| mcsMgrDprsMcsEpGIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpG tables.
|
| mcsMgrDprsMcsEpGRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpG components.
These components can be added and deleted.
|
| mcsMgrDprsMcsEpGComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpG tables.
|
| mcsMgrDprsMcsEpGRemoteAddress |
.1.3.6.1.4.1.562.2.4.1.122.2.10.1.1 |
|
This attribute indicates the NSAP address of the McsMgr at the
destination module to which all EndPoints of this group are
connected.
|
| mcsMgrDprsMcsEpGAssociatedEpGroupName |
.1.3.6.1.4.1.562.2.4.1.122.2.10.1.2 |
|
For a provisioned DprsMcsEpG, this attribute indicates the name of
the DprsMcsEpG that contains the dynamic Eps to the same
destination.
For a dynamic DprsMcsEpG, this attribute indicates the name of the
DprsMcsEpG that contains the provisioned Eps to the same
destination.
A null component name indicates that there is no DprsMcsEpG
associated with this group.
|
| mcsMgrDprsMcsEpGAddrIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.2.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpGAddr tables.
|
| mcsMgrDprsMcsEpGAddrRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpGAddr components.
These components cannot be added nor deleted.
|
| mcsMgrDprsMcsEpGAddrComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGAddrStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.2.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpGAddr tables.
|
| mcsMgrDprsMcsEpGAddrRemoteAddress |
.1.3.6.1.4.1.562.2.4.1.122.2.2.10.1.1 |
|
This attribute specifies the NSAP address of the McsMgr at the
destination module. This address is used by the EndPoints
provisioned under this DprsMcsEpG to establish a Dprs MCS
Switched Path.
|
| mcsMgrDprsMcsEpGAddrCommentText |
.1.3.6.1.4.1.562.2.4.1.122.2.2.10.1.2 |
|
This attribute specifies additional textual information to be added by
the network operator. Typical use of this attribute is to specify the
destination module name.
|
| mcsMgrDprsMcsEpGEpIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpGEp tables.
|
| mcsMgrDprsMcsEpGEpRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpGEp components.
These components can be added and deleted.
|
| mcsMgrDprsMcsEpGEpComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGEpStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpGEp tables.
|
| mcsMgrDprsMcsEpGEpAdminState |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.1 |
|
This attribute indicates the OSI Administrative State of the
component.
The value locked indicates that the component is administratively
prohibited from providing services for its users. A Lock or Lock -
force command has been previously issued for this component.
When the value is locked, the value of usageState must be idle.
The value shuttingDown indicates that the component is
administratively permitted to provide service to its existing users
only. A Lock command was issued against the component and it is
in the process of shutting down.
The value unlocked indicates that the component is administratively
permitted to provide services for its users. To enter this state, issue
an Unlock command to this component.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| mcsMgrDprsMcsEpGEpOperationalState |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.2 |
|
This attribute indicates the OSI Operational State of the component.
The value enabled indicates that the component is available for
operation. Note that if adminState is locked, it would still not be
providing service.
The value disabled indicates that the component is not available for
operation. For example, something is wrong with the component
itself, or with another component on which this one depends. If the
value is disabled, the usageState must be idle.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| mcsMgrDprsMcsEpGEpUsageState |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.3 |
|
This attribute indicates the OSI Usage State of the component.
The value idle indicates that the component is not currently in use.
The value active indicates that the component is in use and has
spare capacity to provide for additional users.
The value busy indicates that the component is in use and has no
spare operating capacity for additional users at this time.
The OSI Status attributes, if supported by the component, may
provide more details, qualifying the state of the component.
|
| mcsMgrDprsMcsEpGEpAvailabilityStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.4 |
|
If supported by the component, this attribute indicates the OSI
Availability status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value inTest indicates that the resource is undergoing a test
procedure. If adminState is locked or shuttingDown, the normal
users are precluded from using the resource and controlStatus is
reservedForTest. Tests that do not exclude additional users can be
present in any operational or administrative state but the
reservedForTest condition should not be present.
The value failed indicates that the component has an internal fault
that prevents it from operating. The operationalState is disabled.
The value dependency indicates that the component cannot operate
because some other resource on which it depends is unavailable.
The operationalState is disabled.
The value powerOff indicates the resource requires power to be
applied and it is not powered on. The operationalState is disabled.
The value offLine indicates the resource requires a routine
operation (either manual, automatic, or both) to be performed to
place it on-line and make it available for use. The operationalState
is disabled.
The value offDuty indicates the resource is inactive in accordance
with a predetermined time schedule. In the absence of other
disabling conditions, the operationalState is enabled or disabled.
The value degraded indicates the service provided by the
component is degraded in some way, such as in speed or operating
capacity. However, the resource remains available for service. The
operationalState is enabled.
The value notInstalled indicates the resource is not present. The
operationalState is disabled.
The value logFull is not used.
Description of bits:
inTest(0)
failed(1)
powerOff(2)
offLine(3)
offDuty(4)
dependency(5)
degraded(6)
notInstalled(7)
logFull(8)
|
| mcsMgrDprsMcsEpGEpProceduralStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.5 |
|
If supported by the component, this attribute indicates the OSI
Procedural status of the component. Note that, even though it is
defined as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value initializationRequired indicates (for a resource which
doesn't initialize autonomously) that initialization is required before
it can perform its normal functions, and this procedure has not been
initiated. The operationalState is disabled.
The value notInitialized indicates (for a resource which does
initialize autonomously) that initialization is required before it can
perform its normal functions, and this procedure has not been
initiated. The operationalState may be enabled or disabled.
The value initializing indicates that initialization has been initiated
but is not yet complete. The operationalState may be enabled or
disabled.
The value reporting indicates the resource has completed some
processing operation and is notifying the results. The
operationalState is enabled.
The value terminating indicates the component is in a termination
phase. If the resource doesn't reinitialize autonomously,
operationalState is disabled; otherwise it is enabled or disabled.
Description of bits:
initializationRequired(0)
notInitialized(1)
initializing(2)
reporting(3)
terminating(4)
|
| mcsMgrDprsMcsEpGEpControlStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.6 |
|
If supported by the component, this attribute indicates the OSI
Control status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value subjectToTest indicates the resource is available but tests
may be conducted simultaneously at unpredictable times, which
may cause it to exhibit unusual characteristics.
The value partOfServicesLocked indicates that part of the service is
restricted from users of a resource. The adminState is unlocked.
The value reservedForTest indicates that the component is
administratively unavailable because it is undergoing a test
procedure. The adminState is locked.
The value suspended indicates that the service has been
administratively suspended.
Description of bits:
subjectToTest(0)
partOfServicesLocked(1)
reservedForTest(2)
suspended(3)
|
| mcsMgrDprsMcsEpGEpAlarmStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.7 |
|
If supported by the component, this attribute indicates the OSI
Alarm status of the component. Note that, even though it is defined
as a multi-valued set, at most one value is shown to the user.
When no values are in the set, this indicates that either the attribute
is not supported or that none of the status conditions described
below are present.
The value underRepair indicates the component is currently being
repaired. The operationalState is enabled or disabled.
The value critical indicates one or more critical alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value major indicates one or more major alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value minor indicates one or more minor alarms are
outstanding against the component. Other, less severe, alarms may
also be outstanding. The operationalState is enabled or disabled.
The value alarmOutstanding generically indicates that an alarm of
some severity is outstanding against the component.
Description of bits:
underRepair(0)
critical(1)
major(2)
minor(3)
alarmOutstanding(4)
|
| mcsMgrDprsMcsEpGEpStandbyStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.8 |
|
If supported by the component, this attribute indicates the OSI
Standby status of the component.
The value notSet indicates that either the attribute is not supported
or that none of the status conditions described below are present.
Note that this is a non-standard value, used because the original
specification indicated this attribute was set-valued and thus, did not
provide a value to indicate that none of the other three are
applicable.
The value hotStandby indicates that the resource is not providing
service but will be immediately able to take over the role of the
resource to be backed up, without initialization activity, and
containing the same information as the resource to be backed up.
The value coldStandby indicates the resource is a backup for
another resource but will not be immediately able to take over the
role of the backed up resource and will require some initialization
activity.
The value providingService indicates that this component, as a
backup resource, is currently backing up another resource.
|
| mcsMgrDprsMcsEpGEpUnknownStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.10.1.9 |
|
This attribute indicates the OSI Unknown status of the component.
The value false indicates that all of the other OSI State and Status
attribute values can be considered accurate.
The value true indicates that the actual state of the component is not
known for sure.
|
| mcsMgrDprsMcsEpGEpLastTransportConnectionClearCause |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.3 |
|
This attribute indicates the most recent clear cause for the transport
connection.
This indicates the causes provided by the network.
A value of zero indicates that the transport connection has never
been cleared.
A value of 1000 indicates that the network has not provided a clear
cause for the transport connection clearing.
Section 5.4.5.15 of the ATMF UNI 3.1 specification lists the clear
causes provided by the network.
|
| mcsMgrDprsMcsEpGEpType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.4 |
|
This attribute indicates the type of the end point. If the value is
originating, this Ep is provisioned and is responsible for initiating
the SPVC call to set up the PORS or ATM connection. If the value
is terminating, this Ep is created dynamically by the McsMgr at the
destination node when it receives a call setup request.
|
| mcsMgrDprsMcsEpGEpSupportedTransferPriorities |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.5 |
|
This attribute indicates the Frame Relay transfer priorities
supported by the transport connection.
Description of bits:
n0(0)
n1(1)
n2(2)
n3(3)
n4(4)
n5(5)
n6(6)
n7(7)
n8(8)
n9(9)
n10(10)
n11(11)
n12(12)
n13(13)
n14(14)
n15(15)
|
| mcsMgrDprsMcsEpGEpConnectionTransferPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.6 |
|
This attribute indicates the transfer priority used to establish the
transport connection.
|
| mcsMgrDprsMcsEpGEpServiceCategory |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.7 |
|
This attribute indicates the ATM service category of the transport
connection.
|
| mcsMgrDprsMcsEpGEpBandwidth |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.8 |
|
This attribute indicates the bandwidth at which the transport
connection agrees to transfer information.
|
| mcsMgrDprsMcsEpGEpRemoteComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.9 |
|
This attribute indicates the component name of the remote Ep,
learned from the remote end.
For example: 'EM/NODEY2D0 McsMgr DprsMcsEpG/1 Ep/1'.
The value will be a null string if the transport connection is down.
|
| mcsMgrDprsMcsEpGEpRemoteRoutingId |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.10 |
|
This attribute indicates the routing identifier (RID) associated with
the Passport node on which the remote Ep resides. The remote RID
is learned from the remote Ep.
The value is valid when the transport connection is up and zero
otherwise.
|
| mcsMgrDprsMcsEpGEpRemoteModuleId |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.11 |
|
This attribute indicates the module identifier (MID) associated with
the Passport node on which the remote Ep resides. The remote MID
is learned from the remote Ep.
The value is valid when the transport connection is up and zero
otherwise.
|
| mcsMgrDprsMcsEpGEpLastTrConnDiagCode |
.1.3.6.1.4.1.562.2.4.1.122.2.3.11.1.12 |
|
This attribute indicates the diagnostic code of the most recently
cleared transport connection.
This indicates the diagnostic code (associated with the
lastTransportConnectionClearCause) provided by the network.
A string containing only a 0 or 00 (zero) indicates that the network
has not provided a diagnostic code for the most recently cleared
transport connection.
Section 5.4.5.15 of the ATMF UNI 3.1 specification lists the
diagnostic codes that can be provided by the network.
|
| mcsMgrDprsMcsEpGEpSetupAttempts |
.1.3.6.1.4.1.562.2.4.1.122.2.3.12.1.1 |
|
This attribute counts the number of attempts made to set up the
transport connection. The counter wraps around to zero when the
maximum value is reached.
|
| mcsMgrDprsMcsEpGEpPktDiscErroredFromMcs |
.1.3.6.1.4.1.562.2.4.1.122.2.3.12.1.2 |
|
This attribute counts errored packets received on the Dprs MCS
Switched Path that have been discarded.
The counter wraps around to zero when the maximum value is
reached.
|
| mcsMgrDprsMcsEpGEpPktFromMcsIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.402.1.1 |
|
This variable represents the mcsMgrDprsMcsEpGEpPktFromMcsTable
specific index for the mcsMgrDprsMcsEpGEpPktFromMcsTable.
|
| mcsMgrDprsMcsEpGEpPktFromMcsValue |
.1.3.6.1.4.1.562.2.4.1.122.2.3.402.1.2 |
|
This variable represents an individual value for the
mcsMgrDprsMcsEpGEpPktFromMcsTable.
|
| mcsMgrDprsMcsEpGEpOctetsFromMcsIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.403.1.1 |
|
This variable represents the mcsMgrDprsMcsEpGEpOctetsFromMcsTable
specific index for the mcsMgrDprsMcsEpGEpOctetsFromMcsTable.
|
| mcsMgrDprsMcsEpGEpOctetsFromMcsValue |
.1.3.6.1.4.1.562.2.4.1.122.2.3.403.1.2 |
|
This variable represents an individual value for the
mcsMgrDprsMcsEpGEpOctetsFromMcsTable.
|
| mcsMgrDprsMcsEpGEpPktDiscCongestedFromMcsIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.404.1.1 |
|
This variable represents the mcsMgrDprsMcsEpGEpPktDiscCongestedFromMcsTable
specific index for the mcsMgrDprsMcsEpGEpPktDiscCongestedFromMcsTable.
|
| mcsMgrDprsMcsEpGEpPktDiscCongestedFromMcsValue |
.1.3.6.1.4.1.562.2.4.1.122.2.3.404.1.2 |
|
This variable represents an individual value for the
mcsMgrDprsMcsEpGEpPktDiscCongestedFromMcsTable.
|
| mcsMgrDprsMcsEpGEpEpDIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpGEpEpD tables.
|
| mcsMgrDprsMcsEpGEpEpDRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpGEpEpD components.
These components cannot be added nor deleted.
|
| mcsMgrDprsMcsEpGEpEpDComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGEpEpDStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpGEpEpD tables.
|
| mcsMgrDprsMcsEpGEpEpDBandwidth |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.1 |
|
This attribute specifies the bandwidth at which the transport
connection agrees to transfer information.
A conservative value would be the sum of the committed
information rates (CIRs) of all individual Frame Relay DLCIs
multiplexed on the transport connection.
For ATM connections, the value is converted to an equivalent Peak
Cell Rate (PCR01) for all cells with Cell Loss Priority (CLP), CLP
= 0 and CLP = 1.
Note that the conversion to an equivalent cell rate for ATM
connections may result in some wasted bandwidth depending on the
average frame size to cell ratio.
|
| mcsMgrDprsMcsEpGEpEpDConnectionTransferPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.2 |
|
This attribute specifies the transfer priority used to establish the
transport connection. It references the ModuleData Frs AtmNet Tpm
to determine the ATM service category to be used by the transport
connection.
This attribute is used by the Ep solely for the purpose of
determining the service category that should be used to establish the
transport connection.
|
| mcsMgrDprsMcsEpGEpEpDTransportConnectionPreference |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.3 |
|
This attribute specifies the preference of routing system to be used
to set up the transport connection.
If a value of atmOnly is specified, attempts to set up the transport
connection will be made using only the ATM routing system's
network facilities.
If a value of porsOnly is specified, attempts to set up the transport
connection will be made using only PORS network facilities.
|
| mcsMgrDprsMcsEpGEpEpDProfile |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.4 |
|
This attribute specifies the PORS profile to be used for the transport
connection when it is set up using PORS. This attribute is ignored if
the transportConnectionPreference is atmOnly.
|
| mcsMgrDprsMcsEpGEpEpDPorsManualPath |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.5 |
|
This attribute specifies the PORS manual path to be used for the
transport connection when it is set up using PORS. The manual path
that this attribute is linked to specifies the sequence of Trunks that
will be used when PORS chooses and instantiates the route.
This attribute is ignored if the transportConnectionPreference is
atmOnly.
|
| mcsMgrDprsMcsEpGEpEpDSupportedTransferPriorities |
.1.3.6.1.4.1.562.2.4.1.122.2.3.2.10.1.6 |
|
This attribute specifies the Frame Relay transfer priorities that are
supported through the transport connection. It is used to determine
which EndPoint within a DprsMcsEndPointGroup is to multiplex a
particular Frame Relay DLCI.
A particular transfer priority can be specified on at most one
EndPoint within a DprsMcsEndPointGroup.
Description of bits:
n0(0)
n1(1)
n2(2)
n3(3)
n4(4)
n5(5)
n6(6)
n7(7)
n8(8)
n9(9)
n10(10)
n11(11)
n12(12)
n13(13)
n14(14)
n15(15)
|
| mcsMgrDprsMcsEpGEpAtmConIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.3.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpGEpAtmCon tables.
|
| mcsMgrDprsMcsEpGEpAtmConRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.3.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpGEpAtmCon components.
These components cannot be added nor deleted.
|
| mcsMgrDprsMcsEpGEpAtmConComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.3.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGEpAtmConStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.3.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpGEpAtmCon tables.
|
| mcsMgrDprsMcsEpGEpAtmConNextHop |
.1.3.6.1.4.1.562.2.4.1.122.2.3.3.10.1.1 |
|
This attribute shows the component name of the AtmIf Vcc Ep or
AtmCon component to which this switched connection is
established.
|
| mcsMgrDprsMcsEpGEpLCoIndex |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.1.1.10 |
|
This variable represents the index for the mcsMgrDprsMcsEpGEpLCo tables.
|
| mcsMgrDprsMcsEpGEpLCoRowStatus |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.1.1.1 |
|
This variable is used as the basis for SNMP naming of
mcsMgrDprsMcsEpGEpLCo components.
These components cannot be added nor deleted.
|
| mcsMgrDprsMcsEpGEpLCoComponentName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| mcsMgrDprsMcsEpGEpLCoStorageType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.1.1.4 |
|
This variable represents the storage type value for the
mcsMgrDprsMcsEpGEpLCo tables.
|
| mcsMgrDprsMcsEpGEpLCoState |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.1 |
|
This attribute reflects the current state of the connection. The
pathDown state indicates a connection that has no remote end
provisioned or the application has not yet signalled for a path. The
selectingRoute state occurs when a request has been sent to route
selector and it has not yet responded. The connectingState occurs
while a path is being established. The pathUp state is the normal
operational state of a path. The pathDownRetrying state indicates a
path that attempted route selection but received no route and is now
waiting to retry route selection again.
|
| mcsMgrDprsMcsEpGEpLCoOverrideRemoteName |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.2 |
|
If set and the current PLC remoteName is blank this remoteName
will override the blank PLC remoteName. Usually you would set
this attribute and then lock/unlock the service component which
will result in this new overrideRemoteName being used as if it had
been provisioned into the PLC remoteName. The advantage of this
attribute is that the connection's remoteName can be changed
immediately without having to 'activate prov' but the disadvantage
is that the overrideRemoteName is not permanent and if the card or
switch is reset the override will be lost.
|
| mcsMgrDprsMcsEpGEpLCoEnd |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.3 |
|
This attribute identifies whether this is the calling or called end of
the path.
|
| mcsMgrDprsMcsEpGEpLCoCostMetric |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.4 |
|
This attribute gives the route's total cost metric. It is calculated as
the sum of the cost metric of all trunks in the path at the time the
connection was established. The cost metric of a trunk is defined by
the trunkCost attribute of the Trunk component. The costMetric for
an LCo that is originated and terminated on the same module is 0.
|
| mcsMgrDprsMcsEpGEpLCoDelayMetric |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.5 |
|
This attribute gives the total delay of the route as the one way delay
for a 512 byte packet. It is calculated as the sum of the delays of all
trunks in the path stored in topology at the time the connection was
established. The delay for an LCo that is originated and terminated
on the same module is 0.
|
| mcsMgrDprsMcsEpGEpLCoRoundTripDelay |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.6 |
|
This attribute contains the time taken for a packet (cell) of 44 bytes
to be transmitted to the remote LCo and return to this LCo. The
number reported is given in milliseconds to the nearest millisecond.
A value of one millisecond is reported if the time is less than 1
millisecond even though the delay may be less than 1 Millisecond
when the LCo is originated and terminated on the same module.
|
| mcsMgrDprsMcsEpGEpLCoSetupPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.7 |
|
This attribute gives the priority at which the current path is
established. Zero is the highest priority and four is the lowest. The
holdingPriority, a complementary attribute of this component,
indicates the priority a path maintains once it is established.
|
| mcsMgrDprsMcsEpGEpLCoHoldingPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.8 |
|
This attribute gives the priority at which a path holds its current
path once the path is established. Zero is the highest priority and
four is the lowest. The setupPriority, a complementary attribute,
indicates the priority of a path at establishment time.
|
| mcsMgrDprsMcsEpGEpLCoRequiredTxBandwidth |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.9 |
|
This attribute gives the actual bandwidth (in bits per second)
reserved by this path on each of the trunks of its route. This attribute
represents the bandwidth for traffic outgoing to the remote end
point. The originating end of the connection determines this value.
|
| mcsMgrDprsMcsEpGEpLCoRequiredRxBandwidth |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.10 |
|
This attribute gives the actual bandwidth (in bits per second)
reserved by this path on each of trunks of its route. This attribute
represents the bandwidth for traffic incoming from the remote end
point. The originating end of the connection determines this value
|
| mcsMgrDprsMcsEpGEpLCoRequiredTrafficType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.11 |
|
This operational attribute indicates the type of traffic transmitted
over the path. There are eight possible traffic types, and the path can
transmit only one of them. The originating end of the connection
determines the type. These are arbitrary designations for traffic
type. The voice, data and video traffic types are defined, and five
other arbitrary traffic types can be defined by the network
administration. This attribute is used in the route selection process
to restrict the route to trunks that support this traffic type. The
supportedTrafficType trunk attribute lists all the types of traffic
allowed on the trunk. For example, if requiredTrafficType is
specified as trafficType1 then only trunks that include trafficType1
in supportedTrafficType, will be candidates for this connection.
|
| mcsMgrDprsMcsEpGEpLCoPermittedTrunkTypes |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.12 |
|
This operational attribute lists up to eight types of trunk that can be
used on the route. The originating end of the connection determines
the types. The terrestrial and satellite trunk types have been
defined, leaving six remaining arbitrary types that can be defined by
the network administration. The trunk's type is indicated in the
trunkType attribute of the Trunk component. When selecting a
route, PORS only chooses trunks whose trunkType are in the
permittedTrunkTypes for the path.
Description of bits:
terrestrial(0)
satellite(1)
trunkType1(2)
trunkType2(3)
trunkType3(4)
trunkType4(5)
trunkType5(6)
trunkType6(7)
|
| mcsMgrDprsMcsEpGEpLCoRequiredSecurity |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.13 |
|
This attribute indicates the required minimum level of security of
the trunks on the route. Zero represents the most secure and seven
represents the least secure. The trunk's security is indicated by the
trunkSecurity attribute of the Trunk component, and has values
identical in range and meaning to the requiredSecurity attribute.
PORS ensures that any route selected does not contain a trunk
whose trunkSecurity attribute is numerically greater than the
requiredSecurity.
|
| mcsMgrDprsMcsEpGEpLCoRequiredCustomerParameter |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.14 |
|
This attribute indicates the allowed customer defined parameter of
the trunks on the route.The originating end of the connection
determines the customer defined parameter. Its value, a number
from zero to seven, is chosen by a network administration to have a
meaning specific to their network, thus allowing them to customize
the use of their trunks. A complementary trunk attribute,
customerParameter, also has a value from zero to seven. The route
selection process does not consider trunks whose
customerParameter is greater than the requiredCustomerParameter
of the path.
|
| mcsMgrDprsMcsEpGEpLCoEmissionPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.15 |
|
This attribute indicates the urgency with which packets on the path
are emitted by the trunks on the route. The originating end of the
connection selects the emissionPriority. EmissionPriority of zero
indicates the highest emission priority, while two indicates the
lowest emission priority. Packets with a higher emissionPriority (or
numerically less) are serviced and sent out before the packets of
lower emissionPriority (or numerically higher).
|
| mcsMgrDprsMcsEpGEpLCoDiscardPriority |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.16 |
|
This attribute indicates the importance of the packets on the
path.The originating end of the connection sets discardPriority. One
is used for paths carrying the most important traffic, and three is
used for paths carrying the least important traffic. Packets with
lower discardPriority(numerically lower) are discarded after
packets with a higher discardPriority(numerically higher).
|
| mcsMgrDprsMcsEpGEpLCoPathType |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.17 |
|
This attribute indicates whether the path for this PLC was
determined automatically or by static provisioning. Normal
pathTypes are selected automatically by Route Selector.The other
pathTypes are both manual pathTypes where the operator must
specify, through provisioning, a static route termed the manualPath.
A manual pathType connection is nearly identical to a normal path
type connection with the exception that the route is pre-provisioned.
For a manual pathType, bandwidth reservations are respected along
the path exactly as in a normal path. The last type, the forced
pathType, is also a manual path but regardless of the bandwidth
available the route is granted provided the trunks are operational
and there are sufficient Logical Channels (LChs).
The forced pathType could result in over committing the reserved
bandwidth allowed on a trunk. A better way to achieve the effects of
a forced pathType is to use a manual pathType with setupPriority =
0 and holdingPriority = 0. In this manner the path will reserve
correct bandwidth and it will bump other paths if required while not
being bumped itself.
|
| mcsMgrDprsMcsEpGEpLCoRetryCount |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.18 |
|
This attribute is the count of the number of times the path chosen
during route selection could not be instantiated. This count should
be three or below if the network is performing adequately. A high
value indicates that the route selection is often performed using an
out-of-date view of available network bandwidth and/or topology.
This attribute will only increase at the calling end of the connection.
This attribute is reset each time a path reconnects and stops
counting when it reaches its maximum value.
|
| mcsMgrDprsMcsEpGEpLCoPathFailureCount |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.19 |
|
This attribute is the count of the number of times the path has
successfully connected. It is set to zero the first time the path is up.
If a path fails anytime after connecting this count will be
incremented when the path is up again. Failed route requests do not
count in this statistic. See retryCount above. This attribute stops
counting at its maximum value.
|
| mcsMgrDprsMcsEpGEpLCoReasonForNoRoute |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.20 |
|
This attribute is the route selection's reasonForNoRoute and
provides a brief reason for which a route was not selected. The
reasons are essentially self-explanatory. Perhaps two reasons for no
route require some explanation. The reason
unknownRemoteNodeName is issued when the remote node name
is not in the topological database. The reason plcAttributesNotMet
is issued when there is no network connectivity at a level specified
by the PLC attributes. This reason is also issued when there is no
physical connectivity between two end nodes.
|
| mcsMgrDprsMcsEpGEpLCoLastTearDownReason |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.21 |
|
This attribute reflects the last tear down reason for a connection
(LCo). In many cases this displays the reason for a momentary
service interruption. This attribute applies to the last path failure
only. If a path is no longer up, this may give an indication to the
reason that the path has failed. In many cases an alarm will also be
generated with more specific information. The following is a brief
description of the reasons:
none - This path has no information for the teardown this is typical
of a path provisioned with no remoteName that has not been up.
normalShutDown - This path has gone down due to normal call
termination.
insufficientTxLcOrBandwidth - At present there is either no
available bandwidth or logical channel numbers available on one or
more of the trunks for this path in the transmit direction.
insufficientRxLcOrBandwidth - At present there is either no
available bandwidth or logical channel numbers available on one or
more of the trunks for this path in the receive direction.
trunkFailure- A trunk on the path has failed or has gone down due
to a provisioning change of a critical attribute.
trunkCardFailure- A trunk FP card has failed along the path.
accessCardFailure- The FP on which the peer access service was
running has failed.
operatorForced- The path has terminated due to the operator
locking a trunk along the path.
lostLcnClash- The path has terminated because the PA's at both
ends of an intermediate trunk have allocated the same LC to
different calls. When this happens both calls must go down and then
try to come up again a fraction of a second later (effectively
ensuring that they will now be assigned different LC's). It is normal
to get the odd clash especially when the PA's usedLC is
approaching the PA's maxLC.
networkCongestion - The path has failed due to control information
being lost and not recoverable.
trunkNotFound - Occurs on a manual path usually. Check for
trunks not up or names provisioned incorrectly.
farEndNotFound - The far end is not provisioned or is not up.
Check remote Name.
wrongModuleReached - This may occur on a manual path. Check
provisioning for correct trunk and service names. For a normal
path, the network Topology may be changing check remoteName.
farEndBusy - The far end has been reached but it is busy. Check
remoteName and remote end provisioning.
callLoopedBack - This LCo is provisioned to call itself. Re-
provision since this is invalid.
unknownReason - The failure was not resolved.
farEndNotReady - The remote end was reached but the connection
was refused due to the remote end not being enabled.
remoteNameMismatch - The remote end has alarmed and rejected
this setup due to remoteName provisioning.
serviceTypeMismatch - The remote Service Type does not match
this service type. Check provisioning.
reconnectFromFarEnd - The remote end re-established this
connection. Check the remote end lastTearDownReason to
determine the real reason.
bumped - Another call bumped this path from a trunk to get
bandwidth (or an LC) which it required to come up. This other path
had a higher setupPriority than this path's holdingPriority hence it
was allowed to steal the bandwidth (or LC) from this path.
optimized - This call has been rerouted due to the optimization
feature. The call is still active this just indicates why the path
changed.
trunkOrFarEndDidNotSupportMode - This call was unable to
complete because a mode required by the service was not supported
by one of the trunks the route went through or by the far end service
it connected to. Currently the only mode that this applies to is the
map/mux mode on TRUNK PA ATM component. Map mode was
required by the application (CES/FrAtm etc.) but was not available
on the TRUNK PA ATM component through which the call was
routed or the far end CES/FrAtm component did not specify the
same mode.
|
| mcsMgrDprsMcsEpGEpLCoPathFailureAction |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.22 |
|
This attribute displays whether the application is set to tolerate
momentary interruption of a path while a new path is selected. If
disconnectConnection is displayed, the application is informed as
soon as possible about a failure by disconnection. If the attribute
displays reRoutePath, the path may attempt an immediate reroute,
provided the failure is a recoverable failure. If rerouting fails the
application is informed of the failure.
With this option set to reRoutePath the LCo may wait up to 30
seconds before informing the service of complete disconnection in
order to allow both ends to attempt to reconnect. Note that if PLC
components are different at both ends only the calling end is
allowed to reconnect.
All pathTypes respect this attribute. Also on a manualPath with
both ends provisioned with independent paths (at least with respect
to the failure) this option will have the desired effect that the path is
rerouted without complete disconnection at both ends
|
| mcsMgrDprsMcsEpGEpLCoBumpPreference |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.23 |
|
This attribute specifies when bumping will occur during route
selection process. Bumping may occur when necessary or always. It
will be necessary for a connection to bump if there is not enough
resources for the connection to be established and these resources
are occupied by a connection whose setupPriority is lower
(numerically higher) than the connection's setupPriority. A
connection may also always bump in order to obtain the best route.
|
| mcsMgrDprsMcsEpGEpLCoOptimization |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.24 |
|
This attribute is used to specify whether this connection should
attempt to optimize its path when requested by the routing PORS
component. Every path is as optimal as it can be when it is
established, but as network traffic patterns and configurations
change this path may no longer be as optimal as it could be. The
PORS connection manager on a module requests circuits to
optimize at the optimization interval.
|
| mcsMgrDprsMcsEpGEpLCoPathUpDateTime |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.10.1.25 |
|
This is the time stamp when the current path was established or
reestablished.
|
| mcsMgrDprsMcsEpGEpLCoPktsToNetwork |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.11.1.1 |
|
This attribute counts the number of packets transmitted to the
network over this Logical Connection.
|
| mcsMgrDprsMcsEpGEpLCoBytesToNetwork |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.11.1.2 |
|
This attribute counts the number of bytes sent to the network over
this Logical Connection.
|
| mcsMgrDprsMcsEpGEpLCoPktsFromNetwork |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.11.1.3 |
|
This attribute counts the number of packets received from the
remote LCo via the network.
|
| mcsMgrDprsMcsEpGEpLCoBytesFromNetwork |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.11.1.4 |
|
This attribute counts the number of bytes received from the remote
LCo via the network.
|
| mcsMgrDprsMcsEpGEpLCoPathValue |
.1.3.6.1.4.1.562.2.4.1.122.2.3.4.264.1.1 |
|
This variable represents both the value and the index for the
mcsMgrDprsMcsEpGEpLCoPathTable.
|
