CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB device MIB details by Cisco
CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB.
| Vendor: | Cisco |
|---|---|
| Mib: | CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
-- -- Caution. This MIB is temporary and experimental. -- In the future it will be removed from products, perhaps -- with short notice, in favor of more standard or generic MIBs. -- Application developers should not depend on long-term access -- to this MIB. CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB --REVISION 0.01 DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, DisplayString FROM SNMPv2-TC ciscoExperiment FROM CISCO-SMI rptrGroupIndex, rptrPortGroupIndex, rptrPortIndex FROM SNMP-REPEATER-MIB PhysAddress FROM RFC1213-MIB; ciscoSibuStackableDualSpeedHubMIB MODULE-IDENTITY LAST-UPDATED "9810230000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-sibu@cisco.com" DESCRIPTION "The MIB module that extends the REPEATER-MIB to manage CISCO low end stackable repeater products. For the purpose of this mib, a hub is a repeater group and stack is collection of one or more hubs interconnected via stack bus connectors." REVISION "9810230000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoExperiment 44 } ciscoSibuStackableDualSpeedHubMIBObjects OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIB 1 } cssSystem OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBObjects 1 } cssGroup OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBObjects 2 } cssRepeaterPort OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBObjects 3 } cssSwitchPort OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBObjects 4 } HubNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the hub number that the system supports for stacking. The hub number represents the order in which a hub is stacked relative to other members of the stack. Lowest hub number represents the top member of the stack. This is also the number used in the command line interface." SYNTAX Integer32 (1..2147483647) -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | -- The Dual Speed Hub System Group | -- | -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ cssSystemLinkTraps OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- enable linkUp/linkDown traps disabled(2) -- disable linkUp/linkDown traps } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether the stack is permitted to generate linkUp/linkDown traps for both repeater port and switch module's port. The stack provides only a single global control of link traps in contrast to per interface control provided by IF-MIB. The value of all instances ifLinkUpDownTrapEnable is set to TRUE (FALSE) if this object is set to enabled (disabled). The object ifLinkUpDownTrapEnable is read-only. A linkUp/linkDown trap is generated whenever a port's link STATUS or administrative status changes." DEFVAL { enabled } ::= { cssSystem 1 } -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | -- The Dual Speed Hub Stack Group | -- | -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ cssGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF CssGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of member hubs in the stack." ::= { cssGroup 1 } cssGroupEntry OBJECT-TYPE SYNTAX CssGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration parameters for an individual hub. An entry is created by default for the master unit in the stack. A entry is created (removed) when a hub is connected to (removed from) the stack." INDEX { rptrGroupIndex } ::= { cssGroupTable 1 } CssGroupEntry ::= SEQUENCE { cssGroupID HubNumber, cssGroupType INTEGER, cssGroupSerialNo DisplayString, cssGroupBoardRevision Integer32, cssGroupAgentBootVersion DisplayString, cssGroupAgentFirmwareVersion DisplayString, cssGroupAgentStatus INTEGER, cssGroupAgentPhysAddress PhysAddress, cssGroupInternalPowerState INTEGER, cssGroupRedundantPowerState INTEGER, cssGroupReset INTEGER, cssGroupConfigDefaultReset INTEGER, cssGroupIsolatedState INTEGER } cssGroupID OBJECT-TYPE SYNTAX HubNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The hub identifier of unit in a stack." ::= { cssGroupEntry 1 } cssGroupType OBJECT-TYPE SYNTAX INTEGER { cisco1538MDS(1), -- Cisco 1538M Micro Hub 10/100 cisco1538UDS(2), -- Cisco 1538 Micro Hub 10/100 wsC412M(3), -- FastHub 412M 10/100 wsC412(4), -- FastHub 412 10/100 wsC424M(5), -- FastHub 424M 10/100 wsC424(6) -- FastHub 424 10/100 } MAX-ACCESS read-only STATUS current DESCRIPTION "The model type of the hub unit" ::= { cssGroupEntry 2 } cssGroupSerialNo OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the hardware." ::= { cssGroupEntry 4 } cssGroupBoardRevision OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Hardware version of the repeater board." ::= { cssGroupEntry 5 } cssGroupAgentBootVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the version number of the dual-speed hub BOOT software residing in flash. The format is 'V1.2.3'." ::= { cssGroupEntry 6 } cssGroupAgentFirmwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the version number of the dual-speed hub firmware residing in flash. The format is 'V1.2.3'." ::= { cssGroupEntry 7 } cssGroupAgentStatus OBJECT-TYPE SYNTAX INTEGER { notPresent(1), primary(2), backup(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of this hub agent. Each stack allows only one SNMP primary agent. notPresent(1): The hub does not have an agent. primary(2): The agent of this hub is a primary agent. backup(3) : The agent of this hub is a backup agent." ::= { cssGroupEntry 8 } cssGroupAgentPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of this hub's agent" ::= { cssGroupEntry 9 } cssGroupInternalPowerState OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of the internal power supply. off : The internal power supply is off. on : The internal power supply is on." ::= { cssGroupEntry 12 } cssGroupRedundantPowerState OBJECT-TYPE SYNTAX INTEGER { off(1), healthy(2), faulty(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of the external/backup power supply. off : the switch is not connected to a redundant power source. healthy : a redundant power source is connected to the switch and the power source is operating correctly. faulty : a redundant power source is connected to the switch but a failure exists in the power system." ::= { cssGroupEntry 13 } cssGroupReset OBJECT-TYPE SYNTAX INTEGER { noReset(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read." DEFVAL { noReset } ::= { cssGroupEntry 14 } cssGroupConfigDefaultReset OBJECT-TYPE SYNTAX INTEGER { noReset(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parameters will revert to their factory default settings. Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read." DEFVAL { noReset } ::= { cssGroupEntry 15 } cssGroupIsolatedState OBJECT-TYPE SYNTAX INTEGER { isolated(1), attached(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to isolated(1) causes this hub to be isolated from the back plane bus. Setting this object to attached(2) causes this hub to be attached to the back plane bus." ::= { cssGroupEntry 16 } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | -- The Stackable Dual Speed Hub Port Configuration Table | -- | -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ cssRepeaterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CssRepeaterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of repeater port configurations on each hub unit." ::= { cssRepeaterPort 1 } cssRepeaterPortEntry OBJECT-TYPE SYNTAX CssRepeaterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration parameters for an individual repeater port on a hub. The value of rptrPortIndex also indicates the physical port number of the port in the hub. An entry is created for each repeater port in a hub when the hub is connected to the stack. The corresponding entries are removed when the hub is removed from the stack." INDEX { rptrPortGroupIndex, rptrPortIndex} ::= { cssRepeaterPortTable 1 } CssRepeaterPortEntry ::= SEQUENCE { cssRepeaterPortName DisplayString, cssRepeaterPortControllerRevision Integer32, cssRepeaterPortSpeedAdmin INTEGER, cssRepeaterPortSpeedStatus INTEGER, cssRepeaterPortLinkStatus INTEGER } cssRepeaterPortName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "A descriptive string of up to 20 characters used by the network administrator to name a port." ::= { cssRepeaterPortEntry 1 } cssRepeaterPortControllerRevision OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the revision number of the port controller." ::= { cssRepeaterPortEntry 2 } cssRepeaterPortSpeedAdmin OBJECT-TYPE SYNTAX INTEGER { tenMbps(1), oneHundredMbps(2), autoNegotiate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. The actual operating speed of the port is given by cssRepeaterPortSpeedStatus." DEFVAL { autoNegotiate } ::= { cssRepeaterPortEntry 3 } cssRepeaterPortSpeedStatus OBJECT-TYPE SYNTAX INTEGER { tenMbps(1), -- 10 Mbit/s oneHundredMbps(2) -- 100 Mbit/s } MAX-ACCESS read-write STATUS current DESCRIPTION "The operating speed of the port." ::= { cssRepeaterPortEntry 4 } cssRepeaterPortLinkStatus OBJECT-TYPE SYNTAX INTEGER { link(1), noLink(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current port link status." ::= { cssRepeaterPortEntry 5 } -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | -- The Extension Module Switched Port Group | -- | -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ cssSwitchPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CssSwitchPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of switched ports on extension module on a each hub unit in the stack." ::= { cssSwitchPort 1 } cssSwitchPortEntry OBJECT-TYPE SYNTAX CssSwitchPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration parameters for an individual switch module port. An entry is created for each switch port on a module is inserted into a hub in the stack. The corresponding entries are removed when the module is removed from the hub in the stack, or if the hub is removed from the stack." INDEX { rptrGroupIndex, cssSwitchPortModuleID, cssSwitchPortPortID } ::= { cssSwitchPortTable 1 } CssSwitchPortEntry ::= SEQUENCE { cssSwitchPortModuleID Integer32, cssSwitchPortPortID Integer32, cssSwitchPortName DisplayString, cssSwitchPortType INTEGER, cssSwitchPortControllerRevision Integer32, cssSwitchPortState INTEGER, cssSwitchPortDuplexAdmin INTEGER, cssSwitchPortDuplexStatus INTEGER, cssSwitchPortSpeedAdmin INTEGER, cssSwitchPortSpeedStatus INTEGER, cssSwitchPortLinkStatus INTEGER } cssSwitchPortModuleID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Unique ID number of a module unit in a hub as used in the command line interface." ::= { cssSwitchPortEntry 1 } cssSwitchPortPortID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique ID identifying a port on an extension module on a hub as used in the command line interface." ::= { cssSwitchPortEntry 2 } cssSwitchPortName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "A descriptive string of up to 20 characters used by the network administrator to name a switch port." ::= { cssSwitchPortEntry 3 } cssSwitchPortType OBJECT-TYPE SYNTAX INTEGER { wsX4001(1), -- 10/100 Tx switch module for FastHub 400 wsX4002(2) -- 100BaseFx switch module for FastHub 400 } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of switch module in this hub." ::= { cssSwitchPortEntry 4 } cssSwitchPortControllerRevision OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The revision number of the port controller." ::= { cssSwitchPortEntry 5 } cssSwitchPortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- switch port enabled disabled(2) -- switch port disabled } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to enabled(1) enables the port. Setting this object to disabled(2) disables the port." DEFVAL { enabled } ::= { cssSwitchPortEntry 6 } cssSwitchPortDuplexAdmin OBJECT-TYPE SYNTAX INTEGER { fullDuplex(1), halfDuplex(2), autoNegotiate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to operate in normal mode. Set to autoNegotiate(3) to allow the switch to negotiate the duplex status with the other end of the connection." DEFVAL { autoNegotiate } ::= { cssSwitchPortEntry 7 } cssSwitchPortDuplexStatus OBJECT-TYPE SYNTAX INTEGER { fullDuplex(1), halfDuplex(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operating duplex mode of the switched port." ::= { cssSwitchPortEntry 8 } cssSwitchPortSpeedAdmin OBJECT-TYPE SYNTAX INTEGER { tenMbps(1), oneHundredMbps(2), autoNegotiate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate the operating speed with the other end of the connection. If the value of object cssSwitchPortType is WS-X4002(2), this object will be read-only, because FX module only supports 100Mbps speed." DEFVAL { autoNegotiate } ::= { cssSwitchPortEntry 9 } cssSwitchPortSpeedStatus OBJECT-TYPE SYNTAX INTEGER { tenMbps(1), oneHundredMbps(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operating speed of the switched port." ::= { cssSwitchPortEntry 10 } cssSwitchPortLinkStatus OBJECT-TYPE SYNTAX INTEGER { link(1), noLink(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the link STATUS of switch port." ::= { cssSwitchPortEntry 11 } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | | -- The stackable Dual Speed Hub Switch Enterprise Specific Traps | -- | -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- Notifications ciscoSibuStackableDualSpeedHubNotifications OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIB 2 } ciscoSibuStackableDualSpeedHubNotificationsPrefix OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubNotifications 0 } ciscoSibuStackableDualSpeedHubRptrPortLinkChange NOTIFICATION-TYPE OBJECTS { cssRepeaterPortLinkStatus } STATUS current DESCRIPTION "This trap is generated whenever the value of cssRepeaterPortLinkStatus changes for a repeater port." ::= { ciscoSibuStackableDualSpeedHubNotificationsPrefix 1 } ciscoSibuStackableDualSpeedHubSwitchPortLinkChange NOTIFICATION-TYPE OBJECTS { cssSwitchPortLinkStatus } STATUS current DESCRIPTION "This trap is generated whenever the value of cssSwitchPortLinkStatus changes for a switch port on an extension module." ::= { ciscoSibuStackableDualSpeedHubNotificationsPrefix 2 } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- | -- The Stackable Dual-Speed Ethernet Hub Enterprise Module comformance | -- | -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ciscoSibuStackableDualSpeedHubMIBComformance OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIB 3 } ciscoSibuStackableDualSpeedHubMIBCompliances OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBComformance 1 } ciscoSibuStackableDualSpeedHubMIBGroups OBJECT IDENTIFIER ::= { ciscoSibuStackableDualSpeedHubMIBComformance 2 } -- compliance statements ciscoSibuStackableDualSpeedHubCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the Cisco Stackable Dual-Speed Hub products." MODULE -- this module MANDATORY-GROUPS { ciscoSibuStackableDualSpeedHubGroup, ciscoSibuStackableDualSpeedHubRepeaterPortGroup } GROUP ciscoSibuStackableDualSpeedHubSwitchPortGroup DESCRIPTION "Devices that have switched ports modules must implement objects in this group." ::= { ciscoSibuStackableDualSpeedHubMIBCompliances 1 } -- group statements ciscoSibuStackableDualSpeedHubGroup OBJECT-GROUP OBJECTS { cssSystemLinkTraps, cssGroupID, cssGroupType, cssGroupSerialNo, cssGroupBoardRevision, cssGroupAgentBootVersion, cssGroupAgentFirmwareVersion, cssGroupAgentStatus, cssGroupAgentPhysAddress, cssGroupInternalPowerState, cssGroupRedundantPowerState, cssGroupReset, cssGroupConfigDefaultReset, cssGroupIsolatedState } STATUS current DESCRIPTION "A collection of group objects for use with the Cisco Stackable Dual-Speed Hub products." ::= { ciscoSibuStackableDualSpeedHubMIBGroups 1 } ciscoSibuStackableDualSpeedHubRepeaterPortGroup OBJECT-GROUP OBJECTS { cssRepeaterPortName, cssRepeaterPortControllerRevision, cssRepeaterPortSpeedAdmin, cssRepeaterPortSpeedStatus, cssRepeaterPortLinkStatus } STATUS current DESCRIPTION "A collection of repeater port objects for use with the Cisco Stackable Dual-Speed Hub products." ::= { ciscoSibuStackableDualSpeedHubMIBGroups 2 } ciscoSibuStackableDualSpeedHubSwitchPortGroup OBJECT-GROUP OBJECTS { cssSwitchPortModuleID, cssSwitchPortPortID, cssSwitchPortName, cssSwitchPortType, cssSwitchPortControllerRevision, cssSwitchPortState, cssSwitchPortDuplexAdmin, cssSwitchPortDuplexStatus, cssSwitchPortSpeedAdmin, cssSwitchPortSpeedStatus, cssSwitchPortLinkStatus } STATUS current DESCRIPTION "A collection of switch module port objects for use with the Cisco Stackable Dual-Speed Hub products." ::= { ciscoSibuStackableDualSpeedHubMIBGroups 3 } END