| dsx3LineNum |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.1 |
|
This object is the identifier of a DS3/E3
Interface on a managed device.
The range supported depends upon the type of
the card(controller card, service module).
For 1 port Card : Range is 1..1
Example : CESM-T3E3
For 2 Port Card : Range is 1..2
Example : PXM1-2T3E3.
For 3 Port Card : Range is 1..3
Example: SRM-3T3
|
| cwDsx3LineType |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.2 |
|
This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3CbitParity ANSI T1.107a-1990 [9a]
g832-g804 ITU-T G.832, G.804
dsx3M23 ANSI T1.107-1988 [9]
g751 ITU-T G.751
CESM-T3 supports only ds3Unframed linetype.
CESM-E3 supports only e3Unframed linetype.
|
| cwDsx3LineCoding |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.3 |
|
This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
dsx3B3ZS(1) : Bipolar 3-Zero Substitution(B3ZS) suppression.
e3HDB3 (2) : High-Density Bipolar 3(HDB3) suppression.
|
| cwDsx3LineLength |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.4 |
|
This object specifies the length of the
DS3 Line. This object provides information
for line build out circuitry if it exists
and can use this object to adjust the
line build out.
|
| dsx3LineOOFCriteria |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.5 |
|
This object specifies the out of frame decision
criteria.
OOF is declared when errors are detected in the
framing octets for four consecuitive frames.
fBits3Of8(1) : an OOF condition is declared if at
least 3 of 8 framing bits are in error.
fBits3Of16(2): an OOF is declared if 3 of 16 framing
bits are found to be in error.
notApplicable(3) : used in case where it is not
applicable. This value can not be set.
This object is not applicable when cwDsx3LineType is
set to g832-g804(2) or g751(4).
This object is not applicable for CESM-T3/E3
|
| dsx3LineAIScBitsCheck |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.6 |
|
If check C-Bits options is chosen then AIS is declared
when 1010 pattern is found and C-Bits are all zero.
In the other case an AIS condition is declared when the
AIS pattern 1010... is detected irrespective of the state
of the C Bits.
This object does not apply to the E3 interface.
The value notApplicable(3) is used in case of interfaces
where this object is not applicable.
This object is not applicable for CESM-T3/E3.
|
| dsx3LineLoopbackCommand |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.7 |
|
This variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3RemoteLineLoop
Near End loops back Remote data
dsx3LocalLineLoop
Near End loops back Local data(outbound).
dsx3InboundLoopback
Near End in bound loopback Local data(inbound).
|
| dsx3LineRcvFEACValidation |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.8 |
|
This entry specifies the FEAC code validation criteria.
fFEACCodes4Of5(1) : a valid FEAC code is declared if
4 of 5 codes match.
fFEACCodes8Of10(2): a valid FEAC code is declared if
8 of 10 codes match.
fFEACCodesDisable(3) : Do not respond to any valid FEAC code.
This object is not applicable to E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3LineXmtFEACCode |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.9 |
|
This variable indicates what bit-oriented code to transmit
over the far-end alarm and control (FEAC) channel.
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request.
dsx3SendDS1LoopCode
sending a request to put part of DS1/E1 within
T3/E3 respectively into loopback.
dsx3SendTestPattern
sending a test pattern.
This object is not applicable for CESM-T3/E3
|
| dsx3LineBERTEnable |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.10 |
|
This object enables/disables the BERT function on
an interface.
The possible values are :
disabled(1): disables port BERT functionality
enabled (2): enables port BERT functionality.
value specified in dsx3LineBERTPattern
is transmitted over the interface.
The far end may be looped back and the
test pattern verified.
|
| dsx3LineBERTPattern |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.11 |
|
This object defines the test bit pattern to be
used for BERT.
The possible values are :
Repetitive Patterns
allZero(1): All Zeroes(Continuous spaces). This is
repeating pattern of zeros(...000...).
The use of this pattern is to test and verify
that the ones density policing mechanism is
functioning properly. This pattern must be
used in circuits optioned for B8ZS.
allOnes(2): All Ones(Continuous Marks). This is repeating
pattern of ones(...1111...). This provides
testing of maximum power level requirements.
The all one pattern test causes the repeater
to consume the maximum amount of power.
If there is insufficient DC span power then the
repeater may begin to fail.
Typically this pattern is used for a simple
continuity check. It may also be used to detect
the presence of unwanted loop in the network.
alternateOneZero(3): Alternate one/zero pattern(..1010..). This
pattern produces a 50% ones density. It is
used to stress the repeater's DC power
consumption.
doubleOneZero(4): Double alternate one/zero(..1100..).
userOneWord(5),
userTwoWords(6),
userThreeWords(7),
userFourWords(8),
pattern2p15minus1(9) :
This is the 2^15-1(32767 bit length)
pattern as specified in ITU O.151.
It has the maximum of 15(inverted) sequential zeros.
This sequence is primarily intended for
error and jitter measurements at bit
rates of 1544, 2048, 6312, 8448,
32064 and 44736 kbit/s.
pattern2p20minus1(10):
This is the 2^20-1(1048575 bits in length)
pattern specified in ITU O.153.It has
the maximum of 19(non-inverted) sequential
zeros. This pattern is primarily intended
for error measurements at bit rates up to
73kbit/s. This pattern stresses the
equalization and timing recovery circuitry
of line repeaters.
pattern2p23minus1(11):
This is the 2^23-1(1048575 bits in length) pattern.
|
| dsx3LineBERTResult |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.12 |
|
Result of BERT Test. The value in this object
is not applicable if dsx3LineBERTEnable is set to
disabled(1).
|
| dsx3BERTResultClrButton |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.13 |
|
Setting this object to clear(2) causes the BERT
result field to get cleared.
|
| dsx3TrailTraceOption |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.14 |
|
This object is used for enabling/disabling
G.832 Trail Trace. The trail trace is used to
repetitively transmit a trail access point identifier
so that a trail receiving terminal can verify its
continued connection to the intended transmitter.
It uses a 16-byte numbering format (see Rec E.164).
The first byte of the string is a frame start marker
and includes the result of a CRC-7 calculation over
the previous frame.
The value of this object is set to disable(1) in case
of cards where this feature is not supported.
This object is not applicable for FRSM-VHS and
CESM-T3/E3.
|
| dsx3TxTrailTrace |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.15 |
|
This object is used for specifying the
data to be used for G.832 Trail Trace ID/String.
This object is applicable only for E3 interfaces
with G.832 framing.
The trail trace ID is a 16 octet field that
contains 1 octet of CRC-7(first octet) and 15
octets of data.
The CRC-7 is automatically calculated by the
system(card supporting this feature).
The format of the value is:
Frame Start Marker Error(HEX): CRC-7
Bytes 2-6 (ASCII) [Byte 1-5 of this object]
Bytes 7-11 (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
This object is not applicable for FRSM-VHS and
CESM-T3/E3.
|
| dsx3RxTrailTrace |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.16 |
|
Received G.832 Trail Trace string.
The format of the value is:
First byte indicates CRC-7(frame start marker).
Bytes 2-6 (ASCII) [Byte 1-5 of this object]
Bytes 7-11 (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
The value of all zeroes indicates bad CRC-7.
This object is not applicable for FRSM-VHS and
CESM-T3/E3.
|
| dsx3TxTimingMarker |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.17 |
|
Transmitted timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is traceable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3.
|
| dsx3RxTimingMarker |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.18 |
|
Received timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is tracable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3.
|
| dsx3TxPayloadType |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.19 |
|
This object specifies the G.832 payload type
for transmit data.
The possible values are :
unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3): ATM
sdhtu12s (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3
|
| dsx3RxPayloadType |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.20 |
|
Received payload type field in G.832 byte
The possible values are :
unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3): ATM
sdhtu12s (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3
|
| dsx3TxTumf |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.21 |
|
This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This is not supported in FRSM-VHS and CESM-T3/E3.
|
| dsx3RxTumf |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.22 |
|
This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This object is not supported in FRSM-VHS
and CESM-T3/E3.
|
| dsx3LineEnable |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.23 |
|
This object is used for enabling/disabling an interface
and modifying the interface configuration.
The possible values are:
disable (1): Interface is administratively down
enable (2): Interface is administratively up.
modify (3): Used for modifying the parameters
of an interface that has been already
enabled(administratively up).
To modify the parameters of this table, the value
of this object must be set to enable(2) or modify(3).
|
| dsx3FarEndLoopbkLineNum |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.24 |
|
Specify which DS1 or DS3 line in the far-end for the
loopback testing.
For CESM-T3/E3, only ds3line(30) is valid.
|
| dsx3LineXmtClockSrc |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.25 |
|
The source of the transmit clock.
backplaneClk(2) : clock source is from the backplane.
recoverClk (3) : clock source is derived from another
t3 interface.
localClk (4) : clock source is from a local
oscillator on the card
|
| dsx3FarEndLoopbkLineStatus |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.26 |
|
This is a bitmap of the DSX3 FarEnd line
loopback status bits
Bit Position Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 DS1 Line 4
5 DS1 Line 5
6 DS1 Line 6
7 DS1 Line 7
8 DS1 Line 8
9 DS1 Line 9
10 DS1 Line 10
11 DS1 Line 11
12 DS1 Line 12
...
...
...
28 DS1 Line 28
29 all DS1 Lines
30 DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid.
|
| dsx3LineEqualizer |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.27 |
|
This object indicates whether the internal equalizer
is being used or bypassed. Set this value depending on
the line equipment to which the receiver is attached.
intrnlequalizer(1): Use internal line equalizer
extequalizer(2) : Use External equalizer or bypass internal
equalizer.
|
| dsx3NearEndLoopbkLineStatus |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.28 |
|
This is a bitmap of the DSX3 NearEnd line
loopback status bits
BitPosition Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 DS1 Line 4
5 DS1 Line 5
6 DS1 Line 6
7 DS1 Line 7
8 DS1 Line 8
9 DS1 Line 9
10 DS1 Line 10
11 DS1 Line 11
12 DS1 Line 12
...
...
...
28 DS1 Line 28
29 DS1 Line 29
30 DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid.
|
| dsx3SubRateEnable |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.29 |
|
This variable controls whether the DS3 subrates are
enabled or not. The DS3 subrate is part of
DSU functionality.
This object is currently supported only in FRSM-VHS
cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.
|
| dsx3DsuSelect |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.30 |
|
The dsx3DsuSelect variable controls the type of DSU mode
to be selected. The 'dsx3SubRateEnable' has to be set to
'enable' before selecting the mode in 'dsx3DsuSelect'.
The possible values for this are :
dl3100Mode - Indicates compatibility with Digital Link Inc's
DL3100 DSU mode of operation. This mode permits
line rates to be in multiples of 300 Kbps.
adcKentroxMode - Indicates compatibility with ADC Kentrox's DSU.
This mode permits line rates to be in multiples
of 500 Kbps.
larsCom - Indicates compatability with LarsCom DSU.
clearChannel - Indicates the standard G.751 framing format
(12 overhead bits and 1524 data bits in an E3
frame).This option is supported only in FRSM-2E3.
dsuAlgorithm1 - dsuAlgorith4 - Presently this is not used in any of
the cards.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.
|
| dsx3LineRate |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.31 |
|
The desired line rate when 'dsx3SubRateEnable' is enabled.
If dsx3DsuSelect is set to 'dl3100Mode', the line rate can
be configured in steps of 300 Kbps.
If dsx3DsuSelect is set to 'adcKentroxMode', the line rate can
be configured in steps of 500 Kbps.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality.
|
| dsx3LineScrambleEnable |
.1.3.6.1.4.1.351.110.4.4.1.1.1.1.32 |
|
This variable turns the scrambling feature ON/OFF
The scrambling is a technique that enables framing
to be maintained on certain medium-speed edge and
trunk interfaces.
This object is ONLY applicable for FRSM-2T3/E3.
|
| dsx3RedSeverity |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.1 |
|
This variable is used to setup the severity of RED
alarm. So when LOS/LOF alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
LOF detection is not applicable for CESM-8T3/E3.
|
| dsx3RAISeverity |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.2 |
|
This variable is used to setup the severity of RAI
alarm. So when RAI alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
This is not applicable for CESM-T3/E3.
|
| dsx3NEAlarmUpCount |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.3 |
|
This parameter specifies the increment to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 6
and the integration counter is incremented by
this value every 10 ms while the alarm persists.
The counter is decremented by the value of
dsx3NEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds
dsx3NEAlarmThreshold an Alarm of the severity
specified for the particular NE alarm is declared.
LOF detection is not applicable for CESM-T3/E3
|
| dsx3NEAlarmDownCount |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.4 |
|
This parameter specifies the decrement to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 1 and
the integration counter is decremented by this value
every 10 ms while no alarm persists. The counter is
incremented by the value of dsx3NEAlarmUpCount
while there is no alarm (the counter does not decrement below
zero). When the integration counter reaches zero any Alarm
previously declared is removed.
LOF detection is not applicable for CESM-T3/E3
|
| dsx3NEAlarmThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.5 |
|
The value set in this object determines the value that
the alarm integration counter must reach for an near end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds.
|
| dsx3FEAlarmUpCount |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.6 |
|
This parameter specifies the increment to the
Far End alarm integration counters. The local alarms
are RAI and AIS. The Default value is 6 and the
integration counter is incremented by this value every
10 ms while the alarm persists. The counter is decremented
by the value of dsx3FEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds dsx3FEAlarmThreshold
an Alarm of the severity specified for the particular far end
alarm is declared.
This object is not applicable for CESM-T3/E3.
|
| dsx3FEAlarmDownCount |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.7 |
|
This parameter specifies the decrement to the
Far End alarm integration counters. The local alarms
are AIS and RAI. The Default value is 1. The integration
counter is decremented by this value every 10 ms
(till zero), while no alarm persists. The counter is
incremented by the value of dsx3FEAlarmUpCount
while there is no alarm. When the integration counter
decrements to zero any previously declared Alarm is removed.
This object is not applicable for CESM-T3/E3.
|
| dsx3FEAlarmThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.8 |
|
The value set in this object determines the value that
the alarm integration counter must reach for an far end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds.
This object is not applicable for CESM-T3/E3.
|
| dsx3StatisticalAlarmSeverity |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.9 |
|
This variable is used to setup the severity of
any of the Statistical alarms. So when a
Statistical Counter exceeds its specified threshold
the card will send the alarm with appropriate
severity. A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
|
| dsx3LCV15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.10 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| dsx3LCV24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.11 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| dsx3LES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.12 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| dsx3LES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.13 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| dsx3LSES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.14 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| dsx3LSES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.15 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| dsx3PCV15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.16 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.
|
| dsx3PCV24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.17 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.
|
| dsx3PES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.18 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface.
|
| dsx3PES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.19 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not supported in CESM-T3/E3
This object is not applicable for E3 interface.
|
| dsx3PSES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.20 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object does not apply to the E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3PSES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.21 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3SEFS15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.22 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3
|
| dsx3SEFS24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.23 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
This object is not supported in CESM-T3/E3
|
| dsx3AISS15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.24 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3
|
| dsx3AISS24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.25 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
This object is not supported in CESM-T3/E3
|
| dsx3UAS15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.26 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| dsx3UAS24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.27 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| dsx3E3BIP8CV15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.28 |
|
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3.
|
| dsx3E3BIP8CV24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.29 |
|
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3.
|
| dsx3E3BIP8ES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.30 |
|
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3.
|
| dsx3E3BIP8ES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.31 |
|
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
|
| dsx3E3BIP8SES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.32 |
|
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
|
| dsx3E3BIP8SES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.33 |
|
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
|
| dsx3CCV15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.34 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3CCV24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.35 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3CES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.36 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3CES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.37 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3CSES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.38 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3CSES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.1.2.1.1.39 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3.
|
| dsx3LineAlarmState |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.1 |
|
This variable is a bitmap of the DSX3 Line ALarms
on the card. A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition Alarm
----------- -----
0 Receiving RAI
1 Transmitting RAI
2 Receiving AIS
3 Transmitting AIS
4 Receiving OOF
5 Receiving LOS
6 Near End Local Loopback in effect
7 Near End Remote Loopback in effect
8 Receiving test pattern
9 Receive LCD
10 Receiving C-bit Parity pattern
|
| dsx3LineStatisticalAlarmState |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.2 |
|
This is a bitmap of the DSX3 Line Statistical
Alarms on the card. Zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
0 LCV 15 minute threshold exceeded
1 LCV 24 hour threshold exceeded
2 LES 15 minute threshold exceeded
3 LES 24 hour threshold exceeded
4 LSES 15 minute threshold exceeded
5 LSES 24 hour threshold exceeded
6 PCV 15 minute threshold exceeded
7 PCV 24 hour threshold exceeded
8 PES 15 minute threshold exceeded
9 PES 24 hour threshold exceeded
10 PSES 15 minute threshold exceeded
11 PSES 24 hour threshold exceeded
12 SEFS 15 minute threshold exceeded
13 SEFS 24 hour threshold exceeded
14 AISS 15 minute threshold exceeded
15 AISS 24 hour threshold exceeded
16 UAS 15 minute threshold exceeded
17 UAS 24 hour threshold exceeded
18 BIP8CV/G.832 15 minute threshold exceeded
19 BIP8CV/G.832 24 hour threshold exceeded
20 BIP8ES/G.832 15 minute threshold exceeded
21 BIP8ES/G.832 24 hour threshold exceeded
22 BIP8SES/G.832 15 minute threshold exceeded
23 BIP8SES/G.832 24 hour threshold exceeded
24 CCV 15 minute threshold exceeded
25 CCV 24 hour threshold exceeded
26 CES 15 minute threshold exceeded
27 CES 24 hour threshold exceeded
28 CSES 15 minute threshold exceeded
29 CSES 24 hour threshold exceeded
Bits 18 to 23 do not have any significance if the framing is
G.751(which is used in FRSM_VHS)
only bits 0,1,2,3,4,5,16 and 17 are applicable to CESM-T3/E3.
|
| dsx3LCVCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.3 |
|
The number of Line Code Violations(LCV)
encountered by the interface in current
15 minute period.
|
| dsx3LCV15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.4 |
|
The number of Line Code Violations(LCV)
encountered by the interface in current
last 15 minute period.
|
| dsx3LCV24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.5 |
|
The number of Line Code Violations(LCV)
encountered by the interface in current
last 24 hour period.
|
| dsx3LESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.6 |
|
The number of Line Errored Seconds(LES)
encountered by the interface in current
15 minute period.
|
| dsx3LES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.7 |
|
The number of Line Errored Seconds(LES)
encountered by the interface in last
15 minute period.
|
| dsx3LES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.8 |
|
The number of Line Errored Seconds(LES)
encountered by the interface in last
24 hour period.
|
| dsx3LSESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.9 |
|
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in current
15 minute period.
|
| dsx3LSES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.10 |
|
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
15 minute period.
|
| dsx3LSES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.11 |
|
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
24 hour period.
|
| dsx3PCVCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.12 |
|
The number of P-bit Coding Violations(PCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PCV15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.13 |
|
The number of P-bit Coding Violations(PCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PCV24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.14 |
|
The number of P-bit Coding Violations(PCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3PESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.15 |
|
The number of P-bit Errored Seconds(PES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.16 |
|
The number of P-bit Errored Seconds(PES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.17 |
|
The number of P-bit Errored Seconds(PES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3PSESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.18 |
|
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PSES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.19 |
|
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3PSES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.20 |
|
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3SEFSCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.21 |
|
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3SEFS15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.22 |
|
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3SEFS24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.23 |
|
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3AISSCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.24 |
|
The number of AIS Severely Errored Seconds
encountered by the interface in current 15 minute
period.
This object is not supported in CESM-T3/E3
|
| dsx3AISS15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.25 |
|
The number of AIS Severely Errored Seconds
encountered by the interface in last 15 minute
period.
This object is not supported in CESM-T3/E3
|
| dsx3AISS24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.26 |
|
The number of AIS Severely Errored Seconds
encountered by the interface in last 24 Hour
period.
This object is not supported in CESM-T3/E3
|
| dsx3UASCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.27 |
|
The number of Unavailable Seconds(UAS)
encountered by the interface in current
15 minute period.
|
| dsx3UAS15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.28 |
|
The number of Unavailable Seconds(UAS)
encountered by the interface in last
15 minute period.
|
| dsx3UAS24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.29 |
|
The number of Unavailable Seconds(UAS)
encountered by the interface in last
24 Hour period.
|
| dsx3PercentLcvEFS |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.30 |
|
This object gives the percentage of
seconds without any LCV Errors in the
total elapsed seconds.
|
| dsx3E3BIP8CVCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.31 |
|
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8CV15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.32 |
|
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8CV24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.33 |
|
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8ESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.34 |
|
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8ES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.35 |
|
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8ES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.36 |
|
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8SESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.37 |
|
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in current 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8SES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.38 |
|
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3E3BIP8SES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.39 |
|
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3
|
| dsx3LineAlarmClrButton |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.40 |
|
Setting this object to dsx3LineAlarmClear will
cause all the alarms statuses and counters to reset.
|
| dsx3CCVCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.41 |
|
The number of C-bit Coding Violations(CCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CCV15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.42 |
|
The number of C-bit Coding Violations(CCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CCV24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.43 |
|
The number of C-bit Coding Violations(CCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3CESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.44 |
|
The number of C-bit Errored Seconds(CES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.45 |
|
The number of C-bit Errored Seconds(CES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.46 |
|
The number of C-bit Errored Seconds(CES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3CSESCurrent |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.47 |
|
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in current 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CSES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.48 |
|
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 15 minute period.
This object is not supported in CESM-T3/E3
|
| dsx3CSES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.1.3.1.1.49 |
|
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 24 Hour period.
This object is not supported in CESM-T3/E3
|
| dsx3RcvLOSCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.1 |
|
The number of times the Loss of Signal was detected
with or without integrating to LOS alarm.
|
| dsx3RcvOOFCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.2 |
|
The number of times the Out of Frame was detected
with or without integrating to OOF alarm.
This object is not supported in CESM-T3/E3
|
| dsx3RAICount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.3 |
|
The number of times Yellow Alarms was detected with
or without integrating to RAI alarm.
This object is not supported in CESM-T3/E3
|
| dsx3CCVCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.4 |
|
The counter associated with the number of C Bit
Coding Violations encountered by a DS3/E3 interface.
This object is not supported in CESM-T3/E3
|
| dsx3FECount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.5 |
|
The number of Framing Pattern Errors encountered by
a DS3/E3 interface.
This object is not supported in CESM-T3/E3
|
| dsx3AtmHECCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.6 |
|
The number of Header Check Sequence(HCS) Errors.
This object is not supported in CESM-T3/E3
|
| dsx3AtmHECSecCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.7 |
|
The number of HEC errored seconds.
This object is not supported in CESM-T3/E3
|
| dsx3AtmSEHECSecCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.8 |
|
The number of Severely HEC error seconds.
This object is not supported in CESM-T3/E3
|
| dsx3CounterClrButton |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.9 |
|
This variable is used to clear all the counters.
|
| dsx3RcvPERRCounter |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.10 |
|
The number of P-bit parity error.
This object is not supported in CESM-T3/E3
|
| dsx3RcvFEBECounter |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.11 |
|
The number of Far-end block error.
This object is not supported in CESM-T3/E3
|
| dsx3RcvEXZCounter |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.12 |
|
The number of excessive zeros
This object is not supported in CESM-T3/E3
|
| dsx3LCVCount |
.1.3.6.1.4.1.351.110.4.4.1.4.1.1.13 |
|
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3 interface.
|
| dsx3PlcpNum |
.1.3.6.1.4.1.351.110.4.4.2.1.1.1.1 |
|
This object identifies the dsx3 PLCP interface.
The value of this object must be same as the value
specified in 'dsx3LineNum' object from cwDsx3ConfigTable.
|
| dsx3PlcpCellFraming |
.1.3.6.1.4.1.351.110.4.4.2.1.1.1.2 |
|
The value for this object sets the cell delineation
method used by the interface. The cell delineation
defines how a receiving device recognizes the start
and end of an ATM cell.
framingByPlcp (1): The ATM Cells are in predetermined
location within each PLCP row, so
no additional method is needed to
delineate ATM cells.
framingByAtmHec (2): The Header Error Control field of the
ATM cell header is used to delineate
ATM cells.
|
| dsx3PlcpPayloadScramble |
.1.3.6.1.4.1.351.110.4.4.2.1.1.1.3 |
|
The value for this object is used for enabling/disabling
PLCP cell scrambling.
|
| dsx3PlcpLoopCommand |
.1.3.6.1.4.1.351.110.4.4.2.1.1.1.4 |
|
specifies the type of loopback on the line.
The possible value(s) are :
noLoop (1): Not in loopback.
remoteLineLoop (2): Remote Line Loopback.
localLineLoop (3): Local Line Loopback.
|
| dsx3PlcpRedSeverity |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.1 |
|
This variable is used to setup the severity of PLCP RED
alarm. So when PLCP_OOF alarm is detected the card will
declare the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
|
| dsx3PlcpRAISeverity |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.2 |
|
This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP RAI alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
|
| dsx3PlcpLssSeverity |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.3 |
|
This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP LSS alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
|
| dsx3PlcpLssEnable |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.4 |
|
This objects specifies whether the LSS feature is
enabled/disabled.
|
| dsx3PlcpLssCodeConnected |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.5 |
|
This object derfines the value of the LSS code
that is to be interpreted as Link Connected.
|
| dsx3PlcpLssCodeRxLinkDn |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.6 |
|
This object defines the value of the LSS code
that is to be identified as Receive Link Down.
|
| dsx3PlcpLssCodeRxLinkUp |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.7 |
|
This object defines the value of the LSS code that
is to be interpreted as Receive Link Up.
|
| dsx3PlcpStatisticalAlarmSeverity |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.8 |
|
This variable sets up the severity of PLCP Statistical
alarm. So when PLCP Statistical alarm is detected, the
card will send the alarm with appropriate severity.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
|
| dsx3PlcpBip8CV15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.9 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
|
| dsx3PlcpBip8CV24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.10 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
|
| dsx3PlcpBip8ES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.11 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
|
| dsx3PlcpBip8ES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.12 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
|
| dsx3PlcpBip8SES15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.13 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
|
| dsx3PlcpBip8SES24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.14 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
|
| dsx3PlcpSEFS15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.15 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
|
| dsx3PlcpSEFS24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.16 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
|
| dsx3PlcpUAS15MinThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.17 |
|
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
|
| dsx3PlcpUAS24HrThreshold |
.1.3.6.1.4.1.351.110.4.4.2.2.1.1.18 |
|
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
|
| dsx3PlcpLineAlarmState |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.1 |
|
This variable is a bitmap of the DSX3 Line alarms.
A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition Alarm
----------- -----
0 Receiving RAI
1 Transmitting RAI
2 Receiving OOF
3 Receiving LSS Link Up
4 Transmitting LSS Link Up
5 Receiving LSS Link Down
6 Transmitting LSS Link Down
7 Near End Local Loopback in effect
8 Near End Remote Loopback in effect
|
| dsx3PlcpLineStatisticalAlarmState |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.2 |
|
This variable is a bitmap of the DSX3 Line Statictical
Alarms on the card. A value of zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
0 Bip8CV 15 minute threshold exceeded
1 Bip8CV 24 hour threshold exceeded
2 Bip8ES 15 minute threshold exceeded
3 Bip8ES 24 hour threshold exceeded
4 Bip8SES 15 minute threshold exceeded
5 Bip8SES 24 hour threshold exceeded
6 Plcp SEFS 15 minute threshold exceeded
7 Plcp SEFS 24 hour threshold exceeded
8 Plcp UAS 15 minute threshold exceeded
9 Plcp UAS 24 hour threshold exceeded
|
| dsx3PlcpBip8CVCurrent |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.3 |
|
This counter counts the number of
BIP-8 code violations encountered by the interface.
|
| dsx3PlcpBip8CV15MinBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.4 |
|
The counter associated with the number of
BIP-8 code violations in the last 15 minute period
encountered by the interface.
|
| dsx3PlcpBip8CV24HrBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.5 |
|
The counter associated with the number of
BIP-8 code violations in the last 24 hour period
encountered by the interface.
|
| dsx3PlcpBip8ESCurrent |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.6 |
|
This counter counts the number of
BIP-8 code violations Errored Seconds
encountered by the interface.
|
| dsx3PlcpBip8ES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.7 |
|
This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 15 minutes encountered by the interface.
|
| dsx3PlcpBip8ES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.8 |
|
This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 24 hours encountered by the interface.
|
| dsx3PlcpBip8SESCurrent |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.9 |
|
This counter counts the number of
Bip8 code violations Severely Errored Seconds
encountered by the interface.
|
| dsx3PlcpBip8SES15MinBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.10 |
|
This counter counts the number of
BIP-8 Severely Errored Seconds in the last
15 minutes encountered by the interface.
|
| dsx3PlcpBip8SES24HrBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.11 |
|
This counter counts the number of
BIP-8 Severely Errored Seconds in the last
24 hours encountered by the interface.
|
| dsx3PlcpSEFSCurrent |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.12 |
|
This counter counts the number of
Severely Errored Framing Seconds
encountered by the interface.
|
| dsx3PlcpSEFS15MinBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.13 |
|
This counter counts the number of
Severely Errored Framing Seconds in the last
15 minutes encountered by the interface.
|
| dsx3PlcpSEFS24HrBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.14 |
|
This counter counts the number of
Severely Errored Framing Seconds in the last
24 hours encountered by the interface.
|
| dsx3PlcpUASCurrent |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.15 |
|
This counter counts the number of
Unavailable Seconds encountered by the interface.
|
| dsx3PlcpUAS15MinBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.16 |
|
This counter counts the number of
Unavailable Seconds in the last 15 minutes
encountered by the interface.
|
| dsx3PlcpUAS24HrBucket |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.17 |
|
This counter counts the number of
Unavailable Seconds in the last 24 hours
encountered by the interface.
|
| dsx3PlcpAlarmClrButton |
.1.3.6.1.4.1.351.110.4.4.2.3.1.1.18 |
|
This variable is used to clear all the alarms.
|
| dsx3PlcpRcvBip8Count |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.1 |
|
The number of BIP-8 errors encountered by
the interface.
|
| dsx3PlcpRcvOOFCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.2 |
|
The number of times the Out of Frame(OOF) was detected
with or without integrating to OOF alarm.
|
| dsx3PlcpRcvRAICount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.3 |
|
The number of times Remote Alarm Indication(RAI)
was detected with or without integrating to RAI alarm.
|
| dsx3PlcpFECount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.4 |
|
The number of Framing Errors detected.
|
| dsx3PlcpFESecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.5 |
|
The number of Framing Error errored seconds.
|
| dsx3PlcpSEFESecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.6 |
|
The number of Severely errored Framing error seconds.
|
| dsx3PlcpFEBECount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.7 |
|
The number of Far End Block Errors(FEBE) detected.
|
| dsx3PlcpFEBESecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.8 |
|
The number of FEBE errored seconds.
|
| dsx3PlcpSEFEBESecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.9 |
|
The number of Severely errored FEBE seconds.
|
| dsx3PlcpHECCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.10 |
|
The number of HCS Errors.
|
| dsx3PlcpHECSecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.11 |
|
The number of HEC errored seconds.
|
| dsx3PlcpSEHECSecCount |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.12 |
|
The number of Severely HEC error seconds.
|
| dsx3PlcpCounterClrButton |
.1.3.6.1.4.1.351.110.4.4.2.4.1.1.13 |
|
This variable is used to clear all the counters.
|
