| managementDomainIndex |
.1.3.6.1.4.1.9.9.46.1.2.1.1.1 |
|
An arbitrary value to uniquely identify the management
domain on the local system.
|
| managementDomainName |
.1.3.6.1.4.1.9.9.46.1.2.1.1.2 |
|
The management name of a domain in which the local system
is participating. The zero-length name corresponds to the
'no management-domain' state which is the initial value at
installation-time if not configured otherwise. Note that
the zero-length name does not correspond to an operational
management domain, and a device does not send VTP
advertisements while in the 'no management-domain' state. A
device leaves the 'no management-domain' state when it
obtains a management-domain name, either through
configuration or through inheriting the management-domain
name from a received VTP advertisement.
When the value of an existing instance of this object is
modified by network management, the local system should re-
initialize its VLAN information (for the given management
domain) as if it had just been configured with a management
domain name at installation time.
|
| managementDomainLocalMode |
.1.3.6.1.4.1.9.9.46.1.2.1.1.3 |
|
The local VTP mode in this management domain when
managementDomainVersionInUse is version1(1) or
version2(2).
If managementDomainVersionInUse is version3(4), this
object has the same value with vtpDatabaseLocalMode
of VLAN database type.
- 'client' indicates that the local system is acting
as a VTP client.
- 'server' indicates that the local system is acting
as a VTP server.
- 'transparent' indicates that the local system does
not generate or listen to VTP messages, but forwards
messages. This mode can also be set by the device
itself when the amount of VLAN information is too
large for it to hold in DRAM.
- 'off' indicates that the local system does not
generate, listen to or forward any VTP messages.
|
| managementDomainConfigRevNumber |
.1.3.6.1.4.1.9.9.46.1.2.1.1.4 |
|
The current Configuration Revision Number as known by
the local device for this management domain when
managementDomainVersionInUse is version1(1) or
version2(2).
If managementDomainVersionInUse is version3(4), this
object has the same value with vtpDatabaseRevisionNumber
of VLAN database type.
This value is updated (if necessary) whenever a VTP
advertisement is received or generated. When in the
'no management-domain' state, this value is 0.
|
| managementDomainLastUpdater |
.1.3.6.1.4.1.9.9.46.1.2.1.1.5 |
|
The IP-address (or one of them) of the VTP Server which
last updated the Configuration Revision Number, as indicated
in the most recently received VTP advertisement for this
management domain, when managementDomainVersionInUse is
version1(1) or version2(2).
If managementDomainVersionInUse is version3(4), this object
has the value of 0.0.0.0.
Before an advertisement has been received, this value is
0.0.0.0.
|
| managementDomainLastChange |
.1.3.6.1.4.1.9.9.46.1.2.1.1.6 |
|
The time at which the Configuration Revision Number was
(last) increased to its current value, as indicated in the
most recently received VTP advertisement for this management
domain when managementDomainVersionInUse is not version3(4)
or in the most recently received VTP VLAN database
advertisement for this management domain when
managementDomainVersionInUse is version3(4).
The value 0x0000010100000000 indicates that the device which
last increased the Configuration Revision Number had no idea
of the date/time, or that no advertisement has been
received.
|
| managementDomainRowStatus |
.1.3.6.1.4.1.9.9.46.1.2.1.1.7 |
|
The status of this conceptual row.
|
| managementDomainTftpServer |
.1.3.6.1.4.1.9.9.46.1.2.1.1.8 |
|
The IP address of a TFTP Server in/from which VTP VLAN
information for this management domain is to be
stored/retrieved. If the information is being locally
stored in NVRAM, this object should take the value 0.0.0.0.
|
| managementDomainTftpPathname |
.1.3.6.1.4.1.9.9.46.1.2.1.1.9 |
|
The complete pathname of the file at the TFTP Server
identified by the value of managementDomainTftpServer
in/from which VTP VLAN information for this management
domain is to be stored/retrieved. If the value of
corresponding instance of managementDomainTftpServer is
0.0.0.0, the value of this object is ignored.
|
| managementDomainPruningState |
.1.3.6.1.4.1.9.9.46.1.2.1.1.10 |
|
An indication of whether VTP pruning is enabled or disabled
in this managament domain. This value can only be modified
by local/network management when the value of the
corresponding instance of managementDomainLocalMode is
'server'.
|
| managementDomainVersionInUse |
.1.3.6.1.4.1.9.9.46.1.2.1.1.11 |
|
The current version of the VTP that is in use by the
designated management domain.
This object can be set to none(3) only when
vtpVersion is none(3).
|
| vtpVlanIndex |
.1.3.6.1.4.1.9.9.46.1.3.1.1.1 |
|
The VLAN-id of this VLAN on ISL or 802.1q trunks.
|
| vtpVlanState |
.1.3.6.1.4.1.9.9.46.1.3.1.1.2 |
|
The state of this VLAN.
The state 'mtuTooBigForDevice' indicates that this device
cannot participate in this VLAN because the VLAN's MTU is
larger than the device can support.
The state 'mtuTooBigForTrunk' indicates that while this
VLAN's MTU is supported by this device, it is too large for
one or more of the device's trunk ports.
|
| vtpVlanType |
.1.3.6.1.4.1.9.9.46.1.3.1.1.3 |
|
The type of this VLAN.
|
| vtpVlanName |
.1.3.6.1.4.1.9.9.46.1.3.1.1.4 |
|
The name of this VLAN. This name is used as the ELAN-name
for an ATM LAN-Emulation segment of this VLAN.
|
| vtpVlanMtu |
.1.3.6.1.4.1.9.9.46.1.3.1.1.5 |
|
The MTU size on this VLAN, defined as the size of largest
MAC-layer (information field portion of the) data frame
which can be transmitted on the VLAN.
|
| vtpVlanDot10Said |
.1.3.6.1.4.1.9.9.46.1.3.1.1.6 |
|
The value of the 802.10 SAID field for this VLAN.
|
| vtpVlanRingNumber |
.1.3.6.1.4.1.9.9.46.1.3.1.1.7 |
|
The ring number of this VLAN. This object is only
instantiated when the value of the corresponding instance of
vtpVlanType has a value of 'fddi' or 'tokenRing' and Source
Routing is in use on this VLAN.
|
| vtpVlanBridgeNumber |
.1.3.6.1.4.1.9.9.46.1.3.1.1.8 |
|
The bridge number of the VTP-capable switches for this
VLAN. This object is only instantiated for VLANs that are
involved with emulating token ring segments.
|
| vtpVlanStpType |
.1.3.6.1.4.1.9.9.46.1.3.1.1.9 |
|
The type of the Spanning Tree Protocol (STP) running on
this VLAN. This object is only instanciated when the
value of the corresponding instance of vtpVlanType has a
value of 'fddiNet' or 'trNet'.
The value returned by this object depends upon the value
of the corresponding instance of vtpVlanEditStpType.
- 'ieee' indicates IEEE STP is running exclusively.
- 'ibm' indicates IBM STP is running exclusively.
- 'hybrid' indicates a STP that allows a combination of
IEEE and IBM is running.
The 'hybrid' STP type results from tokenRing/fddi VLANs
that are children of this trNet/fddiNet parent VLAN being
configured in a combination of SRT and SRB
vtpVlanBridgeTypes while the instance of
vtpVlanEditStpType that corresponds to this object is set
to 'auto'.
|
| vtpVlanParentVlan |
.1.3.6.1.4.1.9.9.46.1.3.1.1.10 |
|
The parent VLAN for this VLAN. This object is only
instantiated when the value of the corresponding instance of
vtpVlanType has a value of 'fddi' or 'tokenRing' and Source
Routing is in use on this VLAN. The parent VLAN must have
a vtpVlanType value of fddiNet(4) or trNet(5),
respectively.
|
| vtpVlanTranslationalVlan1 |
.1.3.6.1.4.1.9.9.46.1.3.1.1.11 |
|
A VLAN to which this VLAN is being translational-bridged.
If this value and the corresponding instance of
vtpVlanTranslationalVlan2 are both zero, then this VLAN is
not being translational-bridged.
|
| vtpVlanTranslationalVlan2 |
.1.3.6.1.4.1.9.9.46.1.3.1.1.12 |
|
Another VLAN, i.e., other than that indicated by
vtpVlanTranslationalVlan1, to which this VLAN is being
translational-bridged. If this value and the corresponding
instance of vtpVlanTranslationalVlan1 are both zero, then
this VLAN is not being translational-bridged.
|
| vtpVlanBridgeType |
.1.3.6.1.4.1.9.9.46.1.3.1.1.13 |
|
The type of the Source Route bridging mode in use on this
VLAN. This object is only instantiated when the value of
the corresponding instance of vtpVlanType has a value of
fddi(2) or tokenRing(3) and Source Routing is in use on
this VLAN.
|
| vtpVlanAreHopCount |
.1.3.6.1.4.1.9.9.46.1.3.1.1.14 |
|
The maximum number of bridge hops allowed in
All Routes Explorer frames on this VLAN. This
object is only instantiated when the value of the
corresponding instance of vtpVlanType has a value of fddi(2)
or tokenRing(3) and Source Routing is in use on this VLAN.
|
| vtpVlanSteHopCount |
.1.3.6.1.4.1.9.9.46.1.3.1.1.15 |
|
The maximum number of bridge hops allowed in
Spanning Tree Explorer frames on this VLAN. This
object is only instantiated when the value of the
corresponding instance of vtpVlanType has a value of fddi(2)
or tokenRing(3) and Source Routing is in use on this VLAN.
|
| vtpVlanIsCRFBackup |
.1.3.6.1.4.1.9.9.46.1.3.1.1.16 |
|
True if this VLAN is of type trCrf and also is acting as
a backup trCrf for the ISL distributed BRF
|
| vtpVlanTypeExt |
.1.3.6.1.4.1.9.9.46.1.3.1.1.17 |
|
The additional type information of this VLAN.
|
| vtpVlanIfIndex |
.1.3.6.1.4.1.9.9.46.1.3.1.1.18 |
|
The value of the ifIndex corresponding to this VLAN ID.
If the VLAN ID does not have its corresponding interface,
this object has the value of zero.
|
| vtpInternalVlanOwner |
.1.3.6.1.4.1.9.9.46.1.3.2.2.1.1 |
|
The program name of the internal VLAN's
owner application. This internal VLAN
is allocated by the device specifically
for this application and no one else
could create, modify or delete this
VLAN.
|
| vtpVlanEditOperation |
.1.3.6.1.4.1.9.9.46.1.4.1.1.1 |
|
This object always has the value 'none' when read. When
written, each value causes the appropriate action:
'copy' - causes the creation of rows in the
vtpVlanEditTable exactly corresponding to the current global
VLAN information for this management domain. If the Edit
Buffer (for this management domain) is not currently empty,
a copy operation fails. A successful copy operation starts
the deadman-timer.
'apply' - first performs a consistent check on the the
modified information contained in the Edit Buffer, and if
consistent, then tries to instanciate the modified
information as the new global VLAN information. Note that
an empty Edit Buffer (for the management domain) would
always result in an inconsistency since the default VLANs
are required to be present.
'release' - flushes the Edit Buffer (for this management
domain), clears the Owner information, and aborts the
deadman-timer. A release is generated automatically if the
deadman-timer ever expires.
'restartTimer' - restarts the deadman-timer.
'none' - no operation is performed.
|
| vtpVlanApplyStatus |
.1.3.6.1.4.1.9.9.46.1.4.1.1.2 |
|
The current status of an 'apply' operation to instanciate
the Edit Buffer as the new global VLAN information (for this
management domain). If no apply is currently active, the
status represented is that of the most recently completed
apply. The possible values are:
inProgress - 'apply' operation in progress;
succeeded - the 'apply' was successful (this value is
also used when no apply has been invoked since the
last time the local system restarted);
configNumberError - the apply failed because the value of
vtpVlanEditConfigRevNumber was less or equal to
the value of current value of
managementDomainConfigRevNumber;
inconsistentEdit - the apply failed because the modified
information was not self-consistent;
tooBig - the apply failed because the modified
information was too large to fit in this VTP
Server's non-volatile storage location;
localNVStoreFail - the apply failed in trying to store
the new information in a local non-volatile
storage location;
remoteNVStoreFail - the apply failed in trying to store
the new information in a remote non-volatile
storage location;
editBufferEmpty - the apply failed because the Edit
Buffer was empty (for this management domain).
someOtherError - the apply failed for some other reason
(e.g., insufficient memory).
notPrimaryServer - the apply failed because the local
device is not a VTP primary server for VLAN
database type when managementDomainVersionInUse
is version3(4).
|
| vtpVlanEditBufferOwner |
.1.3.6.1.4.1.9.9.46.1.4.1.1.3 |
|
The management station which is currently using the Edit
Buffer for this management domain. When the Edit Buffer for
a management domain is not currently in use, the value of
this object is the zero-length string. Note that it is also
the zero-length string if a manager fails to set this object
when invoking a copy operation.
|
| vtpVlanEditConfigRevNumber |
.1.3.6.1.4.1.9.9.46.1.4.1.1.4 |
|
The Configuration Revision Number to be used for the next
apply operation. This value is initialized (by the agent)
on a copy operation to be one greater than the value of
managementDomainConfigRevNumber. On an apply, if the
number is less or equal to the value of
managementDomainConfigRevNumber, then the apply fails.
The value can be modified (increased) by network management
before an apply to ensure that an apply does not fail for
this reason.
This object is used to allow management control over whether
a configuration revision received via a VTP advertisement
after a copy operation but before the succeeding apply
operation is lost by being overwritten by the (local) edit
operation. By default, the apply operation will fail in
this situation. By increasing this object's value after the
copy but before the apply, management can control whether
the apply is to succeed (with the update via VTP
advertisement being lost).
|
| vtpVlanEditModifiedVlan |
.1.3.6.1.4.1.9.9.46.1.4.1.1.5 |
|
The VLAN-id of the modified VLAN in the Edit Buffer.
If the object has the value of zero, any VLAN can
be edited. If the value of the object is not zero,
only this VLAN can be edited.
The object's value is reset to zero after a successful
'apply' operation or a 'release' operation.
This object is only supported for devices which allow
only one VLAN editing for each 'apply' operation. For
devices which allow multiple VLAN editing for each
'apply' operation, this object is not supported.
|
| vtpVlanEditIndex |
.1.3.6.1.4.1.9.9.46.1.4.2.1.1 |
|
The VLAN-id which this VLAN would have on ISL or
802.1q trunks.
|
| vtpVlanEditState |
.1.3.6.1.4.1.9.9.46.1.4.2.1.2 |
|
The state which this VLAN would have.
|
| vtpVlanEditType |
.1.3.6.1.4.1.9.9.46.1.4.2.1.3 |
|
The type which this VLAN would have.
An implementation may restrict access to this object.
|
| vtpVlanEditName |
.1.3.6.1.4.1.9.9.46.1.4.2.1.4 |
|
The name which this VLAN would have. This name would be
used as the ELAN-name for an ATM LAN-Emulation segment of
this VLAN.
An implementation may restrict access to this object.
|
| vtpVlanEditMtu |
.1.3.6.1.4.1.9.9.46.1.4.2.1.5 |
|
The MTU size which this VLAN would have, defined as the
size of largest MAC-layer (information field portion of the)
data frame which can be transmitted on the VLAN.
An implementation may restrict access to this object.
|
| vtpVlanEditDot10Said |
.1.3.6.1.4.1.9.9.46.1.4.2.1.6 |
|
The value of the 802.10 SAID field which would be used for
this VLAN.
An implementation may restrict access to this object.
|
| vtpVlanEditRingNumber |
.1.3.6.1.4.1.9.9.46.1.4.2.1.7 |
|
The ring number which would be used for this VLAN. This
object is only instantiated when the value of the
corresponding instance of vtpVlanEditType has a value of
'fddi' or 'tokenRing' and Source Routing is in use on
this VLAN.
|
| vtpVlanEditBridgeNumber |
.1.3.6.1.4.1.9.9.46.1.4.2.1.8 |
|
The bridge number of the VTP-capable switches which would
be used for this VLAN. This object is only instantiated
when the value of the corresponding instance of
vtpVlanEditType has a value of fddiNet(4) or trNet(5).
|
| vtpVlanEditStpType |
.1.3.6.1.4.1.9.9.46.1.4.2.1.9 |
|
The type of the Spanning Tree Protocol which would be
running on this VLAN. This object is only instantiated
when the value of the corresponding instance of
vtpVlanEditType has a value of fddiNet(4) or trNet(5).
If 'ieee' is selected, the STP that runs will be IEEE.
If 'ibm' is selected, the STP that runs will be IBM.
If 'auto' is selected, the STP that runs will be
dependant on the values of vtpVlanEditBridgeType for all
children tokenRing/fddi type VLANs. This will result in
a 'hybrid' STP (see vtpVlanStpType).
|
| vtpVlanEditParentVlan |
.1.3.6.1.4.1.9.9.46.1.4.2.1.10 |
|
The VLAN index of the VLAN which would be the parent for
this VLAN. This object is only instantiated when the value
of the corresponding instance of vtpVlanEditType has a value
of 'fddi' or 'tokenRing' and Source Routing is in use on
this VLAN. The parent VLAN must have a vtpVlanEditType
value of fddiNet(4) or trNet(5), respectively.
|
| vtpVlanEditRowStatus |
.1.3.6.1.4.1.9.9.46.1.4.2.1.11 |
|
The status of this row. Any and all columnar objects in an
existing row can be modified irrespective of the status of
the row.
A row is not qualified for activation until instances of at
least its vtpVlanEditType, vtpVlanEditName and
vtpVlanEditDot10Said columns have appropriate values.
The management station should endeavor to make all rows
consistent in the table before 'apply'ing the buffer. An
inconsistent entry in the table will cause the entire
buffer to be rejected with the vtpVlanApplyStatus object
set to the appropriate error value.
|
| vtpVlanEditTranslationalVlan1 |
.1.3.6.1.4.1.9.9.46.1.4.2.1.12 |
|
A VLAN to which this VLAN would be translational-bridged.
If this value and the corresponding instance of
vtpVlanTranslationalVlan2 are both zero, then this VLAN
would not be translational-bridged.
An implementation may restrict access to this object.
|
| vtpVlanEditTranslationalVlan2 |
.1.3.6.1.4.1.9.9.46.1.4.2.1.13 |
|
Another VLAN, i.e., other than that indicated by
vtpVlanEditTranslationalVlan1, to which this VLAN would be
translational-bridged. If this value and the corresponding
instance of vtpVlanTranslationalVlan1 are both zero, then
this VLAN would not be translational-bridged.
An implementation may restrict access to this object.
|
| vtpVlanEditBridgeType |
.1.3.6.1.4.1.9.9.46.1.4.2.1.14 |
|
The type of Source Route bridging mode which would be in
use on this VLAN. This object is only instantiated when
the value of the corresponding instance of vtpVlanEditType
has a value of fddi(2) or tokenRing(3) and Source Routing
is in use on this VLAN.
|
| vtpVlanEditAreHopCount |
.1.3.6.1.4.1.9.9.46.1.4.2.1.15 |
|
The maximum number of bridge hops allowed in
All Routes Explorer frames on this VLAN. This
object is only instantiated when the value of the
corresponding instance of vtpVlanType has a value of fddi(2)
or tokenRing(3) and Source Routing is in use on this VLAN.
|
| vtpVlanEditSteHopCount |
.1.3.6.1.4.1.9.9.46.1.4.2.1.16 |
|
The maximum number of bridge hops allowed in
Spanning Tree Explorer frames on this VLAN. This
object is only instantiated when the value of the
corresponding instance of vtpVlanType has a value of fddi(2)
or tokenRing(3) and Source Routing is in use on this VLAN.
|
| vtpVlanEditIsCRFBackup |
.1.3.6.1.4.1.9.9.46.1.4.2.1.17 |
|
True if this VLAN is of type trCrf and also is acting as
a backup trCrf for the ISL distributed BRF. This object is
only instantiated when the value of the corresponding
instance of vtpVlanEditType has a value of tokenRing(3).
|
| vtpVlanEditTypeExt |
.1.3.6.1.4.1.9.9.46.1.4.2.1.18 |
|
The additional type information of this VLAN.
|
| vtpVlanEditTypeExt2 |
.1.3.6.1.4.1.9.9.46.1.4.2.1.19 |
|
The additional type information of this VLAN.
The VlanTypeExt TC specifies which bits may
be written by a management application.
The agent should provide a default value.
|
| vtpInSummaryAdverts |
.1.3.6.1.4.1.9.9.46.1.5.1.1.1 |
|
The total number of VTP Summary Adverts received for this
management domain.
|
| vtpInSubsetAdverts |
.1.3.6.1.4.1.9.9.46.1.5.1.1.2 |
|
The total number of VTP Subset Adverts received for this
management domain.
|
| vtpInAdvertRequests |
.1.3.6.1.4.1.9.9.46.1.5.1.1.3 |
|
The total number of VTP Advert Requests received for this
management domain.
|
| vtpOutSummaryAdverts |
.1.3.6.1.4.1.9.9.46.1.5.1.1.4 |
|
The total number of VTP Summary Adverts sent for this
management domain.
|
| vtpOutSubsetAdverts |
.1.3.6.1.4.1.9.9.46.1.5.1.1.5 |
|
The total number of VTP Subset Adverts sent for this
management domain.
|
| vtpOutAdvertRequests |
.1.3.6.1.4.1.9.9.46.1.5.1.1.6 |
|
The total number of VTP Advert Requests sent for this
management domain.
|
| vtpConfigRevNumberErrors |
.1.3.6.1.4.1.9.9.46.1.5.1.1.7 |
|
The number of occurrences of configuration revision number
errors for this management domain. A configuration revision
number error occurs when a device receives a VTP
advertisement for which:
- the advertisement's Configuration Revision Number is the
same as the current locally-held value, and
- the advertisement's digest value is different from the
current locally-held value.
|
| vtpConfigDigestErrors |
.1.3.6.1.4.1.9.9.46.1.5.1.1.8 |
|
The number of occurrences of configuration digest errors
for this management domain. A configuration digest error
occurs when a device receives a VTP advertisement for which:
- the advertisement's Configuration Revision Number is
greater than the current locally-held value, and
- the advertisement's digest value does not match the VLAN
information assumed by the receiver of the advertisement,
where the infomation assumed is the combination of the
information explicitly contained in the advertisement plus
any omitted information as currently known by the
receiving device.
|
| vlanTrunkPortIfIndex |
.1.3.6.1.4.1.9.9.46.1.6.1.1.1 |
|
The value of ifIndex for the interface corresponding to
this trunk port.
|
| vlanTrunkPortManagementDomain |
.1.3.6.1.4.1.9.9.46.1.6.1.1.2 |
|
The value of managementDomainIndex for the management
domain on this trunk port. Devices which support only one
management domain will support this object read-only.
|
| vlanTrunkPortEncapsulationType |
.1.3.6.1.4.1.9.9.46.1.6.1.1.3 |
|
The type of VLAN encapsulation desired to be used on this
trunk port. It is either a particular type, or 'negotiate'
meaning whatever type results from the negotiation.
negotiate(5) is not allowed if the port does not support
negotiation or if its vlanTrunkPortDynamicState is set to
on(1) or onNoNegotiate(5). Whether writing to this object
in order to modify the encapsulation is supported is both
device and interface specific.
|
| vlanTrunkPortVlansEnabled |
.1.3.6.1.4.1.9.9.46.1.6.1.1.4 |
|
A string of octets containing one bit per VLAN in the
management domain on this trunk port. The first octet
corresponds to VLANs with VlanIndex values of 0 through 7;
the second octet to VLANs 8 through 15; etc. The most
significant bit of each octet corresponds to the lowest
value VlanIndex in that octet. If the bit corresponding to
a VLAN is set to '1', then the local system is enabled for
sending and receiving frames on that VLAN; if the bit is set
to '0', then the system is disabled from sending and
receiving frames on that VLAN.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vlanTrunkPortNativeVlan |
.1.3.6.1.4.1.9.9.46.1.6.1.1.5 |
|
The VlanIndex of the VLAN which is represented by native
frames on this trunk port. For trunk ports not supporting
the sending and receiving of native frames, this value
should be set to zero.
|
| vlanTrunkPortRowStatus |
.1.3.6.1.4.1.9.9.46.1.6.1.1.6 |
|
The status of this row. In some circumstances, the
creation of a row in this table is needed to enable the
appropriate trunking/tagging protocol on the port, to enable
the use of VTP on the port, and to assign the port to the
appropriate management domain. In other circumstances, rows
in this table will be created as a by-product of other
operations.
|
| vlanTrunkPortInJoins |
.1.3.6.1.4.1.9.9.46.1.6.1.1.7 |
|
The number of VTP Join messages received on this trunk
port.
|
| vlanTrunkPortOutJoins |
.1.3.6.1.4.1.9.9.46.1.6.1.1.8 |
|
The number of VTP Join messages sent on this trunk port.
|
| vlanTrunkPortOldAdverts |
.1.3.6.1.4.1.9.9.46.1.6.1.1.9 |
|
The number of VTP Advertisement messages which indicated
the sender does not support VLAN-pruning received on this
trunk port.
|
| vlanTrunkPortVlansPruningEligible |
.1.3.6.1.4.1.9.9.46.1.6.1.1.10 |
|
A string of octets containing one bit per VLAN in the
management domain on this trunk port. The first octet
corresponds to VLANs with VlanIndex values of 0 through 7;
the second octet to VLANs 8 through 15; etc. The most
significant bit of each octet corresponds to the lowest
value VlanIndex in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local system is permitted to prune that VLAN on this trunk
port; if the bit is set to '0', then the system must not
prune that VLAN on this trunk port.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vlanTrunkPortVlansXmitJoined |
.1.3.6.1.4.1.9.9.46.1.6.1.1.11 |
|
A string of octets containing one bit per VLAN in the
management domain on this trunk port. The first octet
corresponds to VLANs with VlanIndex values of 0 through 7;
the second octet to VLANs 8 through 15; etc. The most
significant bit of each octet corresponds to the lowest
value VlanIndex in that octet.
If the bit corresponding to a VLAN is set to '1', then this
VLAN is presently being forwarded on this trunk port, i.e.,
it is not pruned; if the bit is set to '0', then this VLAN
is presently not being forwarded on this trunk port, either
because it is pruned or for some other reason.
|
| vlanTrunkPortVlansRcvJoined |
.1.3.6.1.4.1.9.9.46.1.6.1.1.12 |
|
A string of octets containing one bit per VLAN in the
management domain on this trunk port. The first octet
corresponds to VLANs with VlanIndex values of 0 through 7;
the second octet to VLANs 8 through 15; etc. The most
significant bit of each octet corresponds to the lowest
value VlanIndex in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local switch is currently sending joins for this VLAN on
this trunk port, i.e., it is asking to receive frames for
this VLAN; if the bit is set to '0', then the local switch
is not currently sending joins for this VLAN on this trunk
port.
|
| vlanTrunkPortDynamicState |
.1.3.6.1.4.1.9.9.46.1.6.1.1.13 |
|
For devices that allows dynamic determination of whether
a link between two switches should be a trunk or not, this
object allows the operator to mandate the behavior of that
dynamic mechanism.
on(1) dictates that the interface will always be a
trunk. This is the value for static entries (those that
show no dynamic behavior). If the negotiation is supported
on this port, negotiation will take place with the far end
to attempt to bring the far end into trunking state.
off(2) allows an operator to specify that the specified
interface is never to be trunk, regardless of any dynamic
mechanisms to the contrary. This value is useful for
overriding the default behavior of some switches. If the
negotiation is supported on this port, negotiation will take
place with the far end to attempt on the link to bring the
far end into non-trunking state.
desirable(3) is used to indicate that it is desirable for
the interface to become a trunk. The device will initiate
any negotiation necessary to become a trunk but will not
become a trunk unless it receives confirmation from the far
end on the link.
auto(4) is used to indicate that the interface is capable
and willing to become a trunk but will not initiate
trunking negotiations. The far end on the link are
required to either start negotiations or start sending
encapsulated packets, on which event the specified
interface will become a trunk.
onNoNegotiate(5) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If the port does not support negotiation or its
vlanTrunkPortEncapsulationType is set to negotiate(5),
onNoNegotiate(5) is not allowed.
Devices that do no support dynamic determination (for just
a particular interface, encapsulation or for the whole
device) need only support the 'on', and 'off' values.
|
| vlanTrunkPortDynamicStatus |
.1.3.6.1.4.1.9.9.46.1.6.1.1.14 |
|
Indicates whether the specified interface is either
acting as a trunk or not. This is a result of the
vlanTrunkPortDynamicState and the ifOperStatus of the
trunk port itself.
|
| vlanTrunkPortVtpEnabled |
.1.3.6.1.4.1.9.9.46.1.6.1.1.15 |
|
Some trunk interface modules allow VTP to be
enabled/disabled seperately from that of the central
device. In such a case this object provides management a
way to remotely enable VTP on that module. If a module
does not support a seperate VTP enabled state then this
object shall always return 'true' and will accept no other
value during a SET operation.
|
| vlanTrunkPortEncapsulationOperType |
.1.3.6.1.4.1.9.9.46.1.6.1.1.16 |
|
The type of VLAN encapsulation in use on this trunk port.
For intefaces with vlanTrunkPortDynamicStatus of
notTrunking(2) the vlanTrunkPortEncapsulationOperType shall
be notApplicable(6).
|
| vlanTrunkPortVlansEnabled2k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.17 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 1024 through 2047 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 1024 through 1031; the second
octet to VLANs 1032 through 1039; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet. If the bit corresponding to a VLAN is set to
'1', then the local system is enabled for sending and
receiving frames on that VLAN; if the bit is set to '0',
then the system is disabled from sending and receiving
frames on that VLAN. The default value is zero length
string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vlanTrunkPortVlansEnabled3k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.18 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 2048 through 3071 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 2048 through 2055; the second
octet to VLANs 2056 through 2063; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet. If the bit corresponding to a VLAN is set to
'1', then the local system is enabled for sending and
receiving frames on that VLAN; if the bit is set to '0',
then the system is disabled from sending and receiving
frames on that VLAN. The default value is zero length
string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vlanTrunkPortVlansEnabled4k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.19 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 3072 through 4095 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 3072 through 3079; the second
octet to VLANs 3080 through 3087; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet. If the bit corresponding to a VLAN is set to
'1', then the local system is enabled for sending and
receiving frames on that VLAN; if the bit is set to '0',
then the system is disabled from sending and receiving
frames on that VLAN. The default value is zero length
string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vtpVlansPruningEligible2k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.20 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 1024 through 2047 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 1024 through 1031; the second
octet to VLANs 1032 through 1039; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local system is permitted to prune that VLAN on this trunk
port; if the bit is set to '0', then the system must not
prune that VLAN on this trunk port.
The default value is zero length string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vtpVlansPruningEligible3k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.21 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 2048 through 3071 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 2048 through 2055; the second
octet to VLANs 2056 through 2063; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local system is permitted to prune that VLAN on this trunk
port; if the bit is set to '0', then the system must not
prune that VLAN on this trunk port.
The default value is zero length string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vtpVlansPruningEligible4k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.22 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 3072 through 4095 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 3072 through 3079; the second
octet to VLANs 3080 through 3087; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local system is permitted to prune that VLAN on this trunk
port; if the bit is set to '0', then the system must not
prune that VLAN on this trunk port.
The default value is zero length string.
To avoid conflicts between overlapping partial updates by
multiple managers, i.e., updates which modify only a portion
of an instance of this object (e.g., enable/disable a single
VLAN on the trunk port), any SNMP Set operation accessing an
instance of this object should also write the value of
vlanTrunkPortSetSerialNo.
|
| vlanTrunkPortVlansXmitJoined2k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.23 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 1024 through 2047 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 1024 through 1031; the second
octet to VLANs 1032 through 1039; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then this
VLAN is presently being forwarded on this trunk port, i.e.,
it is not pruned; if the bit is set to '0', then this VLAN
is presently not being forwarded on this trunk port, either
because it is pruned or for some other reason.
|
| vlanTrunkPortVlansXmitJoined3k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.24 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 2048 through 3071 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 2048 through 2055; the second
octet to VLANs 2056 through 2063; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then this
VLAN is presently being forwarded on this trunk port, i.e.,
it is not pruned; if the bit is set to '0', then this VLAN
is presently not being forwarded on this trunk port, either
because it is pruned or for some other reason.
|
| vlanTrunkPortVlansXmitJoined4k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.25 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 3072 through 4095 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 3072 through 3079; the second
octet to VLANs 3080 through 3087; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then this
VLAN is presently being forwarded on this trunk port, i.e.,
it is not pruned; if the bit is set to '0', then this VLAN
is presently not being forwarded on this trunk port, either
because it is pruned or for some other reason.
|
| vlanTrunkPortVlansRcvJoined2k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.26 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 1024 through 2047 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 1024 through 1031; the second
octet to VLANs 1032 through 1039; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local switch is currently sending joins for this VLAN on
this trunk port, i.e., it is asking to receive frames for
this VLAN; if the bit is set to '0', then the local switch
is not currently sending joins for this VLAN on this trunk
port.
|
| vlanTrunkPortVlansRcvJoined3k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.27 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 2048 through 3071 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 2048 through 2055; the second
octet to VLANs 2056 through 2063; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local switch is currently sending joins for this VLAN on
this trunk port, i.e., it is asking to receive frames for
this VLAN; if the bit is set to '0', then the local switch
is not currently sending joins for this VLAN on this trunk
port.
|
| vlanTrunkPortVlansRcvJoined4k |
.1.3.6.1.4.1.9.9.46.1.6.1.1.28 |
|
A string of octets containing one bit per VLAN for VLANS
with VlanIndex values of 3072 through 4095 in the management
domain on this trunk port. The first octet corresponds to
VLANs with VlanIndex values of 3072 through 3079; the second
octet to VLANs 3080 through 3087; etc. The most significant
bit of each octet corresponds to the lowest value VlanIndex
in that octet.
If the bit corresponding to a VLAN is set to '1', then the
local switch is currently sending joins for this VLAN on
this trunk port, i.e., it is asking to receive frames for
this VLAN; if the bit is set to '0', then the local switch
is not currently sending joins for this VLAN on this trunk
port.
|
| vlanTrunkPortDot1qTunnel |
.1.3.6.1.4.1.9.9.46.1.6.1.1.29 |
|
Indicates dot1qtunnel mode of the port.
If the portDot1qTunnel is set to 'trunk' mode, the port's
vlanTrunkPortDynamicState will be changed to 'onNoNegotiate'
and the vlanTrunkPortEncapsulationType will be set to
'dot1Q'. These values cannot be changed unless dot1q tunnel
is disabled on this port.
If the portDot1qTunnel mode is set to 'access' mode, the
port's vlanTrunkPortDynamicState will be set to 'off'.And
the value of vlanTrunkPortDynamicState cannot be changed
unless dot1q tunnel is disabled on this port. 1Q packets
received on this access port will remain.
Setting the port to dot1q tunnel 'disabled' mode causes the
dot1q tunnel feature to be disabled on this port. This
object can't be set to 'trunk' or 'access' mode, when
vlanTrunkPortsDot1qTag object is set to 'false'.
This object has been deprecated and is replaced by the
object 'cltcDot1qTunnelMode' in the
CISCO-L2-TUNNEL-CONFIG-MIB
|
| vtpDiscoverAction |
.1.3.6.1.4.1.9.9.46.1.7.1.1.1 |
|
When this object is set to discover(1), all the
entries in vtpDiscoverResultTable for the
corresponding management domain will be removed
and the local device will begin to discover all
VTP members in the management domain. Upon the
successful completion of discovery, the discovered
result will be stored in the vtpDiscoverResultTable.
If vtpDiscoverStatus is inProgress(1), setting
vtpDiscoverAction to discover(1) will fail.
When this object is set to purgeResult(3),
all the entries of vtpDiscoverResultTable for
the corresponding management domain will be
removed from vtpDiscoverResultTable.
When this object is set to noOperation(2), no
action will be taken. When read, this object
always returns noOperation(2).
|
| vtpDiscoverStatus |
.1.3.6.1.4.1.9.9.46.1.7.1.1.2 |
|
The current status of VTP discovery.
inProgress - a discovery is in progress;
succeeded - the discovery was completed successfully
(this value is also used when
no discover has been invoked since the
last time the local system restarted);
resourceUnavailable - the discovery failed because
the required allocation of a resource is
presently unavailable.
someOtherError - 'the discovery failed due to a
reason no listed.
|
| vtpLastDiscoverTime |
.1.3.6.1.4.1.9.9.46.1.7.1.1.3 |
|
The value of sysUpTime at which the last discovery
was completed.
A value of zero indicates that no discovery has been
invoked since last time the local system restarted.
|
| vtpDiscoverResultIndex |
.1.3.6.1.4.1.9.9.46.1.7.2.1.1 |
|
A value assigned by the system which identifies
a VTP member and the associated database in the
management domain.
|
| vtpDiscoverResultDatabaseName |
.1.3.6.1.4.1.9.9.46.1.7.2.1.2 |
|
The database name associated with the
discovered VTP member.
|
| vtpDiscoverResultConflicting |
.1.3.6.1.4.1.9.9.46.1.7.2.1.3 |
|
Indicates whether this VTP member contains
conflicting information.
true(1) indicates that this member has conflicting
information of the database type in the management domain.
false(2) indicates that there is no conflicting information
of the database type in the management domain.
|
| vtpDiscoverResultDeviceId |
.1.3.6.1.4.1.9.9.46.1.7.2.1.4 |
|
The unique identifier of the device for this VTP member.
|
| vtpDiscoverResultPrimaryServer |
.1.3.6.1.4.1.9.9.46.1.7.2.1.5 |
|
The unique identifier of the primary server for this VTP
member and the associated database type.
There are two different VTP servers, the primary server
and the secondary server. When a local device is
configured as a server for a certain database type,
it becomes secondary server by default.
Primary server is an operational role under which a
server can initiate or change the VTP configuration of the
database type.
If this VTP member itself is the primary server, the
value of this object is the same as the value of
vtpDiscoverResultDeviceId of the instance.
|
| vtpDiscoverResultRevNumber |
.1.3.6.1.4.1.9.9.46.1.7.2.1.6 |
|
The current configuration revision number as known by the
VTP member. When the database type is unknown for
the VTP member, this value is 0.
|
| vtpDiscoverResultSystemName |
.1.3.6.1.4.1.9.9.46.1.7.2.1.7 |
|
sysName of the VTP member.
|
| vtpDatabaseIndex |
.1.3.6.1.4.1.9.9.46.1.8.1.1.1 |
|
A value assigned by the system which uniquely identifies
a VTP database in the local system.
|
| vtpDatabaseName |
.1.3.6.1.4.1.9.9.46.1.8.1.1.2 |
|
The name of the database.
|
| vtpDatabaseLocalMode |
.1.3.6.1.4.1.9.9.46.1.8.1.1.3 |
|
The local VTP mode for a particular database type
in this administrative domain.
- 'client' indicates that the local system is acting
as a VTP client of the database type.
- 'server' indicates that the local system is acting
as a VTP server of the database type.
- 'transparent' indicates that the local system does
not generate or listen to VTP messages of this
database type, but forwards
messages. This mode can also be set by the device
itself when the size of database is too large for it
to hold in DRAM.
- 'off' indicates that the local system does not
generate, listen to or forward any VTP messages
of this database type.
The default mode is 'client' for the database type
known to the local device and 'transparent' for the
unknown database type.
|
| vtpDatabaseRevNumber |
.1.3.6.1.4.1.9.9.46.1.8.1.1.4 |
|
The current configuration revision number as known by the
local device for this VTP 3 database type in the management
domain. This value is updated (if necessary) whenever a
VTP advertisement for the database type is received
or generated. When the database type is unknown to the
local device or no VTP advertisement for the database
type is received or generated, its value is 0.
|
| vtpDatabasePrimaryServer |
.1.3.6.1.4.1.9.9.46.1.8.1.1.5 |
|
There are two kinds of VTP version 3 servers for a certain
database type - the primary server and the secondary server.
When a local device is configured as a server for a certain
database type, it becomes secondary server by default.
Primary server is an operational role under which a
server can initiate or change the VTP configuration of the
database type.
A true(1) value indicates that the local device is the
primary server of the database type in the management
domain. A false(2) value indicates that the local device
is not the primary server, or the database type is unknown
to the local device.
|
| vtpDatabasePrimaryServerId |
.1.3.6.1.4.1.9.9.46.1.8.1.1.6 |
|
The unique identifier of the primary server in the
management domain for the database type.
If no primary server is discovered for the database
type, the object has a value of zero length string.
|
| vtpDatabaseTakeOverPrimary |
.1.3.6.1.4.1.9.9.46.1.8.1.1.7 |
|
There are two kinds of VTP version 3 servers for a certain
database type - the primary server and the secondary server.
When a local device is configured as a server for a certain
database type, it becomes secondary server by default.
Primary server is an operational role under which a
server can initiate or change the VTP configuration of the
database type.
Setting this object to a true(1) value will advertise the
configuration of this database type to the whole domain.
In order to successfully setting this object to true(1),
the value of vtpDatabaseLocalMode must be server(2). Besides
that, when the VTP password is hidden from the configuration
file, the password (vtpDatabaseTakeOverPassword) which
matches the secret key (vtpAuthSecretKey) must be provided
in the same data packet.
When read, the object always returns false(2).
|
| vtpDatabaseTakeOverPassword |
.1.3.6.1.4.1.9.9.46.1.8.1.1.8 |
|
When read, this object always returns the value of a
zero-length octet string.
In the case that the VTP password is hidden from the
configuration and the local device intends
to take over the whole domain, this object must be
set to the matching password with the secret key
(vtpAuthSecretKey) in the same data packet as which
the vtpDatabaseTakeOverPrimary is in. In all the
other situations, setting a valid value to this object
has no impact on the system.
|
| vtpAuthPassword |
.1.3.6.1.4.1.9.9.46.1.9.1.1.1 |
|
By default, this object has a value of a zero-length
character string and is considered to be not
configured.
The device uses the password to generate the
secret key. It can be stored in the configuration in
plain text or hidden from the configuration. If a VTP
server intends to modify the database's configuration
in the domain but the password was hidden from the
configuration, the same password
(vtpDatabaseTakeOverPassword) as the hidden one
has to be provided.
When this object is set alone, vtpAuthPasswordType is
set to plaintext(1) automatically by the system.
Setting this object to a zero length character string
resets the password to its default value and the
password is considered as not configured.
This object is not allowed to be set at the same time
when vtpAuthSecretKey is set.
When the vtpAuthPasswordType is hidden(2), this object
will return a zero-length character string when read.
|
| vtpAuthPasswordType |
.1.3.6.1.4.1.9.9.46.1.9.1.1.2 |
|
By default this object has the value as plaintext(1)
and the VTP password is stored in the configuration
file in plain text.
Setting this object to hidden(2) will hide the
password from the configuration.
Once this object is set to hidden(2), it cannot
be set to plaintext(1) alone. However, it may
be set to plaintext(1) at the same time the
password is set.
|
| vtpAuthSecretKey |
.1.3.6.1.4.1.9.9.46.1.9.1.1.3 |
|
The device creating or modifying the VTP configuration
signs it using the MD5 digest generated from the secret
key before advertising it. Other devices in the domain
receiving this configuration use the same secret key
to accept it if it was correctly signed or drop it
otherwise.
By default, the object has the value as a zero-length
string and this value is read only. It is set
to this value automatically when the password
(vtpAuthPassword) is set to a zero-length octet string.
The secret key can be either generated using
the password or configured by the user. Once
the secret key is configured by the user, it is
stored as a hexadecimal string in the device's
configuration and the password is considered to be
the secret key's matching password and hidden
from the configuration automatically.
This object is not allowed to be set at the same
time when vtpAuthPassword is set.
The secret key is overwritten by a newly generated
secret key when the password is re-configured.
|
