Nortel-Magellan-Passport-ModAtmQosMIB.mib object view, vendor Northern-Telecom-Ltd
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2024 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2024 can import MIB file Nortel-Magellan-Passport-ModAtmQosMIB and use it to monitor vendor specific OID's.
Nortel-Magellan-Passport-ModAtmQosMIB file content
Object view of Nortel-Magellan-Passport-ModAtmQosMIB:
| Scalar Object |
| modFrsAtmNetRowStatusEntry |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1.1 |
|
A single entry in the table represents a single
modFrsAtmNet component.
|
| modFrsAtmNetProvEntry |
.1.3.6.1.4.1.562.2.4.1.16.3.2.10.1 |
|
An entry in the modFrsAtmNetProvTable.
|
| modFrsAtmNetTpmRowStatusEntry |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1.1 |
|
A single entry in the table represents a single
modFrsAtmNetTpm component.
|
| modFrsAtmNetTpmProvEntry |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1 |
|
An entry in the modFrsAtmNetTpmProvTable.
|
| Tabular Object |
| modFrsAtmNetIndex |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1.1.10 |
|
This variable represents the index for the modFrsAtmNet tables.
|
| modFrsAtmNetRowStatus |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
modFrsAtmNet components.
These components cannot be added nor deleted.
|
| modFrsAtmNetComponentName |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| modFrsAtmNetStorageType |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1.1.4 |
|
This variable represents the storage type value for the
modFrsAtmNet tables.
|
| modFrsAtmNetRetryTimerPeriod |
.1.3.6.1.4.1.562.2.4.1.16.3.2.10.1.1 |
|
This attribute specifies the module wide retry timer interval for
failed SPVC calls using Frame Relay to ATM Networking. Changes
to this attribute will take effect on subsequent call setups.
|
| modFrsAtmNetTpmIndex |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1.1.10 |
|
This variable represents the index for the modFrsAtmNetTpm tables.
|
| modFrsAtmNetTpmRowStatus |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
modFrsAtmNetTpm components.
These components can be added.
|
| modFrsAtmNetTpmComponentName |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| modFrsAtmNetTpmStorageType |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1.1.4 |
|
This variable represents the storage type value for the
modFrsAtmNetTpm tables.
|
| modFrsAtmNetTpmEmissionPriority |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1.1 |
|
This attribute specifies the egress emission priority at the FR to
ATM interface. A value of 3 specifies the highest priority, whereas a
value of 0 specifies the lowest priority.
|
| modFrsAtmNetTpmAtmServiceCategory |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1.2 |
|
This attribute specifies the ATM class of service value to be used on
a transport connection.
|
| modFrsAtmNetTpmAvgFrameSize |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1.3 |
|
This attribute specifies the average frame size that is used in the
traffic parameter conversion policy calculations for this transfer
priority to determine the overhead factor for FR to ATM
interworking. The overhead factor affects the granularity of the
bandwidth requirements. The values should be identical across the
network. Otherwise, there may result in bandwidth conversion
inconsistencies.
|
| modFrsAtmNetTpmTrafficParmConversionPolicy |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1.4 |
|
This attribute specifies the traffic parameter conversion policy to use
for this transfer priority to specify the equivalent bandwidth rate at
the FrAtm interface.
Policy 3 characterizes the traffic in the following way:
- ATM traffic descriptor type 6 is selected
- PCR0+1 is based on the AR
- SCR0+1 is based on the CIR and EIR
- MBS0+1 is based on Bc,Be,CIR,EIR and AR
- Takes into account that the instananeous rate of the frame relay
stream can burst above CIR and up tp the AR.
Policy 4 characterizes the traffic in the following way:
- ATM traffic descriptor type 7 or 8 is selected. Type 7 is chosen
when non-conforming cells are to be discarded and type 8 when
non-conforming cells are tagged by UPC traffic policer.
- PCR0+1 is based on the AR
- SCR0 is based on the CIR
- MBS0 is based on Bc,CIR and AR
- There is no direct characterization of EIR. The allowed EIR can be
derived using the difference between the AR and CIR.
Policy 5 characterizes the traffic in the following way:
- ATM traffic descriptor type 7 or 8 is selected . Type 7 is chosen
when non-conforming cells are to be discarded and type 8 when
non-conforming cells are tagged by UPC traffic policer
- PCR0+1 is based on CIR and EIR
- SCR0 is based on the CIR
- MBS0 is based on the Bc,CIR and AR
- The maximum PCR is no longer based on AR but based on the
CIR and EIR.
Policy 6 characterizes the traffic in the following way:
- ATM traffic descriptor type 3 is selected
- PCR0+1 is based only on CIR.
|
| modFrsAtmNetTpmAssignedBandwidthPool |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2.1.5 |
|
This attribute specifies the bandwidth pool which is used to support
this transfer priority. The bandwidth pool is defined in the frAtm Ca
component.
|
| Table |
| modFrsAtmNetRowStatusTable |
.1.3.6.1.4.1.562.2.4.1.16.3.2.1 |
|
This entry controls the addition and deletion of
modFrsAtmNet components.
|
| modFrsAtmNetProvTable |
.1.3.6.1.4.1.562.2.4.1.16.3.2.10 |
|
This group contains information related to the Frame Relay to ATM
interworking.
|
| modFrsAtmNetTpmRowStatusTable |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.1 |
|
This entry controls the addition and deletion of
modFrsAtmNetTpm components.
|
| modFrsAtmNetTpmProvTable |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2.2 |
|
This group specifies the mapping from Frame Relay parameters to
ATM parameters for a Frame Relay using the defined transfer
priority.
|
| Object Identifier |
| modAtmQosMIB |
.1.3.6.1.4.1.562.2.4.2.75 |
| modFrsAtmNet |
.1.3.6.1.4.1.562.2.4.1.16.3.2 |
| modFrsAtmNetTpm |
.1.3.6.1.4.1.562.2.4.1.16.3.2.2 |
| modAtmQosGroup |
.1.3.6.1.4.1.562.2.4.2.75.1 |
| modAtmQosGroupBE |
.1.3.6.1.4.1.562.2.4.2.75.1.5 |
| modAtmQosGroupBE01 |
.1.3.6.1.4.1.562.2.4.2.75.1.5.2 |
| modAtmQosGroupBE01A |
.1.3.6.1.4.1.562.2.4.2.75.1.5.2.2 |
| modAtmQosCapabilities |
.1.3.6.1.4.1.562.2.4.2.75.3 |
| modAtmQosCapabilitiesBE |
.1.3.6.1.4.1.562.2.4.2.75.3.5 |
| modAtmQosCapabilitiesBE01 |
.1.3.6.1.4.1.562.2.4.2.75.3.5.2 |
| modAtmQosCapabilitiesBE01A |
.1.3.6.1.4.1.562.2.4.2.75.3.5.2.2 |
