CISCO-RMON-CONFIG-MIB device MIB details by Cisco
CISCO-RMON-CONFIG-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-RMON-CONFIG-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-RMON-CONFIG-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- $Source# -- ***************************************************************** -- CISCO-RMON-CONFIG-MIB.my: Cisco RMON Configuration Extensions -- -- January 1998, Andy Bierman -- February 2001, Edward Pham -- -- Copyright (c) 1998-2001 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** -- CISCO-RMON-CONFIG-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TruthValue FROM SNMPv2-TC ifIndex, InterfaceIndex FROM IF-MIB portCopyEntry FROM SMON-MIB ciscoMgmt FROM CISCO-SMI; ciscoRmonConfigMIB MODULE-IDENTITY LAST-UPDATED "200210080000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-rmon@cisco.com" DESCRIPTION "This module defines configuration extensions for some of the IETF RMON MIBs. The following terms are used throughout this MIB: A span session is an association of one or more destination(s) with a set of source(s), along with other parameters, to specify the network traffic to be monitored. Each span session is denoted by an unique number. The term 'remote span', also called 'RSPAN', refers to the analysis of network traffic remotely, from destination port(s) for one or more source ports, distributed in one or more switches in a switched network, through a RSPAN VLAN." REVISION "200210080000Z" DESCRIPTION "Added rmonMaxAlarms and rmonAlarmEnable." REVISION "200104010000Z" DESCRIPTION "Add the portCopyReflectorPort mib object" REVISION "200102220000Z" DESCRIPTION "Add the following mib objects: portCopyDestLoVlanMask, portCopyDestHiVlanMask, portCopyOption, portCopySessionNo, portCopySessionType, portCopyRemoveSrc, portCopyMaxIngressSessions, portCopyMinEgressSessions." REVISION "9812010000Z" DESCRIPTION "Updated the portCopyXTable; portCopyDirection moved to SMON standard, and multiple VLANs per source port now supported." ::= { ciscoMgmt 103 } ciscoRmonConfigObjects OBJECT IDENTIFIER ::= { ciscoRmonConfigMIB 1 } ciscoRmonConfigNotifications OBJECT IDENTIFIER ::= { ciscoRmonConfigMIB 2 } ciscoRmonConfigConformance OBJECT IDENTIFIER ::= { ciscoRmonConfigMIB 3 } ciscoRmon2ConfigObjects OBJECT IDENTIFIER ::= { ciscoRmonConfigObjects 1 } ciscoSmonConfigObjects OBJECT IDENTIFIER ::= { ciscoRmonConfigObjects 2 } ciscoSampleConfigObjects OBJECT IDENTIFIER ::= { ciscoRmonConfigObjects 3 } ciscoAlarmConfigObjects OBJECT IDENTIFIER ::= { ciscoRmonConfigObjects 4 } -- -- Extensions to the RMON-2 MIB -- rmonTimeFilterMode OBJECT-TYPE SYNTAX INTEGER { stopAfterOne(1), stopAfterAll(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the way the SNMP agent implements the getnext operation for tables with a TimeFilter index, such as those found in the RMON2-MIB module. If this object has the value `stopAfterOne(1)', then a GetNext or GetBulk operation will provide one pass through a given table, i.e., the agent will continue to the next object or table, instead of incrementing a TimeMark INDEX value, even if there exists higher TimeMark values which are valid for the same conceptual row. This mode is not strictly compliant with the TimeFilter textual convention definition, because potentially many conceptual rows will be skipped instead of returned in a GetNext or GetBulk operation. Such rows are identical to each other, except for the returned TimeMark INDEX value. This mode is intended only for testing purposes, however it may also be useful if an NMS wishes to utilize the GetBulk PDU. This mode will prevent the GetBulk responses from containing duplicate rows due to the TimeFilter mechanism. If this object has the value `stopAfterAll(2)', then a getNext or getBulk MIB walk will repeat through the same MIB table until the TimeMark for the most-recently changed entry is reached. Note that as long as traffic occurs on the monitored interface, it is possible a highest value of the TimeFilter INDEX may never be reached. This mode is strictly compliant with the TimeFilter textual convention definition. Note that GetBulk PDU responses in this mode will likely contain multiple copies of the same MIB instances, differing only in the TimeMark INDEX value. As an example, consider row 'fooEntry' which was last updated at 'time 1000'. An NMS may use any TimeMark INDEX value in the range '0' to '1000', and the current (i.e., time of get request) counter values for the 'fooEntry' will be returned by agent. In the 'stopAfterOne' mode, the agent will not increment the fooEntry TimeMark index under any conditions. In the 'stopAfterAll' mode, the agent will increment any fooEntry TimeMark INDEX value in the range '0' to '999', up until the TimeMark value of '1000' is reached." DEFVAL { stopAfterAll } ::= { ciscoRmon2ConfigObjects 1 } -- -- Extensions to the SMON MIB -- portCopyXTable OBJECT-TYPE SYNTAX SEQUENCE OF PortCopyXEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends the port copy capability found in the SMON MIB portCopyTable. This table is intended to augment every portCopyEntry, but not all features provided may be available on all RMON platforms. In such a case, a particular MIB object will be implemented with read-only access." ::= { ciscoSmonConfigObjects 1 } portCopyXEntry OBJECT-TYPE SYNTAX PortCopyXEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a particular port copy extension entry. When creating an entry in this table using the 'createAndwait' method, the following rules are applied: - no span consistency check is done for the entry until the entry is activated. An entry will not be activated if it fails the span consistency check described for the 'createAndGo' method. -an instance remains in the 'notReady' state until the associated portCopyStatus changes to 'active'. When the agent processes a request of adding an entry using 'createAndGo' method or a request that sets the value of portCopyStatus object to 'active', the following rules are applied: The agent will add the entry to a span session having the same portCopySessionNo, or create a new session if it does not exist. To join an existing session, either portCopySource or portCopyDest, but not both, must exist in one of the entries from the same span session. In addition, the following actions will be taken after a successful join: 1. The portCopyDirection, portCopyLoVlanMask, and portCopyHiVlanMask values will overwrite the existing values associated with this port copy session. 2. The portCopyDestLoVlanMask, portCopyDestHiVlanMask, and portCopyOption values will overwrite the existing values associated the same portCopyDest and this port copy session. 3. If the value of portCopyDest object does not exist in the existing span session, each of the ports identified in the portCopySource is added to this span session. For example, given an existing span session having ports 1, 2, and 3 as source ports, and port A as the destination port, if an entry is added by an NMS with indices of (2,B), the agent will also add entries for the other source ports (e.g. (1,B) and (3,B)) to the session. The same algorithm for adding entries will be applied if the portCopySource does not already belong to this span session. When the agent processes a request to change the RowStatus of an entry from 'active' to 'notInService', the following rules are applied: - That entry will be removed from its participating span session. The new RowStatus state will be 'notInService'. - all entries in the table that have the same value of portCopySessionNo and same value of portCopySource are also set to 'NotInService'. When agent processes a request to delete an entry, the following rules are applied: - the entry is simply removed if it is not currently active. - if the portCopySessionNo value is non-zero and the value of portCopyRemoveSrc object is set to 'true', then all entries with the same value of portCopySessionNo and same value of portCopySource are deleted. - if the portCopySessionNo value is non-zero and the value of portCopyRemoveSrc object is set to 'false', then all entries with the same value of portCopySessionNo and same value of portCopyDest are deleted. - if the last portCopy entry is removed from a session, then the session information is also removed." AUGMENTS { portCopyEntry } ::= { portCopyXTable 1 } PortCopyXEntry ::= SEQUENCE { portCopyLoVlanMask OCTET STRING, portCopyHiVlanMask OCTET STRING, portCopyDestLoVlanMask OCTET STRING, portCopyDestHiVlanMask OCTET STRING, portCopyOption BITS, portCopySessionNo Integer32, portCopySessionType INTEGER, portCopyRemoveSrc TruthValue, portCopyReflectorPort InterfaceIndex } portCopyLoVlanMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the portCopyHiVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to select or deselect VLAN IDs 0 though 2047. If this object contains a zero-length string, or none of the octets contain a non-zero value, and the associated portCopyHiVlanMask is not instantiated, contains a zero-length string, or contains only zero-valued octets, then network traffic will not be filtered, based on IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. If this object has a non-zero length, and at least one octet contains a non-zero value, or the portCopyHiVlanMask contains at least one non-zero octet, then traffic will be filtered, based on the indicated IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. Only frames (tagged or untagged) which match the indicated VLAN ID(s) will be copied to the indicated destination port. VLAN IDs are encoded as a string of octets containing one bit per VLAN to be included in the port copy operation. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the traffic associated with that VLAN will be selected for the indicated port copy operation. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. The creation and deletion of instances of this object is controlled by the portCopyStatus object found in the augmented portCopyEntry. It is an implementation-specific matter as to how many VLANs may be selected from a particular physical source port at any one time, or whether this object may be modified while the associated portCopyStatus object is equal to 'active'." DEFVAL { ''H } ::= { portCopyXEntry 1 } portCopyHiVlanMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the portCopyLoVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to select or deselect VLAN IDs 2048 though 4095. If this object contains a zero-length string, or none of the octets contain a non-zero value, and the associated portCopyLoVlanMask is not instantiated, contains a zero-length string, or contains only zero-valued octets, then network traffic will not be filtered, based on IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. If this object has a non-zero length, and at least one octet contains a non-zero value, or the portCopyLoVlanMask contains at least one non-zero octet, then traffic will be filtered, based on the indicated IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. Only frames (tagged or untagged) which match the indicated VLAN ID(s) will be copied to the indicated destination port. VLAN IDs are encoded as a string of octets containing one bit per VLAN to be included in the port copy operation. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the traffic associated with that VLAN will be selected for the indicated port copy operation. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. The creation and deletion of instances of this object is controlled by the portCopyStatus object found in the augmented portCopyEntry. It is an implementation-specific matter as to how many VLANs may be selected from a particular physical source port at any one time, or whether this object may be modified while the associated portCopyStatus object is equal to 'active'." DEFVAL { ''H } ::= { portCopyXEntry 2 } portCopyDestLoVlanMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object affects the way VLAN-based traffic to a switch destination port is filtered for the indicated port copy operation. It is used in tandem with the portCopyDestHiVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to select or deselect VLAN IDs 0 though 2047. If this object contains a zero-length string, or none of the octets contain a non-zero value, and the associated portCopyDestHiVlanMask is not instantiated, contains a zero-length string, or contains only zero-valued octets, then network traffic will not be filtered, based on IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. If this object has a non-zero length, and at least one octet contains a non-zero value, or the portCopyDestHiVlanMask contains at least one non-zero octet, then traffic will be filtered, based on the indicated IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. Only frames (tagged or untagged) which match the indicated VLAN ID(s) will be copied to the indicated destination port. If a VLAN is included in the portCopyDestLoVlanMask object, it should also be included in the portCopyLoVlanMask object and vice versa. VLAN IDs are encoded as a string of octets containing one bit per VLAN to be included in the port copy operation. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the traffic associated with that VLAN will be selected for the indicated port copy operation. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. The creation and deletion of instances of this object is controlled by the portCopyStatus object found in the augmented portCopyEntry. It is an implementation-specific matter as to how many VLANs may be selected from a particular physical source port at any one time, or whether this object may be modified while the associated portCopyStatus object is equal to 'active'." DEFVAL { ''H } ::= { portCopyXEntry 3 } portCopyDestHiVlanMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object affects the way VLAN-based traffic to a switch destination port is filtered for the indicated port copy operation. It is used in tandem with the portCopyDestLoVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to select or deselect VLAN IDs 2048 though 4095. If this object contains a zero-length string, or none of the octets contain a non-zero value, and the associated portCopyDestLoVlanMask is not instantiated, contains a zero-length string, or contains only zero-valued octets, then network traffic will not be filtered, based on IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. If this object has a non-zero length, and at least one octet contains a non-zero value, or the portCopyDestLoVlanMask contains at least one non-zero octet, then traffic will be filtered, based on the indicated IEEE 802.1Q or ISL VLAN ID, before it is copied to the indicated destination port. Only frames (tagged or untagged) which match the indicated VLAN ID(s) will be copied to the indicated destination port. If a VLAN is included in the portCopyDestHiVlanMask object, it should also be included in the portCopyHiVlanMask object and vice versa. VLAN IDs are encoded as a string of octets containing one bit per VLAN to be included in the port copy operation. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the traffic associated with that VLAN will be selected for the indicated port copy operation. Note that if the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. The creation and deletion of instances of this object is controlled by the portCopyStatus object found in the augmented portCopyEntry. It is an implementation-specific matter as to how many VLANs may be selected from a particular physical source port at any one time, or whether this object may be modified while the associated portCopyStatus object is equal to 'active'." DEFVAL { ''H } ::= { portCopyXEntry 4 } portCopyOption OBJECT-TYPE SYNTAX BITS { inpkts(0), learningDisable(1), dot1q(2), isl(3), multicast(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the additional span configuration on destination port. Instances of same portCopyDest index must have same values in portCopyOption. Changes on portCopyOption of one instance will be applied to all other instances of same portCopyDest index. - inpkts(0) This bit is set to enable the destination port to receive normal incoming traffic. - learningDisable(1) This bit is set to suppress MAC learning for incoming traffic at the destination port. - dot1q(2) This bit is set for dot1q trunking encapsulation of forwarded traffic at the destination port. This bit can not be set when isl(3) bit is 1. - isl(3) This bit is set for isl trunking encapsulation of forwarded traffic at the destination port. This bit can not be set when dot1q(2) bit is 1. - multicast(4) This bit is set to enable the destination port to receive multicast traffic." DEFVAL { { } } ::= { portCopyXEntry 5 } portCopySessionNo OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the arbitrary unique identifier for this span session. If a non zero value is specified, the agent will check if a span session that has the same session number exists. If so, the agent will use this session number when this entry is activated. This entry will be added to the existing span session (identified by all entries with the same portCopySessionNo value). If no such session exists, a new span session is created and assigned the specified value. Otherwise, the agent will check if the destination port belongs to an existing span session. If so, the agent will assign that session number when this entry is activated. This entry will be added to the existing span session (identified by all entries with the same portCopySessionNo value). If no such session exists, a new span session is created and assigned an arbitrary, locally unique value. If the associated portCopyStatus object is equal to 'active', then this object may not be modified." DEFVAL {0} ::= { portCopyXEntry 6 } portCopySessionType OBJECT-TYPE SYNTAX INTEGER { notSpecified(1), -- session type not specified local(2), -- local session remoteSource(3), -- remote source session remoteDestination(4) -- remote destination session } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the span session type. 'remoteSource' refers to session where traffic is copied from source port to RSPAN VLAN as its destination port. 'remoteDestination' refers to session where traffic is copied from RSPAN VLAN to the destination port. For local span session, both source and destination ports reside in the same switch. In a set operation, agent will decide the actual span type for the session if this mib object is 'notSpecified' based on type of source and destination ports. A read operation will return one of the other three types. Changes on portCopySessionType of one entry will be applied to all existing active entries having the same value of portCopySessionNo. If the associated portCopyStatus object is equal to 'active', then this object may not be modified." DEFVAL { notSpecified } ::= { portCopyXEntry 7 } portCopyRemoveSrc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how the agent will modify a span session when an entry belonging to this session is deleted. The value 'true' specifies source port based entry deletion. In source port based delection, all entries of same index portCopySource from the session are to be deleted. The value 'false' specifies destination based entry deletion. In destination port based deletion, all entries of same index portCopyDest from the session are to be deleted." DEFVAL { true } ::= { portCopyXEntry 8 } portCopyReflectorPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the reflector port of this span session. The value of this object is ignored whenever the value of portCopySessionType is not remoteSource(3)." ::= { portCopyXEntry 9 } portCopyMaxIngressSessions OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of local ingress (rx or both) span session that can be configured on this agent." ::= { ciscoSmonConfigObjects 2 } portCopyMaxEgressSessions OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of local egress span sessions that can be configured on this agent." ::= { ciscoSmonConfigObjects 3 } -- -- Extensions to configure Statistical Sampling based collection -- of the RMON-1, RMON-2, HC-RMON, and SMON MIBs. -- rmonSampleConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonSampleConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table controls the configuration of RMON collection based on statistical sampling techniques, for each monitored interface on the RMON probe. It is a SPARSE-AUGMENTS of the ifEntry found in the IF-MIB module. An entry is created in this table at the same time the augmented ifEntry is created (usually at system startup time), for each interface which can be monitored by the RMON agent. An associated entry in the SMON MIB dataSourceCapsTable is also created for each RMON-capable interface at the same time. An RMON collection is associated with a particular interface if the control table dataSource OBJECT IDENTIFIER is of the form 'ifIndex.I', and 'I' is the same value as the ifIndex value for the ifEntry and rmonSampleConfigEntry." ::= { ciscoSampleConfigObjects 1 } rmonSampleConfigEntry OBJECT-TYPE SYNTAX RmonSampleConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a particular sampling configuration for the indicated RMON-capable interface." INDEX { ifIndex } ::= { rmonSampleConfigTable 1 } RmonSampleConfigEntry ::= SEQUENCE { rmonSamplingEnabled TruthValue } rmonSamplingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object affects the way the RMON probe uses statistical sampling to collect packets from the indicated interface. If this object has the value 'false', then the probe will attempt to monitor all packets detected on the indicated interface, in the event any RMON collections are actually configured. The data returned in all RMON collection tables associated with this interface will represent non-sampled monitored counter values. If this object has the value 'true', then the probe will use adaptive statistical sampling techniques to monitor the indicated interface, in the event any RMON collections are actually configured. The data returned in RMON collection tables associated with this interface may be based on statistical approximations. In this mode, the RMON agent will also maintain additional MIB objects to provide the confidence interval information for each sampled counter. These objects can be found in the CISCO-RMON-SAMPLING-MIB. When this object transitions from 'false' to 'true', all active packet capture functions will be suspended, without affecting the contents of any associated filterEntry, filter2Entry, channelEntry, channel2Entry, bufferControlEntry, captureBufferEntry, or captureBufferHighCapacityEntry. Only the low-level packet capture processing is deactivated. When this object transitions from 'true' to 'false', all suspended packet capture functions associated with the interface will be reactivated. Note that an NMS application which is unaware of this MIB object will not be able to detect suspended packet capture operations or sampled collections, however multi-manager mis-configuration issues are beyond the scope of this MIB. The packet capture function Get and Set operations are not affected by this object. If an interface cannot be sampled, or the sampling configuration cannot be modified, then such an instance of this object will be implemented with read-only access." DEFVAL { false } ::= { rmonSampleConfigEntry 1 } -- -- RMON Alarm config group -- Objects to controls alarms of alarmTable RMON-MIB -- rmonMaxAlarms OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of entries allowed in the alarmTable." DEFVAL { 100 } ::= {ciscoAlarmConfigObjects 1 } rmonAlarmEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines if the RMON alarm feature is enabled/disabled on this device. If this object is set to 'true', the RMON alarm feature enabled. If this object is 'false', RMON alarm feature is disabled. If the RMON feature is disabled, all the RMON alarm related polling are stopped. Note that this object is only intended for temporary disabling of RMON alarm feature to ensure that the CPU usage by RMON alarms is not detrimental. For permanent disabling on this feature, it suggested that all the entries in the alarmTable are removed." DEFVAL { true } ::= {ciscoAlarmConfigObjects 2 } -- -- Notifications Section -- (none defined) -- -- -- Conformance Section -- ciscoRmonConfigCompliances OBJECT IDENTIFIER ::= { ciscoRmonConfigConformance 1 } ciscoRmonConfigGroups OBJECT IDENTIFIER ::= { ciscoRmonConfigConformance 2 } ciscoRmonConfigCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Describes the requirements for conformance to Cisco RMON Configuration Extensions MIB." -- no mandatory groups MODULE -- this module GROUP rmon2ExtensionsGroup DESCRIPTION "The rmon2ExtensionsGroup is mandatory for systems which implement the RMON-2 MIB [RFC2021]." GROUP smonExtensionsGroup DESCRIPTION "The smonExtensionsGroup is mandatory for systems which implement the SMON-MIB [RFC 2613]." OBJECT portCopyHiVlanMask MIN-ACCESS not-accessible DESCRIPTION "This object is not mandatory for implementations which do not support VLAN IDs greater than 2047." GROUP rmonSampleConfigGroup DESCRIPTION "The rmonSampleConfigGroup is mandatory for systems which implement RMON instrumentation based on statistical sampling techniques." OBJECT rmonSamplingEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoRmonConfigCompliances 1 } ciscoRmonConfigComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Describes the requirements for conformance to Cisco RMON Configuration Extensions MIB." -- no mandatory groups MODULE -- this module GROUP rmon2ExtensionsGroup DESCRIPTION "The rmon2ExtensionsGroup is mandatory for systems which implement the RMON-2 MIB [RFC2021]." GROUP smonExtensionsGroup DESCRIPTION "The smonExtensionsGroup is mandatory for systems which implement the SMON-MIB [RFC 2613]." OBJECT portCopyHiVlanMask MIN-ACCESS not-accessible DESCRIPTION "This object is not mandatory for implementations which do not support VLAN IDs greater than 2047." GROUP smonExtensions2Group DESCRIPTION "The smonExtensions2Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support vlan filtering at SPAN destination port." GROUP smonExtensions3Group DESCRIPTION "The smonExtensions3Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support additional configuration at SPAN destination port." GROUP smonExtensions4Group DESCRIPTION "The smonExtensions4Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support SPAN session concept." GROUP smonExtensions5Group DESCRIPTION "The smonExtensions5Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support local and remote SPAN." GROUP smonExtensions6Group DESCRIPTION "The smonExtensions6Group is mandatory for systems which implement the SMON-MIB [RFC 2613]." GROUP smonExtensions7Group DESCRIPTION "The smonExtensions7Group is mandatory for systems which implement the SMON-MIB [RFC 2613] and require reflector port." OBJECT portCopyDestHiVlanMask MIN-ACCESS not-accessible DESCRIPTION "This object is not mandatory for implementations which do not support VLAN IDs greater than 2047." GROUP rmonSampleConfigGroup DESCRIPTION "The rmonSampleConfigGroup is mandatory for systems which implement RMON instrumentation based on statistical sampling techniques." OBJECT rmonSamplingEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { ciscoRmonConfigCompliances 2 } ciscoRmonConfigComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to Cisco RMON Configuration Extensions MIB." -- no mandatory groups MODULE -- this module GROUP rmon2ExtensionsGroup DESCRIPTION "The rmon2ExtensionsGroup is mandatory for systems which implement the RMON-2 MIB [RFC2021]." GROUP smonExtensionsGroup DESCRIPTION "The smonExtensionsGroup is mandatory for systems which implement the SMON-MIB [RFC 2613]." OBJECT portCopyHiVlanMask MIN-ACCESS not-accessible DESCRIPTION "This object is not mandatory for implementations which do not support VLAN IDs greater than 2047." GROUP smonExtensions2Group DESCRIPTION "The smonExtensions2Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support vlan filtering at SPAN destination port." GROUP smonExtensions3Group DESCRIPTION "The smonExtensions3Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support additional configuration at SPAN destination port." GROUP smonExtensions4Group DESCRIPTION "The smonExtensions4Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support SPAN session concept." GROUP smonExtensions5Group DESCRIPTION "The smonExtensions5Group is mandatory only for systems which implement the SMON-MIB [RFC 2613] and support local and remote SPAN." GROUP smonExtensions6Group DESCRIPTION "The smonExtensions6Group is mandatory for systems which implement the SMON-MIB [RFC 2613]." GROUP smonExtensions7Group DESCRIPTION "The smonExtensions7Group is mandatory for systems which implement the SMON-MIB [RFC 2613] and require reflector port." OBJECT portCopyDestHiVlanMask MIN-ACCESS not-accessible DESCRIPTION "This object is not mandatory for implementations which do not support VLAN IDs greater than 2047." GROUP rmonSampleConfigGroup DESCRIPTION "The rmonSampleConfigGroup is mandatory for systems which implement RMON instrumentation based on statistical sampling techniques." OBJECT rmonSamplingEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP rmonAlarmConfigGroup DESCRIPTION "The rmonAlarmConfigGroup is not mandatory for systems which do not support RMON alarm controls as an extension to RMON-MIB." ::= { ciscoRmonConfigCompliances 3 } rmon2ExtensionsGroup OBJECT-GROUP OBJECTS { rmonTimeFilterMode } STATUS current DESCRIPTION "A collection of objects providing configuration extensions for the RMON2-MIB module." ::= { ciscoRmonConfigGroups 1 } smonExtensionsGroup OBJECT-GROUP OBJECTS { portCopyLoVlanMask, portCopyHiVlanMask } STATUS current DESCRIPTION "A collection of objects providing configuration extensions for the SMON-MIB module." ::= { ciscoRmonConfigGroups 2 } rmonSampleConfigGroup OBJECT-GROUP OBJECTS { rmonSamplingEnabled } STATUS current DESCRIPTION "A collection of objects providing configuration extensions for RMON agent implementations which support statistical sampling techniques." ::= { ciscoRmonConfigGroups 3 } smonExtensions2Group OBJECT-GROUP OBJECTS { portCopyDestLoVlanMask, portCopyDestHiVlanMask } STATUS current DESCRIPTION "A collection of objects providing additional port copy configuration for destination vlan filtering for the SMON-MIB module." ::= { ciscoRmonConfigGroups 4 } smonExtensions3Group OBJECT-GROUP OBJECTS { portCopyOption } STATUS current DESCRIPTION "A collection of objects providing additional port copy configuration extensions at destination port for the SMON-MIB module." ::= { ciscoRmonConfigGroups 5 } smonExtensions4Group OBJECT-GROUP OBJECTS { portCopySessionNo, portCopyRemoveSrc } STATUS current DESCRIPTION "A collection of objects providing additional port copy configuration extensions for agent that supports SPAN session concept." ::= { ciscoRmonConfigGroups 6 } smonExtensions5Group OBJECT-GROUP OBJECTS { portCopySessionType } STATUS current DESCRIPTION "A collection of objects providing additional port copy configuration extensions for agent that supports local and remote SPAN." ::= { ciscoRmonConfigGroups 7 } smonExtensions6Group OBJECT-GROUP OBJECTS { portCopyMaxIngressSessions, portCopyMaxEgressSessions } STATUS current DESCRIPTION "A collection of objects providing additional port copy information for the SMON-MIB module." ::= { ciscoRmonConfigGroups 8 } smonExtensions7Group OBJECT-GROUP OBJECTS { portCopySessionType, portCopyReflectorPort } STATUS current DESCRIPTION "A collection of objects providing additional port copy configuration extensions for agent that supports reflector port for span session." ::= { ciscoRmonConfigGroups 9 } rmonAlarmConfigGroup OBJECT-GROUP OBJECTS { rmonMaxAlarms, rmonAlarmEnable } STATUS current DESCRIPTION "A collection of objects providing additional RMON configurations to control number alarms and to enable/disable alarms in the alarmTable in RMON-MIB." ::= { ciscoRmonConfigGroups 10 } END