| cesCntChanNum |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.1 |
|
This object identifies the channel number of the
CESM channel. The value for this object is same as
the value specified in 'cesCnfChanNum'.
|
| cesChanState |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.2 |
|
This object indicates the channel/connection status.
The possible value(s) are :
notConfigured (1) : Channel is not configured
okay (2) : channel is ok
alarm (3) : channel is in alarm.
The connection segment is not broken.
failed (4) : channel is failed.
The connection segment is broken.
This value is applicable when
PXM running PNNI Control Software.
|
| cesXmtATMState |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.3 |
|
This object indicates the transmit state of channel
on the ATM side (towards the network).
The possible value(s) are :
other(1) : values other than mentioned below.
normal(2) : Channel is ok.
sendingAIS(3) : Sending AIS signal
sendingFERF(4): Sending FERF.
|
| cesRcvATMState |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.4 |
|
This variable indicates the receive state of channel
on the ATM side (from the network).
The possible value(s) are :
other(1) : values other than mentioned below.
normal(2) : Channel is ok.
receivingAIS (3) : receiving AIS signal
receivingFERF(4) : receiving FERF.
|
| cesCellLossStatus |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.5 |
|
When cells are lost for the CellLossIntegrationPeriod the value
is set to loss ( 2). when cells are no longer lost, the value is
set to noLoss(1).
|
| cesReassCells |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.6 |
|
The number of cells played out to T1/E1/T3E3 interface. It
excludes cells that were discarded for any reason.
|
| cesGenCells |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.7 |
|
The number of cells generated from T1/E1/T3E3 interface
and sent towards network.
|
| cesHdrErrors |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.8 |
|
The number of AAL-1 header errors detected and possibly
corrected. Header errors include correctable and uncor-
rectable CRC, plus bad parity.
|
| cesPointerReframes |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.9 |
|
The number of events in which the AAL1 reassembler found
that an SDT pointer is not where it is expected and the
and the pointer must be reacquired.
Not supported in CESM-8P due to limitation in AAL1 SAR.
Not applicable for CESM-4T1/E1 and CESM-T3/E3
|
| cesLostCells |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.10 |
|
The number of cells lost in egress direction due to
AAL 1 header errors and missing cells.
|
| cesBufUnderflows |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.11 |
|
The number of buffer underflows in Egress direction
Not supported in CESM-8P due limitation in AAL1 SAR.
|
| cesBufOverflows |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.12 |
|
The number of buffer overflows in Egress direction
Not supported in CESM-8P due to limitation in AAL1 SAR.
|
| cesIngrDiscardedBytes |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.13 |
|
The number of bytes discarded due to shelf alarm in ingress
direction from port data.
Not supported in CESM-8P.
|
| cesUflowInsCells |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.14 |
|
The number of All 1's cells inserted in case of Egress Buffer
Underflow Not supported in CESM-8P.
|
| cesOflowDropBytes |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.15 |
|
The number of bytes discarded in Egress direction because of
Egress buffer overflow
Not supported in CESM-8P.
|
| cesCellSeqMismatchCnt |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.16 |
|
The number of times SAR received a valid out of sequence
AAL-1 cell from CellBus.
|
| counterClrButton |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.17 |
|
This object is used for clearing the counters
in this table.
If set to resetCounters(2), then counters will be
cleared.
|
| cesChanSecUptime |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.18 |
|
The number of seconds channel is in service
This object is only applicable for CESM-8P.
|
| cesChanSignalingStatus |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.19 |
|
This variable indicates the connection signalling status
Connection will be in Idle suppression mode if it in on-hook.
Not applicable for T3E3 and CESM-4P.
|
| cesChanStatusBitMap |
.1.3.6.1.4.1.351.110.5.3.2.2.1.1.20 |
|
This variable indicates the consolidated bit
map of the channel alarm state.
Individual bit positions are as defined below.
Bit position Fail/Alarm Reason
------------ ---------- ------
0 Alarm Reserved
1 Alarm n/w side AIS/RDI Rx
2 Fail Conditioned(A bit from n/w)
3 Alarm Reserved
4 Fail Reserved
5 Fail Reserved
6 Alarm Reserved
7 Alarm Cell loss alarm
Fail bitmap mask : 0x34
Alarm bitmap mask: 0xCB
This object is not applicable to MGX Release 1.x.
|
