| l2tpDomainConfigId |
.1.3.6.1.2.1.10.95.1.2.1.1 |
|
The identifier, usually in the form of a Domain
Name (full or partial), describing a single tunnel
endpoint or a domain of tunnel endpoints. This is
typically used as a 'handle' to identify the
tunnel configuration requirements for both incoming
and outgoing tunnel connection attempts. Both the
LAC and LNS could use information provided in the
Host Name AVP attribute however the tunnel initiator
could use other means not specified to identify
the domain's tunnel configuration requirements.
For example; three rows in this table have
l2tpDomainConfigId values of 'lac1.isp.com',
'isp.com' and 'com'. A tunnel endpoint then identifies
itself as 'lac1.isp.com' which would match the
'lac1.isp.com' entry in this table. A second tunnel
endpoint then identifies itself as 'lac2.isp.com'.
This endpoint is then associated with the 'isp.com'
entry of this table.
|
| l2tpDomainConfigAdminState |
.1.3.6.1.2.1.10.95.1.2.1.2 |
|
This object defines the administrative state of this
tunnel domain. Setting this object to disabled(2)
causes all tunnels to be immediately disconnected
and no further tunnels to be either initiated or
accepted. Note that all columnar objects corresponding
to this conceptual row cannot be modified when
the administrative state is enabled EXCEPT those
objects which specifically state otherwise.
|
| l2tpDomainConfigDrainTunnels |
.1.3.6.1.2.1.10.95.1.2.1.3 |
|
Setting this object to 'true' will prevent any new
tunnels and/or sessions from being either initiated
or accepted but does NOT disconnect any active
tunnels/sessions for this tunnel domain. Setting
this object to true(1) causes all tunnels within
this domain to transition to the draining state.
Note that when this occurs the
l2tpTunnelStatsDrainingTunnel status objects of
all of this domain's tunnels should reflect that
they are 'draining'. Setting this object has no
effect on this domain's associated tunnels
l2tpTunnelConfigDrainTunnel configuration objects.
To cancel a drain this object should be set to
false(2). Setting this object to false(2) when
the L2TP object l2tpDrainTunnels is true(1) has
no affect, all domains and their tunnels will
continue to drain.
|
| l2tpDomainConfigAuth |
.1.3.6.1.2.1.10.95.1.2.1.4 |
|
This object describes how tunnel peers belonging
to this domain are to be authenticated. The value
simple(2) indicates that peers are authenticated
simply by their host name as described in the Host
Name AVP. The value challenge(3) indicates that
all peers are challenged to prove their identification.
This mechanism is described in the L2TP protocol.
|
| l2tpDomainConfigSecret |
.1.3.6.1.2.1.10.95.1.2.1.5 |
|
This object is used to configure the shared secret
used during the tunnel authentication phase of
tunnel establishment. This object MUST be accessible
only via requests using both authentication and
privacy. The agent MUST report an empty string in
response to get, get-next and get-bulk requests.
|
| l2tpDomainConfigTunnelSecurity |
.1.3.6.1.2.1.10.95.1.2.1.6 |
|
This object defines whether this tunnel domain
requires that all tunnels are to be secured. The
value of ipsec(3) indicates that all tunnel packets,
control and session, have IP Security headers. The
type of IP Security headers (AH, ESP etc) and how
they are further described is outside the scope of
this document.
|
| l2tpDomainConfigTunnelHelloInt |
.1.3.6.1.2.1.10.95.1.2.1.7 |
|
This object defines the interval in which Hello
(or keep-alive) packets are to be sent by local
peers belonging to this tunnel domain. The value
zero effectively disables the sending of Hello
packets. This object may be modified when the
administrative state is enabled for this conceptual
row.
|
| l2tpDomainConfigTunnelIdleTO |
.1.3.6.1.2.1.10.95.1.2.1.8 |
|
This object defines the period of time that an
established tunnel belonging to this tunnel
domain with no active sessions will wait before
disconnecting the tunnel. A value of zero indicates
that the tunnel will disconnect immediately after the
last session disconnects. A value of -1 leaves the
tunnel up indefinitely. This object may be modified
when the administrative state is enabled for this
conceptual row.
|
| l2tpDomainConfigControlRWS |
.1.3.6.1.2.1.10.95.1.2.1.9 |
|
This object defines the control channel receive
window size for tunnels belonging to this domain. It
specifies the maximum number of packets the tunnel
peer belonging to this domain can send without waiting
for an acknowledgement from this peer.
|
| l2tpDomainConfigControlMaxRetx |
.1.3.6.1.2.1.10.95.1.2.1.10 |
|
This object defines the maximum number of retransmissions
which the L2TP stack will attempt for tunnels belonging
to this domain before assuming that the peer is no
longer responding.
|
| l2tpDomainConfigControlMaxRetxTO |
.1.3.6.1.2.1.10.95.1.2.1.11 |
|
This object defines the maximum retransmission timeout
interval which the L2TP stack will wait for tunnels
belonging to this domain before retransmitting a
control packet that has not been acknowledged.
|
| l2tpDomainConfigPayloadSeq |
.1.3.6.1.2.1.10.95.1.2.1.12 |
|
This object determines whether or not session payload
packets will be requested to be sent with sequence
numbers from tunnel peers belonging to this domain.
The value onDemand(1) allows the L2TP implementation
to initiate payload sequencing when necessary based
on local information (e.g: during LCP/NCP negotiations
or for CCP). The value never(2) indicates that L2TP
will never initiate sequencing but will do sequencing
if asked. The value always(3) indicates that L2TP
will send the Sequencing Required AVP during session
establishment.
|
| l2tpDomainConfigReassemblyTO |
.1.3.6.1.2.1.10.95.1.2.1.13 |
|
This object defines the number of milliseconds that
local peers of this tunnel domain will wait before
processing payload packets that were received out of
sequence (which are waiting for the packet(s) to put
them in sequence). A low value increases the chance
of delayed packets to be discarded (which MAY cause
the PPP decompression engine to reset) while a high
value may cause more queuing and possibly degrade
throughput if packets are truly lost. The default
value for this object is zero which will result in
all delayed packets being lost.
|
| l2tpDomainConfigProxyPPPAuth |
.1.3.6.1.2.1.10.95.1.2.1.14 |
|
This object is used to configure the sending
or acceptance of the PPP Proxy Authentication
AVP's on the LAC or LNS.
|
| l2tpDomainConfigStorageType |
.1.3.6.1.2.1.10.95.1.2.1.15 |
|
The storage type for this conceptual row.
Conceptual rows having the value 'permanent' must
allow write-access at a minimum to:
- l2tpDomainConfigAdminState and
l2tpDomainConfigDrainTunnels at all times
- l2tpDomainConfigSecret if l2tpDomainConfigAuth
has been configured as 'challenge'
It is an implementation issue to decide if a SET for
a readOnly or permanent row is accepted at all. In some
contexts this may make sense, in others it may not. If
a SET for a readOnly or permanent row is not accepted
at all, then a 'wrongValue' error must be returned.
|
| l2tpDomainConfigStatus |
.1.3.6.1.2.1.10.95.1.2.1.16 |
|
The status of this Domain entry. Columnar objects
corresponding to this conceptual row may be modified
according to their description clauses when this
RowStatus object is 'active'.
|
| l2tpDomainStatsTotalTunnels |
.1.3.6.1.2.1.10.95.1.3.1.1 |
|
This object returns the total number of tunnels
that have successfully reached the established
state for this tunnel domain.
|
| l2tpDomainStatsFailedTunnels |
.1.3.6.1.2.1.10.95.1.3.1.2 |
|
This object returns the number of tunnels that
failed (eg: connection timeout, unsupported
or malformed AVP's etc) to reach the established
state for this tunnel domain.
|
| l2tpDomainStatsFailedAuths |
.1.3.6.1.2.1.10.95.1.3.1.3 |
|
This object returns the number of failed tunnel
connection attempts for this domain because the
tunnel peer failed authentication.
|
| l2tpDomainStatsActiveTunnels |
.1.3.6.1.2.1.10.95.1.3.1.4 |
|
This object returns the number of tunnels that
are currently active for this domain.
|
| l2tpDomainStatsTotalSessions |
.1.3.6.1.2.1.10.95.1.3.1.5 |
|
This object returns the total number of sessions
that have successfully reached the established
state for this tunnel domain.
|
| l2tpDomainStatsFailedSessions |
.1.3.6.1.2.1.10.95.1.3.1.6 |
|
This object returns the number of sessions that
failed (eg: connection timeout, unsupported
or malformed AVP's etc) to reach the established
state for this tunnel domain.
|
| l2tpDomainStatsActiveSessions |
.1.3.6.1.2.1.10.95.1.3.1.7 |
|
This object returns the number of sessions that
are currently active for this domain.
|
| l2tpDomainStatsDrainingTunnels |
.1.3.6.1.2.1.10.95.1.3.1.8 |
|
This object indicates if this domain is draining
off sessions from all tunnels.
|
| l2tpDomainStatsControlRxOctets |
.1.3.6.1.2.1.10.95.1.3.1.9 |
|
This object returns the number of control channel
octets received for this tunnel domain.
|
| l2tpDomainStatsControlRxPkts |
.1.3.6.1.2.1.10.95.1.3.1.10 |
|
This object returns the number of control packets
received for this tunnel domain.
|
| l2tpDomainStatsControlTxOctets |
.1.3.6.1.2.1.10.95.1.3.1.11 |
|
This object returns the number of control channel
octets that were transmitted to tunnel endpoints
for this domain.
|
| l2tpDomainStatsControlTxPkts |
.1.3.6.1.2.1.10.95.1.3.1.12 |
|
This object returns the number of control packets
that were transmitted to tunnel endpoints for
this domain.
|
| l2tpDomainStatsPayloadRxOctets |
.1.3.6.1.2.1.10.95.1.3.1.13 |
|
This object returns the number of payload channel
octets that were received for this tunnel domain.
|
| l2tpDomainStatsPayloadRxPkts |
.1.3.6.1.2.1.10.95.1.3.1.14 |
|
This object returns the number of payload packets
that were received for this tunnel domain.
|
| l2tpDomainStatsPayloadRxDiscs |
.1.3.6.1.2.1.10.95.1.3.1.15 |
|
This object returns the number of received payload
packets that were discarded by this tunnel domain.
|
| l2tpDomainStatsPayloadTxOctets |
.1.3.6.1.2.1.10.95.1.3.1.16 |
|
This object returns the number of payload channel
octets that were transmitted to tunnel peers
within this tunnel domain.
|
| l2tpDomainStatsPayloadTxPkts |
.1.3.6.1.2.1.10.95.1.3.1.17 |
|
This object returns the number of payload packets
that were transmitted to tunnel peers within
this tunnel domain.
|
| l2tpDomainStatsControlHCRxOctets |
.1.3.6.1.2.1.10.95.1.3.1.18 |
|
This object is a 64-bit version of
l2tpDomainStatsControlRxOctets.
|
| l2tpDomainStatsControlHCRxPkts |
.1.3.6.1.2.1.10.95.1.3.1.19 |
|
This object is a 64-bit version of
l2tpDomainStatsControlRxPkts.
|
| l2tpDomainStatsControlHCTxOctets |
.1.3.6.1.2.1.10.95.1.3.1.20 |
|
This object is a 64-bit version of
l2tpDomainStatsControlTxOctets.
|
| l2tpDomainStatsControlHCTxPkts |
.1.3.6.1.2.1.10.95.1.3.1.21 |
|
This object is a 64-bit version of
l2tpDomainStatsControlTxPkts.
|
| l2tpDomainStatsPayloadHCRxOctets |
.1.3.6.1.2.1.10.95.1.3.1.22 |
|
This object is a 64-bit version of
l2tpDomainStatsPayloadRxOctets.
|
| l2tpDomainStatsPayloadHCRxPkts |
.1.3.6.1.2.1.10.95.1.3.1.23 |
|
This object is a 64-bit version of
l2tpDomainStatsPayloadRxPkts.
|
| l2tpDomainStatsPayloadHCRxDiscs |
.1.3.6.1.2.1.10.95.1.3.1.24 |
|
This object is a 64-bit version of
l2tpDomainStatsPayloadRxDiscs.
|
| l2tpDomainStatsPayloadHCTxOctets |
.1.3.6.1.2.1.10.95.1.3.1.25 |
|
This object is a 64-bit version of
l2tpDomainStatsPayloadTxOctets.
|
| l2tpDomainStatsPayloadHCTxPkts |
.1.3.6.1.2.1.10.95.1.3.1.26 |
|
This object is a 64-bit version of
l2tpDomainStatsPayloadTxPkts.
|
| l2tpTunnelConfigIfIndex |
.1.3.6.1.2.1.10.95.1.4.1.1 |
|
This value for this object is equal to the value
of ifIndex of the Interfaces MIB for tunnel
interfaces of type L2TP.
|
| l2tpTunnelConfigDomainId |
.1.3.6.1.2.1.10.95.1.4.1.2 |
|
The tunnel domain that this tunnel belongs
to. A LNS tunnel endpoint will typically inherit
this value from the endpoint domain table. A
LAC may be provided with this information during
tunnel setup. When a zero length string is returned
this tunnel does not belong belong to any particular
domain.
|
| l2tpTunnelConfigAuth |
.1.3.6.1.2.1.10.95.1.4.1.3 |
|
This object describes how L2TP tunnel peers are
to be authenticated. The value 'simple' indicates
that peers are authenticated simply by their host
name as described in the Host Name AVP. The value
'challenge' indicates that all peers are challenged
to prove their identification. This mechanism is
described in the L2TP protocol. This object cannot
be modified when the tunnel is in a connecting or
connected state.
|
| l2tpTunnelConfigSecret |
.1.3.6.1.2.1.10.95.1.4.1.4 |
|
This object is used to configure the shared secret
used during the tunnel authentication phase of
tunnel establishment. This object cannot be modified
when the tunnel is in a connecting or connected
state. This object MUST be accessible only via
requests using both authentication and privacy.
The agent MUST report an empty string in response
to get, get-next and get-bulk requests.
|
| l2tpTunnelConfigSecurity |
.1.3.6.1.2.1.10.95.1.4.1.5 |
|
This object defines whether this tunnel is to be
secured. The value of 'ipSec' indicates that all
tunnel packets, control and session, have IP
Security headers. The type of IP Security headers
(AH, ESP etc) and how they are further described
is outside the scope of this document. This object
cannot be modified when the tunnel is in a connecting
or connected state.
|
| l2tpTunnelConfigHelloInterval |
.1.3.6.1.2.1.10.95.1.4.1.6 |
|
This object defines the interval in which Hello
(or keep-alive) packets are to be sent to the
tunnel peer. The value zero effectively disables
the sending of Hello packets. Modifications to this
object have immediate effect.
|
| l2tpTunnelConfigIdleTimeout |
.1.3.6.1.2.1.10.95.1.4.1.7 |
|
This object defines the period of time that an
established tunnel with no sessions will wait
before disconnecting the tunnel. A value of
zero indicates that the tunnel will disconnect
immediately after the last session disconnects.
A value of -1 leaves the tunnel up indefinitely.
Modifications to this object have immediate
effect.
|
| l2tpTunnelConfigControlRWS |
.1.3.6.1.2.1.10.95.1.4.1.8 |
|
This object defines the control channel receive
window size. It specifies the maximum number of
packets the tunnel peer can send without waiting
for an acknowledgement from this peer. This object
cannot be modified when the tunnel is in a con-
necting or connected state.
|
| l2tpTunnelConfigControlMaxRetx |
.1.3.6.1.2.1.10.95.1.4.1.9 |
|
This object defines the number of retransmissions
which the tunnel will attempt before assuming that
the peer is no longer responding. A value of zero
indicates that this peer will not attempt to
retransmit an unacknowledged control packet.
Modifications to this object have immediate
effect.
|
| l2tpTunnelConfigControlMaxRetxTO |
.1.3.6.1.2.1.10.95.1.4.1.10 |
|
This object defines the maximum retransmission timeout
interval which the tunnel will wait before retrans-
mitting a control packet that has not been acknowledged.
Modifications to this object have immediate effect.
|
| l2tpTunnelConfigPayloadSeq |
.1.3.6.1.2.1.10.95.1.4.1.11 |
|
This object determines whether or not session payload
packets will be requested to be sent with sequence
numbers from tunnel peers belonging to this domain.
The value onDemand(1) allows the L2TP implementation
to initiate payload sequencing when necessary based
on local information (e.g: during LCP/NCP negotiations
or for CCP). The value never(2) indicates that L2TP
will never initiate sequencing but will do sequencing
if asked. The value always(3) indicates that L2TP
will send the Sequencing Required AVP during session
establishment. Modifications to this object have
immediate effect.
|
| l2tpTunnelConfigReassemblyTO |
.1.3.6.1.2.1.10.95.1.4.1.12 |
|
This object defines the number of milliseconds that
this tunnel will wait before processing payload packets
that were received out of sequence (which are waiting
for the packet(s) to put them in sequence). A low value
increases the chance of delayed packets to be discarded
(which MAY cause the PPP decompression engine to
reset) while a high value may cause more queuing and
possibly degrade throughput if packets are truly lost.
The default value for this object is zero which will
result in all delayed packets being lost. Modifications
to this object have immediate effect.
|
| l2tpTunnelConfigTransport |
.1.3.6.1.2.1.10.95.1.4.1.13 |
|
This object defines the underlying transport media
that is in use for this tunnel entry. Different tunnel
transports may define MIB extensions to the L2TP tunnel
table to realize the transport layer. For example if the
value of this object is 'udpIp' then the value of ifIndex
for this table may be used to determine state from the
l2tpUdpStatsTable. This object cannot be modified when
the tunnel is in a connecting or connected state.
|
| l2tpTunnelConfigDrainTunnel |
.1.3.6.1.2.1.10.95.1.4.1.14 |
|
Setting this object to 'true' will prevent any new
session from being either initiated or accepted but
does NOT disconnect any active sessions for this
tunnel. Note that when this occurs the
l2tpTunnelStatsDrainingTunnel status object of
this tunnel should reflect that it is 'draining'.
To cancel a drain this object should be set to
false(2). Setting this object to false(2) when
the L2TP objects l2tpDrainTunnels or
l2tpDomainConfigDrainTunnels is true(1) has
no affect, this tunnels will continue to drain.
|
| l2tpTunnelConfigProxyPPPAuth |
.1.3.6.1.2.1.10.95.1.4.1.15 |
|
This object is used to configure the sending
or acceptance of the session PPP Proxy
Authentication AVP's on the LAC or LNS.
|
| l2tpTunnelStatsLocalTID |
.1.3.6.1.2.1.10.95.1.5.1.1 |
|
This object contains the local tunnel Identifier.
|
| l2tpTunnelStatsRemoteTID |
.1.3.6.1.2.1.10.95.1.5.1.2 |
|
This object contains the remote tunnel Identifier.
|
| l2tpTunnelStatsState |
.1.3.6.1.2.1.10.95.1.5.1.3 |
|
This field contains the current state of the
control tunnel.
|
| l2tpTunnelStatsInitiated |
.1.3.6.1.2.1.10.95.1.5.1.4 |
|
This object indicates whether the tunnel was
initiated locally or by the remote tunnel peer.
|
| l2tpTunnelStatsRemoteHostName |
.1.3.6.1.2.1.10.95.1.5.1.5 |
|
This object contains the host name as discovered
during the tunnel establishment phase (via the Host
Name AVP) of the L2TP peer. If the tunnel is idle
this object should maintain its value from the last
time it was connected.
|
| l2tpTunnelStatsRemoteVendorName |
.1.3.6.1.2.1.10.95.1.5.1.6 |
|
This object identifies the vendor name of the peer's
L2TP implementation. If the tunnel is idle this
object should maintain its value from the last time
it was connected.
|
| l2tpTunnelStatsRemoteFirmwareRev |
.1.3.6.1.2.1.10.95.1.5.1.7 |
|
This object contains the tunnel peer's firmware
revision number. If the tunnel is idle this object
should maintain its value from the last time it
was connected.
|
| l2tpTunnelStatsRemoteProtocolVer |
.1.3.6.1.2.1.10.95.1.5.1.8 |
|
This object describes the protocol version and
revision of the tunnel peers implementation. The
first octet contains the protocol version. The
second octet contains the protocol revision.
|
| l2tpTunnelStatsInitialRemoteRWS |
.1.3.6.1.2.1.10.95.1.5.1.9 |
|
This object contains the initial remote peer's
receive window size as indicated by the tunnel peer
(in the RWS AVP) during the tunnel establishment
phase. If the tunnel is idle this object should
maintain its value from the last time it was
connected.
|
| l2tpTunnelStatsBearerCaps |
.1.3.6.1.2.1.10.95.1.5.1.10 |
|
This object describes the Bearer Capabilities of
the tunnel peer. If the tunnel is idle this object
should maintain its value from the last time it was
connected.
|
| l2tpTunnelStatsFramingCaps |
.1.3.6.1.2.1.10.95.1.5.1.11 |
|
This object describes the Framing Capabilities of
the tunnel peer. If the tunnel is idle this object
should maintain its value from the last time it was
connected.
|
| l2tpTunnelStatsControlRxPkts |
.1.3.6.1.2.1.10.95.1.5.1.12 |
|
This object contains the number of control packets
received on the tunnel.
|
| l2tpTunnelStatsControlRxZLB |
.1.3.6.1.2.1.10.95.1.5.1.13 |
|
This object returns a count of the number of Zero
Length Body control packet acknowledgement packets
that were received.
|
| l2tpTunnelStatsControlOutOfSeq |
.1.3.6.1.2.1.10.95.1.5.1.14 |
|
This object returns a count of the number of
control packets that were not received in the
correct order (as per the sequence number)
on this tunnel including out of window
packets.
|
| l2tpTunnelStatsControlOutOfWin |
.1.3.6.1.2.1.10.95.1.5.1.15 |
|
This object contains the number of control
packets that were received outside of the
offered receive window. It is implementation
specific as to whether these packets are queued
or discarded.
|
| l2tpTunnelStatsControlTxPkts |
.1.3.6.1.2.1.10.95.1.5.1.16 |
|
This object contains the number of control
packets that were transmitted to the tunnel
peer.
|
| l2tpTunnelStatsControlTxZLB |
.1.3.6.1.2.1.10.95.1.5.1.17 |
|
This object contains the number of Zero Length
Body control packets transmitted to the tunnel
peer.
|
| l2tpTunnelStatsControlAckTO |
.1.3.6.1.2.1.10.95.1.5.1.18 |
|
This object returns a count of the number of
control packet timeouts due to the lack of a
timely acknowledgement from the tunnel peer.
|
| l2tpTunnelStatsCurrentRemoteRWS |
.1.3.6.1.2.1.10.95.1.5.1.19 |
|
This object contains the current remote receive
window size as determined by the local flow
control mechanism employed.
|
| l2tpTunnelStatsTxSeq |
.1.3.6.1.2.1.10.95.1.5.1.20 |
|
This object contains the next send sequence number
for the control channel.
|
| l2tpTunnelStatsTxSeqAck |
.1.3.6.1.2.1.10.95.1.5.1.21 |
|
This object contains the send sequence number that
the tunnel peer has acknowledged for the control
channel. The flow control state can be determined
by subtracting the l2tpTunnelStatsTxSeq from
l2tpTunnelStatsTxSeqAck and comparing this value
to l2tpTunnelStatsCurrentRemoteRWS (taking into
consideration sequence number wraps).
|
| l2tpTunnelStatsRxSeq |
.1.3.6.1.2.1.10.95.1.5.1.22 |
|
This object contains the next receive sequence
number expected to be received on this control
channel.
|
| l2tpTunnelStatsRxSeqAck |
.1.3.6.1.2.1.10.95.1.5.1.23 |
|
This object contains the last receive sequence
number that was acknowledged back to the tunnel
peer for the control channel.
|
| l2tpTunnelStatsTotalSessions |
.1.3.6.1.2.1.10.95.1.5.1.24 |
|
This object contains the total number of sessions
that this tunnel has successfully connected through
to its tunnel peer since this tunnel was created.
|
| l2tpTunnelStatsFailedSessions |
.1.3.6.1.2.1.10.95.1.5.1.25 |
|
This object contains the total number of sessions
that were initiated but failed to reach the
established phase.
|
| l2tpTunnelStatsActiveSessions |
.1.3.6.1.2.1.10.95.1.5.1.26 |
|
This object contains the total number of sessions
in the established state for this tunnel.
|
| l2tpTunnelStatsLastResultCode |
.1.3.6.1.2.1.10.95.1.5.1.27 |
|
This object contains the last value of the result
code as described in the Result Code AVP which
caused the tunnel to disconnect.
|
| l2tpTunnelStatsLastErrorCode |
.1.3.6.1.2.1.10.95.1.5.1.28 |
|
This object contains the last value of the error
code as described in the Result Code AVP which
caused the tunnel to disconnect.
|
| l2tpTunnelStatsLastErrorMessage |
.1.3.6.1.2.1.10.95.1.5.1.29 |
|
This object contains the last value of the optional
message as described in the Result Code AVP which
caused the tunnel to disconnect.
|
| l2tpTunnelStatsDrainingTunnel |
.1.3.6.1.2.1.10.95.1.5.1.30 |
|
This object indicates if this tunnel is draining
off sessions. This object will return false(2) when
the tunnel is not draining sessions or after the
last session has disconnected when the tunnel is in
the draining state.
|
| l2tpSessionStatsTunnelIfIndex |
.1.3.6.1.2.1.10.95.1.7.1.1 |
|
This object identifies the session's associated
L2TP tunnel ifIndex value.
|
| l2tpSessionStatsLocalSID |
.1.3.6.1.2.1.10.95.1.7.1.3 |
|
This object contains the local assigned session
identifier for this session.
|
| l2tpSessionStatsIfIndex |
.1.3.6.1.2.1.10.95.1.7.1.2 |
|
This object identifies the ifIndex value of the
interface from which PPP packets are being tunneled.
For example this could be a DS0 ifIndex on a
LAC or it would be the PPP ifIndex on the LNS.
|
| l2tpSessionStatsRemoteSID |
.1.3.6.1.2.1.10.95.1.7.1.4 |
|
This object contains the remote assigned session
identifier for this session. When a session is
starting this value may be zero until the remote
tunnel endpoint has responded.
|
| l2tpSessionStatsUserName |
.1.3.6.1.2.1.10.95.1.7.1.5 |
|
This object identifies the peer session name on
this interface. This is typically the login name
of the remote user. If the user name is unknown to
the local tunnel peer then this object will contain
a null string.
|
| l2tpSessionStatsState |
.1.3.6.1.2.1.10.95.1.7.1.6 |
|
This object contains the current state of the
session.
|
| l2tpSessionStatsCallType |
.1.3.6.1.2.1.10.95.1.7.1.7 |
|
This object indicates the type of call and the
role this tunnel peer is providing for this
session. For example, lacIncoming(1) indicates
that this tunnel peer is acting as a LAC and
generated a Incoming-Call-Request to the tunnel
peer (the LNS). Note that tunnel peers can be
both LAC and LNS simultaneously.
|
| l2tpSessionStatsCallSerialNumber |
.1.3.6.1.2.1.10.95.1.7.1.8 |
|
This object contains the serial number that has
been assigned to this session.
|
| l2tpSessionStatsTxConnectSpeed |
.1.3.6.1.2.1.10.95.1.7.1.9 |
|
This object returns the last known transmit
baud rate for this session.
|
| l2tpSessionStatsRxConnectSpeed |
.1.3.6.1.2.1.10.95.1.7.1.10 |
|
This object returns the last known receive
baud rate for this session established.
|
| l2tpSessionStatsCallBearerType |
.1.3.6.1.2.1.10.95.1.7.1.11 |
|
This object describes the bearer type of this
session.
|
| l2tpSessionStatsFramingType |
.1.3.6.1.2.1.10.95.1.7.1.12 |
|
This object describes the framing type of this
session.
|
| l2tpSessionStatsPhysChanId |
.1.3.6.1.2.1.10.95.1.7.1.13 |
|
This object contains the physical channel
identifier for the session.
|
| l2tpSessionStatsDNIS |
.1.3.6.1.2.1.10.95.1.7.1.14 |
|
This object identifies the Dialed Number
Information String that the LAC obtained from
the network for the session. If no DNIS was
provided then a null string will be returned.
|
| l2tpSessionStatsCLID |
.1.3.6.1.2.1.10.95.1.7.1.15 |
|
This object identifies the Calling Line ID
that the LAC obtained from the network for
the session. If no CLID was provided then a
null string will be returned.
|
| l2tpSessionStatsSubAddress |
.1.3.6.1.2.1.10.95.1.7.1.16 |
|
This object identifies the Sub Address that
the LAC obtained from the network for the
session. If no Sub Address was provided then
a null string will be returned.
|
| l2tpSessionStatsPrivateGroupID |
.1.3.6.1.2.1.10.95.1.7.1.17 |
|
This object identifies the Private Group
Identifier used for this tunneled session.
If no Private Group Identifier was provided
then a null string will be returned.
|
| l2tpSessionStatsProxyLcp |
.1.3.6.1.2.1.10.95.1.7.1.18 |
|
Indicates whether the LAC performed proxy LCP
for this session.
|
| l2tpSessionStatsAuthMethod |
.1.3.6.1.2.1.10.95.1.7.1.19 |
|
This object contains the proxy authentication
method employed by the LAC for the session. If
l2tpSessionProxyLcp is false(2) this object
should not be interpreted.
|
| l2tpSessionStatsSequencingState |
.1.3.6.1.2.1.10.95.1.7.1.20 |
|
This object defines which tunnel peers have
requested payload sequencing. The value of
both(4) indicates that both peers have requested
payload sequencing.
|
| l2tpSessionStatsOutSequence |
.1.3.6.1.2.1.10.95.1.7.1.21 |
|
This object returns the total number of packets
received for this session which were received out
of sequence.
|
| l2tpSessionStatsReassemblyTO |
.1.3.6.1.2.1.10.95.1.7.1.22 |
|
This object returns the number of reassembly
timeouts that have occurred for this session.
|
| l2tpSessionStatsTxSeq |
.1.3.6.1.2.1.10.95.1.7.1.23 |
|
This object contains the next send sequence number
for for this session.
|
| l2tpSessionStatsRxSeq |
.1.3.6.1.2.1.10.95.1.7.1.24 |
|
This object contains the next receive sequence
number expected to be received on this session.
|
| l2tpTunnelMapLocalTID |
.1.3.6.1.2.1.10.95.1.8.1.1 |
|
This object contains the local tunnel Identifier.
|
| l2tpTunnelMapIfIndex |
.1.3.6.1.2.1.10.95.1.8.1.2 |
|
This value for this object is equal to the value
of ifIndex of the Interfaces MIB for tunnel
interfaces of type L2TP.
|
| l2tpSessionMapIfIndex |
.1.3.6.1.2.1.10.95.1.9.1.1 |
|
This object identifies the ifIndex value of the
interface which is receiving or sending its packets
over an L2TP tunnel. For example this could be a DS0
ifIndex on a LAC or a PPP ifIndex on the LNS.
|
| l2tpSessionMapTunnelIfIndex |
.1.3.6.1.2.1.10.95.1.9.1.2 |
|
This object identifies the sessions associated
L2TP tunnel ifIndex value. When this object is
set it provides a binding between a particular
interface identified by l2tpSessionMapIfIndex
to a particular tunnel.
|
| l2tpSessionMapLocalSID |
.1.3.6.1.2.1.10.95.1.9.1.3 |
|
This object contains the local assigned session
identifier for this session.
|
| l2tpSessionMapStatus |
.1.3.6.1.2.1.10.95.1.9.1.4 |
|
The status of this session map entry.
|
| l2tpUdpStatsIfIndex |
.1.3.6.1.2.1.10.95.3.1.1.2.1.1 |
|
This value for this object is equal to the
value of ifIndex of the Interfaces MIB for
tunnel interfaces of type L2TP and which have
a L2TP transport of UDP/IP.
|
| l2tpUdpStatsPeerPort |
.1.3.6.1.2.1.10.95.3.1.1.2.1.2 |
|
This object reflects the peer's UDP port number
used for this tunnel. When not known a value of
zero should be returned.
|
| l2tpUdpStatsLocalPort |
.1.3.6.1.2.1.10.95.3.1.1.2.1.3 |
|
This object reflects the local UDP port number
that this tunnel is bound to.
|
