CISCO-WAN-FEEDER-MIB.mib object view, vendor Stratacom
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2024 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2024 can import MIB file CISCO-WAN-FEEDER-MIB and use it to monitor vendor specific OID's.
CISCO-WAN-FEEDER-MIB file content
Object view of CISCO-WAN-FEEDER-MIB:
| Scalar Object |
| cwfFeederEntry |
.1.3.6.1.4.1.351.150.15.1.1.1.1 |
|
An entry in cwfFeederTable.
|
| Tabular Object |
| cwfFeederIfNum |
.1.3.6.1.4.1.351.150.15.1.1.1.1.1 |
|
This is an unique interface number of an
ATM virtual interface. The value of this
object is equal to the ifIndex of the ATM
virtual interface interface identified by
ifType atmVirtual(149).
|
| cwfFeederName |
.1.3.6.1.4.1.351.150.15.1.1.1.1.2 |
|
This is the name of the feeder. It contains
a string of length zero, if the feeder name
is not available.
|
| cwfLanIP |
.1.3.6.1.4.1.351.150.15.1.1.1.1.3 |
|
This is the LAN IP address of the feeder.
This IP address is used for ethernet interface.
|
| cwfNetIP |
.1.3.6.1.4.1.351.150.15.1.1.1.1.4 |
|
This is the network IP address of the feeder.
This IP address is used for ATM interface.
|
| cwfRemoteShelf |
.1.3.6.1.4.1.351.150.15.1.1.1.1.5 |
|
This is the remote shelf number of the feeder
module.
|
| cwfRemoteSlot |
.1.3.6.1.4.1.351.150.15.1.1.1.1.6 |
|
This is the remote slot number of the feeder
module.
|
| cwfRemotePort |
.1.3.6.1.4.1.351.150.15.1.1.1.1.7 |
|
This is the remote physical port(line)
number of the feeder module.
|
| cwfFeederType |
.1.3.6.1.4.1.351.150.15.1.1.1.1.8 |
|
This identifies the feeeder type. fdrNON(12)
is applicable when cwfLMIType is xLMI(2).
Other values are applicable for cwfLMIType = feeder(1).
The possible values are:
fdrIPX -- Feeder is an IPX node in a routing network
fdrBPX -- Feeder is an BPX node in a routing network
fdrIpxAF -- Feeder is a stand-alone IPX node
fdrBASIS -- Feeder is a stand-alone BASIS node
fdrUNKNOWN -- Feeder is unknown
fdrUNI -- Feeder is a UNI AIT (phase 0)
fdrAPS -- Feeder is an APS (Adjunct Processor Shelf)
fdrIGX -- Feeder is an IGX node in a routing network
fdrIgxAF -- Feeder is a stand-alone IGX node
fdrVSI -- Feeder is an VSI Controller
fdrPAR -- Feeder is a PAR
fdrNON -- Non-feeder type
|
| cwfModelNumber |
.1.3.6.1.4.1.351.150.15.1.1.1.1.9 |
|
This identifies the feeder model number.
|
| cwfLMIAdminStatus |
.1.3.6.1.4.1.351.150.15.1.1.1.1.10 |
|
This provides the feeder LMI admin state
configuration capabilities for the desired
state of interface. The value of this object
is ignored during row creation.
|
| cwfLMIOperStatus |
.1.3.6.1.4.1.351.150.15.1.1.1.1.11 |
|
This provides the operational state of
the LMI connection.
|
| cwfFeederNodeAlarm |
.1.3.6.1.4.1.351.150.15.1.1.1.1.12 |
|
This identifies the feeder node alarm status.
It provides the alarm status in hierarchical order
where by if there are no feeder node alarms, it is
signified by <clear>. If minor alarms, with no major
alarms, it is signified by <minor>. If the node
has one or more major alarms, irrespective of the
minor alarm status, then it is signified by <major>.
|
| cwfFeederRowStatus |
.1.3.6.1.4.1.351.150.15.1.1.1.1.13 |
|
This is used for adding or deleting a feeder entry.
The row can be created by setting this object to
'createAndGo(4)'. The row can be deleted by setting
this object to 'destroy(6)'.
No other values are supported.
|
| cwfLMIType |
.1.3.6.1.4.1.351.150.15.1.1.1.1.14 |
|
This identifies the LMI type. It identifies the
type of network to which the LMI port is connected
to.
|
| Table |
| cwfFeederTable |
.1.3.6.1.4.1.351.150.15.1.1.1 |
|
This table contains the entries for the feeders.
It is used for addition or deletion of feeders and
to support LMI on the feeders. The information in
these entries are advertised to LMI using a system
dependent implementation when an entry is
created/activated. This table can also be applicable
to XLMI.
|
| Object Identifier |
| ciscoWanFeederMIB |
.1.3.6.1.4.1.351.150.15 |
|
This MIB is used for configuring a port on an ATM
switch module to be aware of feeder connection
information.
Terminology:
AR - Auto Route, a CISCO proprietary feature,
provides connection management for network with only
CISCO nodes such as BPX or IGX.
Feeder - An external ATM switch, which does not
have PNNI feature, connected to an ATM switch
that supports PNNI to provide LMI.
LMI - Local Management Interface is an
interface to provide a set of enhancements to
Frame Relay specification for managing complex
internetworks. LMI extensions include global
addressing, virtual-circuit status messages,
and multicasting.
XLMI - The Extended LMI is a type of LMI which
is implemented in an AR + PNNI network.
|
| cwfMIBObjects |
.1.3.6.1.4.1.351.150.15.1 |
| cwfFeeder |
.1.3.6.1.4.1.351.150.15.1.1 |
| cwfMIBConformance |
.1.3.6.1.4.1.351.150.15.3 |
| cwfMIBCompliances |
.1.3.6.1.4.1.351.150.15.3.1 |
| cwfMIBGroups |
.1.3.6.1.4.1.351.150.15.3.2 |
| Group |
| cwfFeederGroup |
.1.3.6.1.4.1.351.150.15.3.2.1 |
|
The objects related to configuring a feeder.
|
| cwfFeederGroup2 |
.1.3.6.1.4.1.351.150.15.3.2.2 |
|
The objects related to configuring feeder and
non-feeder(XLMI).
|
