| h320TerminalSystem |
.0.0.8.341.1.0.2.2.1.1 |
|
A textual description of the terminal. Name of
manufacturer.
|
| h320TerminalHWVersionNo |
.0.0.8.341.1.0.2.2.1.2 |
|
Hardware version number.
|
| h320TerminalSWVersionNo |
.0.0.8.341.1.0.2.2.1.3 |
|
Software version number.
|
| h320SystemContact |
.0.0.8.341.1.0.2.2.1.4 |
|
The textual identification of the contact person
for this managed node, together with information
on how to contact this person.
|
| h320Systemt35CountryCode |
.0.0.8.341.1.0.2.2.1.5 |
|
Country code, per T.35.
|
| h320Systemt35CountryCodeExtention |
.0.0.8.341.1.0.2.2.1.6 |
|
Assigned nationally.
|
| h320Systemt35ManufacturerCode |
.0.0.8.341.1.0.2.2.1.7 |
|
Assigned nationally.
|
| h320SystemLocation |
.0.0.8.341.1.0.2.2.1.8 |
|
The physical location of this system. For instance, closet,
terminal room and so on
|
| h320SystemUptime |
.0.0.8.341.1.0.2.2.1.9 |
|
The amount of time (in hundredths of a second) since
this H320 terminal was last initialized. Note that this
is different from sysUpTime in MIB-II because
sysUpTime is the uptime of the network management
portion of the system.
|
| h320SystemLocalTime |
.0.0.8.341.1.0.2.2.1.10 |
|
The local date and time of day.
|
| h320SystemDiagnostics |
.0.0.8.341.1.0.2.2.1.11 |
|
Indicates the results of the last diagnostic routine
performed.
noResults(1) No diagnostic has yet been performed,
passed(2) the diagnostic has been passed,
hardwareFault(3) Hardware fault was detected,
softwareFault(4) Software fault was detected.
|
| h320SystemStatus |
.0.0.8.341.1.0.2.2.1.12 |
|
General status of the terminal
|
| h320SystemIfType |
.0.0.8.341.1.0.2.2.1.13 |
|
The interface type on which this terminal can be called.
The interface type identified by this value is the
same type of as the ifType from Interface Table
in RFC1213. It should only use ifTypes - ds1, e1,
basicISDN, primaryISDN.
|
| h320TerminalConfigSiteName |
.0.0.8.341.1.0.2.2.2.1 |
|
Name of the site where the H320 terminal is located.
For instance, conference room 1 in Austin, or New York,
and so on. sysLocation provides the location information
for the maintenance people and this object informs where
the conference participants are.
|
| h320TerminalConfigVideoSystem |
.0.0.8.341.1.0.2.2.2.2 |
|
Video format standard used by the terminal
|
| h320TerminalConfigIPAddress |
.0.0.8.341.1.0.2.2.2.3 |
|
The IP address of the h.320 terminal.
|
| h320TerminalConfigISDNSwitchType |
.0.0.8.341.1.0.2.2.2.4 |
|
Type of ISDN switch interface to the h.320 terminal.
Switch types are specified in ISDN-MIB.
|
| h320TerminalConfigISDNAddrNumber |
.0.0.8.341.1.0.2.2.2.5 |
|
The number of addresses that each terminal has.
|
| configISDNAddrEntry |
.0.0.8.341.1.0.2.2.2.6.1 |
|
AN ISDN address row.
|
| h320TerminalConfigEnableNotifications |
.0.0.8.341.1.0.2.2.2.7 |
|
Indicates whether notifications should be generated for
this terminal. The default is disabled.
|
| h320CallSiteNumber |
.0.0.8.341.1.0.2.2.3.1 |
|
The number of site entries that this system
contains.
|
| h320CallSiteXferNextIndex |
.0.0.8.341.1.0.2.2.3.2 |
|
Identifies the next value of h320CallSiteIndex to be used
in a row creation attempt for the h320CallSiteTable.
If new rows cannot be created, this object will
have a value of 0.
|
| h320CallSiteEntry |
.0.0.8.341.1.0.2.2.3.3.1 |
|
A video conference site row. Rows are created by
an SNMP SET request setting the value of
h320SiteRowStatus to 'createandGo. Rows are deleted
by an SNMP SET request setting the value of
h320SiteRowStatus to 'destroy'.
|
| h320CallSiteISDNAddrEntry |
.0.0.8.341.1.0.2.2.3.4.1 |
|
A video conference site row. Rows are created by
an SNMP SET request setting the value of
h320AddrRowStatus to 'createandGo'. Rows are deleted
by an SNMP SET request setting the value of
h320AddrRowStatus to 'destroy'
|
| h320TerminalcontrolAdmin |
.0.0.8.341.1.0.2.2.4.1 |
|
The desired state of the H320 terminal.
Setting the value if this object to these values
will have the following actions:
run(1) The H320 terminal will enter the
run state,
reset(2) The H320 terminal will reset,
diagnose(3) Will activate the diagnostic routine,
stop(4) Will halt the H320 terminal.
|
| h320TerminalcontrolCallSetUp |
.0.0.8.341.1.0.2.2.4.2 |
|
Dial another video conference terminal. Set this value
to the index of the site of the video conference site
you want to dial in the Site Table in the
h320CallSignalingMIB and the system will be dialed.
|
| h320TerminalcontrolCallHangup |
.0.0.8.341.1.0.2.2.4.3 |
|
Hang up the video conference call in progress now.
|
| h320TerminalControlEnableLocalLoopback |
.0.0.8.341.1.0.2.2.4.4 |
|
Enable or disable local loopback on a video
conference system. Local loopbacks loop back the
audio, video and data streams in a call. Once looped
back, a new call will show up and the user can
observe the audio/video/data rates to assure that
these components are working properly.
|
| h320TerminalControlEnableRemoteLoopback |
.0.0.8.341.1.0.2.2.4.5 |
|
Enable or disable remote loopback on a video
conference system. Remote loopbacks loop back the
audio and video streams from the remote system in
a call.. When the remote system calls in, a new call
will show and the user can observe the audio/video/data
rates to assure that these components are coming in
properly from the remote system.
|
| h320TerminalConfigAddrIndex |
.0.0.8.341.1.0.2.2.2.6.1.1 |
|
A unique value for each ISDN address entry.
the value ranges between 1 and the value of
h320TerminalConfigISDNAddrNumber.
|
| h320TerminalConfigISDNAddress |
.0.0.8.341.1.0.2.2.2.6.1.2 |
|
ISDN port address.
|
| h320TerminalConfigISDNSPID |
.0.0.8.341.1.0.2.2.2.6.1.3 |
|
ISDN port SPID.
|
| h320CallSiteIndex |
.0.0.8.341.1.0.2.2.3.3.1.1 |
|
A unique value for each video conference Site
entry. The value ranges between 1 and the value
of h320SiteNumber.
|
| h320CallSiteSiteName |
.0.0.8.341.1.0.2.2.3.3.1.2 |
|
A textual string assigning a name to a video
conference system.
|
| h320CallSiteSiteIfType |
.0.0.8.341.1.0.2.2.3.3.1.3 |
|
The interface type on which this site can be called.
The interface type identified by this value is the
same type of as the ifType from Interface Table
in RFC1213. It should only use ifTypes - ds1, e1,
basicISDN, primaryISDN.
|
| h320CallSiteSiteLineRate |
.0.0.8.341.1.0.2.2.3.3.1.4 |
|
The line rate that the terminal can be called.
|
| h320CallSiteCallMode |
.0.0.8.341.1.0.2.2.3.3.1.5 |
|
1 means the remote terminal supports
the autoconfiguration.
2 means the manual configuration is required to
call the remote terminal. In this case, the
following audio, video and data mode shall be
used for the manual configuration.
|
| h320CallSiteVideoMode |
.0.0.8.341.1.0.2.2.3.3.1.6 |
|
A video mode for manual configuration.
|
| h320CallSiteAudioMode |
.0.0.8.341.1.0.2.2.3.3.1.7 |
|
An audio mode for manual configuration.
|
| h320CallSiteISDNAddrNumber |
.0.0.8.341.1.0.2.2.3.3.1.8 |
|
The number of ISDN addresses needed to make a
call to the remote terminal.
|
| h320CallSiteRowStatus |
.0.0.8.341.1.0.2.2.3.3.1.9 |
|
The row status of the entry. This object is required
to create or delete rows administratively.
An agent implementing this object is not required to
support the values 'createAndWait' and 'notInService'.
|
| h320CallSiteAddrIndex |
.0.0.8.341.1.0.2.2.3.4.1.1 |
|
A unique value for each ISDN address entry.
The value ranges between 1 and the value
of h320ISDNAddrNumber the base table.
|
| h320CallSiteISDNAddress |
.0.0.8.341.1.0.2.2.3.4.1.2 |
|
A textual string assigning an address of the
conference system.
|
| h320CallSiteAddrRowStatus |
.0.0.8.341.1.0.2.2.3.4.1.3 |
|
The row status of the entry. This object is required
to create or delete rows administratively.
An agent implementing this object is not required to
support the values 'createAndWait' and 'notInService'.
|
