| rs232PortIndex |
.1.3.6.1.2.1.10.33.2.1.1 |
|
A unique value for each port. Its value ranges
between 1 and the value of rs232Number. By
convention and if possible, hardware port numbers
map directly to external connectors. The value for
each port must remain constant at least from one
re-initialization of the network management agent to
the next.
|
| rs232PortType |
.1.3.6.1.2.1.10.33.2.1.2 |
|
The port's hardware type.
|
| rs232PortInSigNumber |
.1.3.6.1.2.1.10.33.2.1.3 |
|
The number of input signals for the port in the
input signal table (rs232PortInSigTable). The table
contains entries only for those signals the software
can detect.
|
| rs232PortOutSigNumber |
.1.3.6.1.2.1.10.33.2.1.4 |
|
The number of output signals for the port in the
output signal table (rs232PortOutSigTable). The
table contains entries only for those signals the
software can assert.
|
| rs232PortInSpeed |
.1.3.6.1.2.1.10.33.2.1.5 |
|
The port's input speed in bits per second.
|
| rs232PortOutSpeed |
.1.3.6.1.2.1.10.33.2.1.6 |
|
The port's output speed in bits per second.
|
| rs232AsyncPortIndex |
.1.3.6.1.2.1.10.33.3.1.1 |
|
A unique value for each port. Its value is the
same as rs232PortIndex for the port.
|
| rs232AsyncPortBits |
.1.3.6.1.2.1.10.33.3.1.2 |
|
The port's number of bits in a character.
|
| rs232AsyncPortStopBits |
.1.3.6.1.2.1.10.33.3.1.3 |
|
The port's number of stop bits.
|
| rs232AsyncPortParity |
.1.3.6.1.2.1.10.33.3.1.4 |
|
The port's sense of a character parity bit.
|
| rs232AsyncPortAutobaud |
.1.3.6.1.2.1.10.33.3.1.5 |
|
A control for the port's ability to automatically
sense input speed.
When rs232PortAutoBaud is 'enabled', a port may
autobaud to values different from the set values for
speed, parity, and character size. As a result a
network management system may temporarily observe
values different from what was previously set.
|
| rs232AsyncPortParityErrs |
.1.3.6.1.2.1.10.33.3.1.6 |
|
Total number of characters with a parity error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.
|
| rs232AsyncPortFramingErrs |
.1.3.6.1.2.1.10.33.3.1.7 |
|
Total number of characters with a framing error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.
|
| rs232AsyncPortOverrunErrs |
.1.3.6.1.2.1.10.33.3.1.8 |
|
Total number of characters with an overrun error,
input from the port since system re-initialization
and while the port state was 'up' or 'test'.
|
| rs232SyncPortIndex |
.1.3.6.1.2.1.10.33.4.1.1 |
|
A unique value for each port. Its value is the
same as rs232PortIndex for the port.
|
| rs232SyncPortClockSource |
.1.3.6.1.2.1.10.33.4.1.2 |
|
Source of the port's bit rate clock. 'split' means
the tranmit clock is internal and the receive clock
is external.
|
| rs232SyncPortFrameCheckErrs |
.1.3.6.1.2.1.10.33.4.1.3 |
|
Total number of frames with an invalid frame check
sequence, input from the port since system
re-initialization and while the port state was 'up'
or 'test'.
|
| rs232SyncPortTransmitUnderrunErrs |
.1.3.6.1.2.1.10.33.4.1.4 |
|
Total number of frames that failed to be
transmitted on the port since system
re-initialization and while the port state was 'up'
or 'test' because data was not available to the
transmitter in time.
|
| rs232SyncPortReceiveOverrunErrs |
.1.3.6.1.2.1.10.33.4.1.5 |
|
Total number of frames that failed to be received
on the port since system re-initialization and while
the port state was 'up' or 'test' because the
receiver did not accept the data in time.
|
| rs232SyncPortInterruptedFrames |
.1.3.6.1.2.1.10.33.4.1.6 |
|
Total number of frames that failed to be received
or transmitted on the port due to loss of modem
signals since system re-initialization and while the
port state was 'up' or 'test'.
|
| rs232SyncPortAbortedFrames |
.1.3.6.1.2.1.10.33.4.1.7 |
|
Number of frames aborted on the port due to
receiving an abort sequence since system
re-initialization and while the port state was 'up'
or 'test'.
|
| rs232InSigPortIndex |
.1.3.6.1.2.1.10.33.5.1.1 |
|
The value of rs232PortIndex for the port to which
this entry belongs.
|
| rs232InSigName |
.1.3.6.1.2.1.10.33.5.1.2 |
|
Identification of a hardware signal, as follows:
rts Request to Send
cts Clear to Send
dsr Data Set Ready
dtr Data Terminal Ready
ri Ring Indicator
dcd Received Line Signal Detector
sq Signal Quality Detector
srs Data Signaling Rate Selector
srts Secondary Request to Send
scts Secondary Clear to Send
sdcd Secondary Received Line Signal Detector
|
| rs232InSigState |
.1.3.6.1.2.1.10.33.5.1.3 |
|
The current signal state.
|
| rs232InSigChanges |
.1.3.6.1.2.1.10.33.5.1.4 |
|
The number of times the signal has changed from
'on' to 'off' or from 'off' to 'on'.
|
| rs232OutSigPortIndex |
.1.3.6.1.2.1.10.33.6.1.1 |
|
The value of rs232PortIndex for the port to which
this entry belongs.
|
| rs232OutSigName |
.1.3.6.1.2.1.10.33.6.1.2 |
|
Identification of a hardware signal, as follows:
rts Request to Send
cts Clear to Send
dsr Data Set Ready
dtr Data Terminal Ready
ri Ring Indicator
dcd Received Line Signal Detector
sq Signal Quality Detector
srs Data Signaling Rate Selector
srts Secondary Request to Send
scts Secondary Clear to Send
sdcd Secondary Received Line Signal Detector
|
| rs232OutSigState |
.1.3.6.1.2.1.10.33.6.1.3 |
|
The current signal state.
|
| rs232OutSigChanges |
.1.3.6.1.2.1.10.33.6.1.4 |
|
The number of times the signal has changed from
'on' to 'off' or from 'off' to 'on'.
|
