CISCO-MGX82XX-RPM-SUBIF-MIB.mib object view, vendor Stratacom
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2024 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2024 can import MIB file CISCO-MGX82XX-RPM-SUBIF-MIB and use it to monitor vendor specific OID's.
CISCO-MGX82XX-RPM-SUBIF-MIB file content
Object view of CISCO-MGX82XX-RPM-SUBIF-MIB:
| Scalar Object |
| rpmPortEntry |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1 |
|
An entry for the RPM backplane sub interface.
Each entry contains RPM's backplane sub interface number,
its IP address and ATM address.
|
| Tabular Object |
| rpmPortSlotNum |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.1 |
|
This object specifies the the slot number
of the RPM card in MGX shelf.
|
| rpmPortSubInterface |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.3 |
|
This object identifies the sub-interface number.
The value 0 is for the sub-interface on the
main interface(rpmPortInterface).
|
| rpmPortInterface |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.2 |
|
This is the RPM's backplane interface.
Currently there is only one interface and
hence only supported value is 1.
|
| rpmPortRowStatus |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.4 |
|
This indicates the status of this subinterface.
add(1) : sub-interface is added.
del(2) : sub-interface is deleted.
mod(3) : Set to this value before modifying objects
related to Subinterfaces.
|
| rpmPortIpAddress |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.5 |
|
IP address configured on the sub-interface.
|
| rpmPortSubNetMask |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.6 |
|
The subnet mask configured on the sub-interface.
|
| rpmPortState |
.1.3.6.1.4.1.351.110.5.2.9.1.1.1.7 |
|
This indicates the state of this sub-interface.
notConfigured(1) : Sub-interface is not configured.
active(2) : Sub-interface is in active state.
failed(3) : Sub-interface is in failed state.
|
| Table |
| rpmPortTable |
.1.3.6.1.4.1.351.110.5.2.9.1.1 |
|
This table contains information on subinterfaces
configured on RPM back plane interface.
|
| Object Identifier |
| ciscoMgx82xxRpmSubIfMIB |
.1.3.6.1.4.1.351.150.60 |
|
This MIB is used to provision backplane sub-interfaces
on the MGX's Route Processor Module (RPM). This MIB is
implemented on the MGX controller to manage the RPM. The RPM
family of Router Modules run the IOS Operating System
|
| cmrSubIfMIBConformance |
.1.3.6.1.4.1.351.150.60.2 |
| cmrSubIfMIBCompliances |
.1.3.6.1.4.1.351.150.60.2.1 |
| cmrSubIfMIBGroups |
.1.3.6.1.4.1.351.150.60.2.2 |
| Group |
| cmrSubIfMIBGroup |
.1.3.6.1.4.1.351.150.60.2.2.1 |
|
Objects related to ATM Subinterface in RPM module.
|
