| p2mpSelfTest |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.1 |
|
This object is used to enable/disable self test. When set to
true(1), the software tests the memory and hardware integrity
shortly after the router powers up.
|
| p2mpDiversityAntennaPresent |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.2 |
|
When true(1), this object indicates that a diversity
antenna is being used to receive the wireless transmissions.
When false(2), the radio system is using a single antenna
to transmit and receive.
|
| p2mpCableLoss |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.3 |
|
This object indicates the measured signal power loss in dB
due to the cable connecting the radio to the main antenna.
The hardware compensates for this cable loss by adjusting the
receive and transmit gain appropriately. A value of 0
indicates no degradation in the signal due to the cable. The
radio hardware can compensate for a cable loss of no more
than 15 db.
This cable loss applies to the main antenna only.
|
| p2mpCableLossDiversity |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.4 |
|
This object indicates the measured signal power loss in dB
due to the cable connecting the radio to the diversity
antenna. The hardware compensates for this loss by adjusting
the receive and transmit gain appropriately. A value of 0
indicates no degradation in the signal due to the cable. The
radio hardware can compensate for a cable loss of no more
than 15 dB.
This cable loss applies to the diversity antenna only.
|
| p2mpDenyService |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.5 |
|
Indicates if the service is disabled in the unit.
For Head-end unit, if this object has the value of
'true', the link is in loopback mode; otherwise the
link is enabled for transmitting / receiving data.
For Subscriber unit, if this object has the value of
'true', the subscriber unit service is disabled;
otherwise, the subscriber unit is enabled for
transmitting / receiving data
|
| p2mpClockRefExt |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.6 |
|
This object controls the use of external reference
clock for IF module as follows:
'true(1)' - an external reference clock is used
'false(2)' - an internal reference clock is used.
|
| p2mpCommonTrapEnable |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.7 |
|
When set to true(1), the notifications common to the head end
and subscriber unit are enabled. When set to false(2), these
notifications are disabled.
The notification controlled by this object are:
- p2mpRadioPhyFailNotification
- p2mpTrapRfSupplyVoltage
- p2mpTrapRfRxOsc
- p2mpTrapRfTxOsc
- p2mpTrapRfTemp
- p2mpTrapRfCommLinkError
- p2mpTrapTxPower
- p2mpTrapRfStatusChange
|
| p2mpLastPhyFailureType |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.8 |
|
This object indicates the last physical link failure that
resulted in a p2mpRadioPhyFailNotification trap.
none(1) - no failure
p2mpHwConfigUnsupported(2) - The radio subsystem has
detected that the configuration requested is not
supported by the hardware. The p2mpLastPhyFailureReason
variable will indicate which configuration parameter is
not supported.
p2mpHwConfigMismatch(3) - The radio subsystem has detected
that the combination of the configuration parameters
requested is inconsistent and cannot be supported.
The p2mpLastPhyFailReason variable will indicate the
configuration parameter that causes the mismatch.
p2mpHwInitFailure(4) - The radio subsystem has failed to
initialize the hardware. This implies that there is a
critical error condition in the associated hardware.
The p2mpLastPhyFailReason specifies the reason why the
init failed.
p2mpHostIfCommLinkError(5) - The host could not communicate
with the IF module.
p2mpAutoCableCompFailure(6) - Failed to achieve automatic
cable compensation due to loss of Tx signal.
|
| p2mpLastPhyFailureReason |
.1.3.6.1.4.1.9.9.170.1.1.1.1.1.9 |
|
This is a text string that describes the last physical link
failure identified by p2mpLastPhyFailureType.
|
| p2mpRfIndex |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.1 |
|
This object, along with the ifIndex of the MAC layer,
represents the index of this entry in the p2mpRfTable.
Each entry in the table provides details on the state of
the RF resources available in the system.
|
| p2mpRfType |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.2 |
|
This object identifies the RF resource.
|
| p2mpRfOpMode |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.3 |
|
This object specifies whether this RF resource can either
transmit, receive, or do both.
|
| p2mpTxFreqRangeMin |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.4 |
|
This object represents the minimum frequency at which this RF
resource can transmit.
|
| p2mpTxFreqRangeMax |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.5 |
|
This object represents the maximum frequency at which this RF
resource can transmit.
|
| p2mpRxFreqRangeMin |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.6 |
|
This object represents the lowest transmission frequency this
RF resource can receive.
|
| p2mpRxFreqRangeMax |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.7 |
|
This object represents the highest transmission frequency that
this RF resource can receive.
|
| p2mpMinTxPower |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.8 |
|
This object represents the minimum power that the RF subsystem
can supply the antenna.
|
| p2mpMaxTxPower |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.9 |
|
This object represents the maximum power that the RF subsystem
can supply the antenna.
|
| p2mpRfTemperature |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.10 |
|
This object represents the current temperature of the RF unit
|
| p2mpRfTxOscState |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.11 |
|
This object represents the state of the transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
|
| p2mpRfRxOscState |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.12 |
|
This object represents the state of the receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
|
| p2mpRfSupplyVoltageState |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.13 |
|
This object specifies whether the voltage supply to the RF
unit is within specifications or not. Voltage specifications
are hardware dependent.
|
| p2mpRfStatus |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.14 |
|
This object specifies whether the RF resource is functioning
properly. If it is functioning properly then it will be
online(1), else offline(2).
At the Subscriber Unit, this object will reflect offline(2)
if p2mpTxMuteEnable in the p2mpSuRadioPhyTable is true(1).
|
| p2mpRfLoopbackSupported |
.1.3.6.1.4.1.9.9.170.1.1.2.1.1.15 |
|
This object indicates if the RF unit supports loopback.
When true(1), the user can configure loopback using the
objects in p2mpLoopbackTable. When false(2), any attempt
to configure RF loopback will fail.
|
| p2mpDuplexerIndex |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.1 |
|
This object, along with ifIndex, uniquely identifies
an entry in this table. Each entry contains
information about the duplexer's capabilities and also
identifies the associated RF resource.
|
| p2mpDuplexerRF |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.2 |
|
This object identifies the RF resource associated with this
duplexer.
|
| p2mpDuplexerLoPassbandMinFreq |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.3 |
|
This object identifies the minimum frequency in the low
passband that this duplexer will pass through without
attenuation.
|
| p2mpDuplexerLoPassbandMaxFreq |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.4 |
|
This object identifies the maximum frequency in the low
passband that this duplexer will pass through without
attenuation.
|
| p2mpDuplexerHiPassbandMinFreq |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.5 |
|
This object identifies the minimum frequency in the high
passband that this duplexer will pass through without
attenuation.
|
| p2mpDuplexerHiPassbandMaxFreq |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.6 |
|
This object identifies the maximum frequency in the high
passband that this duplexer will pass through without
attenuation.
|
| p2mpDuplexerReceivePassband |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.7 |
|
This object indicates which of the two passbands are being used
to receive transmissions. The RF Resource can receive on
either of the duplexer passbands.
loPassband(1) - The RF Resource is receiving on a frequency
in the low passband.
hiPassband(2) - The RF Resource is receiving on a frequency
in the high passband.
|
| p2mpDuplexerTxInsertionLoss |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.8 |
|
This object represents the loss in 'dB' that would result in
the transmission path due to the duplexer.
|
| p2mpDuplexerBurnDate |
.1.3.6.1.4.1.9.9.170.1.1.2.2.1.9 |
|
This object indicates the date when the revision information
was programmed into non-volatile memory.
|
| p2mpAntennaIndex |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.1 |
|
This object, along with ifIndex, represents the index of this
entry in the p2mpAntennaTable.
|
| p2mpRfResource |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.2 |
|
This object identifies if the antenna is connected to the main
or the diversity RF resource.
|
| p2mpAntennaXDim |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.3 |
|
This object represents the dimension of the antenna in the
X direction.
|
| p2mpAntennaYDim |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.4 |
|
This object represents the dimension of the antenna in the
Y direction.
|
| p2mpAntennaType |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.5 |
|
This object represents the antenna type. For example,
'dish-antenna'.
|
| p2mpAntennaDescr |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.6 |
|
This object is used to describe the antenna. For example,
it could be used to identify the manufacturer like in
'Manufactured by Watkins Johnson'.
|
| p2mpAntennaGain |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.7 |
|
This object represents the receive and transmit gain
of this antenna.
|
| p2mpAntennaPolarization |
.1.3.6.1.4.1.9.9.170.1.1.2.3.1.8 |
|
This object represents the polarization of the antanna.
|
| p2mpLocalLoopbackMode |
.1.3.6.1.4.1.9.9.170.1.1.3.1.1.1 |
|
This object is used to configure the system in loopback mode
prior to executing some system diagnostic tests. The user
selects the point in the system where the data signal should be
looped back. The diagnostic tests outlined in the user manual
have to be manually executed to determine success or failure.
Once all the tests are completed, normal operation is restored
by setting this object to noLoopback(1).
noLoopback(1) - no loopback
fir(2) - loopback at the Finite Impulse
Response (FIR) module.
if(3) - loopback at the IF module. This
exercises the FIR, and IF modules.
rf(4) - loopback at the RF unit. This
exercises the FIR, IF, and RF modules.
This mode is supported only when
p2mpRfLoopbackSupported is true(1).
|
| p2mpLocalLoopbackAntenna |
.1.3.6.1.4.1.9.9.170.1.1.3.1.1.2 |
|
This object identifies the RF resource used for
loopback testing. This object is not applicable for
loopback testing when p2mpLocalLoopbackMode has a
value of 'noLoopback(1)'.
|
| p2mpLocalLoopbackChannel |
.1.3.6.1.4.1.9.9.170.1.1.3.1.1.3 |
|
This object identifies the channel being used to
loopback the data. This object is not applicable
for loopback testing when p2mpLocalLoopbackMode has
a value of 'noLoopback(1)'.
|
| p2mpLedIndex |
.1.3.6.1.4.1.9.9.170.1.1.4.1.1.1 |
|
For a given entPhysicalIndex, this index value uniquely
identifies an entry in the p2mpLedTable.
|
| p2mpLedType |
.1.3.6.1.4.1.9.9.170.1.1.4.1.1.2 |
|
Indicates the type or label of the LED.
|
| p2mpLedState |
.1.3.6.1.4.1.9.9.170.1.1.4.1.1.3 |
|
Indicates the state of the LED.
|
| p2mpSuTxMuteEnable |
.1.3.6.1.4.1.9.9.170.1.2.1.1.1 |
|
When true(1), this object indicates the subscriber unit
transmission has been turned off for a duration indicated by
p2mpSuTxMuteDuration. When false(2), this object indicates
that the subscriber unit is transmitting.
|
| p2mpSuTxMuteDuration |
.1.3.6.1.4.1.9.9.170.1.2.1.1.2 |
|
This object indicates the duration of time (in minutes)
for which the subscriber transmission will be turned off.
|
| p2mpSuPowerScanIndex |
.1.3.6.1.4.1.9.9.170.1.2.2.1.1 |
|
For a given ifIndex, this index value uniquely
identifies an entry in the p2mpSuPowerScanTable.
|
| p2mpSuCenterFrequency |
.1.3.6.1.4.1.9.9.170.1.2.2.1.2 |
|
This object indicates the frequency at which the receive power
at the subscriber unit was measured.
|
| p2mpSuMeasuredPower |
.1.3.6.1.4.1.9.9.170.1.2.2.1.3 |
|
This object represents the power measured at the frequency
indicated by p2mpSuCenterFrequency.
|
| p2mpHeAlcEnable |
.1.3.6.1.4.1.9.9.170.1.3.1.1.1 |
|
This object is used to enable/disable ALC at the Head End. A
value of true(1), indicates that ALC is enabled.
|
| p2mpHeAlcInterval |
.1.3.6.1.4.1.9.9.170.1.3.1.1.2 |
|
This object represents the scheduling interval. It is the
regular interval at which the ALC grant in Map is transmitted
to the SU's
|
| p2mpHeAlcNumMiniSlots |
.1.3.6.1.4.1.9.9.170.1.3.1.1.3 |
|
This indicates the number of minislots within each grant.
|
| p2mpHeIfTxOscState |
.1.3.6.1.4.1.9.9.170.1.3.2.1.1 |
|
This object indicates the state of the IF transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
|
| p2mpHeIfRxOscState |
.1.3.6.1.4.1.9.9.170.1.3.2.1.2 |
|
This object indicates the state of the IF receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
|
| p2mpHeIfRefOscState |
.1.3.6.1.4.1.9.9.170.1.3.2.1.3 |
|
This object indicates the state of the IF reference oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
|
| p2mpHeIfInpFreq |
.1.3.6.1.4.1.9.9.170.1.3.2.1.4 |
|
This object represents the IF input frequency.
|
| p2mpHeIfOutFreq |
.1.3.6.1.4.1.9.9.170.1.3.2.1.5 |
|
This object represents the IF output frequency.
|
| p2mpHeTrapEnable |
.1.3.6.1.4.1.9.9.170.1.3.2.1.6 |
|
When set to true(1), this enables the notifications
that are specific to the head end. When set to false(2),
these notifications are disabled.
|
