| dsx3LineIndex |
.1.3.6.1.2.1.10.30.5.1.1 |
|
This object is the identifier of a DS3/E3
Interface on a managed device. If there is an
ifEntry that is directly associated with this
and only this DS3/E3 interface, it should have
the same value as ifIndex. Otherwise, number
the dsx3LineIndices with an unique identifier
following the rules of choosing a number that
is greater than ifNumber and numbering the
inside interfaces (e.g., equipment side) with
even numbers and outside interfaces (e.g,
network side) with odd numbers.
|
| dsx3IfIndex |
.1.3.6.1.2.1.10.30.5.1.2 |
|
This value for this object is equal to the
value of ifIndex from the Interfaces table of
MIB II (RFC 1213).
|
| dsx3TimeElapsed |
.1.3.6.1.2.1.10.30.5.1.3 |
|
The number of seconds that have elapsed since
the beginning of the near end current error-
measurement period.
|
| dsx3ValidIntervals |
.1.3.6.1.2.1.10.30.5.1.4 |
|
The number of previous near end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute near end
intervals since the interface has been online.
|
| dsx3LineType |
.1.3.6.1.2.1.10.30.5.1.5 |
|
This variable indicates the variety of DS3 C-bit
or E3 application
implementing this interface. The type of
interface affects the interpretation of the
usage and error statistics.
The rate of DS3 is 44.736 Mbps and E3 is
34.368 Mbps.
The dsx3ClearChannel value means that the C-bits
are not used except for sending/receiving
AIS.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3M23 ANSI T1.107-1988
dsx3SYNTRAN ANSI T1.107-1988
dsx3CbitParity ANSI T1.107a-1989
dsx3ClearChannel ANSI T1.102-1987
e3Framed CCITT G.751
e3Plcp ETSI T/NA(91)18.
|
| dsx3LineCoding |
.1.3.6.1.2.1.10.30.5.1.6 |
|
This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
|
| dsx3SendCode |
.1.3.6.1.2.1.10.30.5.1.7 |
|
This variable indicates what type of code is
being sent across the DS3/E3 interface by the
device. (These are optional for E3 interfaces.)
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request
dsx3SendDS1LoopCode
requesting to loopback a particular DS1/E1
within a DS3/E3 frame
dsx3SendTestPattern
sending a test pattern.
|
| dsx3CircuitIdentifier |
.1.3.6.1.2.1.10.30.5.1.8 |
|
This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting.
|
| dsx3LoopbackConfig |
.1.3.6.1.2.1.10.30.5.1.9 |
|
This variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3PayloadLoop
The received signal at this interface is looped
through the device.
Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
dsx3LineLoop
The received signal at this interface does not
go through the device (minimum penetration) but
is looped back out.
dsx3OtherLoop
Loopbacks that are not defined here.
|
| dsx3LineStatus |
.1.3.6.1.2.1.10.30.5.1.10 |
|
This variable indicates the
Line Status of the interface.
It contains loopback state information
and failure state information.
The dsx3LineStatus is a bit map represented
as a sum, therefore,
it can represent multiple failures
and a loopback (see dsx3LoopbackConfig object
for the type of loopback)
simultaneously.
The dsx3NoAlarm should be set if and only if
no other flag is set.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
|
| dsx3TransmitClockSource |
.1.3.6.1.2.1.10.30.5.1.11 |
|
The source of Transmit Clock.
is derived from the recovered receive clock of
another DS3 interface.
|
| dsx3CurrentIndex |
.1.3.6.1.2.1.10.30.6.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3CurrentPESs |
.1.3.6.1.2.1.10.30.6.1.2 |
|
The counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the current 15 minute interval.
|
| dsx3CurrentPSESs |
.1.3.6.1.2.1.10.30.6.1.3 |
|
The counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the current 15 minute interval.
|
| dsx3CurrentSEFSs |
.1.3.6.1.2.1.10.30.6.1.4 |
|
The counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the current 15 minute
interval.
|
| dsx3CurrentUASs |
.1.3.6.1.2.1.10.30.6.1.5 |
|
The counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the current 15 minute interval.
|
| dsx3CurrentLCVs |
.1.3.6.1.2.1.10.30.6.1.6 |
|
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the current 15 minute interval.
|
| dsx3CurrentPCVs |
.1.3.6.1.2.1.10.30.6.1.7 |
|
The counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the current 15 minute interval.
|
| dsx3CurrentLESs |
.1.3.6.1.2.1.10.30.6.1.8 |
|
The number of Line Errored Seconds encountered by
a DS3/E3 interface in the current 15 minute
interval.
|
| dsx3CurrentCCVs |
.1.3.6.1.2.1.10.30.6.1.9 |
|
The number of C-bit Coding Violations encountered
by a DS3 interface in the current 15 minute
interval.
|
| dsx3CurrentCESs |
.1.3.6.1.2.1.10.30.6.1.10 |
|
The number of C-bit Errored Seconds encountered
by a DS3 interface in the current 15 minute
interval.
|
| dsx3CurrentCSESs |
.1.3.6.1.2.1.10.30.6.1.11 |
|
The number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the current 15
minute interval.
|
| dsx3IntervalIndex |
.1.3.6.1.2.1.10.30.7.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3IntervalNumber |
.1.3.6.1.2.1.10.30.7.1.2 |
|
A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).
|
| dsx3IntervalPESs |
.1.3.6.1.2.1.10.30.7.1.3 |
|
The counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
one of the previous 96, individual 15 minute,
intervals.
|
| dsx3IntervalPSESs |
.1.3.6.1.2.1.10.30.7.1.4 |
|
The counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals.
|
| dsx3IntervalSEFSs |
.1.3.6.1.2.1.10.30.7.1.5 |
|
The counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3IntervalUASs |
.1.3.6.1.2.1.10.30.7.1.6 |
|
The counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals.
|
| dsx3IntervalLCVs |
.1.3.6.1.2.1.10.30.7.1.7 |
|
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in one of the previous 96, individual 15
minute, intervals.
|
| dsx3IntervalPCVs |
.1.3.6.1.2.1.10.30.7.1.8 |
|
The counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in one of the previous 96, individual 15 minute,
intervals.
|
| dsx3IntervalLESs |
.1.3.6.1.2.1.10.30.7.1.9 |
|
The number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in one of the previous 96, individual
15 minute, intervals.
|
| dsx3IntervalCCVs |
.1.3.6.1.2.1.10.30.7.1.10 |
|
The number of C-bit Coding Violations encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3IntervalCESs |
.1.3.6.1.2.1.10.30.7.1.11 |
|
The number of C-bit Errored Seconds encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3IntervalCSESs |
.1.3.6.1.2.1.10.30.7.1.12 |
|
The number of C-bit Severely Errored Seconds
encountered by a DS3 interface in one of the
previous 96, individual 15 minute, intervals.
|
| dsx3TotalIndex |
.1.3.6.1.2.1.10.30.8.1.1 |
|
The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance.
|
| dsx3TotalPESs |
.1.3.6.1.2.1.10.30.8.1.2 |
|
The counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the previous 24 hour interval
|
| dsx3TotalPSESs |
.1.3.6.1.2.1.10.30.8.1.3 |
|
The counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the previous 24 hour interval.
|
| dsx3TotalSEFSs |
.1.3.6.1.2.1.10.30.8.1.4 |
|
The counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the previous 24 hour
interval.
|
| dsx3TotalUASs |
.1.3.6.1.2.1.10.30.8.1.5 |
|
The counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the previous 24 hour interval.
|
| dsx3TotalLCVs |
.1.3.6.1.2.1.10.30.8.1.6 |
|
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the previous 24 hour interval.
|
| dsx3TotalPCVs |
.1.3.6.1.2.1.10.30.8.1.7 |
|
The counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the previous 24 hour interval.
|
| dsx3TotalLESs |
.1.3.6.1.2.1.10.30.8.1.8 |
|
The number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in the previous 24 hour interval.
|
| dsx3TotalCCVs |
.1.3.6.1.2.1.10.30.8.1.9 |
|
The number of C-bit Coding Violations encountered
by a DS3 interface in the previous 24 hour
interval.
|
| dsx3TotalCESs |
.1.3.6.1.2.1.10.30.8.1.10 |
|
The number of C-bit Errored Seconds encountered
by a DS3 interface in the previous 24 hour
interval.
|
| dsx3TotalCSESs |
.1.3.6.1.2.1.10.30.8.1.11 |
|
The number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval.
|
| dsx3FarEndLineIndex |
.1.3.6.1.2.1.10.30.9.1.1 |
|
The index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The
interface identified by a particular value of
this index is the same interface as identified
by the same value an dsx3LineIndex object
instance.
|
| dsx3FarEndEquipCode |
.1.3.6.1.2.1.10.30.9.1.2 |
|
This is the Far End Equipment Identification code
that describes the specific piece of equipment.
It is sent within the Path
Identification Message.
|
| dsx3FarEndLocationIDCode |
.1.3.6.1.2.1.10.30.9.1.3 |
|
This is the Far End Location Identification code
that describes the specific location of the
equipment.
It is sent within the Path
Identification Message.
|
| dsx3FarEndFrameIDCode |
.1.3.6.1.2.1.10.30.9.1.4 |
|
This is the Far End Frame Identification code
that identifies where the equipment is located
within a building at a given location.
It is sent within the Path
Identification Message.
|
| dsx3FarEndUnitCode |
.1.3.6.1.2.1.10.30.9.1.5 |
|
This is the Far End code
that identifies the equipment location within a bay.
It is sent within the Path
Identification Message.
|
| dsx3FarEndFacilityIDCode |
.1.3.6.1.2.1.10.30.9.1.6 |
|
This code identifies a specific Far End DS3 path.
It is sent within the Path
Identification Message.
|
| dsx3FarEndCurrentIndex |
.1.3.6.1.2.1.10.30.10.1.1 |
|
The index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The interface
identified by a particular value of this index is
the same interface as identified by the same value
an dsx3LineIndex object instance.
|
| dsx3FarEndTimeElapsed |
.1.3.6.1.2.1.10.30.10.1.2 |
|
The number of seconds that have elapsed since the
beginning of the far end current error-measurement
period.
|
| dsx3FarEndValidIntervals |
.1.3.6.1.2.1.10.30.10.1.3 |
|
The number of previous far end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute far end intervals
since the interface has been online.
|
| dsx3FarEndCurrentCESs |
.1.3.6.1.2.1.10.30.10.1.4 |
|
The counter associated with the number of Far
Far End C-bit Errored Seconds encountered by a DS3
interface in the current 15 minute interval.
|
| dsx3FarEndCurrentCSESs |
.1.3.6.1.2.1.10.30.10.1.5 |
|
The counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in the current 15
minute interval.
|
| dsx3FarEndCurrentCCVs |
.1.3.6.1.2.1.10.30.10.1.6 |
|
The counter associated with the number of
Far End C-bit Coding Violations reported via
the far end block error count
encountered by a
DS3 interface in the current 15 minute interval.
|
| dsx3FarEndCurrentUASs |
.1.3.6.1.2.1.10.30.10.1.7 |
|
The counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in the current 15 minute interval.
|
| dsx3FarEndIntervalIndex |
.1.3.6.1.2.1.10.30.11.1.1 |
|
The index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The
interface identified by a particular value of
this index is the same interface as identified
by the same value an dsx3LineIndex object
instance.
|
| dsx3FarEndIntervalNumber |
.1.3.6.1.2.1.10.30.11.1.2 |
|
A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes
interval (assuming that all 96 intervals are
valid).
|
| dsx3FarEndIntervalCESs |
.1.3.6.1.2.1.10.30.11.1.3 |
|
The counter associated with the number of
Far End C-bit Errored Seconds encountered
by a DS3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3FarEndIntervalCSESs |
.1.3.6.1.2.1.10.30.11.1.4 |
|
The counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in one of the
previous 96, individual 15 minute, intervals.
|
| dsx3FarEndIntervalCCVs |
.1.3.6.1.2.1.10.30.11.1.5 |
|
The counter associated with the number of
Far End C-bit Coding Violations reported via
the far end block error count
encountered by a
DS3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3FarEndIntervalUASs |
.1.3.6.1.2.1.10.30.11.1.6 |
|
The counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in one of the previous 96,
individual 15 minute, intervals.
|
| dsx3FarEndTotalIndex |
.1.3.6.1.2.1.10.30.12.1.1 |
|
The index value which uniquely identifies the
DS3 interface
to which this entry is applicable. The interface
identified by a particular value of this index is
the same interface as identified by the same value
an dsx3LineIndex object instance.
|
| dsx3FarEndTotalCESs |
.1.3.6.1.2.1.10.30.12.1.2 |
|
The counter associated with the number of Far
End C-bit Errored Seconds encountered by a DS3
interface in the previous 24 hour interval.
|
| dsx3FarEndTotalCSESs |
.1.3.6.1.2.1.10.30.12.1.3 |
|
The counter associated with the number of
Far End C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval.
|
| dsx3FarEndTotalCCVs |
.1.3.6.1.2.1.10.30.12.1.4 |
|
The counter associated with the number of
Far End C-bit Coding Violations reported via the
far end block error count
encountered by a
DS3 interface in the previous 24 hour interval.
|
| dsx3FarEndTotalUASs |
.1.3.6.1.2.1.10.30.12.1.5 |
|
The counter associated with the number of
Far End unavailable seconds
encountered by a
DS3 interface in the previous 24 hour interval.
|
| dsx3FracIndex |
.1.3.6.1.2.1.10.30.13.1.1 |
|
The index value which uniquely identifies the
DS3 interface to which this entry is applicable
The interface identified by a particular
value of this index is the same interface as
identified by the same value an dsx3LineIndex
object instance.
|
| dsx3FracNumber |
.1.3.6.1.2.1.10.30.13.1.2 |
|
The channel number for this entry.
|
| dsx3FracIfIndex |
.1.3.6.1.2.1.10.30.13.1.3 |
|
An index value that uniquely identifies an
interface. The interface identified by a particular
value of this index is the same interface
as identified by the same value an ifIndex
object instance. If no interface is currently using
a channel, the value should be zero. If a
single interface occupies more than one time
slot, that ifIndex value will be found in multiple
time slots.
|
