| switchNumber |
.1.3.6.1.4.1.52.3.9.1.10.7.1.1 |
|
The total number of switches present on this system.
|
| switchInfoEntry |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1 |
|
An entry in the table, containing information
about a single switch in this system.
|
| switchOIDEntry |
.1.3.6.1.4.1.52.3.9.1.10.7.1.3.1 |
|
An entry in the table, containing System Object
Identifier for a single switch in this system.
|
| switchPortMgtEntry |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1 |
|
An entry in the table, containing information about
configuration in one switch port of the switch.
|
| systemSTAStatus |
.1.3.6.1.4.1.52.3.9.1.10.7.3.1 |
|
Global spanning tree status.
(1) Spanning tree protocol is enabled.
(2) Spanning tree protocol is disabled.
|
| tftpDownloadServerIP |
.1.3.6.1.4.1.52.3.9.1.10.7.4.1 |
|
The IP address of a TFTP server from which a
firmware image can be downloaded.
|
| tftpDownloadAgentBoardFwFileName |
.1.3.6.1.4.1.52.3.9.1.10.7.4.2 |
| tftpDownloadAgentBoardFwDownloadNode |
.1.3.6.1.4.1.52.3.9.1.10.7.4.3 |
|
Indicates whether a newly upgraded firmware
version should write to flash. When this object
is temporary(2), following a successful upgrade
the system will switch to run the new firmware but
will not upgrade the new firmware to flash. That
means after a power cycle, system will run the
firmware residing the flash.
When this object is permanent(1), following a
successful firmware upgrade, the flash will be
upgraded and the system will automatically switch
to run the new firmware.
|
| tftpDownloadStatus |
.1.3.6.1.4.1.52.3.9.1.10.7.4.4 |
|
Setting this object to active(1) trigger the TFTP
download action. Setting this object to notActive(2)
has no effect. The system always returns the value
notActive(2) when this object is read.
|
| restartOptionPOST |
.1.3.6.1.4.1.52.3.9.1.10.7.5.1 |
|
Setting this object as enabled. The system will do POST
when it restart
|
| restartOptionReloadFactoryDefault |
.1.3.6.1.4.1.52.3.9.1.10.7.5.2 |
|
Setting this object as enabled. The system will do
factory reset when it restart
|
| restartOptionKeepIpSetting |
.1.3.6.1.4.1.52.3.9.1.10.7.5.3 |
|
Setting this object as enabled. The system will keep IP
setting when it do factory reset.
|
| restartOptionKeepUserAuthentication |
.1.3.6.1.4.1.52.3.9.1.10.7.5.4 |
|
Setting this object as enabled. The system will keep
user authentication setting when it do factory reset.
|
| restartAction |
.1.3.6.1.4.1.52.3.9.1.10.7.5.5 |
|
Setting this object to active(1) trigger the system
restart. Setting this object to notActive(2) has
no effect. The system always returns the value
notActive(2) when this object is read.
|
| portMirrorStatus |
.1.3.6.1.4.1.52.3.9.1.10.7.6.1 |
|
Port mirroring function status.
(1) mirroring function is enabled.
(2) mirroring function is disabled.
|
| portMirrorSnifferPort |
.1.3.6.1.4.1.52.3.9.1.10.7.6.2 |
|
Linear port number of sniffer port to which all
frames to/from mirrored ports are sent. Frames
are only mirrored if the portMirrorStatus object
is set to enabled(1).
|
| portMirrorMirroredPort |
.1.3.6.1.4.1.52.3.9.1.10.7.6.3 |
|
Linear port number of mirrored port. The traffic of
mirrored port will be 'copied' to sniffer port.
|
| igmpStatus |
.1.3.6.1.4.1.52.3.9.1.10.7.7.1 |
|
Parameter to enable or disable IGMP snooping on the device.
When enabled, the device will examine IGMP packets and set
up filters for IGMP ports. The default is enabled.
|
| igmpQueryCount |
.1.3.6.1.4.1.52.3.9.1.10.7.7.2 |
|
Maximum number of queries that have not been heard on the
system before the system starts taking action to solicit
reports(default is 5).
|
| igmpReportDelay |
.1.3.6.1.4.1.52.3.9.1.10.7.7.3 |
|
Timeout value(mins) between IGMP reports received on a port
for an IP Multicast Address that can pass before the system
sends an IGMP Query out the port and removes it from the
list(default is 5 minutes).
|
| swUnitIndex |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.1 |
|
This object identifies the switch within the system
for which this entry contains information. This
value can never be greater than switchNumber.
|
| swMainBoardHwVer |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.2 |
|
Hardware version of the main board.
|
| swMainBoardFwVer |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.3 |
|
Firmware version of the main board.
|
| swAgentBoardHwVer |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.4 |
|
Hardware version of the agent board.
|
| swAgentBoardFwVer |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.5 |
|
Firmware version of the agent board.
|
| swAgentBoardPOSTCodeVer |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.6 |
|
POST code version of the agent board.
|
| swPortNumber |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.7 |
|
The total port number of this switch
(including expansion slot).
|
| swPowerStatus |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.8 |
|
Indicates the switch using internalPower(1),
redundantPower(2) or both(3)
|
| swExpansionSlot1 |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.9 |
|
Type of expansion module in this switch slot 1.
|
| swExpansionSlot2 |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.10 |
|
Type of expansion module in this switch slot 2.
|
| swRoleInSystem |
.1.3.6.1.4.1.52.3.9.1.10.7.1.2.1.11 |
|
Indicates the switch is master(1), backupMaster(2)
or slave(3) in this system.
|
| switchOIDIndex |
.1.3.6.1.4.1.52.3.9.1.10.7.1.3.1.1 |
|
This object identifies the switch within the system
for which this entry contains information. This
value can never be greater than switchNumber.
Index value 1 always represents the Master in a
stacked configuration and the only device in a
standalone configuration.
Subsequent indices are sequential with the lowest
number representing the Slave nearest the Master
and so on.
|
| switchOIDValue |
.1.3.6.1.4.1.52.3.9.1.10.7.1.3.1.2 |
|
This object contains the System Object Identifier
that uniquely identifies the type of switch.
|
| swPortMgtIndex |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.1 |
|
This object identifies the port within the switch
for which this entry contains information.
|
| swPortMgtPortType |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.2 |
|
Indicates the port type is tenBaseT/hundredBaseTX(1),
hundredBaseFX(2) or thousandBaseSX(3).
|
| swPortMgtSpeedDpxAdmin |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.3 |
|
Set the port speed and duplex mode as follows:
halfDuplex10(1) - 10Mbps and half duplex mode
fullDuplex10(2) - 10Mbps and full duplex mode
halfDuplex100(3) - 100Mbps and half duplex mode
fullDuplex100(4) - 100Mbps and full duplex mode
halfDuplex1000(5) - 1000Mbps and half duplex mode
fullDuplex1000(6) - 1000Mbps and full duplex mode
autoNegotiation(7) - let the switch to negotiate with
the other end of connection.
hundredBaseTX port can be set as
halfDuplex10(1)
fullDuplex10(2)
halfDuplex100(3)
fullDuplex100(4)
autoNegotiation(7)
hundredBaseFX port can be set as
halfDuplex100(3)
fullDuplex100(4)
thousandBaseSX port can be set as
halfDuplex1000(5)
fullDuplex1000(6)
autoNegotiation(7)
The actual operating speed and duplex of the port is
given by swPortMgtSpeedDpxInUse.
|
| swPortMgtSpeedDpxInUse |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.4 |
|
The operating speed and duplex mode of the switched port.
|
| swPortMgtFlowCtrlAdmin |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.5 |
|
(1) Flow control mechanism is enabled.
If the port type is hundredBaseTX or thousandBaseSX:
When the port is operating in halfDuplex mode,
the port uses backPressure flow control mechanism.
When the port is operating in fullDuplex mode,
the port uses IEEE 802.3x flow control mechanism.
If the port type is hundredBaseFX:
When the port is operating in halfDuplex mode, the
port uses backPressure flow control mechanism. When
the port is operating in fullDuplex mode, Flow
control mechanism will not function.
(2) Flow control mechanism is disabled.
(3) Flow control mechanism is backPressure.
When the port is in fullDuplex mode
this flow control mechanism will not function.
(4) Flow control mechanism is IEEE 802.3x flow control.
When the port is in halfDuplex mode
this flow control mechanism will not function.
hundredBaseTX and thousandBaseSX port can be set as:
enabled(1),
disabled(2),
backPressure(3),
dot3xFlowControl(4).
hundredBaseFX port can be set as:
enabled(1),
disabled(2),
backPressure(3).
The actual flow control mechanism is used given by
swPortMgtFlowCtrlInUse.
|
| swPortMgtFlowCtrlInUse |
.1.3.6.1.4.1.52.3.9.1.10.7.2.1.1.6 |
|
(1) BackPressure flow control mechanism is used.
(2) IEEE 802.3 flow control mechanism is used.
(3) Flow control mechanism is disabled.
|
