| nwDecIVMibRevText |
.1.3.6.1.4.1.52.4.2.2.2.3.3.1.1 |
|
Indicates the current revision level of the DECnet Phase
IV MIB in textual format.
|
| nwDecIVSysRouterId |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.1 |
|
The DECnet Address used to uniquely identify the host (device)
running DECnet Phase IV Routing Services. Since DECnet Phase IV
uses a single address to identify the host and all of its router
ports, rather than using an address per router port,
nwDecIVSysRouterID is the DECnet node address for all the router
ports on the device.
|
| nwDecIVNodeType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.2 |
|
Specifies the node type. Setting this value to 2, (routing-iv),
establishes the Routing Services-enabled device as a DECnet
Level 1, intra-area router. Setting this value to 2, establishes
the Routing Services-enabled device as a DECnet Phase IV Level 2,
or inter-area router.
|
| nwDecIVMaxNodes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.3 |
|
Specifies the maximum number of DECnet nodes allowed within an
area.
|
| nwDecIVMaxBRA |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.4 |
|
Specifies the maximum number of router adjacencies supported by
this node.
|
| nwDecIVMaxBEA |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.5 |
|
Specifies the maximum number of endnode adjacencies supported
by this node.
|
| nwDecIVMaxHops |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.6 |
|
Specifies the maximum number of hops allowed for a valid route
within the area. Any intra-area route consisting of a greater
number of hops than specified by nwDecIVMaxHops is considered
unreachable.
|
| nwDecIVMaxCost |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.7 |
|
Specifies the maximum cost allowed for a valid route within the
area. Any intra-area route with a cost greater than nwDecIVMaxCost
is considered unreachable.
|
| nwDecIVMaxVisits |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.8 |
|
Specifies the maximum number of intra-area hops a packet can be
forwarded. A packet is dropped once it has been forwarded
nwDecIVMaxVisits.
|
| nwDecIVNonBroadcastTimer |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.9 |
|
Specifies the periodic interval (in seconds) at which DECnet
Routing Services advertises its route table, on any non-broadcast
networks attached to any router port configured and enabled for
DECnet Phase IV Routing Services.
|
| nwDecIVBroadcastTimer |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.10 |
|
Specifies the periodic interval (in seconds) at which DECnet
Routing Services advertises its route table on any multi-access
broadcast networks attached to any router port configured and
enabled for DECnet Phase IV Routing Services.
|
| nwDecIVAreas |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.11 |
|
Specifies the maximum number of areas allowed within a Level 2
(inter-area)routing domain.
|
| nwDecIVMaxAreaHops |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.12 |
|
Specifies the maximum number of areas that can be hopped by
a valid inter-area route. Any inter-area route requiring a
greater number of areas to be hopped than specified by
nwDecIVMaxAreaHops is considered invalid.
|
| nwDecIVMaxAreaCost |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.13 |
|
Specifies the maximum cost allowed for a valid Level 2
(inter-area) route. Any inter-area route with a cost greater than
nwDecIVMaxAreaCost is considered unreachable.
|
| nwDecIVSysAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.1 |
|
Sets the administrative state of DECnet Phase IV Routing Services,
system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing
Services to become active on all router ports configured and enabled
for DECnet Phase IV Routing Services. Disabled (2) causes DECnet
Phase IV Routing Services to become inactive system-wide.
|
| nwDecIVSysOperStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.2 |
|
Indicates the current operating condition of DECnet Phase IV
Routing Services system-wide. The value of nwDecIVSysOperStatus
indicates any problem with your DECnet Phase IV Routing Services
configuration. A value of 6 indicates that regardless of the value
of nwDecIVSysAdminStatus, DECnet Phase IV Routing Services is not
operating because of an invalid configuration.
|
| nwDecIVSysAdminReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.3 |
|
Resets DECnet Phase IV Routing Services, system-wide. Reset (2)
forces a restart of DECnet Phase IV Routing Services without a
graceful shutdown on any active router ports and without affecting
any other routing services.
|
| nwDecIVSysOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.4 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVSysOperStatus has been in it's current state.
|
| nwDecIVSysVersion |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.5 |
|
Indicates the current revision level of the DECnet Phase IV Routing
Services firmware, in textual format.
|
| nwDecIVFwdCtrAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.1 |
|
Sets the administrative state of the aggregate (system-wide)
DECnet packet and byte counters. Enabled (3) causes these counters
to become active. Disabled (2) causes these counters to become
inactive.
|
| nwDecIVFwdCtrReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.2 |
|
Resets the aggregate (system-wide) DECnet packet and byte counters.
Reset (2) resets the DECnet aggregate counters to 0.
nwDecIVFwdCtrOperationalTime is also reset to 0.
|
| nwDecIVFwdCtrOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.3 |
|
Indicates the elapsed time, in hundredths of a second, that
DecIVFwdCtrOperStatus has been in the current state.
|
| nwDecIVFwdCtrInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.4 |
|
Indicates the total number of DECnet packets that have been
received, system-wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.5 |
|
Indicates the total number of DECnet packets that have been
transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrFwdPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.6 |
|
Indicates the total number of DECnet packets that have been
forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrFilteredPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.7 |
|
Indicates the total number of DECnet packets that have been
administratively filtered, system-wide, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.8 |
|
Indicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrAddrErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.9 |
|
Indicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because of addressing errors in the DECnet header.
|
| nwDecIVFwdCtrLenErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.10 |
|
Indicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because an invalid packet length is contained in the DECnet header.
|
| nwDecIVFwdCtrHdrErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.11 |
|
Indicates the total number of DECnet packets that have been
discarded, system-wide, during nwDecIVFwdCtrOperationalTime,
because of an invalid DECnet header.
|
| nwDecIVFwdCtrInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.12 |
|
Indicates the total number of bytes in the DECnet packets that
have been received, system-wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.13 |
|
Indicates the total number of bytes in the DECnet packets that
have been transmitted, system-wide, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrFwdBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.14 |
|
Indicates the total number of bytes in the DECnet packets
that have been forwarded, system-wide, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrFilteredBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.15 |
|
Indicates the total number of bytes in the DECnet packets that
have been administratively filtered, system-wide, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.16 |
|
Indicates the total number of bytes in the DECnet packets that
have been discarded, system wide, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrHostInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.17 |
|
Indicates the total number of DECnet packets that have been
successfully delivered to the local host, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrHostOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.18 |
|
Indicates the total number of DECnet packets that have been
transmitted by the local host, during nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrHostDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.19 |
|
Indicates the total number of DECnet packets that have been
discarded by the local host, during nwDecIVFwdCtrOperationalTime,
due to a lack of host resources.
|
| nwDecIVFwdCtrHostInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.20 |
|
Indicates the total number of bytes in the DECnet packets that
have been received by the local host, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrHostOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.21 |
|
Indicates the total number of bytes in the DECnet packets that
have been transmitted by the local host, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdCtrHostDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.22 |
|
Indicates the total number of bytes in the DECnet packets that have
been discarded by the local host, during
nwDecIVFwdCtrOperationalTime, due to a lack of host resources.
|
| nwDecIVFwdIfEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1 |
|
Each entry specifies the DECnet Phase IV Routing Services
configuration for the router port for which the entry exists.
|
| nwDecIVFwdIfCtrEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1 |
|
Each entry indicates the current packet and byte count of DECnet
packets on each router port for which the entry exists.
|
| nwDecIVProtoAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.1 |
|
Sets the administrative state of the DECnet Phase IV
distance-vector-based routing protocol system-wide. Enabled (3)
causes the routing protocol to become active on all router ports
configured and enabled for DECnet Routing Services. Disabled (2)
causes the routing protocol to become inactive.
|
| nwDecIVProtoOperStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.2 |
|
Indicates the current operating condition of the DECnet Phase
IV distance-vector-based routing protocol system-wide. The value
of nwDecIVProtoOperStatus indicates any problem with the DECnet
Phase IV distance-vector-based routing protocol configuration.
A value of 6 indicates that regardless of the value of
nwDecIVProtoAdminStatus, the DECnet Phase IV distance-vector-based
routing protocol is not operating because of an invalid configuration.
|
| nwDecIVProtoAdminReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.3 |
|
Resets the DECnet Phase IV distance-vector-based routing
protocol. Reset (2) forces a system-wide restart of the protocol
without a graceful shut-down on any active router ports.
|
| nwDecIVProtoOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.4 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVProtoOperStatus has been in current state.
|
| nwDecIVProtoVersion |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.5 |
|
Indicates the current revision level of the DECnet Phase IV
distance-vector-based routing protocol firmware, in textual format.
|
| nwDecIVProtoStackSize |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.6 |
|
Specifies the stack size of the DECnet Phase IV distance-vector-
based routing protocol thread. In order for a change of this value
to take effect, the protocol (nwDecIVProtoAdminReset), DECnet
Phase IV Routing Services (nwDecIVSysAdminReset), or the device
running Routing Services must be reset.
|
| nwDecIVProtoThreadPriority |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.7 |
|
Specifies the run-time execution priority of the DECnet Phase IV
distance-vector-based routing protocol thread. In order for a change
of this value to take effect, the protocol (nwDecIVProtoAdminReset),
DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the
device running Routing Services must be reset.
|
| nwDecIVProtoDatabaseThreshold |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.8 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVProtoAgeOut |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.9 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVProtoHoldDown |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.10 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVProtoCtrAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.1 |
|
Sets the administrative state of the aggregate (system-wide) DECnet
Phase IV distance-vector-based routing protocol packet and byte
counters. Enabled (3) causes these counters to become active.
Disabled (2) causes these counters to become inactive.
|
| nwDecIVProtoCtrReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.2 |
|
Resets the aggregate (system-wide) DECnet Phase IV
distance-vector-based routing protocol packet and byte counters.
Reset (2) resets the DECnet aggregate counters to 0.
nwDecIVProtoCtrOperationalTime is also reset to 0.
|
| nwDecIVProtoCtrOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.3 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVProtoCtrAdminStatus has been in it's current state.
|
| nwDecIVProtoCtrInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.4 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been received, system-wide,
during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.5 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been transmitted, system-wide,
during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrFilteredPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.6 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been administratively filtered,
system-wide, during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.7 |
|
Indicates the total number of the DECnet Phase IV distance-vector
-based routing protocol packets that have been discarded,
system-wide, during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.8 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vector based routing protocol packets that have been
received, system-wide, during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.9 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrFilteredBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.10 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
administratively filtered, system-wide, during
nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoCtrDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.11 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vectorbased routing protocol packets that have been
discarded system-wide, during nwDecIVProtoCtrOperationalTime.
|
| nwDecIVProtoIfEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1 |
|
Each entry contains the DECnet Phase IV distance-vector-based
routing protocol configuration for the router port for which the
entry exists.
|
| nwDecIVProtoIfCtrEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1 |
|
Each entry indicates the current packet and byte count of DECnet
Phase IV distance-vector-based routing protocol packets on the router
port for which the entry exists.
|
| nwDecIVFibEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1 |
|
Each entry in the table describes a route to a particular DECnet
destination network and node.
|
| nwDecIVAclValidEntries |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.1 |
|
Indicates the number of valid entries that exist in the access
control list table, nwDecIVAclTable.
|
| nwDecIVAclEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1 |
|
Each entry contains DECnet source/destination access information.
|
| nwDecIVHostMapEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1 |
|
Each entry contains one DecIVAddress to circuit
equivalence. Also provided is the framing required to
converse with this host, and the corresponding logical
port number.
|
| nwDecIVEventAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.1 |
|
Sets the administrative state of DECnet event logging. Enabled (3)
causes the event log to become active. Disabled (2) causes the event
log to become inactive.
|
| nwDecIVEventMaxEntries |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.2 |
|
Sets the maximum number of entries allowed in the event log table.
When the number of entries reaches the value of nwDecIVEventMaxEntries,
the first (oldest) entry is deleted to allow a new entry to be added.
|
| nwDecIVEventTraceAll |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.3 |
|
Enabled (3) allows logging of all event types on all router ports
for all protocols and components. Disabled (2) causes the filter
table to specify which events to log.
|
| nwDecIVEventFilterEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1 |
|
Each entry describes an event filter which defines a particular type
of event to be logged to the event log. The value of
nwDecIVEventFltrProtocol indicates the value used either in the
nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing
Services MIB, which identifies the protocol or component to which the
entry applies.
|
| nwDecIVEventEntry |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1 |
|
Each entry contains the information about an event that has
been logged to the event table.
|
| nwDecIVFwdIfIndex |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.1 |
|
Indicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.
|
| nwDecIVFwdIfAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.2 |
|
Sets the administrative state of DECnet Phase IV Routing Services
on the router port for which the entry exists. Enabled (3) causes
DECnet Phase IV Routing Services to become active. Disabled (2)
causes it to become inactive.
|
| nwDecIVFwdIfOperStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.3 |
|
Indicates the current operating condition of DECnet Phase IV
Routing Services on the router port for which the entry exists.
The value of nwDecIVFwdIfOperStatus indicates any problem with the
configuration of DECnet Phase IV Routing Services on the router port.
value of 6 indicates that regardless of the value of
nwDecIVFwdIfAdminStatus, DECnet Phase IV Routing Services is not
operating because of an invalid port-level configuration.
|
| nwDecIVFwdIfOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.4 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVFwdIfOperStatus has been in its current state.
|
| nwDecIVFwdIfControl |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.5 |
|
This object does not apply to this protocol. It is a common object,
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVFwdIfMtu |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.6 |
|
Specifies the Maximum Transmission Unit (MTU) for DECnet packets on
the router port for which the entry exists. This includes the DECnet
header and data, but does not include framing.
|
| nwDecIVFwdIfForwarding |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.7 |
|
Controls the forwarding of DECnet packets on the router port for
which the entry exists. Enabled (3) causes DECnet packets to be
forwarded. Disabled (2) prevents DECnet packets from being forwarded.
|
| nwDecIVFwdIfFrameType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.8 |
|
Specifies the framing type for DECnet packets forwarded on the router
port for which the entry exists. Some frame types are only valid for
specific media types. The comments reflect those valid media types.
|
| nwDecIVFwdIfAclIdentifier |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.9 |
|
Specifies the Access Control ID of the access control list in
effect for DECnet packets being routed on the router port for which
the entry exists. A value of 0 indicates that no access control list
is in effect.
|
| nwDecIVFwdIfAclStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.10 |
|
Controls the operation of any access control list configured
for DECnet traffic on the router port for which the entry exists.
Enabled (3) applies the access control list indicated by the value
of nwDecIVFwdIfAclIdentifier to all DECnet traffic being routed on
the port. Disabled (2) prevents the access control list from being
applied.
|
| nwDecIVFwdIfCacheControl |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.11 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVFwdIfCacheEntries |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.12 |
|
This object does not apply to this protocol. It is a common
object inherited from the MIB framework used to provide a
common management interface to all the Cabletron Routing
Services protocol-specific MIBs. Setting this object has no
effect.
|
| nwDecIVFwdIfCacheHits |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.13 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.
|
| nwDecIVFwdIfCacheMisses |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.14 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific
MIBs. Setting this object has no effect.
|
| nwDecIVFwdIfCtrIfIndex |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.1 |
|
Indicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.
|
| nwDecIVFwdIfCtrAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.2 |
|
Sets the administrative state of the per-port DECnet packet and
byte counters on the router port for which the entry exists. Enabled
(3) causes these counters to become active. Disabled (2) causes
these counters to become inactive.
|
| nwDecIVFwdIfCtrReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.3 |
|
Resets the per-port DECnet packet and byte counters on the router
port for which the entry exists. Reset (2) resets the counters to 0.
nwDecIVFwdIfCtrOperationalTime is also reset to 0.
|
| nwDecIVFwdIfCtrOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.4 |
|
Indicates the elapsed time, in hundredths of a second, that the
per-port DECnet packet and byte counters have been active on the
router port for which the entry exists.
|
| nwDecIVFwdIfCtrInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.5 |
|
Indicates the total number of DECnet packets that have been
received, during nwDecIVFwdIfCtrOperationaltime, on the router port
for which the entry exists.
|
| nwDecIVFwdIfCtrOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.6 |
|
Indicates the total number of DECnet packets that have been
transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.
|
| nwDecIVFwdIfCtrFwdPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.7 |
|
Indicates the total number of DECnet packets that have been
forwarded on the router port for which the entry exists, during
nwDecIVFwdCtrOperationalTime.
|
| nwDecIVFwdIfCtrFilteredPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.8 |
|
Indicates the total number of DECnet packets that have been
administratively filtered, during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.
|
| nwDecIVFwdIfCtrDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.9 |
|
Indicates the total number of DECnet packets that have been
discarded (dropped), during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.
|
| nwDecIVFwdIfCtrAddrErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.10 |
|
Indicates the total number of DECnet packets that have been
discarded because of addressing errors in the DECnet header,
during nwDecIVFwdIfCtrOperationalTime, on the router port for
which the entry exists.
|
| nwDecIVFwdIfCtrLenErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.11 |
|
Indicates the total number of DECnet packets that have been
discarded because an invalid packet length was contained in the
DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.
|
| nwDecIVFwdIfCtrHdrErrPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.12 |
|
Indicates the total number of DECnet packets that have been
discarded because of an invalid DECnet header, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.
|
| nwDecIVFwdIfCtrInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.13 |
|
Indicates the total number of bytes in the DECnet packets that
have been received, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.
|
| nwDecIVFwdIfCtrOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.14 |
|
Indicates the total number of bytes in the DECnet packets that have
been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router
port for which the entry exists.
|
| nwDecIVFwdIfCtrFwdBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.15 |
|
Indicates the total number of bytes in the DECnet packets that
have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.
|
| nwDecIVFwdIfCtrFilteredBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.16 |
|
Indicates the total number of bytes in the DECnet packets that
have been administratively filtered, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.
|
| nwDecIVFwdIfCtrDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.17 |
|
Indicates the total number of bytes in the DECnet packets that
have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the
router port for which the entry exists.
|
| nwDecIVFwdIfCtrHostInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.18 |
|
Indicates the total number of DECnet packets that have been
delivered to the local host, during nwDecIVFwdIfCtrOperationalTime,
that were received on the router port for which the entry exists.
|
| nwDecIVFwdIfCtrHostOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.19 |
|
Indicates the total number of DECnet packets that have been
transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime,
on the router port for which the entry exists.
|
| nwDecIVFwdIfCtrHostDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.20 |
|
Indicates the total number of DECnet packets that have been
discarded by the local host, during nwDecIVFwdIfCtrOperationalTime,
that were received on the router port for which the entry exists.
|
| nwDecIVFwdIfCtrHostInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.21 |
|
Indicates the total number of bytes in the DECnet packets that
have been delivered to the local host, during
nwDecIVFwdIfCtrOperationalTime, that were received on the router port
for which the entry exists.
|
| nwDecIVFwdIfCtrHostOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.22 |
|
Indicates the total number of bytes in the DECnet packets that
have been transmitted by the local host, during
nwDecIVFwdIfCtrOperationalTime, on the router port for which the
entry exists.
|
| nwDecIVFwdIfCtrHostDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.23 |
|
Indicates the total number of bytes in the DECnet packets that
have been discarded by the local host, due to a lack of host
resources, that were received on the router port for which the entry
exists, during nwDecIVFwdIfCtrOperationalTime.
|
| nwDecIVProtoIfIndex |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.1 |
|
Indicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.
|
| nwDecIVProtoIfAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.2 |
|
Sets the administrative state of the DECnet Phase IV
distance-vector-based routing protocol on the router port for which
the entry exists. Enabled (3) causes the routing protocol to become
active on the router port. Disabled (2) causes it to become inactive.
|
| nwDecIVProtoIfOperStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.3 |
|
Indicates the current operating condition of the DECnet Phase IV
distance-vector-based routing protocol on the router port for which
the entry exists. The value of nwDecIVProtoIfOperStatus indicates
any problem with your routing protocol configuration on the router
port. A value of 6 indicates that regardless of the value of
nwDecIVProtoIfAdminStatus, the routing protocol is not operating
because of an invalid configuration.
|
| nwDecIVProtoIfOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.4 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVProtoIfOperStatus has been in it`s current state.
|
| nwDecIVProtoIfVersion |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.5 |
|
Indicates the revision level of the DECnet Phase IV
distance-vector-based routing protocol firmware on the router port
for which the entry exists, in textual format.
|
| nwDecIVProtoIfAdvertisement |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.6 |
|
Sets the interval, in seconds, at which the DECnet Phase IV
distance-vectorbased routing protocol advertises its route table on
the router port for which the entry exists. Change this value to
cause the DECnet Phase IV distance-vector-based routing protocol to
advertise its route table more or less frequently on the router port.
|
| nwDecIVProtoIfFloodDelay |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.7 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.
|
| nwDecIVProtoIfRequestDelay |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.8 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.
|
| nwDecIVProtoIfPriority |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.9 |
|
Sets the priority of the DECnet Phase IV distance-vector-based
routing protocol on the router port for which the entry exists.
Within an area, the router with the highest value for
nwDecIVProtoIfPriority becomes the priority or designated router.
The highest possible value for nwDecIVProtocolIfPriority is 127. Set
this value high to cause your DECnet Phase IV Routing Services-enabled
device to become the designated router. Set this value low to guarantee
that it does not become the designated router.
|
| nwDecIVProtoIfHelloTimer |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.10 |
|
Sets the interval, in seconds, at which DECnet Phase IV
distance-vector-based routing protocol sends Hello packets on the
router port for which the entry exists.
|
| nwDecIVProtoIfSplitHorizon |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.11 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.
|
| nwDecIVProtoIfPoisonReverse |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.12 |
|
This object does not apply to this protocol. It is a common object
inherited from the MIB framework used to provide a common management
interface to all the Cabletron Routing Services protocol-specific MIBs.
Setting this object has no effect.
|
| nwDecIVProtoIfSnooping |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.13 |
|
Controls the operation of DECnet Phase IV distance-vector-based
routing protocol snooping on the router port. When snooping is
enabled the DECnet Phase IV distance-vector-based routing protocol
operates in passive mode, so that it receives route information,
builds and maintains a route table, but does not advertise the route
table or send updates on the router port for which the entry exists.
|
| nwDecIVProtoIfType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.14 |
|
Indicates whether the directly connected network segment does or
does not support broadcast media access.
|
| nwDecIVProtoIfXmitCost |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.15 |
|
Sets the cost of transmitting a packet on the network segment
connected to the router port for which the entry exists. The DECnet
Phase IV distance-vector-based routing protocol picks the route with
the least total nwDecIVProtoIfXmitCost as the best route. If
nwDecIVProtocolIfXmitCost, also known as path cost, is the same for
all possible routes , the best route chosen is the route with the
least number of hops is chosen as the best route.
|
| nwDecIVProtoIfAclIdentifier |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.16 |
|
Specifies the Access Control ID of the access control list in
effect for DECnet Phase IV distance-vector-based routing protocol
packets on the router port for which the entry exists. A value of 0
indicates that there is no access control list in effect for DECnet
Phase IV distance-vector-based routing protocol packets on the router
port.
|
| nwDecIVProtoIfAclStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.17 |
|
Controls the operation of the access control list identified by
nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control
list to all DECnet Phase IV distance-vector-based routing protocol
packet traffic on the router port for which the entry exists. Disabled
(2) prevents the access control list from being applied.
|
| nwDecIVProtoIfCtrIfIndex |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.1 |
|
Indicates the value of MIB 2 ifindex, which identifies the router
port for which the entry exists.
|
| nwDecIVProtoIfCtrAdminStatus |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.2 |
|
Sets the administrative state of the per-port DECnet Phase IV
distance-vectorbased routing protocol packet and byte counters on
the router port for which the entry exists. Enabled (3) causes these
counters to become active. Disabled (2) causes these counters to
become inactive.
|
| nwDecIVProtoIfCtrReset |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.3 |
|
Resets the per-port DECnet Phase IV distance-vector-based routing
protocol packet and byte counters on the router port for which the
entry exists. Reset (2) resets the counters to 0.
nwDecIVProtoIfCtrOperationalTime is also reset to 0.
|
| nwDecIVProtoIfCtrOperationalTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.4 |
|
Indicates the elapsed time, in hundredths of a second, that
nwDecIVProtoIfCtrAdminStatus has been in the current state.
|
| nwDecIVProtoIfCtrInPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.5 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been received, during
nwDecIVProtoIfCtrOperationalTime, on the router port for which the
entry exists.
|
| nwDecIVProtoIfCtrOutPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.6 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been transmitted, during
nwDecIVProtoIfCtrOperationalTime, on the router port for which the
entry exists.
|
| nwDecIVProtoIfCtrFilteredPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.7 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been administratively filtered,
during nwDecIVProtoIfCtrOperationalTime, on the router port for which
the entry exists.
|
| nwDecIVProtoIfCtrDiscardPkts |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.8 |
|
Indicates the total number of DECnet Phase IV distance-vector-based
routing protocol packets that have been discarded, during
nwDecIVProtoIfCtrOperationalTime, that were received on the router
port for which the entry exist.
|
| nwDecIVProtoIfCtrInBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.9 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
received, during nwDecIVProtoIfCtrOperationalTime, on the router
port for which the entry exists.
|
| nwDecIVProtoIfCtrOutBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.10 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router
port for which the entry exists.
|
| nwDecIVProtoIfCtrFilteredBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.11 |
|
Indicates the total number of bytes in the DECnet Phase IV
distance-vector-based routing protocol packets that have been
administratively filtered, during nwDecIVProtoIfCtrOperationalTime,
that were received on the router port for which the entry exists.
|
| nwDecIVProtoIfCtrDiscardBytes |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.12 |
|
Indicates the total number of bytes in the DECnet packets that have
been discarded, during nwDecIVProtoIfCtrOperationalTime, that were
received on the router port for which the entry exists.
|
| nwDecIVFibNodeId |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.1 |
|
Contains the DECnet Address of the destination node of the route
for which the entry exists.
|
| nwDecIVFibNextHopNodeId |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.2 |
|
Contains the DECnet Address of the next hop router for the route
for which the entry exists.
|
| nwDecIVFibNextHopIf |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.3 |
|
Indicates the value of MIB 2 ifindex, which identifies the router
port through which the route exists.
|
| nwDecIVFibRouteType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.4 |
|
Indicates the status of the route. A value of 3 indicates that the
destination is on the network segment that is directly connected to
the router port identified by nwDecIVFibNextHopIf. A value of 4
indicates that the destination is on an indirectly connected network
segment, which is reachable through the next hop router indicated by
the value of nwDecIVFibNextHopNodeId. A value of 2 indicates that the
route is invalid.
|
| nwDecIVAclIdentifier |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.1 |
|
This is the primary (major) index into the DECnet access control
list table. This value identifies each access control list by a
unique identifier, a number arbitrarily assigned by the user. All
entries that have the same value for nwDecIVAclIdentifier belong to
the same access control list.
|
| nwDecIVAclSequence |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.2 |
|
This is the secondary (minor) index into the DECnet access control
list table. This number corresponds to a sequence number used to
order multiple entries within the same access control list.
|
| nwDecIVAclPermission |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.3 |
|
Specifies whether access is allowed or denied between the source
and destination address pair. Note that source and destination are
interchangeable when bi-directional control is selected. To remove
an existing entry set nwDecIVAclPermission to invalid (2). Invalid
entries disappear after reboot.
|
| nwDecIVAclMatches |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.4 |
|
Indicates the number of matches on this entry that have resulted
in the permit/deny access restriction being applied as part of the
forwarding process.
|
| nwDecIVAclDestAddress |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.5 |
|
Specifies the destination DECnet Address used to compare for
matches on the access control list. Either the Area ID or Node ID
of this address may be set to 0, a wildcard value which matches all
areas or all nodes.
|
| nwDecIVAclSrcAddress |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.6 |
|
Specifies the source DECnet Address used to compare for matches on
the access control list. Either the Area ID or Node ID of this
address may be set to a wildcard value which matches all areas or
all nodes.
|
| nwDecIVHostMapIfIndex |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.1 |
|
This is the primary (major) index into the DecIV HostMap
table. This number corresponds to the index into the MIB-2
Interfaces Group which describes the DecIV router port for which
the entry exists.
|
| nwDecIVHostMapDecIVAddr |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.2 |
|
The DecIVAddress of the host on the corresponding interface
and circuit (if applicable).
|
| nwDecIVHostMapType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.3 |
|
Setting this object to the value invalid(2) has
the effect of invalidating the corresponding entry in the
nwDecIVHostMapTable. That is, it effectively dissasociates
the circuitand/or interface identified with said entry from the
mapping identified with said entry. It is an implementation-
specific matter as to whether the agent removes an invalidated
entry from the table. Accordingly, management stations must be
prepared to receive tabular information from agents that
corresponds to entries not currently in use. Proper inter-
pretation of such entries requires examination of the relevant
wDecIVHostMapType object.
|
| nwDecIVHostMapCircuitID |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.4 |
|
The identifier for the virtual circuit present on the
interface. On an interface configured for Frame Relay,
this number is the DLCI for the DecIV Address at the end of
the circuit. For non-WAN interfaces, the value of this
object is zero.
|
| nwDecIVHostMapFraming |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.5 |
|
Specifies the framing type required to converse with the
host for which this entry exists.
|
| nwDecIVHostMapPortNumber |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.6 |
|
The unique value for the logical port number. It's value
ranges between 1 and a maximum value which is dependent on both
the number of configured interfaces in the system and the number
of circuits present on those interfaces which are of WAN type.
|
| nwDecIVEventFltrProtocol |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.1 |
|
Indicates the value of the Cabletron Routing Services MIB
nwRtgProtocolInstance or nwComponentRtgInstance which identifies the
protocol involved in the event for which the event filter exists.
|
| nwDecIVEventFltrIfNum |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.2 |
|
Specifies the router port involved in the event for which the event
filter exists.
|
| nwDecIVEventFltrControl |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.3 |
|
Set this value to 3 to add the entry to the event filter table. Set
this value to 2 to remove the entry from the event filter table.
|
| nwDecIVEventFltrType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.4 |
|
This 6 bit mask specifies the types of events to be logged. By
default all 6 bits are set to 1, indicating that all types of events
are to be logged. Setting any bit to 0 removes an event type from
this field and prevents that type of event from being logged. Setting
any bit to 1 adds an event type to this field and enables that type
of event to be logged.
|
| nwDecIVEventFltrSeverity |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.5 |
|
Specifies the level of severity an event must meet in order to be
logged. Controls the amount of event logging by ignoring events of a
lower priority than specified by this filter value. `Highmed' ignores
only events of the lowest severity. `Highlow' logs all events highest
priority through lowest. `Highest' severity causes all events except
those of the highest severity to be ignored. `Highmed' severity is the
default setting which causes only events of the lowest severity to be
ignored. `Highlow' severity logs all events, regardless of severity.
|
| nwDecIVEventFltrAction |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.6 |
|
Specifies how the events are to be logged. Logging to the `log'
stores the events in the event log table (nwDecIVEventLogTable).
Logging to'trap' sends events out through the trap mechanism.
|
| nwDecIVEventNumber |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.1 |
|
An ordinal value assigned to the event for which the log entry
exists. nwDecIVEventNumber is assigned so that each event in the
event log can be uniquely identified by the value of
nwDecIVEventNumber.
|
| nwDecIVEventTime |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.2 |
|
Indicates the time at which the event was logged to the event
log.
|
| nwDecIVEventType |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.3 |
|
Indicates the type of event that was logged.
|
| nwDecIVEventSeverity |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.4 |
|
Indicates the severity that was assigned to the event.
|
| nwDecIVEventProtocol |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.5 |
|
Indicates the value of the Cabletron Routing Services MIB
nwRtgProtocolInstance or nwComponentInstance which identifies the
protocol or component that was involved in the event.
|
| nwDecIVEventIfNum |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.6 |
|
Indicates the router port that was involved in the event.
|
| nwDecIVEventTextString |
.1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.7 |
|
Contains the actual text string that was logged.
|
