| h245ConfigT101Timer |
.0.0.8.341.1.0.3.1.1.1.1.1 |
|
This timer is used during Capability Exchange procedure. This timer is
used in the AWAITING RESPONSE state. It specifies the maximum time during
which no TerminalCapabilitySetAck or TerminalCapabilitySetReject message
may be received.
|
| h245ConfigT102Timer |
.0.0.8.341.1.0.3.1.1.1.1.2 |
|
This timer is used during Maintenance Loop procedure. This timer is used
during the AWAITING RESPONSE state. It specifies the maximum allowed time
during which no MaintenanceLoopAck or MaintenanceLoopReject message may
be received .
|
| h245ConfigT103Timer |
.0.0.8.341.1.0.3.1.1.1.1.3 |
|
This timer is used during Uni-directional and
Bi-directional Logical Channel Signalling procedure. This timer is used
in the AWAITING ESTABLISHMENT and AWAITING RELEASE states. It specifies
the maximum time during which no OpenLogicalChannelAck or
OpenLogicalChannelReject or CloseLogicalChannelAck message may be
received.
|
| h245ConfigT104Timer |
.0.0.8.341.1.0.3.1.1.1.1.4 |
|
This timer is used during H.223 Multiplex Table procedure. This timer is
used in the AWAITING RESPONSE state. It specifies the maximum time
during which no MultiplexEntrySendAck or
MultiplexEntrySendReject message may be received.
|
| h245ConfigT105Timer |
.0.0.8.341.1.0.3.1.1.1.1.5 |
|
This timer is used during Round Trip Delay procedure. This timer is used
in the AWAITING RESPONSE state. It specifies the maximum time during
which no RoundTripDelayResponse message may be received.
|
| h245ConfigT106Timer |
.0.0.8.341.1.0.3.1.1.1.1.6 |
|
This timer is used during Master Slave Determination procedure. This
timer is used in the OUTGOING AWAITING RESPONSE state and during the
INCOMING AWAITING RESPONSE state. It specifies the maximum time during
which no acknowledgement message may be received.
|
| h245ConfigT107Timer |
.0.0.8.341.1.0.3.1.1.1.1.7 |
|
This timer is used during Request Multiplex Entry procedure. This timer
is used during the AWAITING RESPONSE state. It specifies the maximum
time during which no RequestMultiplexEntryAck or
RequestMultiplexEntryReject message may be received.
|
| h245ConfigT108Timer |
.0.0.8.341.1.0.3.1.1.1.1.8 |
|
This timer is used during SEND Logical Channel procedure. This timer is
used in the AWAITING RESPONSE state. It specifies the maximum time
during which no RequestMultiplexEntryAck or RequestMultiplexEntryReject
message may be received.
|
| h245ConfigT109Timer |
.0.0.8.341.1.0.3.1.1.1.1.9 |
|
This timer is used during Mode Request procedure. This timer is used in
the AWAITING RESPONSE state. It specifies the maximum time during which
no RequestModeAck or RequestModeReject message may be received.
|
| h245ConfigN100Counter |
.0.0.8.341.1.0.3.1.1.1.1.10 |
|
This counter specifies the maximum number of times that
MasterSlaveDetermination messages will be sent during the
OUTGOING AWAITING RESPONSE state.
|
| h245ControlChannelNumberOfListenPorts |
.0.0.8.341.1.0.3.1.2.1.1.1 |
|
The number of H245 Listen ports. These ports are
used for the remote entity to send a connect on
|
| h245ControlChannelMaxConnections |
.0.0.8.341.1.0.3.1.2.1.1.2 |
|
The number of maximum active h245 channels allowed.
|
| h245ControlChannelNumberOfListenFails |
.0.0.8.341.1.0.3.1.2.1.1.3 |
|
The number of Listen fails. The fail could be due
to exhaustion of system resources
|
| h245ControlChannelNumberOfActiveConnections |
.0.0.8.341.1.0.3.1.2.1.1.4 |
|
The number of the active H245 connections.
|
| h245ControlChannelMasterSlaveMaxRetries |
.0.0.8.341.1.0.3.1.2.1.1.5 |
|
The number of maximum master slave retries. Reties
are needed when the result of master slave process
is indeterminate
|
| h245ControlChannelConnectionAttemptsFail |
.0.0.8.341.1.0.3.1.2.1.1.6 |
|
The number of failures when trying to connect to
a listen port.
|
| h245ControlChanneMasterSlavelDeterminations |
.0.0.8.341.1.0.3.1.2.1.1.7 |
|
The number of MSD messages sent from a MSDSE to a peer MSDSE
for master/slave determination purpose.
|
| h245ControlChannelMasterSlaveAcks |
.0.0.8.341.1.0.3.1.2.1.1.8 |
|
The number of acks that are used to confirm whether the terminal is
the master terminal or the slave terminal, as indicated by decision.
When decision is of type master, the terminal receiving this message
is the master terminal and when decision is of type slave, it is the
slave terminal.
|
| h245ControlChannelMasterSlaveRejects |
.0.0.8.341.1.0.3.1.2.1.1.9 |
|
The number of rejects of the MasterSlaveDetermination message.
|
| h245ControlChannelMasterSlaveT106Rejects |
.0.0.8.341.1.0.3.1.2.1.1.10 |
|
The number of rejects of the MasterSlaveDetermination message. When
the cause is of type identicalNumbers, the rejection was due to the
random numbers being equivalent and the terminal types being the same.
|
| h245ControlChannelMasterSlaveMSDRejects |
.0.0.8.341.1.0.3.1.2.1.1.11 |
|
The number of MSD rejects of the MasterSlaveDetermination message.
Rejects can happen due to different reasons like
identical random number after maximum tries, timeouts...
|
| h245ControlChannelNumberOfMasterSlaveInconsistentFieldRejects |
.0.0.8.341.1.0.3.1.2.1.1.12 |
|
The number of rejects of the MasterSlaveDetermination
message. The cause is due to conflict in the status that
both entities arrive to.
|
| h245ControlChannelMasterSlaveMaxCounterRejects |
.0.0.8.341.1.0.3.1.2.1.1.13 |
|
The number of rejects of the MasterSlaveDetermination
message. There are many reasons why the rejection could
happen.
|
| h245ControlChannelMasterSlaveReleases |
.0.0.8.341.1.0.3.1.2.1.1.14 |
|
The number of rejects due to a time out.
|
| h245ControlChannelNumberOfTunnels |
.0.0.8.341.1.0.3.1.2.1.1.15 |
|
The number of the active H245 tunnels.
|
| h245ControlChannelSrcAddressTag |
.0.0.8.341.1.0.3.1.2.2.1.1 |
|
It describes the type of address (IP v4, IPv6...)
of the source
|
| h245ControlChannelSrcTransporTAddress |
.0.0.8.341.1.0.3.1.2.2.1.2 |
|
Source transport address.
|
| h245ControlChannelDesTAddressTag |
.0.0.8.341.1.0.3.1.2.2.1.3 |
|
It describes the type of address (IP v4, IPv6...)
of the source
|
| h245ControlChannelDestTransporTAddress |
.0.0.8.341.1.0.3.1.2.2.1.4 |
|
Remote transport address.
|
| h245ControlChannelIndex |
.0.0.8.341.1.0.3.1.2.2.1.5 |
|
It is an arbitrary number that is being incremented
by 1 for every entry in this table
|
| h245ControlChannelMSDState |
.0.0.8.341.1.0.3.1.2.2.1.6 |
|
It describes the state of the master slave
determination procdure. It can be OUTGOING WAITING
RESPONSE, INCOMING WAITING RESPONSE, IDLE
|
| h245ControlChannelTerminalType |
.0.0.8.341.1.0.3.1.2.2.1.7 |
|
Terminal type represents the type of H.323 terminal:
50 - terminal without MC
60 - gateway without MC
70 - terminal with MC but without MP
80 - gateway with MC but without MP
120 - gatekeeper with MC but without MP
160 - MCU with MC but without MP
90 - gateway with MC and Data MP
130 - gatekeeper with MC and Data MP
170 - MCU with MC and Data MP
100 - gateway containing MC with Data and audio MP
140 - gatekeeper containing MC with Data and audio MP
180 - MCU containing MC with Data and audio MP
110 - gateway containing MC with Data, Audio and Video MP
150 - gatekeeper containing MC with Data, Audio and Video MP
190 - MCU containing MC with Data, Audio and Video MP
240 - entity with active MC .
|
| h245ControlChannelNumberOfMSDRetries |
.0.0.8.341.1.0.3.1.2.2.1.8 |
|
The number of tries of master slave determination
before a meaningful result is concluded.
|
| h245ControlChannelIsTunneling |
.0.0.8.341.1.0.3.1.2.2.1.9 |
|
This variable indicates if tunneling is used for this channel.
|
| h245CapExchangeSets |
.0.0.8.341.1.0.3.1.3.1.1.1 |
|
The total number of TerminalCapabilitySets that were sent and received
by the local CESE (Capability Exchange Signalling Entity). A
TerminalCapabilitySet is used for the intention to signal a terminal's
capabilities to ensure that the only multimedia signals to be
transmitted are those that can be received and treated appropriately by
the receive terminal.
|
| h245CapExchangeAcks |
.0.0.8.341.1.0.3.1.3.1.1.2 |
|
The total number of TerminalCapabilitySetAcks that were sent and
received by local CESE (Capability Exchange Signalling Entity). A
TerminalCapabilitySetAck is used as a confirmation for a
TerminalCapabilitySet that was successfully received and processed.
|
| h245CapExchangeRejects |
.0.0.8.341.1.0.3.1.3.1.1.3 |
|
The total number of TerminalCapabilitySetRejects that were sent and
received by the local CESE (Capability Exchange Signalling Entity). A
TerminalCapabilitySetReject is used to indicate a failure due to a
specific error for a TerminalCapabilitySet that was received, but, yet
to be fully processed.
|
| h245CapExchangeRejectUnspecified |
.0.0.8.341.1.0.3.1.3.1.1.4 |
|
The total number of TerminalCapabilitySetRejects that were sent and
received by the local CESE (Capability Exchange Signalling Entity) with
the cause value set to unspecified. This means that there was no cause
for the rejection of a TerminalCapabilitySet specified.
|
| h245CapExchangeRejectUndefinedTableEntryUsed |
.0.0.8.341.1.0.3.1.3.1.1.5 |
|
The total number of TerminalCapabilitySetRejects that were sent and
received by the local CESE (Capability Exchange Signalling Entity) with
the cause value set to undefinedTableEntryUsed. This means that the
cause of the rejection of a TerminalCapabilitySet was due to a
capability descriptor made reference to a capability table entry number
in the capability table of the TerminalCapabilitySet was not defined.
|
| h245CapExchangeRejectDescriptorCapacityExceeded |
.0.0.8.341.1.0.3.1.3.1.1.6 |
|
The total number of TerminalCapabilitySetRejects that were sent and
received by the local CESE (Capability Exchange Signalling Entity) with
the cause value set to descriptorCapacityExceeded. This means that the
cause of the rejection of a TerminalCapabilitySet was due to a terminal
incapable of storing all of the information from the
capabilityDescriptors of the TerminalCapabilitySet.
|
| h245CapExchangeRejectTableEntryCapacityExeeded |
.0.0.8.341.1.0.3.1.3.1.1.7 |
|
The total number of TerminalCapabilitySetRejects that were sent and
received by the local CESE (Capability Exchange Signalling Entity) with
the cause value set to tableEntryCapacityExceeded. This means that the
cause of the rejection of a TerminalCapabilitySet was due to a terminal
incapable of storing some (indicated in the highestEntryNumberProcessed)
or all (indicated in the noneProcessed) of the information from the
capability table of the TerminalCapabilitySet.
|
| h245CapExchangeReleases |
.0.0.8.341.1.0.3.1.3.1.1.8 |
|
The total number of TerminalCapabilitySetReleases that were sent and
received by the local CESE (Capability Exchange Signalling Entity).
This means that a response for a TerminalCapabilitySet was not
received/issued in time. A timer expiry had occurred for the local
CESE.
|
| h245CapExchangeDirection |
.0.0.8.341.1.0.3.1.3.2.1.1 |
|
Represents either the local incoming CESE or the local outgoing CESE
(Capability Exchange Signalling Entity).
|
| h245CapExchangeState |
.0.0.8.341.1.0.3.1.3.2.1.2 |
|
The current state of this CESE (Capability Exchange Signalling Entity).
|
| h245CapExchangeProtocolId |
.0.0.8.341.1.0.3.1.3.2.1.3 |
|
The version of the H.245 protocol used. This specifies how H.245
messages are formatted and used.
|
| h245CapExchangeRejectCause |
.0.0.8.341.1.0.3.1.3.2.1.4 |
|
The latest reject cause value extracted from the latest
TerminalCapabilitySetReject.
|
| h245CapExchangeMultiplexCapability |
.0.0.8.341.1.0.3.1.3.2.1.5 |
|
The latest multiplexCapability extracted from a TerminalCapabilitySet.
|
| h245CapExchangeCapability |
.0.0.8.341.1.0.3.1.3.2.1.6 |
|
The latest capabilityTable extracted from the latest TerminalCapabilitySet.
|
| h245CapExchangeCapabilityDescriptors |
.0.0.8.341.1.0.3.1.3.2.1.7 |
|
The latest capabilityDescriptors extracted from the latest
TerminalCapabilitySet.
|
| h245LogChannelsChannelNumber |
.0.0.8.341.1.0.3.1.4.1.1.1 |
|
The forwardLogicalChannelNumber used to distinguish
this media channel by this LCSE (Uni or Bi-directional
Logical Channel Signalling Entity).
|
| h245LogChannelsChannelDirection |
.0.0.8.341.1.0.3.1.4.1.1.2 |
|
Represents the direction of this media channel used
by this LCSE (Uni or Bi-directional Logical Channel
Signalling Entity) .
|
| h245LogChannelsIndex |
.0.0.8.341.1.0.3.1.4.1.1.3 |
|
A unique value representing this media channel.
|
| h245LogChannelsChannelState |
.0.0.8.341.1.0.3.1.4.1.1.4 |
|
The current state of the media channel which also
represents the state of this LCSE (Uni or Bi-directional
Logical Channel Signalling Entity).
|
| h245LogChannelsMediaTableType |
.0.0.8.341.1.0.3.1.4.1.1.5 |
|
The actual media or data type used for this
logical channel.
|
| h245LogChannelsSessionId |
.0.0.8.341.1.0.3.1.4.2.1.1 |
|
A unique RTP or T.120 Session Identifier in a conference.
It is used by the transmitter to refer to the session to
which the logical channel applies.
|
| h245LogChannelsAssociateSessionId |
.0.0.8.341.1.0.3.1.4.2.1.2 |
|
This is used to associate one session with another in a
conference. A typical use will be to associate an audio
session with a video session to indicate which sessions
to process for lip synchronization.
|
| h245LogChannelsMediaChannel |
.0.0.8.341.1.0.3.1.4.2.1.3 |
|
Indicates a transporTAddress to be used for the logical
channel.
|
| h245LogChannelsMediaGuaranteedDelivery |
.0.0.8.341.1.0.3.1.4.2.1.4 |
|
Indicates whether or not the underlying media transport
should be selected to provide or not to provide
guaranteed delivery of data.
|
| h245LogChannelsMediaControlChannel |
.0.0.8.341.1.0.3.1.4.2.1.5 |
|
Indicates the media control channel in which the sender
of the open logical channel will be listening for media
control messages for this session. This field is
present only when a media control channel is required.
|
| h245LogChannelsMediaControlGuaranteedDelivery |
.0.0.8.341.1.0.3.1.4.2.1.6 |
|
Indicates whether or not the underlying media control
transport should be selected to provide or not to
provide guaranteed delivery of data. This field is
present only when a media control channel is required.
|
| h245LogChannelsSilenceSuppression |
.0.0.8.341.1.0.3.1.4.2.1.7 |
|
Indicates whether the transmitter stops sending packets
during times of silence for bandwidth reasons. This
can only be enabled for an audio channel only.
|
| h245LogChannelsDestination |
.0.0.8.341.1.0.3.1.4.2.1.8 |
|
Indicates the terminal label (composed of a mcu number
and a terminal number) of the destination if one
has been assigned.
|
| h245LogChannelsDynamicRTPPayloadType |
.0.0.8.341.1.0.3.1.4.2.1.9 |
|
Indicates a dynamic payload value which is used in H.323
for the H.225.0 alternative H.261 video packetization
scheme. This field is present only when a dynamic RTP
payload is in use.
|
| h245LogChannelsH261aVideoPacketization |
.0.0.8.341.1.0.3.1.4.2.1.10 |
|
Indicates that the H.261 alternative RTP payload form is
in use as described in H.225.0.
|
| h245LogChannelsRTPPayloadDescriptor |
.0.0.8.341.1.0.3.1.4.2.1.11 |
|
If the rfc-number is chosen, it indicates the offical
document of the IETF in which the payload format is
defined (OID). Obsolete RFCs should not be referenced here.
If the oid component is chosen, this identifies a payload
format specified as part of a Recommendation defined by
the ITU or an International Standard defined by the ISO
and registered in the respective document under this
Object Indentifier.
|
| h245LogChannelsRTPPayloadType |
.0.0.8.341.1.0.3.1.4.2.1.12 |
|
Indicates which payload type value used. If the dynamic
payload type is used, the values of this field and the
logChannelsDynamicRTPPayloadType should match.
|
| h245LogChannelsTransportCapability |
.0.0.8.341.1.0.3.1.4.2.1.13 |
|
Indicates optional transport capabilites such as quality
of service and median channel type capabilites.
|
| h245LogChannelsRedundancyEncoding |
.0.0.8.341.1.0.3.1.4.2.1.14 |
|
Indicates which redundancy encoding modes are supported (if any).
The redundancyEncoding indicates that the redundant encoding method
indicated in this parameter is to be used for this logical channel.
The primary encoding is defined by the dataType of the
forwardLogicalChannelParameters or the reverseLogicalChannelParameters,
respectively. The type of redundancy encoding to be applied for this
logical channel is identified by the redundancyEncodingMethod parameter,
the secondary encoding is specified in the secondaryEncoding parameter.
The DataType (audio, video, etc.) selected for both primary and
secondary encoding shall match and shall be in accordance with the
redundancyEncodingMethod selected.
|
| h245LogChannelsSrcTerminalLabel |
.0.0.8.341.1.0.3.1.4.2.1.15 |
|
This is used to identify the terminal number of the sender of the
OpenLogicalChannel message.
|
| h245LogChanOpenLogChanTotalRequests |
.0.0.8.341.1.0.3.1.4.3.1.1 |
|
The total number of attempts to open a uni-directional
logical channel between an outgoing LCSE and a peer
incoming LCSE and a bi-directional logical channel
between an outgoing B-LCSE and a peer incoming B-LCSE.
|
| h245LogChanOpenLogChanAcks |
.0.0.8.341.1.0.3.1.4.3.1.2 |
|
The total number of confirmations to accept an open
logical channel request. This would represent the
final stage of establishing a uni-directional channel
that can be used for transmission.
|
| h245LogChanOpenLogChanConfirms |
.0.0.8.341.1.0.3.1.4.3.1.3 |
|
The total number of confirmations used for the purpose
of bi-directional channel signaling that the
reverse channel is open and can be used for
transmission. This represents the final stage of
establishing a bi-directional channel that can
be used for transmission in both directions.
|
| h245LogChanOpenLogChanRejects |
.0.0.8.341.1.0.3.1.4.3.1.4 |
|
The total number of rejections used as a response
to a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE.
|
| h245LogChanOpenLogChanRejectUnspecified |
.0.0.8.341.1.0.3.1.4.3.1.5 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was unspecified.
|
| h245LogChanOpenLogChanRejectUnsuitableReverseParameters |
.0.0.8.341.1.0.3.1.4.3.1.6 |
|
The total number of rejections used as a response to
a request to open a bi-directional logical
channel from a B-LCSE when the reason for the
rejection was the reverseLogicalChannelParameters
in the OpenLogicalChannel were inappropriate.
|
| h245LogChanOpenLogChanRejectDataTypeNotSupported |
.0.0.8.341.1.0.3.1.4.3.1.7 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a terminal not capable of supporting
the desired dataType.
|
| h245LogChanOpenLogChanRejectDataTypeNotAvailable |
.0.0.8.341.1.0.3.1.4.3.1.8 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a terminal not capable of supporting
the desired dataType simultaneously with the dataTypes
of logical channels that are already open.
|
| h245LogChanOpenLogChanRejectUnknownDataType |
.0.0.8.341.1.0.3.1.4.3.1.9 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a terminal not understanding the
dataType indicated in the OpenLogicalChannel.
|
| h245LogChanOpenLogChanRejectDataTypeALCombinationNotSupported |
.0.0.8.341.1.0.3.1.4.3.1.10 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a terminal not capable of supporting
the dataType indicated in OpenLogicalChannel simultaneously
with the Adaptation Layer type indicated in
H223LogicalChannelParameters.
|
| h245LogChanOpenLogChanRejectMulticastChannelNotAllowed |
.0.0.8.341.1.0.3.1.4.3.1.11 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a multicast Channel that could
not be opened.
|
| h245LogChanOpenLogChanRejectInsuffientBandwdith |
.0.0.8.341.1.0.3.1.4.3.1.12 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was because permission to use the requested
bandwidth for the logical channel was denied.
|
| h245LogChanOpenLogChanRejectSeparateStackEstablishmentFailed |
.0.0.8.341.1.0.3.1.4.3.1.13 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a request to run the data portion
of a call on a separate stack failed.
|
| h245LogChanOpenLogChanRejectInvalidSessionID |
.0.0.8.341.1.0.3.1.4.3.1.14 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to an attempt by a slave to set
the SessionID when opening a logical channel to the master.
|
| h245LogChanOpenLogChanRejectMasterSlaveConflict |
.0.0.8.341.1.0.3.1.4.3.1.15 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to an attempt by a slave to open a
logical channel in which the master has determined a
conflict may occur.
|
| h245LogChanOpenLogChanRejectWaitForCommunicationMode |
.0.0.8.341.1.0.3.1.4.3.1.16 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to an attempt to open a logical channel
before MC has transmitted the CommunicationModeCommand.
|
| h245LogChanOpenLogChanRejectInvalidDependentChannel |
.0.0.8.341.1.0.3.1.4.3.1.17 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to an attempt to open a logical channel
with a dependent channel specified which is not present.
|
| h245LogChansOpenLogChanRejectReplacementForRejected |
.0.0.8.341.1.0.3.1.4.3.1.18 |
|
The total number of rejections used as a response to
a request to open a uni or a bi-directional logical
channel from a LCSE or B-LCSE when the reason for the
rejection was due to a logical channel of the type
attempted cannot be opened using the replacementFor
parameter.
|
| h245LogChanCloseLogChannels |
.0.0.8.341.1.0.3.1.4.4.1.1 |
|
The number of attempts made by the outgoing LCSE or B-LCSE to close
a logical channel between two peer LCSEs or B-LCSEs.
Note - In the case of a bi-directional logical channel, this closes both
forward and reverse channels. It is not possible to close one and not
the other.
|
| h245LogChanCloseLogChanAcks |
.0.0.8.341.1.0.3.1.4.4.1.2 |
|
The number of attempts made to confirm the closing of a logical channel
connection.
|
| h245LogChanCloseLogChanRequests |
.0.0.8.341.1.0.3.1.4.4.1.3 |
|
The number of attempts made by the outgoing CLCSE to request the closing
of a logical channel connection between two peer LCSEs.
|
| h245LogChanCloseLogChanRequestsAcks |
.0.0.8.341.1.0.3.1.4.4.1.4 |
|
The number of attempts made by the incoming CLCSE to indicate that the
logical channel connection will be closed.
|
| h245LogChanCloseLogChanRequestRejects |
.0.0.8.341.1.0.3.1.4.4.1.5 |
|
The number of attempts made by the incoming CLCSE to indicate that
the logical channel connection will not be closed.
The only valid cause value for rejecting to close a channel is
unspecified.
|
| h245LogChanCloseLogChanRequestReleases |
.0.0.8.341.1.0.3.1.4.4.1.6 |
|
The number of attempts made by the outgoing CLCSE in the case of a time
out.
|
| h245MiscRTDState |
.0.0.8.341.1.0.3.1.6.1.1.1 |
|
The state of the round trip delay. It can be either
idle or waiting for response.
|
| h245MiscT105TimerExpired |
.0.0.8.341.1.0.3.1.6.1.1.2 |
|
Round trip delay timer expired waiting for a respinse
from the other entity.
|
| h245MiscLastRTDRequestSent |
.0.0.8.341.1.0.3.1.6.1.1.3 |
|
Information about the last round trip delay request
sent.
|
| h245MiscLastRTDRequestRcvd |
.0.0.8.341.1.0.3.1.6.1.1.4 |
|
Information about the last round trip delay request
received.
|
| h245MiscLastRTDResponseSent |
.0.0.8.341.1.0.3.1.6.1.1.5 |
|
Information about the last round trip delay response
sent.
|
| h245MiscLastRTDResponseRcvd |
.0.0.8.341.1.0.3.1.6.1.1.6 |
|
Information about the last round trip delay response
received.
|
| h245MiscMaintenanceLoopDirection |
.0.0.8.341.1.0.3.1.6.2.1.1 |
|
The direction could be either incoming or outgoing.
|
| h245MiscMLState |
.0.0.8.341.1.0.3.1.6.2.1.2 |
|
The state of the channel which can be: not looped,
waiting to be looped or looped.
|
| h245MiscNumberOfRequests |
.0.0.8.341.1.0.3.1.6.2.1.3 |
|
Number of loop requests on that channel.
|
| h245MiscNumberOfAcks |
.0.0.8.341.1.0.3.1.6.2.1.4 |
|
Number of maintenance loop acks on the channel.
|
| h245MiscLastMLRequestOrAckType |
.0.0.8.341.1.0.3.1.6.2.1.5 |
|
The type of the last request or response received.
The type can be either media or logical channel loop.
|
| h245MiscMLMediaOrLogicalChannelLoopRejectChannelNumber |
.0.0.8.341.1.0.3.1.6.2.1.6 |
|
If the loop rejecte is of type media loop or logical
channel loop then this represents the channel number
for the logical channel.
|
| h245MiscNumberOfRejects |
.0.0.8.341.1.0.3.1.6.2.1.7 |
|
Number of loop requests that got rejected.
|
| h245MiscLastRejectType |
.0.0.8.341.1.0.3.1.6.2.1.8 |
|
The type of the last reject for the loop request.
|
| h245MiscErrorCode |
.0.0.8.341.1.0.3.1.6.2.1.9 |
|
The error code that caused the rejection of the loop
request.
|
| h245ConferenceConferenceId |
.0.0.8.341.1.0.3.1.5.1.1.1 |
|
The conference identifier.
|
| h245ConferenceTerminalLabel |
.0.0.8.341.1.0.3.1.5.1.1.2 |
|
The terminal label of this terminal
|
| h245ConferenceControlChannelIndex |
.0.0.8.341.1.0.3.1.5.1.1.3 |
|
The index of the control channel table that
identifies the control channel for the conference.
|
| h245ConferenceBroadcaster |
.0.0.8.341.1.0.3.1.5.1.1.4 |
|
The indicator of the terminal being a broadcaster.
|
| h245ConferenceConferenceChair |
.0.0.8.341.1.0.3.1.5.1.1.5 |
|
The indicator of the terminal being a conference chair.
|
| h245ConferenceMultipoint |
.0.0.8.341.1.0.3.1.5.1.1.6 |
|
The indicator of the conference being a multipoint.
|
| h245ConferenceBroadcastMyLogicalChannel |
.0.0.8.341.1.0.3.1.5.2.1.1 |
|
The number of attempts made by a terminal to transmit MCV command to
force an associated MCU to broadcast its video signal used to transmit
the picture of a chairman or VIP, alternatively to hold a picture
source during the transmission of graphics.
|
| h245ConferenceCancelBroadcastMyLogicalChannel |
.0.0.8.341.1.0.3.1.5.2.1.2 |
|
The number of attempts made by a terminal to cancel MCV command.
|
| h245ConferenceSendThisSource |
.0.0.8.341.1.0.3.1.5.2.1.3 |
|
The number of attempts made by a terminal to send VCS command to MCU to
cause transmission to itself of the video from the terminal whose
identity number follows VCS.
|
| h245ConferenceCancelSendThisSource |
.0.0.8.341.1.0.3.1.5.2.1.4 |
|
The number of attempts made by a terminal to cancel VCS and return to
automatic video switching at the MCU.
|
| h245ConferenceDropConference |
.0.0.8.341.1.0.3.1.5.2.1.5 |
|
The number of attempts made by a terminal that is chair-control to drop
all terminals from the conference.
|
| h245ConferenceEqualiseDelay |
.0.0.8.341.1.0.3.1.5.2.1.6 |
|
The same meaning as the command ACE in H.230.
|
| h245ConferenceZeroDelay |
.0.0.8.341.1.0.3.1.5.2.1.7 |
|
The same meaning as the command ACZ defined in H.230.
|
| h245ConferenceMultipointModeCommand |
.0.0.8.341.1.0.3.1.5.2.1.8 |
|
The number of attempts made by the MCU to send request to a terminal to
comply with all MCU requestMode requests.
|
| h245ConferenceCancelMultipointModeCommand |
.0.0.8.341.1.0.3.1.5.2.1.9 |
|
The number of attempts made by the MCU to send a cancelation of a
MultipointModeCommand.
|
| h245ConferenceVideoFreezePicture |
.0.0.8.341.1.0.3.1.5.2.1.10 |
|
The number of commands that are sent/received to/from the video decoder
to complete updating the current video frame and subsequently display
the frozen picture until receipt of the appropriate freeze-picture
release control signal.
|
| h245ConferenceVideoFastUpdatePicture |
.0.0.8.341.1.0.3.1.5.2.1.11 |
|
The number of commands sent/received to enter the fast update mode.
|
| h245ConferenceVideoFastUpdateGOB |
.0.0.8.341.1.0.3.1.5.2.1.12 |
|
The number of commands sent/received by the video encoder to fast update
one or more GOBs.
|
| h245ConferenceVideoTemporalSpatialTradeOff |
.0.0.8.341.1.0.3.1.5.2.1.13 |
|
The number of commands sent/received by video encoder to change its
trade off between temporal and spatial resolution.
|
| h245ConferenceVideoSendSyncEveryGOB |
.0.0.8.341.1.0.3.1.5.2.1.14 |
|
The number of commands sent/received by video encoder to use sync
for every GOB until the cancel command is received.
|
| h245ConferenceVideoFastUpdateMB |
.0.0.8.341.1.0.3.1.5.2.1.15 |
|
The number of sent/received by video encoder to perform a fast update of
one or more MBs.
|
