask Unsigned32, cItpRouteQos CItpTcQos, cItpRouteStatus INTEGER, cItpRouteNonAdjStatus INTEGER } cItpRouteTableName OBJECT-TYPE SYNTAX CItpTcRouteTableName MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The configured name for this route table." ::= { cItpRouteTableEntry 1 } cItpRouteDpc OBJECT-TYPE SYNTAX CItpTcPointCode MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The destination point code." ::= { cItpRouteTableEntry 2 } cItpRouteDestLsCost OBJECT-TYPE SYNTAX Unsigned32 (1..9) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The cost assigned to this linkset matching this route. Higher numbers represent higher cost." ::= { cItpRouteTableEntry 3 } cItpRouteDestLinkset OBJECT-TYPE SYNTAX CItpTcLinksetId MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The linkset that the packet is to be forwarded to on matching this route." ::= { cItpRouteTableEntry 4 } cItpRouteMask OBJECT-TYPE SYNTAX Unsigned32 (0..16777215) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The mask used to define which part of cItpRouteDpc is significant when comparing the cItpRouteDpc to the destination code point in the packet to be routed." ::= { cItpRouteTableEntry 5 } cItpRouteQos OBJECT-TYPE SYNTAX CItpTcQos MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The quality of service classification to be assigned to the ip packets used to transport the SS7 messages. The value to specify for packets when they will be transported on SCTP/IP based linkset." ::= { cItpRouteTableEntry 6 } cItpRouteStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), available(2), restricted(3), unavailable(4) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "List of the possible route status values. 'unknown' : Status can not be determined. 'available' : Route is available. 'restricted' : Traffic is restricted on route. 'unavailable' : Route is unable to service traffic." ::= { cItpRouteTableEntry 7 } cItpRouteNonAdjStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), allowed(2), restricted(3), prohibited(4) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "List of the possible non-adjacent status values. 'unknown' : Status can not be determined. 'allowed' : traffic is allowed. 'restricted' : Traffic is restricted on route. 'prohibited' : Route is prohibited from providing traffic." ::= { cItpRouteTableEntry 8 } -- ************************************************************* -- * * -- * Notifications Information * -- * * -- ************************************************************* cItpRtNotifInfoSuppressedFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A flag to indicate whether cItpRouteStateChange notifications have been suppressed in the current time interval specified by the cItpRtChangeNotifWindowTime object. 'true' Indicates that the device has suppressed the sending of cItpRouteStateChange notifications for the remainder of the time interval. 'false' Indicates that the device has not suppressed the sending of cItpRouteStateChange notifications in the current time interval." ::= { cItpRtNotificationsInfo 1 } cItpRtNotifInfoStateChanges OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..480)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object contains a list of route state changes accumulated until the list is full or the time time interval specified in cItpRtChangeNotifDelayTime has passed. It consists of one or more tuples packed together in the format of '<tuple1><tuple2>...<tuple15>'. Each tuple consist of 32 octets in the following format. '<cItpRouteTableName> 20 octets null padded <cItpRouteDpc> 4 octets <cItpRouteMask> 4 octets destination status 1 octet 1 - unknown state 2 - route is accessible 3 - route is inaccessible 4 - route is restricted' reserved1 1 octet(set to null) reserved2 1 octet(set to null) reserved3 1 octet(set to null) The maximum number of tuples is 15." ::= { cItpRtNotificationsInfo 2 } -- ************************************************************* -- * * -- * Notifications * -- * * -- ************************************************************* cItpRouteStateChange NOTIFICATION-TYPE OBJECTS { cItpRtStateChangeCount, cItpRtNotifInfoSuppressedFlag, cItpRtNotifInfoStateChanges } STATUS deprecated DESCRIPTION "This notification is generated whenever one or more route destination status changes states and includes the count of all route state changes. This notification contains a list of route state changes in the cItpRtNotifInfoStateChanges object. State changes are accumulated until the cItpRtNotifInfoStateChanges is full or the maximum delay time is reached. The delay time is specified by the cItpRtChangeNotifDelayTime object. It may be necessary to suppress the sending of notification when a large number route change state, due the failure of some common resource. The number of notifications can be controlled by specifying values for cItpRtChangeNotifWindowTime and cItpRtChangeNotifMaxPerWindow objects. When the number of route state changes exceed the specified value the last notification will indicate that notifications are suppressed for the remainder of the window." ::= { cItpRouteNotifications 1 } -- ************************************************************* -- * * -- * Conformance Information * -- * * -- ************************************************************* cItpRtMIBCompliances OBJECT IDENTIFIER ::= { cItpRtMIBConformance 1 } cItpRtMIBGroups OBJECT IDENTIFIER ::= { cItpRtMIBConformance 2 } -- Compliance cItpRtMIBCompliance MODULE-COMPLIANCE STATUS deprecated -- superceded by cItpRtMIBComplianceRev1 DESCRIPTION "The compliance statement for entities which implement the Cisco CISCO-ITP-RT-MIB.my MIB" MODULE -- this module MANDATORY-GROUPS { cItpRtScalarGroup, cItpRouteGroup } ::= { cItpRtMIBCompliances 1 } cItpRtMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the Cisco CISCO-ITP-RT-MIB.my MIB" MODULE -- this module MANDATORY-GROUPS { cItpRtScalarGroup, cItpRouteGroup, cItpRtNotificationsGroup, cItpRtScalarGroupRev1 } ::= { cItpRtMIBCompliances 2 } -- Units of Conformance cItpRtScalarGroup OBJECT-GROUP OBJECTS { cItpRtConfigLastChanged } STATUS deprecated DESCRIPTION "Route scalars Group." ::= { cItpRtMIBGroups 1 } cItpRouteGroup OBJECT-GROUP OBJECTS { cItpRouteQos, cItpRouteStatus, cItpRouteNonAdjStatus } STATUS deprecated DESCRIPTION "Route table group." ::= { cItpRtMIBGroups 2 } cItpRtNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { cItpRouteStateChange } STATUS deprecated DESCRIPTION "Route notification objects." ::= { cItpRtMIBGroups 3 } cItpRtScalarGroupRev1 OBJECT-GROUP OBJECTS { cItpRtConfigLoad, cItpRtConfigLoadStatus, cItpRtStateChangeCount, cItpRtStateChangeNotifEnabled, cItpRtChangeNotifDelayTime, cItpRtMaxDynamicRoutes, cItpRtChangeNotifWindowTime, cItpRtChangeNotifMaxPerWindow, cItpRtNotifInfoSuppressedFlag, cItpRtNotifInfoStateChanges } STATUS deprecated DESCRIPTION "Route revision one scalars group." ::= { cItpRtMIBGroups 4 } END