| parSnNodeId |
.1.3.6.1.4.1.351.130.1.1 |
|
This object specifies the node number of the node.
When the network manager tries to modify the value of
this object, a message is sent node state machine which
propagates this information and the value gets modified
only if the new node number is successfully propagated.
The node number uniquely identifies a routing node
in a network.
|
| parSnNodeIP |
.1.3.6.1.4.1.351.130.1.2 |
|
This object specifies the IP address for
routing node and is used for communication with
SNMP manager(for example Cisco Wan Manager:CWM).
|
| parSnNodeName |
.1.3.6.1.4.1.351.130.1.3 |
|
This object specifies the name of the node
and is unique among all the nodes in the network.
Whenever the name of the node is changed, AutoRoute
has to propagate the information to the other nodes
in the network. It also specifies the name of a PAR
Feeder node.
|
| parSnRevision |
.1.3.6.1.4.1.351.130.1.4 |
|
This object specifies the primary revision of
the PAR running on the node.
Format: cc.c.cc
Where: c = one ascii character
|
| parSnNodeAlarmStatus |
.1.3.6.1.4.1.351.130.1.5 |
|
This object specifies the type of alarm on the node.
clear(1) : No Alarm
minor(2) : Minor Alarm
major(3) : Major Alarm
unreach(4) : Node is unreachable.
|
| parSnNumberOfTrunks |
.1.3.6.1.4.1.351.130.1.6 |
|
This object specifies the number of trunks
attached to the node.
|
| parIfEntry |
.1.3.6.1.4.1.351.130.2.1.1 |
|
Entries for logical interfaces.
|
| parTrkEntry |
.1.3.6.1.4.1.351.130.2.2.1 |
|
Entries for logical interfaces configured
as trunks (parIfType nni).
|
| parTrkLoadEntry |
.1.3.6.1.4.1.351.130.2.3.1 |
|
Load info for logical interfaces configured as
trunks (parIfType nni).
|
| parConnectionEntry |
.1.3.6.1.4.1.351.130.3.1.1 |
|
Entries for connections mastered or slaved
by the node. Each entry contains Local and
remote end information.
|
| parClockEntry |
.1.3.6.1.4.1.351.130.4.1.1 |
|
Each entry represent a clock source available to
PAR
|
| parCmParmsMaxRoutingBundle |
.1.3.6.1.4.1.351.130.5.2.1 |
|
This object specifies the maximum number of
connections that can be routed in one routing cycle.
|
| parCmParmsRerouteTimer |
.1.3.6.1.4.1.351.130.5.2.2 |
|
This object specifies the minimum time after
which a connection is routed once it has been
successfully routed.
|
| parCmParmsResetTimer |
.1.3.6.1.4.1.351.130.5.2.3 |
|
This object specifies whether the reroute timer
should be reset if the path for routed connection
failed. If the value of the object is true(1), the
timer is reset on detecting path fail.
|
| parCmParmsDnUpPerPass |
.1.3.6.1.4.1.351.130.5.2.4 |
|
This object specifies the maximum number of
connections that are upped or down in one schedule
of down connection state machine.
|
| parCmParmsDnUpTimer |
.1.3.6.1.4.1.351.130.5.2.5 |
|
This object specifies the minimum time interval
(in milliseconds) between two schedules of the down
connection state machine.
|
| parCmParmsRrtErrsPerCycle |
.1.3.6.1.4.1.351.130.5.2.6 |
|
This object specifies the threshold for number
of failures to route a connection before it is
moved into the wait group. If the value of this
object is zero, the feature is disabled.
|
| parCmParmsRrtCycleInterval |
.1.3.6.1.4.1.351.130.5.2.7 |
|
This object specifies the time (in minutes) for
which no attempt is made to route a connection in
the wait group.
|
| parCmParmsMaxRrtCycles |
.1.3.6.1.4.1.351.130.5.2.8 |
|
This object specifies the number of times a
connection is added to the wait group before
declaring it unroutable.
|
| parCmParmsRrtPauseTime |
.1.3.6.1.4.1.351.130.5.2.9 |
|
This object specifies the time interval
(in milliseconds) between two routing cycles.
|
| parCmParmsMaxUpdates |
.1.3.6.1.4.1.351.130.5.2.10 |
|
This object specifies the maximum number of
connection management updates that are sent by
the node in schedule..
|
| parCmParmsRerouteGroups |
.1.3.6.1.4.1.351.130.5.2.11 |
|
This object specifies the total number of
reroute groups.
|
| parCmParmsMinRrGroupSize |
.1.3.6.1.4.1.351.130.5.2.12 |
|
This object specifies the minimum size of
reroute group in Cell Load Units.
|
| parCmParmsRrGroupInc |
.1.3.6.1.4.1.351.130.5.2.13 |
|
This object specifies the increment of
reroute group size (in Cell Load Units)
between adjacent groups.
|
| parCmParmsCostBased |
.1.3.6.1.4.1.351.130.5.2.14 |
|
This object can be configured to enable
or disable cost based routing feature.
If the value of this object is true(1),
the feature is enabled else it is disabled.
|
| parCmParmsUseCache |
.1.3.6.1.4.1.351.130.5.2.15 |
|
This object can be configured to enable or disable
hop based route selection from using cache of
precomputed routes.
If the value of this object is true(1), the feature is
enabled else it is disabled.
|
| parCmParmsUseDelay |
.1.3.6.1.4.1.351.130.5.2.16 |
|
This object can be configured to enable
or disable cost based route selection from
considering end-to-end delay associated with
the routes. If the value of this object is true(1),
the delay would be considered otherwise daley would
not be considered during routing of connection.
|
| parCmParmMaxViaCons |
.1.3.6.1.4.1.351.130.5.2.17 |
|
This object specifies the maximum number of
via user connections that can be routed through
the node.
|
| parMnUpdtInterval |
.1.3.6.1.4.1.351.130.5.3.1 |
|
This object specifies the timer interval
(in seconds) for the current update state machine.
|
| parMnUpdtNodesPerInt |
.1.3.6.1.4.1.351.130.5.3.2 |
|
This object specifies the maximum number of
nodes to which current updates can be sent per
interval.
|
| parMnUpdtBatchSend |
.1.3.6.1.4.1.351.130.5.3.3 |
|
This object specifies whether current updates
to any node are sent one at a time or all in one go.
If the value of this object is true(1), all current
updates are sent to the node simultaneously.
If the value of this object is False, current updates
are sent one at a time.
|
| parSwFuncAbrVsvd |
.1.3.6.1.4.1.351.130.5.4.1 |
|
This object enables/disables the ABR standard
with VSVD. The feature is enabled if the value
of the object is true(1).
|
| parSwFuncNodeType |
.1.3.6.1.4.1.351.130.5.4.2 |
|
This object specifies whether the node is a
routing node or a feeder node. To configure the
node from a routing(1) node to feeder(2) node
the node should be part of a single node network.
To configure the node from feeder node to routing
node, there should be no feeder trunk attached to
the node.
|
| parOnOffBackgroundUpdt |
.1.3.6.1.4.1.351.130.5.5.1 |
|
This object can be used to enable or disable
Background updates. If the value of the object
is true(1), background updates are enabled;
otherwise they are disabled.
|
| parOnOffDynamicBwAlloc |
.1.3.6.1.4.1.351.130.5.5.2 |
|
This object can be used to enable or disable
Bandwidth state machine. If the value of the
object is true(1), bandwidth state machine is
enabled; otherwise it is disabled.
|
| parOnOffCmUpdts |
.1.3.6.1.4.1.351.130.5.5.3 |
|
This object can be used to enable or disable
connection management updates. If the value of
the object is true(1), connection management
updates are enabled; otherwise they are disabled.
|
| parOnOffRouting |
.1.3.6.1.4.1.351.130.5.5.4 |
|
This object can be used to enable or disable
connection routing. If the value of the object
is true(1), routing is enabled; otherwise it
is disabled.
|
| parOnOffCommFailTest |
.1.3.6.1.4.1.351.130.5.5.5 |
|
This object can be used to enable or disable
Comm Fail Test. If the value of the object is
true(1), Comm Fail test is enabled; otherwise it
is disabled.
|
| parOnOffDrtDelay |
.1.3.6.1.4.1.351.130.5.5.6 |
|
This object can be used to enable or disable
Deroute Delay feature. If the value of the object
is true(1) Derote delay feature is enabled;
otherwise it is disabled.
|
| parOnOffRenumRec |
.1.3.6.1.4.1.351.130.5.5.7 |
|
This object can be used to enable or disable
Renumber recovery feature. If the value of the
object is true(1), renumber recovery feature is
enabled; otherwise it is disabled.
|
| parOnOffCommBreak |
.1.3.6.1.4.1.351.130.5.5.8 |
|
This object can be used to enable or disable
Comm Break Test. If the value of the object is
true(1), Comm Break Test feature is enabled;
otherwise it is disabled.
|
| parSysParmsTsPacketAge |
.1.3.6.1.4.1.351.130.5.6.1 |
|
Time Stamped packets older than this value
(in milliseconds)are discarded.
This is a network wide parameter.
|
| parSysParmsConnFail |
.1.3.6.1.4.1.351.130.5.6.2 |
|
This object specifies whether the connections to
a node should be failed when comm fail is declared
with the node. If the value of this object is true(1),
the connection will be failed.
This is a network wide parameter.
|
| parSysParmsVcPollRate |
.1.3.6.1.4.1.351.130.5.6.3 |
|
This object specifies the rate at which
VC statistics are to be polled. This is a
network wide parameter. For Portable AutoRoute
statistic collections would be done by platform
software.
|
| parSysParmsMaxVDelay |
.1.3.6.1.4.1.351.130.5.6.4 |
|
This object specifies the maximum delay for
voice connection with VAD enabled in milli-seconds.
This is a network wide parameter.
|
| parSysParmsMaxCDelay |
.1.3.6.1.4.1.351.130.5.6.5 |
|
This object specifies the maximum delay for
ADPCM compressed voice connection with VAD
enabled in milli-seconds.
This is a network wide parameter.
|
| parSysParmsMaxDDelay |
.1.3.6.1.4.1.351.130.5.6.6 |
|
This object specifies the maximum delay for
data connection in milli-seconds.
This is a network wide parameter.
|
| parSysParmsMaxADelay |
.1.3.6.1.4.1.351.130.5.6.7 |
|
This object specifies the maximum delay for
ADPCM compressed voice connection in
milli-seconds.
This is a network wide parameter.
|
| parSysParmsMaxHsdDelay |
.1.3.6.1.4.1.351.130.5.6.8 |
|
This object specifies the maximum delay for
High Speed data connection in milli-seconds.
This is a network wide parameter.
|
| parSysParmsDeEnable |
.1.3.6.1.4.1.351.130.5.6.9 |
|
This object specifies whether DE bit of
Frame Relay frames can be modified.
DE bit can be modified if the value of this
object is true(1).
This is a network wide parameter.
|
| parSysParmsFrStandard |
.1.3.6.1.4.1.351.130.5.6.10 |
|
This object specifies whether standard
Frame Relay parameters,Be and Bc, are to be used.
If the value of this object is true(1),
standard parameters are used.
This is a network wide parameter.
|
| parSysParmsDrtDelay |
.1.3.6.1.4.1.351.130.5.6.11 |
|
This object specifies whether Deroute Delay
feature is enabled. If the value of this object
is true(1), the feature is enabled.
This is a network wide parameter.
|
| parSysParmsInvLogAlarmThres |
.1.3.6.1.4.1.351.130.5.6.12 |
|
This object specifies the threshold for invalid
login attempts before triggering an alarm.
If the value of this object is zero, this feature
is disabled.
This is a network wide parameter.
|
| parSysParmsMaxCdpVDelay |
.1.3.6.1.4.1.351.130.5.6.13 |
|
This object specifies the maximum network delay
for CDP to CDP voice connection with VAD enabled
in milli-seconds.
This is a network wide parameter.
|
| parSysParmsMaxCdpCDelay |
.1.3.6.1.4.1.351.130.5.6.14 |
|
This object specifies the maximum network delay
for CDP to CDP ADPCM compressed voice connection
with VAD enabled.
This is a network wide parameter.
|
| parSysParmsMaxCdpDDelay |
.1.3.6.1.4.1.351.130.5.6.15 |
|
This object specifies the maximum network delay
for CDP to CDP data connection.
This is a network wide parameter.
|
| parSysParmsMaxCdpADelay |
.1.3.6.1.4.1.351.130.5.6.16 |
|
This object specifies the maximum network delay
for CDP to CDP ADPCM compressed voice connection.
This is a network wide parameter.
|
| parSysParmsMaxCdpHsdDelay |
.1.3.6.1.4.1.351.130.5.6.17 |
|
This object specifies the maximum network delay
for CDP to CDP High Speed data connection.
This is a network wide parameter.
|
| parSysParmsMaxIpcdpVDelay |
.1.3.6.1.4.1.351.130.5.6.18 |
|
This object specifies the maximum local delay
for CDP to CDP voice connection with VAD enabled.
This is a network wide parameter.
|
| parSysParmsMaxIpcdpCDelay |
.1.3.6.1.4.1.351.130.5.6.19 |
|
This object specifies the maximum local delay
for CDP to CDP ADPCM compressed voice connection
with VAD enabled.
This is a network wide parameter.
|
| parSysParmsMaxIpcdpDDelay |
.1.3.6.1.4.1.351.130.5.6.20 |
|
This object specifies the maximum local delay
for CDP to CDP data connection.
This is a network wide parameter.
|
| parSysParmsMaxIpcdpADelay |
.1.3.6.1.4.1.351.130.5.6.21 |
|
This object specifies the maximum local delay
for CDP to CDP ADPCM compressed voice connection.
This is a network wide parameter.
|
| parSysParmsMaxIpcdpHsdDelay |
.1.3.6.1.4.1.351.130.5.6.22 |
|
This object specifies the maximum local delay
for CDP to CDP High Speed data connection.
This is a network wide parameter.
|
| parSysParmsMaxIphsdDelay |
.1.3.6.1.4.1.351.130.5.6.23 |
|
This object specifies the maximum local delay
for High Speed data connection.
This is a network wide parameter.
|
| parSysParmsFpdDeJitter |
.1.3.6.1.4.1.351.130.5.6.24 |
|
This object specifies the jitter delay for
Fast Pad.
This is a network wide parameter.
|
| parNetParmCondInitialStgr |
.1.3.6.1.4.1.351.130.5.7.1 |
|
This object specifies the initial pause time
(in milliseconds) per new node added on addition
of node(s) in the network before initiating
conditional updates.
|
| parNetParmCondPerNodeInterval |
.1.3.6.1.4.1.351.130.5.7.2 |
|
This object specifies the minimum interval
(in milliseconds) between sending of conditional
updates to any two nodes.
|
| parNetParmCbDelay |
.1.3.6.1.4.1.351.130.5.7.3 |
|
This object specifies the minimum interval
(in milliseconds) between initiating comm break
tests between any two nodes.
|
| parNetParmCbOffset |
.1.3.6.1.4.1.351.130.5.7.4 |
|
Offset for CB.
|
| parNetParmMsgTimeout |
.1.3.6.1.4.1.351.130.5.7.5 |
|
This object specifies the timeout (in milliseconds)
for acknowledgment for control plane message sent to
another node.
|
| parNetParmMsgMaxTimeout |
.1.3.6.1.4.1.351.130.5.7.6 |
|
This object specifies the maximum number of
times a network handler timeout waiting for
acknowledgment for control plane message sent
to another node reachable through all
terrestrial trunks.
|
| parNetParmMsgMaxTimeoutSat |
.1.3.6.1.4.1.351.130.5.7.7 |
|
This object specifies the maximum number of
times a network handler timeout waiting for
acknowledgment for control plane message sent
to another node reachable through all
satellite trunks.
|
| parNetParmBlindMaxTimeout |
.1.3.6.1.4.1.351.130.5.7.8 |
|
This object specifies the maximum number of
times a network handler timeout waiting for
acknowledgment for control plane blind message
sent to another node.
|
| parNetParmCbMaxTimeout |
.1.3.6.1.4.1.351.130.5.7.9 |
|
This object specifies the maximum number of
times a network handler timeout waiting for
acknowledgment for comm break test message sent
to another node.
|
| parNetParmCfTestInterval |
.1.3.6.1.4.1.351.130.5.7.10 |
|
This object specifies the minimum time interval
between the comm fail tests for a trunk.
|
| parNetParmCfTestMultiplier |
.1.3.6.1.4.1.351.130.5.7.11 |
|
This object specifies the multiplier for the
comm fail test interval for good trunks, that is,
trunks not in comm fail.
|
| parNetParmNetwWindowSz |
.1.3.6.1.4.1.351.130.5.7.12 |
|
This object specifies the window size for the
network handler for messages to any node.
That is, the number of messages that the network
handler can send simultaneous to a node without
receiving the acknowledgment for them.
|
| parNetParmNetwLetWait |
.1.3.6.1.4.1.351.130.5.7.13 |
|
This object specifies the maximum interval
(in milliseconds) network handler waits for
the letter (message) from the processes running
on its nodes before checking the received cells.
|
| parNetParmCfDelay |
.1.3.6.1.4.1.351.130.5.7.14 |
|
TBD (in milliseconds).
|
| parNetParmHighTxRate |
.1.3.6.1.4.1.351.130.5.7.15 |
|
This object specifies the rate
(in fast packets per second) at which the
network handler sends control plane message cells
to high performance nodes
(High performance node are BPX and MGX).
|
| parNetParmLowTxRate |
.1.3.6.1.4.1.351.130.5.7.16 |
|
This object specifies the rate
(in fast packets per second) at which the
network handler sends control plane message cells to
low capacity nodes (Low capacity node are IPX and IGX).
|
| parNetParmMaxNodeBlks |
.1.3.6.1.4.1.351.130.5.7.17 |
|
This object specifies the maximum number of blocks
of size 256 bytes, that should be queued up for
transmission to a node.
|
| parNetParmTopoMsgSegSz |
.1.3.6.1.4.1.351.130.5.7.18 |
|
This object specifies the maximum size (in bytes)
of the segment into which the topology message,
sent during network join, is divided.
|
| parIfLogicalInterface |
.1.3.6.1.4.1.351.130.2.1.1.1 |
|
This object specifies the logical interface number.
|
| parIfType |
.1.3.6.1.4.1.351.130.2.1.1.2 |
|
This object specifies the type of interface.
User ports need to be UNI interface. The trunks
can be either UNI or NNI.
userport(1) : UNI interface. This is for user ports.
routingtrunk(2) : NNI interface. This value can be
set provided there are no connections
on the interface.
feedertrunk(3) : It is feeder trunk.
clkport(4) : Clock port.
virtualtrunk(5): Virtual Trunk.
Type of interface can be changed from nni(2) to uni(1)
if the trunk is not added.
|
| parIfOperStatus |
.1.3.6.1.4.1.351.130.2.1.1.3 |
|
This object specifies the operation status of
the interface.
up(1) : Interface is up.
This value is applicable for UNI as well as NNI
interfaces.
added(2) : Interface is added.
This value is applicable for NNI interfaces.
failed(3) : Interface is failed.
This value is applicable for UNI as well as NNI
interfaces.
added-failed (4) : Interface is failed.
This value is applicable for NNI interfaces.
interfaces.
|
| parIfTxBw |
.1.3.6.1.4.1.351.130.2.1.1.4 |
|
This object specifies the transmit bandwidth
for the interface.
|
| parIfRxBw |
.1.3.6.1.4.1.351.130.2.1.1.5 |
|
This object specifies the receive bandwidth for
the interface.
|
| parIfMaxConn |
.1.3.6.1.4.1.351.130.2.1.1.6 |
|
This object specifies the maximum number
of connections that can be configured over
the interface.
|
| parIfHiAddrMin |
.1.3.6.1.4.1.351.130.2.1.1.7 |
|
This object specifies the minimum VPI that
PAR can use for configuring connection in
the interface.
|
| parIfHiAddrMax |
.1.3.6.1.4.1.351.130.2.1.1.8 |
|
This object specifies the maximum VPI that
PAR can use for configuring connection in
the interface.
|
| parIfLoAddrMin |
.1.3.6.1.4.1.351.130.2.1.1.9 |
|
This object specifies the minimum VCI that
PAR can use for configuring connection in
the interface.
|
| parIfLoAddrMax |
.1.3.6.1.4.1.351.130.2.1.1.10 |
|
This object specifies the maximum VCI that
PAR can use for configuring connection in
the interface.
|
| parTrkId |
.1.3.6.1.4.1.351.130.2.2.1.1 |
|
This object specifies the logical trunk number
associated with the trunk at the local node.
|
| parTrkStatReserve |
.1.3.6.1.4.1.351.130.2.2.1.2 |
|
Specifies the bandwidth reserved as Statistical
Reserve on the trunk in units of cells per second.
This object cannot take a value beyond the bandwidth
capacity of the trunk.
|
| parTrkCnfgCcRestrict |
.1.3.6.1.4.1.351.130.2.2.1.3 |
|
This object specifies the operators preference for
routing control plane traffic on the interface.
If the object is set to False, then the interface may
be chosen for control plane traffic. If it is True, then
the interface is not chosen, unless there is no other
trunk with parIfOperStatus added(2), in which case it is
chosen regardless of the value of this object.
|
| parTrkCnfgLineType |
.1.3.6.1.4.1.351.130.2.2.1.4 |
|
This object specifies the type of interface terrestrial
or satellite. The interfaces configured as terrestrial(1)
are preferred over those configured as satellite(2) for
routing control plane traffic.
This information is also used for connections for which
routing restrictions are specified.
|
| parTrkCnfgPassSync |
.1.3.6.1.4.1.351.130.2.2.1.5 |
|
This object specifies whether the trunk can be
used to pass clock sync.
If the value of this object is True, clock can be
synchronized through the trunk; otherwise not.
|
| parTrkCnfgDerouteDelay |
.1.3.6.1.4.1.351.130.2.2.1.6 |
|
This object specifies the value of deroute delay
timer in seconds.
|
| parTrkCnfgTrafficClassFst |
.1.3.6.1.4.1.351.130.2.2.1.7 |
|
This object indicates whether Foresight traffic
can be routed over the trunk. If the value is true(1),
it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassFr |
.1.3.6.1.4.1.351.130.2.2.1.8 |
|
This object indicates whether Frame Relay traffic
can be routed over the trunk. If the value is true(1),
it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassNts |
.1.3.6.1.4.1.351.130.2.2.1.9 |
|
This object indicates whether Non-Time Stamped
traffic can be routed over the trunk. If the value
is true(1) it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassTs |
.1.3.6.1.4.1.351.130.2.2.1.10 |
|
This object indicates whether Time Stamped
traffic can be routed over the trunk. If the value
is true(1) it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassVoice |
.1.3.6.1.4.1.351.130.2.2.1.11 |
|
This object indicates whether Voice traffic
can be routed over the trunk. If the value is
true(1), it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassCbr |
.1.3.6.1.4.1.351.130.2.2.1.12 |
|
This object indicates whether Constant Bit Rate
traffic can be routed over the trunk. If the value
is true(1), it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassVbr |
.1.3.6.1.4.1.351.130.2.2.1.13 |
|
This object indicates whether Variable Bit Rate
traffic can be routed over the trunk. If the value
is true(1), it can be rerouted otherwise not.
|
| parTrkCnfgTrafficClassAbr |
.1.3.6.1.4.1.351.130.2.2.1.14 |
|
This object indicates whether Available Bit Rate
traffic can be routed over the trunk. If the value
is true(1), it can be rerouted otherwise not.
|
| parTrkCnfgAdminStatus |
.1.3.6.1.4.1.351.130.2.2.1.15 |
|
This object can be used to add or delete the trunk.
The value of this object can be set to add(1) only
if the parIfOperStatus is up(1). The value can be
set to delete if parIfOperStatus is added or
added-failed
|
| parTrkCnfgRoutingCost |
.1.3.6.1.4.1.351.130.2.2.1.16 |
|
This object specifies the cost associated with
the trunk for the purpose of routing the connections.
This object has significance if cost based routing
feature is enabled(parCmParmsCostBased)
|
| parTrkCnfgVccConids |
.1.3.6.1.4.1.351.130.2.2.1.17 |
|
The maximum number of routing resource available
on the trunk for VCC connections.
|
| parTrkCnfgVpcConids |
.1.3.6.1.4.1.351.130.2.2.1.18 |
|
The maximum number of routing resource available
on the trunk for VPC connections
|
| parTrkLocalSlotNumber |
.1.3.6.1.4.1.351.130.2.2.1.19 |
|
This object specifies the slot number of the
interface card associated with the trunk at the
local node.
|
| parTrkLocalPortNumber |
.1.3.6.1.4.1.351.130.2.2.1.20 |
|
This object specifies the port number of the interface card
associated with the trunk at the local node.
|
| parTrkLocalVTrunkId |
.1.3.6.1.4.1.351.130.2.2.1.21 |
|
This object specifies the Virtual trunk of the
interface card associated with the trunk at the
local node. The value of this object is between
1 and 254, inclusive for a virtual trunk and
255 for a physical trunk.
|
| parTrkRemoteNodeId |
.1.3.6.1.4.1.351.130.2.2.1.22 |
|
This object specifies the node number of the
node attached to the remote end of the trunk.
|
| parTrkRemoteTrunkId |
.1.3.6.1.4.1.351.130.2.2.1.23 |
|
This object specifies the logical trunk number
at the node on the remote end of the trunk.
|
| parTrkRemoteSlotNumber |
.1.3.6.1.4.1.351.130.2.2.1.24 |
|
This object specifies the slot number of the
interface card to which the trunk is attached
on the remote node.
|
| parTrkRemotePortNumber |
.1.3.6.1.4.1.351.130.2.2.1.25 |
|
This object specifies the port number of the
interface card to which the trunk is attached
on the remote node.
|
| parTrkRemoteVTrunkId |
.1.3.6.1.4.1.351.130.2.2.1.26 |
|
This object specifies the Virtual trunk of the
interface card associated with the trunk at the
remote node. The value of this object is between
1 and 254, inclusive for a virtual trunk and 255
for a physical trunk.
|
| parTrkRemoteNodeIP |
.1.3.6.1.4.1.351.130.2.2.1.27 |
|
This object specifies the IP address for the
Remote node, used for communication with NMS
|
| parTrkRemoteNodeType |
.1.3.6.1.4.1.351.130.2.2.1.28 |
|
Specifies the type of the node.
|
| parTrkRemoteNodeName |
.1.3.6.1.4.1.351.130.2.2.1.29 |
|
This object specifies the name of the remote
node and is unique among all the nodes in the network.
|
| parTrkAlarmStatus |
.1.3.6.1.4.1.351.130.2.2.1.30 |
|
This object specifies the severity of the alarm
on the trunk.
clear(1) : No Alarm
minor(2) : Minor Alarm
major(3) : Major Alarm.
|
| parTrkAlarmType |
.1.3.6.1.4.1.351.130.2.2.1.31 |
|
This object specifies the type of alarm on
the trunk. The value of this object has no
significance if parTrunkAlarmStatus indicates no alarm.
rsrcunavail(1) : resources unavailable indicates that
the platform has not provided the resources
required to make this interface into a trunk.
commfail(2) : communication failure indicates that message
exchanged between neighboring nodes on this
trunk has failed.
unknown (3) : indicates that the alarm type is unknown to PAR,
for example if the platform has declared the
interface in alarm due to some physical problem
with the interface.
|
| parTrkBwCapacity |
.1.3.6.1.4.1.351.130.2.2.1.32 |
|
Specifies the bandwidth capacity of the trunk.
|
| parTrkLineLoad |
.1.3.6.1.4.1.351.130.2.2.1.33 |
|
Specifies the bandwidth used by the connections
routed over the trunk.
|
| parTrkLoadXmtUsedCbr |
.1.3.6.1.4.1.351.130.2.3.1.1 |
|
This object specifies the used bandwidth in the
transmit direction for CBR traffic.
|
| parTrkLoadRcvUsedCbr |
.1.3.6.1.4.1.351.130.2.3.1.2 |
|
This object specifies the used bandwidth in the
receive direction for CBR traffic
|
| parTrkLoadXmtUsedVbr |
.1.3.6.1.4.1.351.130.2.3.1.3 |
|
This object specifies the used bandwidth in the
transmit direction for VBR traffic.
|
| parTrkLoadRcvUsedVbr |
.1.3.6.1.4.1.351.130.2.3.1.4 |
|
This object specifies the used bandwidth in the
receive direction for VBR traffic.
|
| parTrkLoadXmtUsedAbr |
.1.3.6.1.4.1.351.130.2.3.1.5 |
|
This object specifies the used bandwidth in the
transmit direction for ABR.
|
| parTrkLoadRcvUsedAbr |
.1.3.6.1.4.1.351.130.2.3.1.6 |
|
This object specifies the used bandwidth in the
receive direction for ABR.
|
| parTrkLoadXmtUsedNts |
.1.3.6.1.4.1.351.130.2.3.1.7 |
|
This object specifies the used bandwidth in the
transmit direction for Non-Time Stamped.
|
| parTrkLoadRcvUsedNts |
.1.3.6.1.4.1.351.130.2.3.1.8 |
|
This object specifies the used bandwidth in the
receive direction for Non-Time Stamped.
|
| parTrkLoadXmtUsedTs |
.1.3.6.1.4.1.351.130.2.3.1.9 |
|
This object specifies the used bandwidth in the
transmit direction for Time-Stamped.
|
| parTrkLoadRcvUsedTs |
.1.3.6.1.4.1.351.130.2.3.1.10 |
|
This object specifies the used bandwidth in the
receive direction for Time-Stamped.
|
| parTrkLoadXmtUsedVoice |
.1.3.6.1.4.1.351.130.2.3.1.11 |
|
This object specifies the used bandwidth in the
transmit direction for Voice.
|
| parTrkLoadRcvUsedVoice |
.1.3.6.1.4.1.351.130.2.3.1.12 |
|
This object specifies the used bandwidth in the
receive direction for Voice.
|
| parTrkLoadXmtUsedBdataA |
.1.3.6.1.4.1.351.130.2.3.1.13 |
|
This object specifies the used bandwidth in the
transmit direction for Busty Data A.
|
| parTrkLoadRcvUsedBdataA |
.1.3.6.1.4.1.351.130.2.3.1.14 |
|
This object specifies the used bandwidth in the
receive direction for Bursty Data A.
|
| parTrkLoadXmtUsedBdataB |
.1.3.6.1.4.1.351.130.2.3.1.15 |
|
This object specifies the used bandwidth in the
transmit direction for Bursty Data B.
|
| parTrkLoadRcvUsedBdataB |
.1.3.6.1.4.1.351.130.2.3.1.16 |
|
This object specifies the used bandwidth in the
receive direction for Bursty Data B.
|
| parTrkLoadVccConidsUsed |
.1.3.6.1.4.1.351.130.2.3.1.17 |
|
This object specifies the number of conids used
for VCCs (not used) on the trunk.
|
| parTrkLoadVpcConidsUsed |
.1.3.6.1.4.1.351.130.2.3.1.19 |
|
This object specifies the number of conids
Used for VPCs (not used) on the trunk.
|
| parConnLocalSlot |
.1.3.6.1.4.1.351.130.3.1.1.1 |
|
This object specifies the slot number part of the
local endpoint connection address.
|
| parConnLocalPort |
.1.3.6.1.4.1.351.130.3.1.1.2 |
|
This object specifies the port number part of the
local endpoint connection address.
|
| parConnLocalVpi |
.1.3.6.1.4.1.351.130.3.1.1.3 |
|
This object specifies the Virtual Path Identifier
part of the local endpoint connection address.
|
| parConnLocalVci |
.1.3.6.1.4.1.351.130.3.1.1.4 |
|
This object specifies the Virtual Channel Identifier
part of the local endpoint connection address.
|
| parConnMasterShip |
.1.3.6.1.4.1.351.130.3.1.1.5 |
|
This object specifies whether this end of the
connection is the master or the slave of the
connection. The value true(1) signifies the
master end and false(2) signifies slave end.
|
| parConnLocalVcIndx |
.1.3.6.1.4.1.351.130.3.1.1.6 |
|
This object specifies the Virtual Connection Index
at this node. It is used by Network Management to
correlate this end of the connection with the remote end.
|
| parConnLocalEndpt |
.1.3.6.1.4.1.351.130.3.1.1.7 |
|
This object specifies the actual physical connection
endpoint at the local node.
|
| parConnRemoteNodeName |
.1.3.6.1.4.1.351.130.3.1.1.8 |
|
This object specifies the node name of the
remote endpoint. For a intra-switch connection
or feeder connection this object would specify
the self node name.
|
| parConnRemoteSlot |
.1.3.6.1.4.1.351.130.3.1.1.9 |
|
This object specifies the slot number part of
the remote endpoint connection address.
|
| parConnRemotePort |
.1.3.6.1.4.1.351.130.3.1.1.10 |
|
This object specifies the port number part of
the remote endpoint connection address.
|
| parConnRemoteVpi |
.1.3.6.1.4.1.351.130.3.1.1.11 |
|
This object specifies the VPI part of the
remote endpoint connection address.
|
| parConnRemoteVci |
.1.3.6.1.4.1.351.130.3.1.1.12 |
|
This object specifies the VCI part of the
remote endpoint connection address.
|
| parConnRemoteVcIndx |
.1.3.6.1.4.1.351.130.3.1.1.13 |
|
This object specifies the Virtual Connection Index
at the remote node. It is used by Network Management
to correlate this end of the connection with the
remote end..
|
| parConnOperStatus |
.1.3.6.1.4.1.351.130.3.1.1.14 |
|
This object specifies the status of connection
as known and determined by PAR. The status shall be
OK if there is an A-bit alarm on the connection.
|
| parConnAdminStatus |
.1.3.6.1.4.1.351.130.3.1.1.15 |
|
This object is used by the operator to reroute
or down/up a connection. The value of this object
is up(1) when the connection is created.
If the value of the object is set to down(1)
the connection is derouted (if it is routed) and
parConnOperStatus object is set to not routed.
If the value of the object is up (2) and it is set
to reroute(3) the connection is derouted and attempt
is made to reroute the connection. If the value of the
object is down (1) and the it is set to reroute (3),
no action is performed and the object's value does not
changes.
If the value of object is down(1) and is set to up(2),
an attempt is made to reroute the connection.
|
| parConnRoute |
.1.3.6.1.4.1.351.130.3.1.1.16 |
|
This object specifies the current path on which
the connection is routed. A value of this object is
valid only if parConnOperStatus is routed.
The Null string specifies that the connection is not
routed.
Format: Nodename {Trk--Trk Nodename}
Where: Nodename = up to 8 characters,
Trk = slot.port.vtrk,
slot = 1 or 2 characters,
port = 1 or two characters, and
vtrk = 1 or two characters and is optional.
The portion of the format shown in braces {like this}
can be repeated up to 10 times.
|
| parConnRemoteEndpt |
.1.3.6.1.4.1.351.130.3.1.1.17 |
|
This object specifies the actual physical connection
endpoint at the remote end of the connection. It shall
be known only if the connection is a local(DAX) connection.
|
| parPrefRoute |
.1.3.6.1.4.1.351.130.3.1.1.18 |
|
This object specifies the preferred path for
the connection. The Null string specifies that
the connection does not have a preferred route.
Format: Nodename {Trk--Trk Nodename}
Where: Nodename = up to 8 characters,
Trk = slot.port.vtrk,
slot = 1 or 2 characters,
port = 1 or two characters, and
vtrk = 1 or two characters and is optional.
The portion of the format shown in braces {like this}
can be repeated up to 10 times.
|
| parConnFailRsn |
.1.3.6.1.4.1.351.130.3.1.1.19 |
|
This object specifies a reason code for the
failure of the connection.
|
| parRrtFailRsn |
.1.3.6.1.4.1.351.130.3.1.1.20 |
|
This object specifies the Reason of failure of
a connection to route.
|
| parConnRstrTyp |
.1.3.6.1.4.1.351.130.3.1.1.21 |
|
This object specifies the Route restriction
of a connection.
|
| parConnRstrZcs |
.1.3.6.1.4.1.351.130.3.1.1.22 |
|
This object specifies whether ZCS lines should
be avoided or not.
|
| parConnCos |
.1.3.6.1.4.1.351.130.3.1.1.23 |
|
This object specifies the COS for the connection.
|
| parClockIndex |
.1.3.6.1.4.1.351.130.4.1.1.1 |
|
This clock index is assigned by PAR.
|
| parClockType |
.1.3.6.1.4.1.351.130.4.1.1.2 |
|
Specifies the type of clock.
|
| parClockSource |
.1.3.6.1.4.1.351.130.4.1.1.3 |
|
Specifies source of the clock.
|
| parClockCurSource |
.1.3.6.1.4.1.351.130.4.1.1.4 |
|
Specifies whether clock source is a current clock source or not. The
value is true if the cloock source is current and false otherwise
|
| parClockSourceId |
.1.3.6.1.4.1.351.130.4.1.1.5 |
|
Specifies identification of the clock - for example
- if clock source is `Interface' then this field will
carry logical interface number
|
| parClockPath |
.1.3.6.1.4.1.351.130.4.1.1.6 |
|
Describes the path used for clock synchronization
|
