| trkAtmIndex |
.1.3.6.1.4.1.562.2.4.1.60.3.1.1.10 |
|
This variable represents the index for the trkAtm tables.
|
| trkAtmRowStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.1.1.1 |
|
This variable is used as the basis for SNMP naming of
trkAtm components.
These components can be added and deleted.
|
| trkAtmComponentName |
.1.3.6.1.4.1.562.2.4.1.60.3.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| trkAtmStorageType |
.1.3.6.1.4.1.562.2.4.1.60.3.1.1.4 |
|
This variable represents the storage type value for the
trkAtm tables.
|
| trkAtmMaximumErroredInterval |
.1.3.6.1.4.1.562.2.4.1.60.3.10.1.1 |
|
This attribute specifies the interval time over which the error
threshold (as specified by receiveErrorSensitivity) must be
continuously exceeded before the Unacknowledged, Utp,
AtmAccess or FrAccess component can be degraded. Once the error
interval count exceeds the provisioned value, the Unacknowledged,
Utp, AtmAccess or FrAccess component will issue an alarm
indicating that link quality has degraded, and it will also disable its
parent component. The exception to this is a value of zero, the
default, which indicates that the mechanism is completely disabled.
|
| trkAtmReceiveErrorSensitivity |
.1.3.6.1.4.1.562.2.4.1.60.3.10.1.2 |
|
This attribute specifies the allowable error rate beyond which the
AtmAccess component can be degraded if the error rate persists for
a duration longer than the maximumErrorInterval. The threshold is
expressed as a percentage. It is the ratio of the number of errored
cells in the last interval over the number of cells received in the last
interval. For AAL5, the number of errored cells is converted from
rxFrameDiscard of AtmIf Vcc using the assumption that three ATM
cells are used to carry a 128 byte AAL5 frame. The number of
received cells is specified by rxCell of AtmIf Vcc.
The configurable values are:
0 = the mechanism is completely disabled
1 = 1/(2**1)
2 = 1/(2**2)
3 = 1/(2**3)
:
10 = 1/(2**10)
|
| trkAtmAtmAccMaximumErroredInterval |
.1.3.6.1.4.1.562.2.4.1.60.3.10.1.3 |
|
This attribute specifies the interval time over which the error
threshold (as specified by receiveErrorSensitivity) must be
continuously exceeded before the AtmAccess component can be
degraded. Once the error interval count exceeds the provisioned
value, the AtmAccess component issues an alarm indicating that link
quality has degraded, and it disables its parent component. The
exception to this is a value of zero, the default, which indicates that
the mechanism is completely disabled.
|
| trkAtmAtmConnection |
.1.3.6.1.4.1.562.2.4.1.60.3.11.1.1 |
|
This attribute specifies the component name of the ATM Layer 2
AAL5 interface that the AtmAccess component will use.
|
| trkAtmBwElastic |
.1.3.6.1.4.1.562.2.4.1.60.3.11.1.2 |
|
This attribute specifies how changes in the bandwidth of the
atmConnection are handled by the ATM software. If its value is no,
the atmConnection will be released by the ATM software if it is
incapable of providing the bandwidth specified by the peak cell rate
(PCR) defined in txTrafficDescParm of AtmIf Vcc Vcd. If the value
is yes, the atmConnection is not released in this situation, but its
bandwidth may be reduced. Also, if this value is yes, the Dynamic
Speed Reporting mechanism must be enabled, by provisioning at
least one value in the speedReportingThresholds attribute of the
parent Trunk component.
|
| trkAtmVccReportingBw |
.1.3.6.1.4.1.562.2.4.1.60.3.11.1.3 |
|
This attribute specifies how the bandwidth of the VCC is reported to
the parent Trunk component. If its value is pcr and attribute
bwElastic of AtmAccess has a value of no, the peak cell rate (PCR)
of the VCC, defined in txTrafficDescParm of AtmIf Vcc Vcd, is
reported. If its value is pcr and attribute bwElastic of AtmAccess has
a value of yes, the minimum of the PCR, defined in
txTrafficDescParm of AtmIf Vcc Vcd, and the current cell rate
(CCR) of the VCC is reported. If its value is acr, the best
measurement of the actual cell rate (ACR) of the VCC is reported,
which is the minimum of the PCR, the CCR and the actual shaping
rate (ASR). The value of the reported bandwidth of the VCC is
indicated by the measuredSpeedToIf attribute of the parent Trunk
component.
|
| trkAtmAdminState |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.1 |
|
This attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| trkAtmOperationalState |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.2 |
|
This attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| trkAtmUsageState |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.3 |
|
This attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| trkAtmAvailabilityStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.4 |
|
If supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)
|
| trkAtmProceduralStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.5 |
|
If supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)
|
| trkAtmControlStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.6 |
|
If supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)
|
| trkAtmAlarmStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.7 |
|
If supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)
|
| trkAtmStandbyStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.8 |
|
If supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.
|
| trkAtmUnknownStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.12.1.9 |
|
This attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.
|
| trkAtmMinorVccUtilAlarmThreshold |
.1.3.6.1.4.1.562.2.4.1.60.3.14.1.1 |
|
This attribute specifies the threshold value at which a minor alarm
will be issued based on a sustained average ATM VCC utilization as
indicated by the lastCalculatedVccUtilization attribute. The Set
alarm is issued after 3 minutes of utilization greater than the
threshold. The corresponding Clear alarm is issued after a
subsequent 3 minutes of utilization less than or equal to the
threshold.
The value 200% is used to disable this threshold. For values other
than 200%, the minor alarm threshold must be less than the other
thresholds.
|
| trkAtmMajorVccUtilAlarmThreshold |
.1.3.6.1.4.1.562.2.4.1.60.3.14.1.2 |
|
This attribute specifies the threshold value at which a major alarm
will be issued based on a sustained average ATM VCC utilization as
indicated by the lastCalculatedVccUtilization attribute. The Set
alarm is issued after 3 minutes of utilization greater than the
threshold. The corresponding Clear alarm is issued after a
subsequent 3 minutes of utilization less than or equal to the
threshold.
The value 200% is used to disable this threshold. For values other
than 200%, the major alarm threshold must be greater than the
minor threshold and less than the critical threshold.
|
| trkAtmCriticalVccUtilAlarmThreshold |
.1.3.6.1.4.1.562.2.4.1.60.3.14.1.3 |
|
This attribute specifies the threshold value at which a critical alarm
will be issued based on a sustained average ATM VCC utilization as
indicated by the lastCalculatedVccUtilization attribute. The Set
alarm is issued after 3 minutes of utilization greater than the
threshold. The corresponding Clear alarm is issued after a
subsequent 3 minutes of utilization less than or equal to the
threshold.
The value 200% is used to disable this threshold. For values other
than 200%, the critical alarm threshold must be greater than the
other thresholds.
|
| trkAtmVccUtilAlarmStatus |
.1.3.6.1.4.1.562.2.4.1.60.3.14.1.4 |
|
This attribute provides control of the generation of ATM VCC
utilization alarms. If the value is disabled, none of the alarms is
generated (this is equivalent to setting all of the thresholds to
200%). If the value is enabled, the individual thresholds are
handled.
|
| trkAtmLastCalculatedVccUtilization |
.1.3.6.1.4.1.562.2.4.1.60.3.15.1.1 |
|
This attribute indicates the last calculated receive utilization of the
ATM VCC. It is calculated every 30 seconds based on comparing
the number of cells received by the AtmIf Vcc with the estimated
available bandwidth on the AtmIf Vcc.
|
| trkAtmLastCalculatedTxVccUtilization |
.1.3.6.1.4.1.562.2.4.1.60.3.15.1.2 |
|
This attribute indicates the last calculated transmit utilization of the
ATM VCC. It is calculated every 30 seconds based on comparing
the number of cells transmitted by the AtmIf Vcc with the estimated
available bandwidth on the AtmIf Vcc.
|
