| etsysDot11ExtLinkTestEntry |
.1.3.6.1.4.1.5624.1.2.9.1.1.1.1 |
|
An Entry (conceptual row) in the LinkTest Table.
By means of message transmission between requester
and responder, the communication quality between the
two stations can be determined. The requester and
responder can be any combination of AP and STA except
STA to STA in an Infrastructure Network (network which
has at least one AP present.
|
| etsysDot11ExtGeneralEntry |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1 |
|
An Entry (conceptual row) in the Dot11General Table.
This allows for multiple instances of radio cards
in the Access Point.
|
| etsysDot11ExtBldgEntry |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1 |
|
An Entry (conceptual row) in the Dot11Bldg Table.
A collection of objects containing information for activating
and using the Access Point in Point-to-MultiPoint mode.
|
| etsysDot11ExtWEPDefaultKeysEntry |
.1.3.6.1.4.1.5624.1.2.9.1.4.1.1 |
|
An Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey.
|
| etsysDot11ExtWEPEnhancedEntry |
.1.3.6.1.4.1.5624.1.2.9.1.4.2.1 |
|
An Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey.
|
| etsysDot11ExtOIDNotInEffectEntry |
.1.3.6.1.4.1.5624.1.2.9.1.5.1.1 |
|
|
| etsysDot11ExtLTRemoteStationMAC |
.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.1 |
|
The MAC address for the remote station to participate
in the Link Test.
To initiate a search for a participating station, write the
broadcast address (FF-FF-FF-FF-FF-FF) to this variable.
|
| etsysDot11ExtLTRemoteStationName |
.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.2 |
|
The wireless station name of the remote station
participating in the Link Test.
|
| etsysDot11ExtLTTrigger |
.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.3 |
|
Writing a 1 to this variable causes a single Link Test
request message to be sent to the remote station.
|
| etsysDot11ExtLTRemoteContents |
.1.3.6.1.4.1.5624.1.2.9.1.1.1.1.4 |
|
The exact byte-by-byte contents of the Link Test packet returned by
the remote station.
|
| etsysDot11ExtPCCardType |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.1 |
|
The type of PC card inserted in the Access Point.
|
| etsysDot11ExtPCCardVersions |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.2 |
|
Specifies the version identifiers for the PC card.
This will indicate both the Hardware and the Firmware
versions.
|
| etsysDot11ExtBridgeMode |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.3 |
|
CURRENT Access Point bridge mode state.
In workgroup mode all communications between clients
passes through the Access Point.
LAN-to-LAN mode is the improved name for 802.11.
LAN-to-LAN used to be called full-bridge pre-802.11.
This mode is a method of connecting two wired LAN's
via a wireless link, also referred to as Point-to-Point
mode.
LAN-to-LAN-HUB mode allows the interconnection of multiple
(ie. more than two) wired LAN's via wireless links, also
referred to as Point-to-MultiPoint mode.
When operating in multimode the Access Point can simultaneously
operate in both workgroup mode and either Point-to-Point or
Point-to-MultiPoint modes.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtResetOptions |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.4 |
|
noReset (0)
No reset is performed. A 'get' on this object always returns
this value.
resetRadioCardIfNecessary (1)
Some parameters can only be given to the card at initialization
time, and if any of these are changed, a card reset will be
necessary for them to go into place. The card will be reset at
this time if any of those parameters have indeed been changed.
resetRadioCardRegardless (2)
Forces the radio card to reset, even if no radio card
parameters have been changed.
|
| etsysDot11ExtSystemScale |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.5 |
|
Specifies the CURRENT Access Point density in the
Extended Service Set (ESS).
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtSecureAccess |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.6 |
|
When this mode is set to enabled, the AP will only associate
with stations that have the same network name as the AP.
When this mode is set to disabled, a station with the
network name of ANY is allowed to associate.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtMulticastTxRate |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.7 |
|
This value specifies the Multicast data transmission
rate of the AP. It is implemented when cards that operate
faster than the 2Mbit 802.11 standard are inserted.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtIntraBSSRelay |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.8 |
|
When this mode is enabled the AP entity within the PC Card will
relay frames to destined for stations associated with it and will NOT
forward them to the bridging entity within the AP.
When this mode is set to disabled, the AP entity within the PC Card
will not relay frames from wireless client(s) to station(s) associated with it,
instead forwards frames to the bridging entity within the AP.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtStationName |
.1.3.6.1.4.1.5624.1.2.9.1.2.1.1.9 |
|
DURABLE:
The wireless station name sent out as part of
the beacon messages. Valid only when a DS card
is inserted in the Access Point.
|
| etsysDot11ExtBldgRemoteMAC1 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.1 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgRemoteMAC2 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.2 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgRemoteMAC3 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.3 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgRemoteMAC4 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.4 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgRemoteMAC5 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.5 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgRemoteMAC6 |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.6 |
|
The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtBldgMPActivationKey |
.1.3.6.1.4.1.5624.1.2.9.1.3.1.1.7 |
|
Point-to-multipoint bridge mode requires an activation
key to enable. A valid multipoint activation key must
be entered as a string of ACSCII characters translating
to the binary HEX value of the key before the Access Point
will accept the point-to-multipoint bridge mode setting.
Returns SNMP_BAD_VALUE if validation fails.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtWEPKeyDefined |
.1.3.6.1.4.1.5624.1.2.9.1.4.1.1.1 |
|
The state column used for determining if an
encryption key is set (true) or not (false),
false is the default value.
|
| etsysDot11ExtWEPKeyValue |
.1.3.6.1.4.1.5624.1.2.9.1.4.1.1.2 |
|
A WEP default secret key value. For 40-bit encryption
use 5 printable characters or 10 HEX digits. For 128-bit
encryption use 13 printable characters or 26 HEX digits.
This object must be saved across a system reset and/or a
power cycle.
|
| etsysDot11ExtWEPEnhancedImplemented |
.1.3.6.1.4.1.5624.1.2.9.1.4.2.1.1 |
|
This value indicates whether the AP is capable of Enhanced
Wireless Equivalent Privacy (WEP), using 128-bit keys.
|
| etsysDot11ExtOIDIndex |
.1.3.6.1.4.1.5624.1.2.9.1.5.1.1.1 |
|
This object will keep a list of OIDS
|
| etsysDot11ExtOIDNotInEffect |
.1.3.6.1.4.1.5624.1.2.9.1.5.1.1.2 |
|
This object specifies if the OID being accesed currently
has been changed but is not in effect.
|
| etsysDot11ExtLinkTestTable |
.1.3.6.1.4.1.5624.1.2.9.1.1.1 |
|
This table contains objects to test the link between a
requester (entity which sends out the management request
message) and a responder (entity which responds with
the appropriate management response message). An entity
could be either an Access Point(AP) or a station (STA).
|
| etsysDot11ExtGeneralTable |
.1.3.6.1.4.1.5624.1.2.9.1.2.1 |
|
This table contains all the objects that must be
configured on every radio card installed in the
Access Point regardless of the operating mode in use.
|
| etsysDot11ExtBldgTable |
.1.3.6.1.4.1.5624.1.2.9.1.3.1 |
|
This table contains the objects required to enable
the Access Point to operate in Point-to-MultiPoint mode.
|
| etsysDot11ExtWEPDefaultKeysTable |
.1.3.6.1.4.1.5624.1.2.9.1.4.1 |
|
Conceptual table for WEP default keys. This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values. The WEP
default secret keys are logically WRITE-ONLY. Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP
default key shall be null.
|
| etsysDot11ExtWEPEnhancedTable |
.1.3.6.1.4.1.5624.1.2.9.1.4.2 |
|
Conceptual table for WEP default keys. This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values. The WEP
default secret keys are logically WRITE-ONLY. Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP
default key shall be null.
|
| etsysDot11ExtOIDNotInEffectTable |
.1.3.6.1.4.1.5624.1.2.9.1.5.1 |
|
This table will be used to determine which wireless
parameters have been modified but are not yet in effect.
These parameters will not take effect until a reset has been
performed.
|
