| atmSvcVpCrossConnectIndex |
.1.3.6.1.2.1.37.1.14.1.1.1.1 |
|
A unique value to identify this SVPC
cross-connect. For each VP associated
with this cross-connect, the agent reports
this cross-connect index value in the
atmVplCrossConnectIdentifer attribute of the
corresponding atmVplTable entries.
|
| atmSvcVpCrossConnectLowIfIndex |
.1.3.6.1.2.1.37.1.14.1.1.1.2 |
|
The value of this object is equal to the
ifIndex value of the ATM interface port for this
SVPC cross-connect. The term low implies
that this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmSvcVpCrossConnectEntry.
|
| atmSvcVpCrossConnectLowVpi |
.1.3.6.1.2.1.37.1.14.1.1.1.3 |
|
The value of this object is equal to the VPI
value associated with the SVPC cross-connect
at the ATM interface that is identified by
atmSvcVpCrossConnectLowIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceCurrentMaxSvpcVpi at the low ATM interface
port.
|
| atmSvcVpCrossConnectHighIfIndex |
.1.3.6.1.2.1.37.1.14.1.1.1.4 |
|
The value of this object is equal to the
ifIndex value of the ATM interface port for
this SVC VP cross-connect. The term high
implies that this ATM interface has the
numerically higher ifIndex value than the
other ATM interface identified in the same
atmSvcVpCrossConnectEntry.
|
| atmSvcVpCrossConnectHighVpi |
.1.3.6.1.2.1.37.1.14.1.1.1.5 |
|
The value of this object is equal to the VPI
value associated with the SVPC cross-connect
at the ATM interface that is identified by
atmSvcVpCrossConnectHighIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceCurrentMaxSvpcVpi at the high ATM interface
port.
|
| atmSvcVpCrossConnectCreationTime |
.1.3.6.1.2.1.37.1.14.1.1.1.6 |
|
The value of the sysUpTime object
at the time this bi-directional SVPC
cross-connect was created. If the current
state was entered prior to the last
re-initialization of the agent, then this
object contains a zero value.
|
| atmSvcVpCrossConnectRowStatus |
.1.3.6.1.2.1.37.1.14.1.1.1.7 |
|
This object is used to delete rows in the
atmSvcVpCrossConnectTable.
|
| atmSvcVcCrossConnectIndex |
.1.3.6.1.2.1.37.1.14.1.2.1.1 |
|
A unique value to identify this SVCC cross-connect.
For each VP associated with this cross-connect, the
agent reports this cross-connect index value in the
atmVclCrossConnectIdentifier attribute of the
corresponding atmVplTable entries.
|
| atmSvcVcCrossConnectLowIfIndex |
.1.3.6.1.2.1.37.1.14.1.2.1.2 |
|
The value of this object is equal to the
ifIndex value of the ATM interface port for this
SVCC cross-connect. The term low implies that
this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmSvcVcCrossConnectEntry.
|
| atmSvcVcCrossConnectLowVpi |
.1.3.6.1.2.1.37.1.14.1.2.1.3 |
|
The value of this object is equal to the VPI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectLowIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceCurrentMaxSvccVpi at the low ATM interface
port.
|
| atmSvcVcCrossConnectLowVci |
.1.3.6.1.2.1.37.1.14.1.2.1.4 |
|
The value of this object is equal to the VCI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectLowIfIndex. The VCI value
cannot exceed the number supported by the
atmInterfaceCurrentMaxSvccVci at the low ATM interface
port.
|
| atmSvcVcCrossConnectHighIfIndex |
.1.3.6.1.2.1.37.1.14.1.2.1.5 |
|
The value of this object is equal to the
ifIndex value for the ATM interface port for
this SVCC cross-connect. The term high implies
that this ATM interface has the numerically
higher ifIndex value than the other ATM interface
identified in the same atmSvcVcCrossConnectEntry.
|
| atmSvcVcCrossConnectHighVpi |
.1.3.6.1.2.1.37.1.14.1.2.1.6 |
|
The value of this object is equal to the VPI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectHighIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceCurrentMaxSvccVpi at the high ATM interface
port.
|
| atmSvcVcCrossConnectHighVci |
.1.3.6.1.2.1.37.1.14.1.2.1.7 |
|
The value of this object is equal to the VCI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectHighIfIndex. The VCI value
cannot exceed the number supported by the
atmInterfaceMaxVciBits at the high ATM interface
port.
|
| atmSvcVcCrossConnectCreationTime |
.1.3.6.1.2.1.37.1.14.1.2.1.8 |
|
The value of the sysUpTime object
at the time this bi-directional SVCC
cross-connect was created. If the current
state was entered prior to the last
re-initialization of the agent, then this
object contains a zero value.
|
| atmSvcVcCrossConnectRowStatus |
.1.3.6.1.2.1.37.1.14.1.2.1.9 |
|
This object is used to delete rows in the
atmSvcVcCrossConnectTable.
|
| atmSigSSCOPConEvents |
.1.3.6.1.2.1.37.1.14.1.3.1.1 |
|
SSCOP Connection Events Counter. This counter counts
the sum of the following errors:
1) SSCOP Connection Disconnect Counter
The abnormal occurrence of this event is
characterized by the expiry of Timer_NO_RESPONSE.
(This event is communicated to the layer management
with MAA-ERROR code P. See ITU-T Q.2110.)
2) SSCOP Connection Initiation Failure
This condition indicates the inability to establish
an SSCOP connection. This event occurs whenever the
number of expiries of the connection control timer
(Timer_CC) equals or exceeds the MaxCC, or upon
receipt of a connection reject message BGREJ PDU.
(This event is communicated to layer management with
MAA-ERROR code O. See ITU-T Q.2110.)
3) SSCOP Connection Re-Establ/Resynch
This event occurs upon receipt of a BGN PDU or
RS PDU.
|
| atmSigSSCOPErrdPdus |
.1.3.6.1.2.1.37.1.14.1.3.1.2 |
|
SSCOP Errored PDUs Counter. This counter counts the
sum of the following errors:
1) Invalid PDUs.
These are defined in SSCOP and consist of PDUs
with an incorrect length (MAA-ERROR code U), an
undefined PDU type code, or that are not 32-bit
aligned.
2) PDUs that result in MAA-ERROR codes and are
discarded.
See MAA-ERROR codes A-D, F-M, and Q-T defined in
ITU-T Q.2110.
|
| atmSigDetectSetupAttempts |
.1.3.6.1.2.1.37.1.14.1.3.1.3 |
|
Call Setup Attempts Counter. This counter counts
the number of call setup attempts (both successful
and unsuccessful) detected on this interface.
|
| atmSigEmitSetupAttempts |
.1.3.6.1.2.1.37.1.14.1.3.1.4 |
|
Call Setup Attempts Counter. This counter counts
the number of call setup attempts (both successful
and unsuccessful) transmitted on this interface.
|
| atmSigDetectUnavailRoutes |
.1.3.6.1.2.1.37.1.14.1.3.1.5 |
|
Number of Route Unavailability detected on this interface.
This counter is incremented when a RELEASE, RELEASE COMPLETE
(only when not preceded by a RELEASE message for the same
call), ADD PARTY REJECT, or STATUS message that
contains one of the following cause code values is
received (Note: These cause values
apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
1 unallocated (unassigned) number
2 no route to specified transit network
3 no route to destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.
|
| atmSigEmitUnavailRoutes |
.1.3.6.1.2.1.37.1.14.1.3.1.6 |
|
Number of Route Unavailability transmitted from this
interface. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
message for the same call), ADD PARTY REJECT, or
STATUS message that contains one of the following cause
code values is transmitted (Note: These cause values apply
to both UNI3.0 and UNI3.1):
Cause Value Meaning
1 unallocated (unassigned) number
2 no route to specified transit network
3 no route to destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.
|
| atmSigDetectUnavailResrcs |
.1.3.6.1.2.1.37.1.14.1.3.1.7 |
|
Number of Resource Unavailability detected on this
interface. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
message for the same call), ADD PARTY REJECT, or
STATUS message that contains one of the following
cause code values is received (Note: These cause
values apply to both UNI3.0 and UNI3.1 unless
otherwise stated):
Cause Value Meaning
35 requested VPCI/VCI not available
37 user cell rate not available (UNI3.1
only)
38 network out of order
41 temporary failure
45 no VPCI/VCI available
47 resource unavailable, unspecified
49 Quality of Service unavailable
51 user cell rate not available (UNI3.0
only)
58 bearer capability not presently
available
63 Service or option not available,
unspecified
92 too many pending add party requests
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.
|
| atmSigEmitUnavailResrcs |
.1.3.6.1.2.1.37.1.14.1.3.1.8 |
|
Number of Resource Unavailability transmitted from this
interface. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE message
for the same call), ADD PARTY REJECT, or STATUS message that
contains one of the following cause code values is transmitted
(Note: These cause values apply to both UNI3.0 and UNI3.1
unless otherwise stated):
Cause Value Meaning
35 requested VPCI/VCI not available
37 user cell rate not available (UNI3.1
only)
38 network out of order
41 temporary failure
45 no VPCI/VCI available
47 resource unavailable, unspecified
49 Quality of Service unavailable
51 user cell rate not available (UNI3.0
only)
58 bearer capability not presently
available
63 Service or option not available,
unspecified
92 too many pending add party requests
NOTE: For this counter, RELEASE COMPLETE messages that are a
reply to a previous RELEASE message and contain the same cause
value, are redundant (for counting purposes) and should not be
counted.
|
| atmSigDetectCldPtyEvents |
.1.3.6.1.2.1.37.1.14.1.3.1.9 |
|
Number of Called Party Responsible For Unsuccessful Call
detected on this interface. This counter is incremented when a
RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE
message for the same call), ADD PARTY REJECT, or STATUS message
that contains one of the following cause code values is
received (Note: These cause values apply to both UNI3.0 and
UNI3.1):
Cause Value Meaning
17 user busy
18 no user responding
21 call rejected
22 number changed
23 user rejects all calls with calling
line identification restriction (CLIR)
27 destination out of order
31 normal, unspecified
88 incompatible destination
NOTE: For this counter, RELEASE COMPLETE messages that are a
reply to a previous RELEASE message and contain the same cause
value, are redundant (for counting purposes) and should not be
counted.
Note: Cause Value #30 'response to STATUS ENQUIRY' was not
included in this memo since it did not apply to a hard
failure.
|
| atmSigEmitCldPtyEvents |
.1.3.6.1.2.1.37.1.14.1.3.1.10 |
|
Number of Called Party Responsible For Unsuccessful Call
transmitted from this interface. This counter is incremented
when a RELEASE, RELEASE COMPLETE (only when not preceded by a
RELEASE message for the same call), ADD PARTY REJECT, or STATUS
message that contains one of the following cause code values is
transmitted (Note: These cause values apply to both UNI3.0 and
UNI3.1):
Cause Value Meaning
17 user busy
18 no user responding
21 call rejected
22 number changed
23 user rejects all calls with calling
line identification restriction (CLIR)
27 destination out of order
31 normal, unspecified
88 incompatible destination
NOTE: For this counter, RELEASE COMPLETE messages that are a
reply to a previous RELEASE message and contain the same cause
value, are redundant (for counting purposes) and should not be
counted.
Note: Cause Value #30 'response to STATUS ENQUIRY' was not
included in this memo since it did not apply to a hard failure.
|
| atmSigDetectMsgErrors |
.1.3.6.1.2.1.37.1.14.1.3.1.11 |
|
Number of Incorrect Messages detected on this interface. The
Incorrect Messages Counter reflects any sort of incorrect
information in a message. This includes:
- RELEASE, RELEASE COMPLETE, ADD PARTY REJECT,
and STATUS messages transmitted, that contain any of
the Cause values listed below.
- Ignored messages. These messages are dropped
because the message was so damaged that it could
not be further processed. A list of dropped
messages is compiled below:
1. Message with invalid protocol discriminator
2. Message with errors in the call reference I.E.
- Bits 5-8 of the first octet not equal to
'0000'
- Bits 1-4 of the first octet indicating a
length other than 3 octets
- RELEASE COMPLETE message received with a
call reference that does not relate to a
call active or in progress
- SETUP message received with call reference
flag incorrectly set to 1
- SETUP message received with a call
reference for a call that is already
active or in progress.
3. Message too short
The following cause values are monitored by this counter (Note:
These cause values apply to both UNI3.0 and UNI3.1 unless
otherwise stated):
Cause Value Meaning
10 VPCI/VCI unacceptable (UNI3.0 only)
36 VPCI/VCI assignment failure (UNI3.1 only)
81 invalid call reference value
82 identified channel does not exist
89 invalid endpoint reference
96 mandatory information element is missing
97 message type non-existent or not
implemented
99 information element non-existent or not
implemented
100 invalid information element contents
101 message not compatible with call state
104 incorrect message length
111 protocol error, unspecified
NOTE: For this counter, RELEASE COMPLETE messages that are
a reply to a previous RELEASE message and contain the same
cause value, are redundant (for counting purposes) and
should not be counted.
|
| atmSigEmitMsgErrors |
.1.3.6.1.2.1.37.1.14.1.3.1.12 |
|
Number of Incorrect Messages transmitted on this interface.
The Incorrect Messages Counter reflects any sort of incorrect
information in a message. This includes:
- RELEASE, RELEASE COMPLETE, ADD PARTY REJECT,
and STATUS messages transmitted or
received, that contain any of the Cause values
listed below.
- Ignored messages. These messages are dropped
because the message was so damaged that it could
not be further processed. A list of dropped
messages is compiled below:
1. Message with invalid protocol discriminator
2. Message with errors in the call reference I.E.
- Bits 5-8 of the first octet not equal to
'0000'
- Bits 1-4 of the first octet indicating a
length other than 3 octets
- RELEASE COMPLETE message received with a
call reference that does not relate to a
call active or in progress
- SETUP message received with call reference
flag incorrectly set to 1
- SETUP message received with a call
reference for a call that is already
active or in progress.
3. Message too short
The following cause values are monitored by this counter
(Note: These cause values apply to both UNI3.0 and UNI3.1
unless otherwise stated):
Cause Value Meaning
10 VPCI/VCI unacceptable (UNI3.0 only)
36 VPCI/VCI assignment failure (UNI3.1 only)
81 invalid call reference value
82 identified channel does not exist
89 invalid endpoint reference
96 mandatory information element is missing
97 message type non-existent or not
implemented
99 information element non-existent or not
implemented
100 invalid information element contents
101 message not compatible with call state
104 incorrect message length
111 protocol error, unspecified
NOTE: For this counter, RELEASE COMPLETE messages that are
a reply to a previous RELEASE message and contain the same
cause value, are redundant (for counting purposes) and
should not be counted.
|
| atmSigDetectClgPtyEvents |
.1.3.6.1.2.1.37.1.14.1.3.1.13 |
|
Number of Calling Party Events detected on this interface.
This counter monitors error events that occur due to the
originating user doing something wrong. This counter is
incremented when a RELEASE, RELEASE COMPLETE (only when not
preceded by a RELEASE message for the same call), ADD PARTY
REJECT, or STATUS message that contains one of the following
cause code values is received (Note: These cause values
apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
28 invalid number format (address incomplete)
43 access information discarded
57 bearer capability not authorized
65 bearer capability not implemented
73 unsupported combination of traffic
parameters
78 AAL parameters cannot be supported (UNI3.1
only)
91 invalid transit network selection
93 AAL parameters cannot be supported (UNI3.0
only)
NOTE: For this counter, RELEASE COMPLETE messages that
are a reply to a previous RELEASE message and contain
the same cause value, are redundant (for counting purposes)
and should not be counted.
|
| atmSigEmitClgPtyEvents |
.1.3.6.1.2.1.37.1.14.1.3.1.14 |
|
Number of Calling Party Events transmitted from this interface.
This counter monitors error events that occur due to the
originating user doing something wrong. This counter is
incremented when a RELEASE, RELEASE COMPLETE (only when not
preceded by a RELEASE message for the same call), ADD PARTY
REJECT, or STATUS message that contains one of the following
cause code values is transmitted (Note: These cause values
apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
28 invalid number format (address incomplete)
43 access information discarded
57 bearer capability not authorized
65 bearer capability not implemented
73 unsupported combination of traffic
parameters
78 AAL parameters cannot be supported (UNI3.1
only)
91 invalid transit network selection
93 AAL parameters cannot be supported (UNI3.0
only)
NOTE: For this counter, RELEASE COMPLETE messages that are
a reply to a previous RELEASE message and contain the same
cause value, are redundant (for counting purposes) and
should not be counted.
|
| atmSigDetectTimerExpireds |
.1.3.6.1.2.1.37.1.14.1.3.1.15 |
|
Number of Timer Expiries detected on this interface. The Timer
Expiries Counter provides a count of network timer expiries, and
to some extent, host or switch timer expiries. The conditions
for incrementing this counter are:
- Expiry of any network timer
- Receipt of a RELEASE or RELEASE COMPLETE
message with Cause #102, 'recovery on
timer expiry'.
NOTE: For this counter, RELEASE COMPLETE messages that are
a reply to a previous RELEASE message and contain the same
cause value, are redundant (for counting purposes) and
should not be counted.
|
| atmSigEmitTimerExpireds |
.1.3.6.1.2.1.37.1.14.1.3.1.16 |
|
Number of Timer Expiries transmitted from this interface.
The Timer Expiries Counter provides a count of network timer
expiries, and to some extent, host or switch timer expiries.
The conditions for incrementing this counter are:
- Expiry of any network timer
- Receipt of a RELEASE or RELEASE COMPLETE
message with Cause #102, 'recovery on
timer expiry'.
NOTE: For this counter, RELEASE COMPLETE messages that are a
reply to a previous RELEASE message and contain the same cause
value, are redundant (for counting purposes) and should not be
counted.
|
| atmSigDetectRestarts |
.1.3.6.1.2.1.37.1.14.1.3.1.17 |
|
Number of Restart Activity errors detected on this interface.
The Restart Activity Counter provides a count of host, switch,
or network restart activity. This counter is incremented when
receiving a RESTART message.
|
| atmSigEmitRestarts |
.1.3.6.1.2.1.37.1.14.1.3.1.18 |
|
Number of Restart Activity errors transmitted from this
interface. The Restart Activity Counter provides a count of
host, switch, or network restart activity. This counter is
incremented when transmitting a RESTART message.
|
| atmSigInEstabls |
.1.3.6.1.2.1.37.1.14.1.3.1.19 |
|
Number of SVCs established at this signalling entity for
incoming connections.
|
| atmSigOutEstabls |
.1.3.6.1.2.1.37.1.14.1.3.1.20 |
|
Number of SVCs established at this signalling entity for
outgoing connections.
|
| atmSigSupportClgPtyNumDel |
.1.3.6.1.2.1.37.1.14.1.4.1.1 |
|
This object indicates whether the Calling Party Number
Information Element is transferred to the called party
address. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportClgPtySubAddr |
.1.3.6.1.2.1.37.1.14.1.4.1.2 |
|
This object indicates whether to accept and transfer the Calling
Party Subaddress Information Element from the calling party to
the called party. Calling party subaddress information shall
only be transferred to the called party if calling party number
delivery is enabled (i.e., atmSigSupportClgPtyNumDel =
'enabled(1)'. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportCldPtySubAddr |
.1.3.6.1.2.1.37.1.14.1.4.1.3 |
|
This object indicates whether to accept, transfer, and deliver
the Called Party Subaddress Information Element from the calling
party to the called party. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportHiLyrInfo |
.1.3.6.1.2.1.37.1.14.1.4.1.4 |
|
This object indicates whether to accept, transfer, and deliver
the Broadband High Layer Information Element from the calling
party to the called party. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportLoLyrInfo |
.1.3.6.1.2.1.37.1.14.1.4.1.5 |
|
This object indicates whether to accept, transfer, and deliver
the Broadband Low Layer Information Element from the calling
party to the called party. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportBlliRepeatInd |
.1.3.6.1.2.1.37.1.14.1.4.1.6 |
|
This object indicates whether to accept, transfer, and deliver
the Broadband Repeat Indicator with two or three instances of
the Broadband Low Layer Information Element for low layer
information selection from the calling party to the called
party. This object's value should always be disabled(2) if
the value of atmSigSupportLolyrInfo is disabled(2).
The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportAALInfo |
.1.3.6.1.2.1.37.1.14.1.4.1.7 |
|
This object indicates whether to accept, transfer, and deliver
the ATM Adaptation Layer Parameters Information Element from the
calling party to the called party. The value of this object can
be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.
|
| atmSigSupportPrefCarrier |
.1.3.6.1.2.1.37.1.14.1.4.1.8 |
|
This parameter identifies the carrier to which intercarrier
calls originated from this interface are routed when transit
network selection information is not provided by the calling
party. If a Carrier Identification Code (CIC) is used the
parameter shall contain the CIC. For three-digit CICs, the first
octet shall be '0' and the CIC is contained in the three
following octets. If the preferred carrier feature is not
supported the value is a zero-length string.
|
| atmSigDescrParamIndex |
.1.3.6.1.2.1.37.1.14.1.5.1.1 |
|
The value of this object is used by the
atmVclGenSigDescrIndex object in the atmVclGenTable to
identify a row in this table.
|
| atmSigDescrParamAalType |
.1.3.6.1.2.1.37.1.14.1.5.1.2 |
|
The AAL type. The value of this object is set to other(1)
when not defined.
|
| atmSigDescrParamAalSscsType |
.1.3.6.1.2.1.37.1.14.1.5.1.3 |
|
The SSCS type used by this entry.
|
| atmSigDescrParamBhliType |
.1.3.6.1.2.1.37.1.14.1.5.1.4 |
|
The Broadband high layer type.
|
| atmSigDescrParamBhliInfo |
.1.3.6.1.2.1.37.1.14.1.5.1.5 |
|
The Broadband high layer information. When
atmSigDescrParamBhliType is set to iso(2), the value of this
object is a zero length string. When
atmSigDescrParamBhliType is set to user(3), the value of
this object is an octet string with length ranging from 0 to
8. When atmSigDescrParamBhliType is set to hiProfile(4),
the value of this object is a length of 4 octet string
containing user to user profile identifier. When
atmSigDescrParamBhliType is set to vendorSpecific(5), the
value of this object is a length of 7 octet string, where
the most significant 3 octets consist of a globally-
administered OUI, and the least significant 4 octets are the
vender administered application OUI.
|
| atmSigDescrParamBbcConnConf |
.1.3.6.1.2.1.37.1.14.1.5.1.6 |
|
The Broadband bearer capability user plane connection
configuration parameter.
|
| atmSigDescrParamBlliLayer2 |
.1.3.6.1.2.1.37.1.14.1.5.1.7 |
|
The Broadband low layer information, protocol type of layer
2. The value of this object is other(1) if layer 2 protocol
is not used.
|
| atmSigDescrParamBlliLayer3 |
.1.3.6.1.2.1.37.1.14.1.5.1.8 |
|
The Broadband low layer information, protocol type of layer
3. The value of this object is other(1) if layer 3 protocol
is not used.
|
| atmSigDescrParamBlliPktSize |
.1.3.6.1.2.1.37.1.14.1.5.1.9 |
|
The default packet size defined in B-LLI.
|
| atmSigDescrParamBlliSnapId |
.1.3.6.1.2.1.37.1.14.1.5.1.10 |
|
The SNAP ID used for Broadband low layer protocol layer 3.
The value of this object is other(1) if
atmSigDescrParamBlliLayer3 is set to other(1).
|
| atmSigDescrParamBlliOuiPid |
.1.3.6.1.2.1.37.1.14.1.5.1.11 |
|
The OUI/PID encoding for Broadband low layer protocol layer
3. The value of this object is a zero length string if
atmSigDescrParamBlliLayer3 is set to other(1). When used,
it is always 5 octets with the most significant octet as the
OUI Octet 1 and the least significant octet as the PID Octet
2.
|
| atmSigDescrParamRowStatus |
.1.3.6.1.2.1.37.1.14.1.5.1.12 |
|
This object is used to create and delete rows in the
atmSigDescrParamTable.
|
| atmIfRegAddrAddress |
.1.3.6.1.2.1.37.1.14.1.6.1.1 |
|
An address registered for a given switch or service interface.
|
| atmIfRegAddrAddressSource |
.1.3.6.1.2.1.37.1.14.1.6.1.2 |
|
The type of address source for a given ATM Address. The value
dynamic(3) is indicated when ILMI is used.
|
| atmIfRegAddrOrgScope |
.1.3.6.1.2.1.37.1.14.1.6.1.3 |
|
This object indicates the organizational scope for
the referenced address. The information of the
referenced address shall not be distributed outside
the indicated scope. Refer to Annex 5.3 of ATM
Forum UNI Signalling 4.0 for guidelines regarding
the use of organizational scopes.
This value cannot be configured for ILMI-registered
addresses.
The default values for organizational scope are
localNetwork(1) for ATM group addresses, and
global(15) for individual addresses.
|
| atmIfRegAddrRowStatus |
.1.3.6.1.2.1.37.1.14.1.6.1.4 |
|
This object is used to create and delete rows in the
atmIfRegisteredAddrTable. Rows created dynamically (e.g., ILMI-
registered addresses) cannot be deleted using this object.
|
| atmVclAddrAddr |
.1.3.6.1.2.1.37.1.14.1.7.1.1 |
|
An ATM address on one end of the VCL. For SVCs, the agent
supplies the value of this object at creation time. For PVC
VCL, the manager can supply the value of this object during
or after the PVC VCL creation.
|
| atmVclAddrType |
.1.3.6.1.2.1.37.1.14.1.7.1.2 |
|
The type of ATM Address represented by the object
atmVclAddrAddr. Choices are either the calling party ATM
address or the called party ATM address.
|
| atmVclAddrRowStatus |
.1.3.6.1.2.1.37.1.14.1.7.1.3 |
|
This object is used to create or destroy an
entry from this table. Note that the manager entity
can only destroy the PVC VCLs.
|
| atmAddrVclAtmIfIndex |
.1.3.6.1.2.1.37.1.14.1.8.1.1 |
|
The interface index of the ATM interface to which this
VCL pertains. This object combined with the
atmAddrVclVpi and atmAddrVclVci objects serves as an
index to the atmVclTable.
|
| atmAddrVclVpi |
.1.3.6.1.2.1.37.1.14.1.8.1.2 |
|
The VPI value of the VCL. This object combined with the
atmAddrVclAtmIfIndex and atmAddrVclVci objects serves as
an index to the atmVclTable.
|
| atmAddrVclVci |
.1.3.6.1.2.1.37.1.14.1.8.1.3 |
|
The VCI value of the VCL. This object combined with the
atmAddrVclAtmIfIndex and atmAddrVclVpi objects serves as
an index to the atmVclTable.
|
| atmAddrVclAddrType |
.1.3.6.1.2.1.37.1.14.1.8.1.4 |
|
The type of ATM Address represented by the object
atmVclAddrAddr. Choices are either calling party address
or called party address.
|
| atmVplStatTotalCellIns |
.1.3.6.1.2.1.37.1.14.1.9.1.1 |
|
The total number of valid ATM cells received by this VPL
including both CLP=0 and CLP=1 cells. The cells are
counted prior to the application of the traffic policing.
|
| atmVplStatClp0CellIns |
.1.3.6.1.2.1.37.1.14.1.9.1.2 |
|
The number of valid ATM cells received by this VPL with
CLP=0. The cells are counted prior to the application of
the traffic policing.
|
| atmVplStatTotalDiscards |
.1.3.6.1.2.1.37.1.14.1.9.1.3 |
|
The total number of valid ATM cells discarded by the
traffic policing entity. This includes cells originally
received with CLP=0 and CLP=1.
|
| atmVplStatClp0Discards |
.1.3.6.1.2.1.37.1.14.1.9.1.4 |
|
The total number of valid ATM cells received with CLP=0 and
discarded by the traffic policing entity.
|
| atmVplStatTotalCellOuts |
.1.3.6.1.2.1.37.1.14.1.9.1.5 |
|
The total number of valid ATM cells transmitted by this
VPL. This includes both CLP=0 and CLP=1 cells.
|
| atmVplStatClp0CellOuts |
.1.3.6.1.2.1.37.1.14.1.9.1.6 |
|
The total number of valid ATM cells transmitted with CLP=0
by this VPL.
|
| atmVplStatClp0Tagged |
.1.3.6.1.2.1.37.1.14.1.9.1.7 |
|
The total number of valid ATM cells tagged by the traffic
policing entity from CLP=0 to CLP=1.
|
| atmVplLogicalPortDef |
.1.3.6.1.2.1.37.1.14.1.10.1.1 |
|
Indicates whether the VPC at this VPL interface is an ATM
Logical Port interface.
|
| atmVplLogicalPortIndex |
.1.3.6.1.2.1.37.1.14.1.10.1.2 |
|
The ifTable index of the ATM logical port interface
associated with this VPL. The distinguished value of zero
indicates that the agent has not (yet) assigned such an
ifTable Index. The zero value must be assigned by the agent
if the value of atmVplLogicalPortDef is set to notLogicalIf,
or if the VPL row is not active.
|
| atmVclStatTotalCellIns |
.1.3.6.1.2.1.37.1.14.1.11.1.1 |
|
The total number of valid ATM cells received by this VCL
including both CLP=0 and CLP=1 cells. The cells are counted
prior to the application of the traffic policing.
|
| atmVclStatClp0CellIns |
.1.3.6.1.2.1.37.1.14.1.11.1.2 |
|
The number of valid ATM cells received by this VCL with
CLP=0. The cells are counted prior to the application of
the traffic policing.
|
| atmVclStatTotalDiscards |
.1.3.6.1.2.1.37.1.14.1.11.1.3 |
|
The total number of valid ATM cells discarded by the
traffic policing entity. This includes cells originally
received with CLP=0 and CLP=1.
|
| atmVclStatClp0Discards |
.1.3.6.1.2.1.37.1.14.1.11.1.4 |
|
The total number of valid ATM cells received with CLP=0
and discarded by the traffic policing entity.
|
| atmVclStatTotalCellOuts |
.1.3.6.1.2.1.37.1.14.1.11.1.5 |
|
The total number of valid ATM cells transmitted by this
VCL. This includes both CLP=0 and CLP=1 cells.
|
| atmVclStatClp0CellOuts |
.1.3.6.1.2.1.37.1.14.1.11.1.6 |
|
The total number of valid ATM cells transmitted with CLP=0
by this VCL.
|
| atmVclStatClp0Tagged |
.1.3.6.1.2.1.37.1.14.1.11.1.7 |
|
The total number of valid ATM cells tagged by the traffic
policing entity from CLP=0 to CLP=1.
|
| atmAal5VclInPkts |
.1.3.6.1.2.1.37.1.14.1.12.1.1 |
|
The number of AAL5 CPCS PDUs received on the AAL5 VCC at
the interface identified by the ifIndex.
|
| atmAal5VclOutPkts |
.1.3.6.1.2.1.37.1.14.1.12.1.2 |
|
The number of AAL5 CPCS PDUs transmitted on the AAL5 VCC
at the interface identified by the ifIndex.
|
| atmAal5VclInOctets |
.1.3.6.1.2.1.37.1.14.1.12.1.3 |
|
The number of octets contained in AAL5 CPCS PDUs received
on the AAL5 VCC at the interface identified by the ifIndex.
|
| atmAal5VclOutOctets |
.1.3.6.1.2.1.37.1.14.1.12.1.4 |
|
The number of octets contained in AAL5 CPCS PDUs
transmitted on the AAL5 VCC at the interface identified by
the ifIndex.
|
| atmVclGenSigDescrIndex |
.1.3.6.1.2.1.37.1.14.1.13.1.1 |
|
The value of this object identifies the row in the ATM
Signalling Descriptor Parameter Table which applies to this
VCL.
|
| atmIntfConfigType |
.1.3.6.1.2.1.37.1.14.1.14.1.1 |
|
The type of connection setup procedures configured for the ATM
interface. Setting this variable to a value of 'other' is not
allowed.
|
| atmIntfActualType |
.1.3.6.1.2.1.37.1.14.1.14.1.2 |
|
The type of connection setup procedures currently being used on
the interface. This may reflect a manually configured value for
the interface type, or may be determined by other means such as
auto-configuration. A value of `autoConfig' indicates that
auto-configuration was requested but has not yet been completed.
|
| atmIntfConfigSide |
.1.3.6.1.2.1.37.1.14.1.14.1.3 |
|
The configured role of the managed entity as one side of the ATM
interface. This value does not apply when the object
atmIntfConfigType is set to `autoConfig', `atmfPnni1Dot0', or
`atmfBici2Dot0'.
|
| atmIntfActualSide |
.1.3.6.1.2.1.37.1.14.1.14.1.4 |
|
The current role used by the managed entity to represent one
side of the ATM interface.
|
| atmIntfIlmiAdminStatus |
.1.3.6.1.2.1.37.1.14.1.14.1.5 |
|
Indicates which components of ILMI are administratively enabled
on this interface. If the 'ilmi' bit is not set, then no ILMI
components are operational. ILMI components other than auto-
configuration that are not represented in the value have their
administrative status determined according to the 'ilmi' bit.
The ILMI auto-configuration component is enabled/disabled by the
atmIntfConfigType object.
|
| atmIntfIlmiOperStatus |
.1.3.6.1.2.1.37.1.14.1.14.1.6 |
|
Indicates which components of ILMI are operational on this
interface.
|
| atmIntfIlmiFsmState |
.1.3.6.1.2.1.37.1.14.1.14.1.7 |
|
Indicates the state of the ILMI Finite State Machine associated
with this interface.
|
| atmIntfIlmiEstablishConPollIntvl |
.1.3.6.1.2.1.37.1.14.1.14.1.8 |
|
The amount of time S between successive transmissions of ILMI
messages on this interface for the purpose of detecting
establishment of ILMI connectivity.
|
| atmIntfIlmiCheckConPollIntvl |
.1.3.6.1.2.1.37.1.14.1.14.1.9 |
|
The amount of time T between successive transmissions of ILMI
messages on this interface for the purpose of detecting loss of
ILMI connectivity. The distinguished value zero disables ILMI
connectivity procedures on this interface.
|
| atmIntfIlmiConPollInactFactor |
.1.3.6.1.2.1.37.1.14.1.14.1.10 |
|
The number K of consecutive polls on this interface for which no
ILMI response message is received before ILMI connectivity is
declared lost.
|
| atmIntfIlmiPublicPrivateIndctr |
.1.3.6.1.2.1.37.1.14.1.14.1.11 |
|
Specifies whether this end of the interface is advertised in
ILMI as a device of the `public' or `private' type.
|
| atmInterfaceConfMaxSvpcVpi |
.1.3.6.1.2.1.37.1.14.1.14.1.12 |
|
The maximum VPI that the signalling stack on the ATM interface
is configured to support for allocation to switched virtual path
connections.
|
| atmInterfaceCurrentMaxSvpcVpi |
.1.3.6.1.2.1.37.1.14.1.14.1.13 |
|
The maximum VPI that the signalling stack on the ATM interface
may currently allocate to switched virtual path connections.
This value is the minimum of atmInterfaceConfMaxSvpcVpi, and the
atmInterfaceMaxSvpcVpi of the interface's UNI/NNI peer.
If the interface does not negotiate with its peer to determine
the maximum VPI that can be allocated to SVPCs on the interface,
then the value of this object must equal
atmInterfaceConfMaxSvpcVpi.
|
| atmInterfaceConfMaxSvccVpi |
.1.3.6.1.2.1.37.1.14.1.14.1.14 |
|
The maximum VPI that the signalling stack on the ATM interface
is configured to support for allocation to switched virtual
channel connections.
|
| atmInterfaceCurrentMaxSvccVpi |
.1.3.6.1.2.1.37.1.14.1.14.1.15 |
|
The maximum VPI that the signalling stack on the ATM interface
may currently allocate to switched virtual channel connections.
This value is the minimum of atmInterfaceConfMaxSvccVpi, and the
atmInterfaceConfMaxSvccVpi of the interface's UNI/NNI peer.
If the interface does not negotiate with its peer to determine
the maximum VPI that can be allocated to SVCCs on the interface,
then the value of this object must equal
atmInterfaceConfMaxSvccVpi.
|
| atmInterfaceConfMinSvccVci |
.1.3.6.1.2.1.37.1.14.1.14.1.16 |
|
The minimum VCI that the signalling stack on the ATM interface
is configured to support for allocation to switched virtual
channel connections.
|
| atmInterfaceCurrentMinSvccVci |
.1.3.6.1.2.1.37.1.14.1.14.1.17 |
|
The minimum VCI that the signalling stack on the ATM interface
may currently allocate to switched virtual channel connections.
This value is the maximum of atmInterfaceConfMinSvccVci, and the
atmInterfaceConfMinSvccVci of the interface's UNI/NNI peer.
If the interface does not negotiate with its peer to determine
the minimum VCI that can be allocated to SVCCs on the interface,
then the value of this object must equal
atmInterfaceConfMinSvccVci.
|
| atmIntfSigVccRxTrafficDescrIndex |
.1.3.6.1.2.1.37.1.14.1.14.1.18 |
|
This object identifies the row in the atmTrafficDescrParamTable
used during ILMI auto-configuration to specify the advertised
signalling VCC traffic parameters for the receive direction.
The traffic descriptor resulting from ILMI auto-configuration of
the signalling VCC is indicated in the atmVclTable.
|
| atmIntfSigVccTxTrafficDescrIndex |
.1.3.6.1.2.1.37.1.14.1.14.1.19 |
|
This object identifies the row in the atmTrafficDescrParamTable
used during ILMI auto-configuration to specify the advertised
signalling VCC traffic parameters for the transmit direction.
The traffic descriptor resulting from ILMI auto-configuration of
the signalling VCC is indicated in the atmVclTable.
|
| atmIntfPvcFailures |
.1.3.6.1.2.1.37.1.14.1.14.1.20 |
|
The number of times the operational status of a PVPL or PVCL on
this interface has gone down.
|
| atmIntfCurrentlyFailingPVpls |
.1.3.6.1.2.1.37.1.14.1.14.1.21 |
|
The current number of VPLs on this interface for which there is
an active row in the atmVplTable having an atmVplConnKind value
of `pvc' and an atmVplOperStatus with a value other than `up'.
|
| atmIntfCurrentlyFailingPVcls |
.1.3.6.1.2.1.37.1.14.1.14.1.22 |
|
The current number of VCLs on this interface for which there is
an active row in the atmVclTable having an atmVclConnKind value
of `pvc' and an atmVclOperStatus with a value other than `up'.
|
| atmIntfPvcFailuresTrapEnable |
.1.3.6.1.2.1.37.1.14.1.14.1.23 |
|
Allows the generation of traps in response to PVCL or PVPL
failures on this interface.
|
| atmIntfPvcNotificationInterval |
.1.3.6.1.2.1.37.1.14.1.14.1.24 |
|
The minimum interval between the sending of
atmIntfPvcFailuresTrap notifications for this interface.
|
| atmIntfLeafSetupFailures |
.1.3.6.1.2.1.37.1.14.1.14.1.25 |
|
Number of setup failures. For root, this is the number of
rejected setup requests and for leaf, this is the number of setup
failure received.
|
| atmIntfLeafSetupRequests |
.1.3.6.1.2.1.37.1.14.1.14.1.26 |
|
Number of setup requests. For root, this includes both incoming
setup request and root intiated setup requests.
|
| atmIlmiSrvcRegIndex |
.1.3.6.1.2.1.37.1.14.1.15.1.1 |
|
The ATM interface where the service defined in this entry can be
made available to an ATM device attached to this interface.
The value of 0 has a special meaning: when an ATM service is
defined in an entry whose atmIlmiSrvcRegIndex is zero, the ATM
service is available to ATM devices connected to any ATM
interface. (default value(s)).
When the user-side of an adjacent device queries the content of
the ILMI service registry MIB (using the ILMI protocol), the
local network-side responds with the ATM services defined in
atmIlmiSrvcRegTable entries, provided that these entries are
indexed by:
- the corresponding ifIndex value (atmIlmiSrvcRegIndex
equal to the ifIndex of the interface to which the
adjacent device is connected) - zero (atmIlmiSrvcRegIndex=0).
|
| atmIlmiSrvcRegServiceID |
.1.3.6.1.2.1.37.1.14.1.15.1.2 |
|
This is the service identifier which uniquely identifies the
type of service at the address provided in the table. The object
identifiers for the LAN Emulation Configuration Server (LECS) and
the ATM Name Server (ANS) are defined in the ATM Forum ILMI
Service Registry MIB. The object identifiers for the ATMARP
Server, the Multicast Address Resolution Server (MARS), and the
NHRP Server (NHS) are defined in RFC 2601, RFC 2602, and RFC
2603, respectively.
|
| atmIlmiSrvcRegAddressIndex |
.1.3.6.1.2.1.37.1.14.1.15.1.3 |
|
An arbitrary integer to differentiate multiple rows containing
different ATM addresses for the same service on the same
interface. This number need NOT be the same as the corresponding
ILMI atmfSrvcRegAddressIndex MIB object.
|
| atmIlmiSrvcRegATMAddress |
.1.3.6.1.2.1.37.1.14.1.15.1.4 |
|
This is the full address of the service. The user-side of the
adjacent device may use this address to establish a connection
with the service.
|
| atmIlmiSrvcRegParm1 |
.1.3.6.1.2.1.37.1.14.1.15.1.5 |
|
An octet string used according to the value of
atmIlmiSrvcRegServiceID.
|
| atmIlmiSrvcRegRowStatus |
.1.3.6.1.2.1.37.1.14.1.15.1.6 |
|
This object is used to create or destroy an entry from this
table.
|
| atmIlmiNetPrefixPrefix |
.1.3.6.1.2.1.37.1.14.1.16.1.1 |
|
The network prefix specified for use in ILMI address
registration.
|
| atmIlmiNetPrefixRowStatus |
.1.3.6.1.2.1.37.1.14.1.16.1.2 |
|
Used to create, delete, activate and de-activate network
prefixes used in ILMI address registration.
|
| atmSwitchAddressIndex |
.1.3.6.1.2.1.37.1.14.1.17.1.1 |
|
An arbitrary index used to enumerate the ATM endsystem addresses
for this switch.
|
| atmSwitchAddressAddress |
.1.3.6.1.2.1.37.1.14.1.17.1.2 |
|
An ATM endsystem address or address prefix used to identify this
switch. When no ESI or SEL field is specified, the switch may
generate the ESI and SEL fields automatically to obtain a
complete 20-byte ATM endsystem address.
|
| atmSwitchAddressRowStatus |
.1.3.6.1.2.1.37.1.14.1.17.1.3 |
|
Used to create, delete, activate, and de-activate addresses used
to identify this switch.
|
| atmVpCrossConnectUserName |
.1.3.6.1.2.1.37.1.14.1.18.1.1 |
|
This is a service user assigned textual representation of a VPC
PVC.
|
| atmVpCrossConnectProviderName |
.1.3.6.1.2.1.37.1.14.1.18.1.2 |
|
This is a system supplied textual representation of VPC PVC. It
is assigned by the service provider.
|
| atmVcCrossConnectUserName |
.1.3.6.1.2.1.37.1.14.1.19.1.1 |
|
This is a service user assigned textual representation of a VCC
PVC.
|
| atmVcCrossConnectProviderName |
.1.3.6.1.2.1.37.1.14.1.19.1.2 |
|
This is a system supplied textual representation of VCC PVC. It
is assigned by the service provider.
|
| atmCurrentlyFailingPVplTimeStamp |
.1.3.6.1.2.1.37.1.14.1.20.1.1 |
|
The time at which this PVPL began to fail.
|
| atmCurrentlyFailingPVclTimeStamp |
.1.3.6.1.2.1.37.1.14.1.21.1.1 |
|
The time at which this PVCL began to fail.
|
