| dsx3LineIndex |
.1.3.6.1.2.1.10.30.5.1.1 |
|
This object should be made equal to ifIndex. The
next paragraph describes its previous usage.
Making the object equal to ifIndex allows proper
use of ifStackTable.
Previously, this object was the identifier of a
DS3/E3 Interface on a managed device. If there is
an ifEntry that is directly associated with this
and only this DS3/E3 interface, it should have the
same value as ifIndex. Otherwise, number the
dsx3LineIndices with an unique identifier
following the rules of choosing a number that is
greater than ifNumber and numbering the inside
interfaces (e.g., equipment side) with even
numbers and outside interfaces (e.g., network side)
with odd numbers.
|
| dsx3IfIndex |
.1.3.6.1.2.1.10.30.5.1.2 |
|
This value for this object is equal to the value
of ifIndex from the Interfaces table of MIB II
(RFC 1213).
|
| dsx3TimeElapsed |
.1.3.6.1.2.1.10.30.5.1.3 |
|
The number of seconds that have elapsed since the
beginning of the near end current error-
measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock,
the current interval exceeds the maximum value,
the agent will return the maximum value.
|
| dsx3ValidIntervals |
.1.3.6.1.2.1.10.30.5.1.4 |
|
The number of previous near end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the value will be the
number of complete 15 minute near end intervals
since the interface has been online. In the case
where the agent is a proxy, it is possible that
some intervals are unavailable. In this case,
this interval is the maximum interval number for
which data is available.
|
| dsx3LineType |
.1.3.6.1.2.1.10.30.5.1.5 |
|
This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface. The
type of interface affects the interpretation of
the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps. The
dsx3ClearChannel value means that the C-bits are
not used except for sending/receiving AIS. The
values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3M23 ANSI T1.107-1988
dsx3SYNTRAN ANSI T1.107-1988
dsx3CbitParity ANSI T1.107a-1990
dsx3ClearChannel ANSI T1.102-1987
e3Framed CCITT G.751
e3Plcp ETSI T/NA(91)18
dsx3M13 ANSI T1.107a-1990.
|
| dsx3LineCoding |
.1.3.6.1.2.1.10.30.5.1.6 |
|
This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
|
| dsx3SendCode |
.1.3.6.1.2.1.10.30.5.1.7 |
|
This variable indicates what type of code is
being sent across the DS3/E3 interface by the
device. (These are optional for E3 interfaces.)
Setting this variable causes the interface to
begin sending the code requested.
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request
dsx3SendDS1LoopCode
requesting to loopback a particular DS1/E1
within a DS3/E3 frame. The DS1/E1 is
indicated in dsx3Ds1ForRemoteLoop.
dsx3SendTestPattern
sending a test pattern.
|
| dsx3CircuitIdentifier |
.1.3.6.1.2.1.10.30.5.1.8 |
|
This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting.
|
| dsx3LoopbackConfig |
.1.3.6.1.2.1.10.30.5.1.9 |
|
This variable represents the desired loopback
configuration of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
its value.
dsx3PayloadLoop
The received signal at this interface is looped
through the device. Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
dsx3LineLoop
The received signal at this interface does not
go through the device (minimum penetration) but
is looped back out.
dsx3OtherLoop
Loopbacks that are not defined here.
dsx3InwardLoop
The sent signal at this interface is looped back
through the device.
dsx3DualLoop
Both dsx1LineLoop and dsx1InwardLoop will be
active simultaneously.
|
| dsx3LineStatus |
.1.3.6.1.2.1.10.30.5.1.10 |
|
This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable
Signal State
2048 dsx3NetEquipOOS Carrier Equipment Out of
Service
|
| dsx3TransmitClockSource |
.1.3.6.1.2.1.10.30.5.1.11 |
|
The source of Transmit Clock.
loopTiming indicates that the recovered receive
clock is used as the transmit clock.
localTiming indicates that a local clock source is
used or that an external clock is attached to the
box containing the interface.
throughTiming indicates that transmit clock is
derived from the recovered receive clock of
another DS3 interface.
|
| dsx3InvalidIntervals |
.1.3.6.1.2.1.10.30.5.1.12 |
|
The number of intervals in the range from 0 to
dsx3ValidIntervals for which no data is available.
This object will typically be zero except in cases
where the data for some intervals are not
available (e.g., in proxy situations).
|
| dsx3LineLength |
.1.3.6.1.2.1.10.30.5.1.13 |
|
The length of the ds3 line in meters. This
object provides information for line build out
circuitry if it exists and can use this object to
adjust the line build out.
|
| dsx3LineStatusLastChange |
.1.3.6.1.2.1.10.30.5.1.14 |
|
The value of MIB II's sysUpTime object at the
time this DS3/E3 entered its current line status
state. If the current state was entered prior to
the last re-initialization of the proxy-agent,
then this object contains a zero value.
|
| dsx3LineStatusChangeTrapEnable |
.1.3.6.1.2.1.10.30.5.1.15 |
|
Indicates whether dsx3LineStatusChange traps
should be generated for this interface.
|
| dsx3LoopbackStatus |
.1.3.6.1.2.1.10.30.5.1.16 |
|
This variable represents the current state of the
loopback on the DS3 interface. It contains
information about loopbacks established by a
manager and remotely from the far end.
The dsx3LoopbackStatus is a bit map represented as
a sum, therefore is can represent multiple
loopbacks simultaneously.
The various bit positions are:
1 dsx3NoLoopback
2 dsx3NearEndPayloadLoopback
4 dsx3NearEndLineLoopback
8 dsx3NearEndOtherLoopback
16 dsx3NearEndInwardLoopback
32 dsx3FarEndPayloadLoopback
64 dsx3FarEndLineLoopback
|
| dsx3Channelization |
.1.3.6.1.2.1.10.30.5.1.17 |
|
Indicates whether this ds3/e3 is channelized or
unchannelized. The value of enabledDs1 indicates
that this is a DS3 channelized into DS1s. The
value of enabledDs3 indicated that this is a DS3
channelized into DS2s. Setting this object will
cause the creation or deletion of DS2 or DS1
entries in the ifTable.
|
| dsx3Ds1ForRemoteLoop |
.1.3.6.1.2.1.10.30.5.1.18 |
|
Indicates which DS1/E1 on this DS3/E3 will be
indicated in the remote ds1 loopback request. A
value of 0 means no DS1 will be looped. A value
of 29 means all DS1s/E1s will be looped.
|
| dsx3CurrentIndex |
.1.3.6.1.2.1.10.30.6.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3CurrentPESs |
.1.3.6.1.2.1.10.30.6.1.2 |
|
The counter associated with the number of P-bit
Errored Seconds.
|
| dsx3CurrentPSESs |
.1.3.6.1.2.1.10.30.6.1.3 |
|
The counter associated with the number of P-bit
Severely Errored Seconds.
|
| dsx3CurrentSEFSs |
.1.3.6.1.2.1.10.30.6.1.4 |
|
The counter associated with the number of
Severely Errored Framing Seconds.
|
| dsx3CurrentUASs |
.1.3.6.1.2.1.10.30.6.1.5 |
|
The counter associated with the number of
Unavailable Seconds.
|
| dsx3CurrentLCVs |
.1.3.6.1.2.1.10.30.6.1.6 |
|
The counter associated with the number of Line
Coding Violations.
|
| dsx3CurrentPCVs |
.1.3.6.1.2.1.10.30.6.1.7 |
|
The counter associated with the number of P-bit
Coding Violations.
|
| dsx3CurrentLESs |
.1.3.6.1.2.1.10.30.6.1.8 |
|
The number of Line Errored Seconds.
|
| dsx3CurrentCCVs |
.1.3.6.1.2.1.10.30.6.1.9 |
|
The number of C-bit Coding Violations.
|
| dsx3CurrentCESs |
.1.3.6.1.2.1.10.30.6.1.10 |
|
The number of C-bit Errored Seconds.
|
| dsx3CurrentCSESs |
.1.3.6.1.2.1.10.30.6.1.11 |
|
The number of C-bit Severely Errored Seconds.
|
| dsx3IntervalIndex |
.1.3.6.1.2.1.10.30.7.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3IntervalNumber |
.1.3.6.1.2.1.10.30.7.1.2 |
|
A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1.
|
| dsx3IntervalPESs |
.1.3.6.1.2.1.10.30.7.1.3 |
|
The counter associated with the number of P-bit
Errored Seconds.
|
| dsx3IntervalPSESs |
.1.3.6.1.2.1.10.30.7.1.4 |
|
The counter associated with the number of P-bit
Severely Errored Seconds.
|
| dsx3IntervalSEFSs |
.1.3.6.1.2.1.10.30.7.1.5 |
|
The counter associated with the number of
Severely Errored Framing Seconds.
|
| dsx3IntervalUASs |
.1.3.6.1.2.1.10.30.7.1.6 |
|
The counter associated with the number of
Unavailable Seconds. This object may decrease if
the occurrence of unavailable seconds occurs across
an interval boundary.
|
| dsx3IntervalLCVs |
.1.3.6.1.2.1.10.30.7.1.7 |
|
The counter associated with the number of Line
Coding Violations.
|
| dsx3IntervalPCVs |
.1.3.6.1.2.1.10.30.7.1.8 |
|
The counter associated with the number of P-bit
Coding Violations.
|
| dsx3IntervalLESs |
.1.3.6.1.2.1.10.30.7.1.9 |
|
The number of Line Errored Seconds (BPVs or
illegal zero sequences).
|
| dsx3IntervalCCVs |
.1.3.6.1.2.1.10.30.7.1.10 |
|
The number of C-bit Coding Violations.
|
| dsx3IntervalCESs |
.1.3.6.1.2.1.10.30.7.1.11 |
|
The number of C-bit Errored Seconds.
|
| dsx3IntervalCSESs |
.1.3.6.1.2.1.10.30.7.1.12 |
|
The number of C-bit Severely Errored Seconds.
|
| dsx3IntervalValidData |
.1.3.6.1.2.1.10.30.7.1.13 |
|
This variable indicates if the data for this
interval is valid.
|
| dsx3TotalIndex |
.1.3.6.1.2.1.10.30.8.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3TotalPESs |
.1.3.6.1.2.1.10.30.8.1.2 |
|
The counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the previous 24 hour interval. Invalid 15 minute
intervals count as 0.
|
| dsx3TotalPSESs |
.1.3.6.1.2.1.10.30.8.1.3 |
|
The counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3TotalSEFSs |
.1.3.6.1.2.1.10.30.8.1.4 |
|
The counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3TotalUASs |
.1.3.6.1.2.1.10.30.8.1.5 |
|
The counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3TotalLCVs |
.1.3.6.1.2.1.10.30.8.1.6 |
|
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3TotalPCVs |
.1.3.6.1.2.1.10.30.8.1.7 |
|
The counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0.
|
| dsx3TotalLESs |
.1.3.6.1.2.1.10.30.8.1.8 |
|
The number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3TotalCCVs |
.1.3.6.1.2.1.10.30.8.1.9 |
|
The number of C-bit Coding Violations encountered
by a DS3 interface in the previous 24 hour
interval. Invalid 15 minute intervals count as 0.
|
| dsx3TotalCESs |
.1.3.6.1.2.1.10.30.8.1.10 |
|
The number of C-bit Errored Seconds encountered
by a DS3 interface in the previous 24 hour
interval. Invalid 15 minute intervals count as 0.
|
| dsx3TotalCSESs |
.1.3.6.1.2.1.10.30.8.1.11 |
|
The number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval. Invalid 15 minute intervals count
as 0.
|
| dsx3FarEndLineIndex |
.1.3.6.1.2.1.10.30.9.1.1 |
|
The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value an dsx3LineIndex object instance.
|
| dsx3FarEndEquipCode |
.1.3.6.1.2.1.10.30.9.1.2 |
|
This is the Far End Equipment Identification code
that describes the specific piece of equipment.
It is sent within the Path Identification
Message.
|
| dsx3FarEndLocationIDCode |
.1.3.6.1.2.1.10.30.9.1.3 |
|
This is the Far End Location Identification code
that describes the specific location of the
equipment. It is sent within the Path
Identification Message.
|
| dsx3FarEndFrameIDCode |
.1.3.6.1.2.1.10.30.9.1.4 |
|
This is the Far End Frame Identification code
that identifies where the equipment is located
within a building at a given location. It is sent
within the Path Identification Message.
|
| dsx3FarEndUnitCode |
.1.3.6.1.2.1.10.30.9.1.5 |
|
This is the Far End code that identifies the
equipment location within a bay. It is sent
within the Path Identification Message.
|
| dsx3FarEndFacilityIDCode |
.1.3.6.1.2.1.10.30.9.1.6 |
|
This code identifies a specific Far End DS3 path.
It is sent within the Path Identification
Message.
|
| dsx3FarEndCurrentIndex |
.1.3.6.1.2.1.10.30.10.1.1 |
|
The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex.
|
| dsx3FarEndTimeElapsed |
.1.3.6.1.2.1.10.30.10.1.2 |
|
The number of seconds that have elapsed since the
beginning of the far end current error-measurement
period. If, for some reason, such as an adjustment
in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will
return the maximum value.
|
| dsx3FarEndValidIntervals |
.1.3.6.1.2.1.10.30.10.1.3 |
|
The number of previous far end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the value will be the
number of complete 15 minute far end intervals
since the interface has been online. In the case
where the agent is a proxy, it is possible that
some intervals are unavailable. In this case,
this interval is the maximum interval number for
which data is available.
|
| dsx3FarEndCurrentCESs |
.1.3.6.1.2.1.10.30.10.1.4 |
|
The counter associated with the number of Far End
C-bit Errored Seconds.
|
| dsx3FarEndCurrentCSESs |
.1.3.6.1.2.1.10.30.10.1.5 |
|
The counter associated with the number of Far End
C-bit Severely Errored Seconds.
|
| dsx3FarEndCurrentCCVs |
.1.3.6.1.2.1.10.30.10.1.6 |
|
The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count.
|
| dsx3FarEndCurrentUASs |
.1.3.6.1.2.1.10.30.10.1.7 |
|
The counter associated with the number of Far End
unavailable seconds.
|
| dsx3FarEndInvalidIntervals |
.1.3.6.1.2.1.10.30.10.1.8 |
|
The number of intervals in the range from 0 to
dsx3FarEndValidIntervals for which no data is
available. This object will typically be zero
except in cases where the data for some intervals
are not available (e.g., in proxy situations).
|
| dsx3FarEndIntervalIndex |
.1.3.6.1.2.1.10.30.11.1.1 |
|
The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex.
|
| dsx3FarEndIntervalNumber |
.1.3.6.1.2.1.10.30.11.1.2 |
|
A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1.
|
| dsx3FarEndIntervalCESs |
.1.3.6.1.2.1.10.30.11.1.3 |
|
The counter associated with the number of Far End
C-bit Errored Seconds encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals. In the case where the agent is
a proxy and data is not available, return
noSuchInstance.
|
| dsx3FarEndIntervalCSESs |
.1.3.6.1.2.1.10.30.11.1.4 |
|
The counter associated with the number of Far End
C-bit Severely Errored Seconds.
|
| dsx3FarEndIntervalCCVs |
.1.3.6.1.2.1.10.30.11.1.5 |
|
The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count.
|
| dsx3FarEndIntervalUASs |
.1.3.6.1.2.1.10.30.11.1.6 |
|
The counter associated with the number of Far End
unavailable seconds.
|
| dsx3FarEndIntervalValidData |
.1.3.6.1.2.1.10.30.11.1.7 |
|
This variable indicates if the data for this
interval is valid.
|
| dsx3FarEndTotalIndex |
.1.3.6.1.2.1.10.30.12.1.1 |
|
The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex.
|
| dsx3FarEndTotalCESs |
.1.3.6.1.2.1.10.30.12.1.2 |
|
The counter associated with the number of Far End
C-bit Errored Seconds encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3FarEndTotalCSESs |
.1.3.6.1.2.1.10.30.12.1.3 |
|
The counter associated with the number of Far End
C-bit Severely Errored Seconds encountered by a
DS3 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.
|
| dsx3FarEndTotalCCVs |
.1.3.6.1.2.1.10.30.12.1.4 |
|
The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0.
|
| dsx3FarEndTotalUASs |
.1.3.6.1.2.1.10.30.12.1.5 |
|
The counter associated with the number of Far End
unavailable seconds encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0.
|
| dsx3FracIndex |
.1.3.6.1.2.1.10.30.13.1.1 |
|
The index value which uniquely identifies the
DS3 interface to which this entry is applicable
The interface identified by a particular value
of this index is the same interface as
identified by the same value an dsx3LineIndex
object instance.
|
| dsx3FracNumber |
.1.3.6.1.2.1.10.30.13.1.2 |
|
The channel number for this entry.
|
| dsx3FracIfIndex |
.1.3.6.1.2.1.10.30.13.1.3 |
|
An index value that uniquely identifies an
interface. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
ifIndex object instance. If no interface is
currently using a channel, the value should be
zero. If a single interface occupies more than
one time slot, that ifIndex value will be found
in multiple time slots.
|
