| wfDs1E1ModuleSlot |
.1.3.6.1.4.1.18.3.4.9.1.1.2 |
|
Instance ID slot, filled in by driver
|
| wfDs1E1ModuleModule |
.1.3.6.1.4.1.18.3.4.9.1.1.3 |
|
Instance ID slot, filled in by driver
|
| wfDs1E1ModuleDelete |
.1.3.6.1.4.1.18.3.4.9.1.1.1 |
|
Create/Delete parameter
|
| wfDs1E1ModulePrimaryClock |
.1.3.6.1.4.1.18.3.4.9.1.1.4 |
|
Specifies the primary source for transmit timing. Both ports use the same
transmit timing source. The options for timing source are internal timing
source, loop timing from either port and an external timing source.
|
| wfDs1E1ModuleSecondaryClock |
.1.3.6.1.4.1.18.3.4.9.1.1.5 |
|
Specifies the secondary source for transmit timing. During normal operation
transmit timing is derived from the primary timing source. If the primary
timing source fails, the software switches to secondary timing source.
|
| wfDs1E1ModuleCurrentClock |
.1.3.6.1.4.1.18.3.4.9.1.1.6 |
|
Indicates the clock source currently in use
|
| wfDs1E1ModuleExtClockOperational |
.1.3.6.1.4.1.18.3.4.9.1.1.7 |
|
Indicates whether the External clock is operational
|
| wfDs1E1ModuleLoop1ClockOperational |
.1.3.6.1.4.1.18.3.4.9.1.1.8 |
|
Indicates whether the timing source from port 1 is operational
|
| wfDs1E1ModuleLoop2ClockOperational |
.1.3.6.1.4.1.18.3.4.9.1.1.9 |
|
Indicates whether the timing source from port 2 is operational
|
| wfDs1E1ModuleLoop3ClockOperational |
.1.3.6.1.4.1.18.3.4.9.1.1.10 |
|
Indicates whether the timing source from port 3 is operational
|
| wfDs1E1ModuleLoop4ClockOperational |
.1.3.6.1.4.1.18.3.4.9.1.1.11 |
|
Indicates whether the timing source from port 4 is operational
|
| wfDs1E1ModuleCfgTxBufferUseCredits |
.1.3.6.1.4.1.18.3.4.9.1.1.12 |
|
Configured Transmit Buffer Credits. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. All values are
accepted. Care should be taken not to set this to a value which is
much greater than the default. The default can be read out of the
wfDs1E1ModuleTxBufferUseCredits attribute when the router is
running with this attribute set to zero. Sets to this attribute
may take up to one minute to take effect.
|
| wfDs1E1ModuleCfgRxBufferUseCredits |
.1.3.6.1.4.1.18.3.4.9.1.1.13 |
|
Configured Receive Buffer Credits. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero cuases router based default values to be used. Values larger
than the compiled ring size are truncated to the compiled ring
size. Sets to this attribute may take up to one minute to take
effect.
|
| wfDs1E1ModuleTxBufferUseCredits |
.1.3.6.1.4.1.18.3.4.9.1.1.14 |
|
Current Transmit Buffers available for use by module
|
| wfDs1E1ModuleRxBufferUseCredits |
.1.3.6.1.4.1.18.3.4.9.1.1.15 |
|
Current Receive Buffers available for use by module
|
| wfDs1E1PortMapSlot |
.1.3.6.1.4.1.18.3.4.9.2.1.2 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1PortMapConnector |
.1.3.6.1.4.1.18.3.4.9.2.1.3 |
|
Instance ID Connector, filled in by driver
|
| wfDs1E1PortMapDelete |
.1.3.6.1.4.1.18.3.4.9.2.1.1 |
|
Create/Delete parameter
|
| wfDs1E1PortMapLineNumber |
.1.3.6.1.4.1.18.3.4.9.2.1.4 |
|
LineNumber off of which all other MIB instances are indexed.
|
| wfDs1E1PortMapDslId |
.1.3.6.1.4.1.18.3.4.9.2.1.5 |
|
When this T1/E1 interface is configured for Primary Rate ISDN (PRI) this
attribute provides the ID of this Digital Subscriber Loop (DSL) interface.
Each T1 or E1 PRI interface on a particular slot is assigned a unique DSL
ID.
|
| wfDs1E1PortLineNumber |
.1.3.6.1.4.1.18.3.4.9.3.1.4 |
|
LineNumber for this port. This value is assigned at configuration time
and uniquely identifies this interface. This LineNumber not equal to
any of the LineNumbers assigned to the LogicalLines configured through
this Port.
|
| wfDs1E1PortDelete |
.1.3.6.1.4.1.18.3.4.9.3.1.1 |
|
Create/Delete parameter
|
| wfDs1E1PortDisable |
.1.3.6.1.4.1.18.3.4.9.3.1.2 |
|
Enable/Disable parameter
|
| wfDs1E1PortState |
.1.3.6.1.4.1.18.3.4.9.3.1.3 |
|
Line Driver state variable
|
| wfDs1E1PortMtu |
.1.3.6.1.4.1.18.3.4.9.3.1.5 |
|
MTU parameter. Obsoleted, it is no longer referenced.
|
| wfDs1E1PortSignalLevel |
.1.3.6.1.4.1.18.3.4.9.3.1.6 |
|
Specifies T1 transmit power level, in terms of DB. They
translate into cable length as follows:
0.0dB -> 0-133 ft
0.5dB -> 133-266 ft
0.8dB -> 266-399 ft
1.1dB -> 399-533 ft
1.5dB -> 533-655 ft
|
| wfDs1E1PortSetupAlarmThreshold |
.1.3.6.1.4.1.18.3.4.9.3.1.7 |
|
Specifies setup time for performance failure conditions,
in seconds. When a performance defect is present for greater
than the time specified by this parameter a performance
failure is registered and a message is logged.
|
| wfDs1E1PortClearAlarmThreshold |
.1.3.6.1.4.1.18.3.4.9.3.1.8 |
|
Specifies clear time for performance failure conditions,
in seconds. When a performance failure condition has been
cleared for greater than the time specified by this parameter
then the failure cleared condition is registered and a
message is logged.
|
| wfDs1E1PortFdlTargetHdlcAddress |
.1.3.6.1.4.1.18.3.4.9.3.1.9 |
|
Selects between the two FDL target address modes. This determines
whether the near-end FDL will respond to HDLC address AZ or
BY in the FDL messages received from the far-end.
|
| wfDs1E1PortAcceptLoopbackRequest |
.1.3.6.1.4.1.18.3.4.9.3.1.10 |
|
The DS1E1 link module is capable of detecting loop up and loop down
codes received from the far end. This parameter enables and disables
loop up/down code detection circuitry. If enabled, this interface
will accept and comply with a request to go into loopback mode from
a far end device.
|
| wfDs1E1PortLoopbackState |
.1.3.6.1.4.1.18.3.4.9.3.1.11 |
|
Indicates the current loopback state of this interface. The interface
can be in one the following states:
Payload Loopback
Line Loopback
no loopback
Payload or Line loopback modes can be initiated by either of two methods:
Manager requested Loopback (MGRREQPAYLOADLOOP or MGRREQLINELOOP) is
initiated by the Manager of this device.
Network requested Loopback (NETREQPAYLOADLOOP or NETREQLINELOOP) is
initiated by this interface receiving an in-band request on the network
from the far end device.
|
| wfDs1E1PortBertMode |
.1.3.6.1.4.1.18.3.4.9.3.1.12 |
|
An option to generate and analyze specific test patterns
is provided in BERT mode of operation. Only one port
can be in BERT mode at a time. This attribute selects
normal or BERT mode of operation
|
| wfDs1E1PortBertTestPattern |
.1.3.6.1.4.1.18.3.4.9.3.1.13 |
|
When a port is in BERT mode, it is capable of generating
a set of known patterns. This paramater selects between those
patterns
|
| wfDs1E1PortBertSendAlarm |
.1.3.6.1.4.1.18.3.4.9.3.1.14 |
|
Specifies a Alarm Indication Signal (AIS) (Blue Alarm) or yellow alarm to
be transmitted while in BERT mode.
|
| wfDs1E1PortInternationalBit |
.1.3.6.1.4.1.18.3.4.9.3.1.15 |
|
Specifies if the International bit should be set in
the E1 frame
|
| wfDs1E1PortLineApplication |
.1.3.6.1.4.1.18.3.4.9.3.1.16 |
|
Specifies the application that the LogicalLines of this Port will provide.
NONPRI indicates that all of the LogicalLines will have a permanent Cct
number and will not be used to dial to varying destinations. PRI
indicates that some or all of the ds0s of this port will be used for switched
Ccts using ISDN. MIXED indicates that some of the ds0s are being used for
switched Ccts using ISDN and some are being used for non PRI permanent
connections for other applications such as leased lines or Frame Relay.
|
| wfDs1E1PortLoggingEnableMask |
.1.3.6.1.4.1.18.3.4.9.3.1.17 |
|
Specifies which catagories of extended event log messages are enabled for
logging. Current bit definitions are:
bit 31 bit 0
+--------------------------------+
| |
+--------------------------------+
bit0 ISDN PRI debug messages
bit1-31 reserved
|
| wfDs1E1PortSendPrmCrAddressBit |
.1.3.6.1.4.1.18.3.4.9.3.1.18 |
|
Specifies the Performance message as originating from either a
Carrier or Customer Installation (CI). As the performance
message is sent out the FDL, the PRM Opening Address C/R bit
is either set (Carrier) or cleared (CI). This feature is only
supported by the QMCT1.
|
| wfDs1E1PortAcceptPrmCrAddressBit |
.1.3.6.1.4.1.18.3.4.9.3.1.19 |
|
Accepts only Performance messages originating from either a
Carrier or Customer Installation (CI), as determined below.
The PRM Opening Address C/R bit is read upon receiving a
performance message. If the Performance message does not
originate from the expected source, it is discarded. This
feature is only supported by the QMCT1.
|
| wfDs1E1PortLineImpedanceOption |
.1.3.6.1.4.1.18.3.4.9.3.1.20 |
|
Supports user selectible Line Impedance option for ASN MCE1
Net Modules.
|
| wfDs1E1PortFdlLoopInterframeFill |
.1.3.6.1.4.1.18.3.4.9.3.1.21 |
|
Enables the Loop Retention Interframe Time Fill for
the FDL after sending Loop Up Code. Also enables the
detection of the Loop Retention Code when placed into
Line or Payload loopback by the remote end.
|
| wfDs1E1PortRelayCtrl |
.1.3.6.1.4.1.18.3.4.9.3.1.22 |
|
The Relay on the QMCT1 will always be placed into
loopback for the following conditions:
1. Power Up
2. Reboot
3. Hardware Reset Button
4. System CRASH
However, when altering QMCT1 Port or Module MIBs' attributes
with a restart characteristic, the state of the Relay will
be controlled by this MIB attribute. When set to loop (1),
the Relay will go into loopback as the Port/Module is
re-initialized. The Relay will come out of loopback as the
Port/Module re-initialization is complete. When set to
noLoop (2), the Relay will remain in its present state as
the Port/Module is re-initialized.
|
| wfDs1E1PortRelayStatus |
.1.3.6.1.4.1.18.3.4.9.3.1.23 |
|
This attribute indicates the current state of the Relay
on the QMCT1. When set to loop (1), the Relay is currently
looping data from the Rx path onto the Tx path. When set
to noLoop (2), the Rx path and Tx path are connected to the
Framer. Note that the Framer may be placed into loopback
without affecting this attribute.
|
| wfDs1E1PortPrimaryClockSource |
.1.3.6.1.4.1.18.3.4.9.3.1.24 |
|
Selects the Primary source of the Tx Clock for the DS1/E1
interface
|
| wfDs1E1PortSecondaryClockSource |
.1.3.6.1.4.1.18.3.4.9.3.1.25 |
|
Selects the Secondary source of the Tx Clock for the DS1/E1
interface
|
| wfDs1E1PortCurrentClock |
.1.3.6.1.4.1.18.3.4.9.3.1.26 |
|
Indicates the clock source currently in use by the DS1
|
| wfDs1E1PortExtClockOperational |
.1.3.6.1.4.1.18.3.4.9.3.1.27 |
|
Indicates whether the External clock is operational
|
| wfDs1E1ConfigPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.4.1.2 |
|
The index ID for this record. It is the line number assigned to a port
in the wfDs1E1PortMapEntry for a port.connector pair. Its channel field
should be 0.
|
| wfDs1E1ConfigDelete |
.1.3.6.1.4.1.18.3.4.9.4.1.1 |
|
Create/Delete attribute
|
| wfDs1E1ConfigIfIndex |
.1.3.6.1.4.1.18.3.4.9.4.1.3 |
|
Currently this is the sames as wfDs1E1LinePortIndex
|
| wfDs1E1ConfigTimeElapsed |
.1.3.6.1.4.1.18.3.4.9.4.1.4 |
|
The number of seconds that have elapsed since the beginning of the
current error-measurement period. Only relevant when the
wfDs1E1ConfigLineType is ESF and the wfDs1E1ConfigFdl is AT&T 54016.
|
| wfDs1E1ConfigValidIntervals |
.1.3.6.1.4.1.18.3.4.9.4.1.5 |
|
The number of previous intervals for which valid data was collected. The
value will be 96 unless the interface was brought on-line within the last
24 hours, in which case the value will be the number of complete 15 minute
intervals the since interface has been online. Only relevant when the
wfDs1E1ConfigLineType is ESF and the wfDs1E1ConfigFdl is AT&T 54016.
|
| wfDs1E1ConfigLineType |
.1.3.6.1.4.1.18.3.4.9.4.1.6 |
|
This attribute is used to configure the line framing type to match
the carrier's framing. SF and ESF are T1 framing types and the main
differences between the two are the number of frames in a superframe
and the use of the f-bit. The E1, E1CRC, E1MF, and E1CRCMF are used
for E1 lines.
|
| wfDs1E1ConfigLineCoding |
.1.3.6.1.4.1.18.3.4.9.4.1.7 |
|
This variable describes the variety of Zero Code Suppression used on the
link, which in turn affects a number of its characteristics. It should
be set to match the carrier.
AMI (alternate mark inversion) refers to a mode wherein no zero code
suppression is present and the line encoding does not solve the problem
directly. In this application, the higher layer must provide data
which meets or exceeds the pulse density requirements, such as inverting
HDLC data. This could be used for T1 or E1 lines.
B8ZS refers to the use of a specified pattern of normal bits and bipolar
violations which are used to replace a sequence of eight zero bits. This
can be used on T1 lines while HDB3 provides similar functionality for
E1 links.
|
| wfDs1E1ConfigSendCode |
.1.3.6.1.4.1.18.3.4.9.4.1.8 |
|
This variable is currently read-only and it indicates what type of code is
being sent across the DS1 interface by the device. The values mean:
SENDNOCODE - sending looped or normal data
SENDLINECODE - sending a request for a line loopback
SENDPAYLOADCODE - sending a request for a payload loopback
SENDRESETCODE - sending a loopback termination request
SENDQRS - sending a Quasi-Random Signal (QRS) test pattern
SEND511PATTERN - sending a 511 bit fixed test pattern
SEND3IN24PATTERN - sending a fixed test pattern of 3 bits set in 24
SENDOTHERTESTPATTERN - sending a test pattern other than those
described by this object
|
| wfDs1E1ConfigCircuitIdentifier |
.1.3.6.1.4.1.18.3.4.9.4.1.9 |
|
This attribute is not used and appears here as a place holder only. If it
was implemented then it would contain the transmission vendor's circuit
identifier, for the purpose of facilitating troubleshooting.
|
| wfDs1E1ConfigLoopbackConfig |
.1.3.6.1.4.1.18.3.4.9.4.1.10 |
|
This variable represents the loopback configuration of the DS1 interface.
The value NOLOOP indicates the port is not in loopback. The value
PAYLOADLOOP indicates the port is in payload loopback which means that
data is looped back after it goes through the framer. The value LINELOOP
indicates the port is in line loopback which means that data is looped
back before the framer.
|
| wfDs1E1ConfigLineStatus |
.1.3.6.1.4.1.18.3.4.9.4.1.11 |
|
This variable is a bit-map which indicates the Line Status of the
interface. It contains loopback, failure, received 'alarm' and
transmitted 'alarm' information.
The bit definition as as follows with bit #0 being the LSB.
bit 0 NOALARM - No alarm present, set only when none of the other bits are.
1 RCVFARENDLOF - Far end LOF (a.k.a., Yellow Alarm)
2 XMTFARENDLOF - Near end sending LOF Indication
3 RCVAIS - Far end sending AIS
4 XMTAIS - Near end sending AIS
5 LOSSOFFRAME - Near end LOF (a.k.a., Red Alarm)
6 LOSSOFSIGNAL - Near end Loss Of Signal
7 LOOPBACKSTATE - Near end is looped
8 T16AIS - E1 only, TS16 AIS
9 RCVFARENDLOMF - E1 only, Far End Sending TS16 LOMF
10 XMTFARENDLOMF - E1 only, Near End Sending TS16 LOMF
11 RCVTESTCODE - Near End detects a test code
12 OTHERFAILURE - any line status not defined here'
|
| wfDs1E1ConfigSignalMode |
.1.3.6.1.4.1.18.3.4.9.4.1.12 |
|
This attribute is not implemented and exists here only as a place holder.
|
| wfDs1E1ConfigTransmitClockSource |
.1.3.6.1.4.1.18.3.4.9.4.1.13 |
|
The source of Tranmit Clock. LOOPTIMING indicates that the recovered
receive clock is used as the transmit clock. LOCALTIMING indicates that
a local clock source is used. Either the internal clock or the external
clock through the extra connector on the board. THROUGHTIMING indicates
that recovered receive clock from another interface is used as the
transmit clock.
|
| wfDs1E1ConfigFdl |
.1.3.6.1.4.1.18.3.4.9.4.1.14 |
|
This attribute is used to configure the type facilities data link (FDL).
The ANSI403 configures the port to use the FDL exchange described in
the ANSI T1 403 specification. ATT54016 is used to configure the port
for the for the FDL exchange listed in the AT&T 54016 document. NONE
is used when no FDL is desired. The FDL can only be used when the line
type is ESF.
|
| wfDs1E1ActionPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.5.1.1 |
|
Instance ID LineNumber, filled in by driver
|
| wfDs1E1ActionBertReset |
.1.3.6.1.4.1.18.3.4.9.5.1.2 |
|
Reset counters on BERT device
|
| wfDs1E1ActionBertErrorInsert |
.1.3.6.1.4.1.18.3.4.9.5.1.3 |
|
Indicates that an error be injected into the transmitted data
stream while in BERT mode.
|
| wfDs1E1ActionSendLoopCode |
.1.3.6.1.4.1.18.3.4.9.5.1.4 |
|
Selects a Loop Up/Down code to be sent to the remote end
|
| wfDs1E1ActionSendFdlLoopbackCode |
.1.3.6.1.4.1.18.3.4.9.5.1.5 |
|
Selects an FDL code to be sent to the remote end.
|
| wfDs1E1ActionSendLoopUpFractionalCode |
.1.3.6.1.4.1.18.3.4.9.5.1.6 |
|
Selects Fractional Loop Up code to be sent to the remote end.
Value passed through this attribute is the Logical Line number
(1 through 24). This feature is only supported by the QMCT1.
|
| wfDs1E1ActionSendLoopDownFractionalCode |
.1.3.6.1.4.1.18.3.4.9.5.1.7 |
|
Selects Fractional Loop Down code to be sent to the remote
end. Value passed through this attribute is the Logical Line
number (1 through 24). This feature is only supported by the
QMCT1.
|
| wfDs1E1ActionClearFractionalLoopState |
.1.3.6.1.4.1.18.3.4.9.5.1.8 |
|
Removes any Logical Line left in hardware Fractional T1
loopback state. The Logical Line number is passed as an
argument. This feature is only supported by the QMCT1.
|
| wfDs1E1ActionClearFdlStats |
.1.3.6.1.4.1.18.3.4.9.5.1.9 |
|
Clears this port's FDL Statistics. This feature is only
supported by the QMCT1.
|
| wfDs1E1ActionClearCurrentStats |
.1.3.6.1.4.1.18.3.4.9.5.1.10 |
|
Clears this port's Current 15 minute Statistics.
|
| wfDs1E1ActionClearFarEndCurrentStats |
.1.3.6.1.4.1.18.3.4.9.5.1.11 |
|
Clears this port's Far End, Current 15 minute Statistics.
|
| wfDs1E1ActionClearDayCurrentStats |
.1.3.6.1.4.1.18.3.4.9.5.1.12 |
|
Clears this port's Current Day Statistics.
|
| wfDs1E1ActionClearFarEndDayCurrentStats |
.1.3.6.1.4.1.18.3.4.9.5.1.13 |
|
Clears this port's Far End, Current Day Statistics.
|
| wfDs1E1ActionClearIntervalStats |
.1.3.6.1.4.1.18.3.4.9.5.1.14 |
|
Clears All Interval Statistics (15 minute and day) of this port.
|
| wfDs1E1ActionClearFarEndIntervalStats |
.1.3.6.1.4.1.18.3.4.9.5.1.15 |
|
Clears All Far End Interval Statistics (15 minute and day) of this port.
|
| wfLogicalLinePortLineNumber |
.1.3.6.1.4.1.18.3.4.9.6.1.4 |
|
Instance ID PortLineNumber, filled in by driver
|
| wfLogicalLineIndex |
.1.3.6.1.4.1.18.3.4.9.6.1.5 |
|
Index for this line instance, filled in by driver.
The index corresponds to the position of the
circuit, from 1 to 31, on the port.
|
| wfLogicalLineDelete |
.1.3.6.1.4.1.18.3.4.9.6.1.1 |
|
Create/Delete parameter
|
| wfLogicalLineDisable |
.1.3.6.1.4.1.18.3.4.9.6.1.2 |
|
Enable/Disable parameter
|
| wfLogicalLineState |
.1.3.6.1.4.1.18.3.4.9.6.1.3 |
|
Line Driver state variable
|
| wfLogicalLineCct |
.1.3.6.1.4.1.18.3.4.9.6.1.6 |
|
Circuit number for this line instance
|
| wfLogicalLineLineNumber |
.1.3.6.1.4.1.18.3.4.9.6.1.7 |
|
LineNumber for this logical line instance. This is the same line number
contained in the PORT_TABLE with the channel field nonzero.
|
| wfLogicalLineBofl |
.1.3.6.1.4.1.18.3.4.9.6.1.8 |
|
Selects Breath of Life (BOFL) parameter. If selected, a BOFL
packet is sent out on the wire as often as specifies by the
wfLogicalLineBoflTmo parameter
|
| wfLogicalLineBoflTmo |
.1.3.6.1.4.1.18.3.4.9.6.1.9 |
|
Indicates the time-period between BOFL packets
|
| wfLogicalLineFractionalLoopback |
.1.3.6.1.4.1.18.3.4.9.6.1.10 |
|
Any Logical Line on this T1/E1 port is capable of being put into
loopback, i.e. data coming into that circuit from the wire is
mirrorred back onto the wire. This parameter enables or
disables this loopback feature on any circuit.
|
| wfLogicalLineTimeSlotAssignment |
.1.3.6.1.4.1.18.3.4.9.6.1.11 |
|
Lists the time-slots which constitute this channel. Read only attribute
that contains a list of time-slots from 1 to 31 used by the channel
|
| wfLogicalLineMtu |
.1.3.6.1.4.1.18.3.4.9.6.1.12 |
|
Contains the largest frame size that can be received by the logical line.
Anything larger than the MTU will be discarded. In all cases except when
the wfLogicalLineWanProtocol is LAPB, this value will be the same as
wfLogicalLineCfgMtu. In the LAPB case it will be twice wfLogicalLineCfgMtu
with a maximum of 4608.
|
| wfLogicalLineMadr |
.1.3.6.1.4.1.18.3.4.9.6.1.13 |
|
Line MAC address, fixed - line driver fills in from the 48 bit
address stored in the serial number prom.
|
| wfLogicalLineWanProtocol |
.1.3.6.1.4.1.18.3.4.9.6.1.14 |
|
WAN protocol selection is provided via this parameter. The
supported protocols can be selected per circuit.
|
| wfLogicalLineHdlcService |
.1.3.6.1.4.1.18.3.4.9.6.1.15 |
|
HDLC Service type for this line. Transparent is raw HDLC mode, LLC1 will
prefix the HDLC address and control fields to the frame.
|
| wfLogicalLineLocalHdlcAddress |
.1.3.6.1.4.1.18.3.4.9.6.1.16 |
|
This attribute is only used if the Wan protocol is Wellfleet Standard
Proprietary Point to Point. This attribute is unused for other Wan
protocols.
The local HDLC address can take on values between 1 and 7. The default is
7. 1 is refered to as DCE. 3 is refered to DTE. All others are refered
to as EXPLICIT. EXPLICIT indicates that the user has explicitely selected
the address.
|
| wfLogicalLineRemoteHdlcAddress |
.1.3.6.1.4.1.18.3.4.9.6.1.17 |
|
This attribute is only used if the Wan protocol is Wellfleet Standard
Proprietary Point to Point. This attribute is unused for other Wan
protocols.
The remote HDLC address can take on values between 1 and 7. The default is
7. 1 is refered to as DCE. 3 is refered to DTE. All others are refered
to as EXPLICIT. EXPLICIT indicates that the user has explicitely selected
the address.
|
| wfLogicalLineRateAdaption |
.1.3.6.1.4.1.18.3.4.9.6.1.18 |
|
Determines the number of bits and their bit positions
within the time-slot. 64k selection uses all 8 bits in
the time-slot. The two 56k selections use 7 of the 8
bits in the time-slot. 56k_MSB does not use the most
significant bit and 56k_LSB does not use the least
significant bit in the time-slot. If
the logical line is configured for DS0-A operation, rate
adaptions of 9.6 Kbps and 19.2 Kbps may be configured.
|
| wfLogicalLineIFTF |
.1.3.6.1.4.1.18.3.4.9.6.1.19 |
|
Determines the Interframe time fill character to be
transmitted by the MUNICH. In case of IFTF_FLAGS, 0x7E
is sent and in case of IFTF_IDLES 0xff is sent as the
interframe timefill characters.
|
| wfLogicalLineCRCSize |
.1.3.6.1.4.1.18.3.4.9.6.1.20 |
|
Determines the CRC Size. When CRC32 is selected a 32 bit
CRC is appended to the frame being transmitted and a 32
bit CRC check is performed on the received frame. When
CRC16 is selected, a 16 bit CRC is appended to the
transmitted frame and a 16 bit CRC is performed. on the
received frame.
|
| wfLogicalLineRxOctets |
.1.3.6.1.4.1.18.3.4.9.6.1.21 |
|
Number of octets received without error
|
| wfLogicalLineRxFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.22 |
|
Number of frames received without error
|
| wfLogicalLineTxOctets |
.1.3.6.1.4.1.18.3.4.9.6.1.23 |
|
Number of octets transmitted without error
|
| wfLogicalLineTxFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.24 |
|
Number of frames transmitted without error
|
| wfLogicalLineRxErrors |
.1.3.6.1.4.1.18.3.4.9.6.1.25 |
|
Number of receive errors
|
| wfLogicalLineTxErrors |
.1.3.6.1.4.1.18.3.4.9.6.1.26 |
|
Number of transmission errors
|
| wfLogicalLineLackRxResources |
.1.3.6.1.4.1.18.3.4.9.6.1.27 |
|
Number of Rx frames dropped due to lack of buffer resources
|
| wfLogicalLineLackTxResources |
.1.3.6.1.4.1.18.3.4.9.6.1.28 |
|
Number of Tx frames dropped due to lack of system resources
|
| wfLogicalLineTxUnderflows |
.1.3.6.1.4.1.18.3.4.9.6.1.29 |
|
Number of Tx frames dropped due to Transmit underflow
|
| wfLogicalLineRxOverflows |
.1.3.6.1.4.1.18.3.4.9.6.1.30 |
|
Number of Rx frames dropped due to Receive overflow
|
| wfLogicalLineRxNullFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.31 |
|
Number of short frames received (with no data bytes)
|
| wfLogicalLineRxShortFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.32 |
|
Number of short frames received whose length is either 1 or 2 data bytes.
|
| wfLogicalLineRxLossSyncs |
.1.3.6.1.4.1.18.3.4.9.6.1.33 |
|
Loss of synchronization on receiver
|
| wfLogicalLineRxCRCErrors |
.1.3.6.1.4.1.18.3.4.9.6.1.34 |
|
CRC error received
|
| wfLogicalLineRxNonOctetBits |
.1.3.6.1.4.1.18.3.4.9.6.1.35 |
|
Non-Octet bits received in frame
|
| wfLogicalLineRxLongFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.36 |
|
Frame longer than MFL received
|
| wfLogicalLineRxAbortFrames |
.1.3.6.1.4.1.18.3.4.9.6.1.37 |
|
Aborted frame received
|
| wfLogicalLineRxDescOverflows |
.1.3.6.1.4.1.18.3.4.9.6.1.38 |
|
Receive overflow on chip buffer
|
| wfLogicalLineRxReplenMisses |
.1.3.6.1.4.1.18.3.4.9.6.1.39 |
|
Count of number of packet buffer misses while attempting to
replenish driver receive ring
|
| wfLogicalLineRxIFCs |
.1.3.6.1.4.1.18.3.4.9.6.1.40 |
|
Number of times the device detects a change of interframe time-fill
between incomming frames.
|
| wfLogicalLineRxDropPackets |
.1.3.6.1.4.1.18.3.4.9.6.1.41 |
|
Number of packets dropped after reception
|
| wfLogicalLineCfgTxQueueLength |
.1.3.6.1.4.1.18.3.4.9.6.1.42 |
|
Configured Transmit Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. All values are
accepted. Care should be taken not to set this to a value which is
much greater than the default. The default can be read out of the
wfLoigcalLineTxQueueLength attribute when the router is running with
this attribute set to zero. Sets to this attribute may take up to
one minute to take effect.
|
| wfLogicalLineCfgRxQueueLength |
.1.3.6.1.4.1.18.3.4.9.6.1.43 |
|
Configured Receive Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero cuases router based default values to be used. Values larger
than the compiled ring size are truncated to the compiled ring
size. Sets to this attribute may take up to one minute to take effect.
|
| wfLogicalLineTxQueueLength |
.1.3.6.1.4.1.18.3.4.9.6.1.44 |
|
Current hardware transmit queue length
|
| wfLogicalLineRxQueueLength |
.1.3.6.1.4.1.18.3.4.9.6.1.45 |
|
Current Receive queue length
|
| wfLogicalLineTxQueueEmpties |
.1.3.6.1.4.1.18.3.4.9.6.1.46 |
|
The number of times the transmit ring is found
empty when transmitting packets
|
| wfLogicalLineRxIntProcs |
.1.3.6.1.4.1.18.3.4.9.6.1.47 |
|
DEBUG paramete - Receive Interrupt processing count
|
| wfLogicalLineTxIntProcs |
.1.3.6.1.4.1.18.3.4.9.6.1.48 |
|
DEBUG parameter - Tx interrupt processing count
|
| wfLogicalLineRxPktCorruptions |
.1.3.6.1.4.1.18.3.4.9.6.1.49 |
|
DEBUG parameter - Corruption check on receive
|
| wfLogicalLineTurboBofl |
.1.3.6.1.4.1.18.3.4.9.6.1.50 |
|
DEBUG parameter - Turbo bofl enabled or disabled
|
| wfLogicalLineBoflNum |
.1.3.6.1.4.1.18.3.4.9.6.1.51 |
|
DEBUG parameter - Number of breath of life packets per breath
of life
|
| wfLogicalLineBoflLen |
.1.3.6.1.4.1.18.3.4.9.6.1.52 |
|
DEBUG parameter - breath of life packet length
|
| wfLogicalLineOutQLen |
.1.3.6.1.4.1.18.3.4.9.6.1.53 |
|
The instantaneous current length of the output packet queue (in packets).
|
| wfLogicalLineLastChange |
.1.3.6.1.4.1.18.3.4.9.6.1.54 |
|
The value of SysUpTime at the time the interface entered it's current
operational state (UP state). SysUpTime is defined as the time (in
hundredths of a second) since the network management portion of the
system was last re-initialized. Usually the time since boot.
|
| wfLogicalLineCfgMtu |
.1.3.6.1.4.1.18.3.4.9.6.1.55 |
|
Specifies the largest frame size that can be received by the logical line.
Anything larger than the MTU will be discarded.
|
| wfLogicalLineRemoteLpbkDetection |
.1.3.6.1.4.1.18.3.4.9.6.1.56 |
|
This attribute enables Remote Loopback Detection. When enabled along with
wfLogicalLineBofl, the device driver will detect when it is receiving its
own BOFL packets and will bring the interface down assuming that somewhere
down stream the link has been put into loopback.
|
| wfLogicalLineLastState |
.1.3.6.1.4.1.18.3.4.9.6.1.57 |
|
The state which the Logical Line driver was in prior to the most recent
re-initialization.
|
| wfLogicalLineRxIdles |
.1.3.6.1.4.1.18.3.4.9.6.1.58 |
|
Number of received frames followed by ShortFrame errors reported by the
hardware. ShortFrame errors imediately after received frames actually
indicates an Idle (all 1s) interframe time fill. One ShortFrame is
allowed per received frame without incrementing wfLogicalLineRxErrors
or wfLogicalLineRxShortFrames. Additional ShortFrames will not increment
wfLogicalLineRxIdles but will increment both wfLogicalLineRxErrors and
wfLogicalLineRxShortFrames.
|
| wfLogicalLineRole |
.1.3.6.1.4.1.18.3.4.9.6.1.59 |
|
Specifies the role of this Logical Line. This attribute directs the Logical
Line to be either a normal permanent synchronous connection, a Primary Rate
ISDN 'D' channel or a Primary Rate ISDN 'B' channel.
|
| wfLogicalLineActiveCct |
.1.3.6.1.4.1.18.3.4.9.6.1.60 |
|
Active CCT number for this LogicalLine. Used in ISDN PRI to indicate the
CCT of the current call in progress.
|
| wfLogicalLineActualRateAdaption |
.1.3.6.1.4.1.18.3.4.9.6.1.61 |
|
Indicates the current Rate Adaption in use. This may differ from the
configured Rate Adaption in ISDN PRI applications. This attribute indicates
the number of bits and their bit positions within the time-slot. 64k
selection uses all 8 bits in the time-slot. The two 56k selections use 7 of
the 8 bits in the time-slot. 56k_MSB does not use the most significant bit
and 56k_LSB does not use the least significant bit in the time-slot. If
the logical line is configured for DS0-A operation, rate adaptions of
9.6 Kbps and 19.2 Kbps may be configured.
|
| wfLogicalLineBertMode |
.1.3.6.1.4.1.18.3.4.9.6.1.62 |
|
Enables BERT testing on a logical line level. This feature is
only supported by the QMCT1.
|
| wfLogicalLineBertTestPattern |
.1.3.6.1.4.1.18.3.4.9.6.1.63 |
|
Test pattern for BERT. This feature is only supported by the
QMCT1.
|
| wfLogicalLineAcceptFracLoopCode |
.1.3.6.1.4.1.18.3.4.9.6.1.64 |
|
Allows logical line to accept Fractional T1 Loop Code. This
feature is only supported by the QMCT1.
|
| wfLogicalLineDS0AStatus |
.1.3.6.1.4.1.18.3.4.9.6.1.65 |
|
Indicates logical line set to T1 DS0-A Subrates. This
feature is only supported by the QMCT1.
|
| wfLogicalLineNRZIEnable |
.1.3.6.1.4.1.18.3.4.9.6.1.66 |
|
Allows logical line to accept T1 NRZI encoding on logical
Line. This feature is only supported by the QMRT1.
|
| wfLogicalLineNRZIType |
.1.3.6.1.4.1.18.3.4.9.6.1.67 |
|
Defines logical line to T1 NRZI encoding as either Mark or
Space on logical Line. This feature is only supported by the QMRT1.
|
| wfDs1E1FracPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.7.1.2 |
|
Line number with a zero channel number field. Identifies the port
|
| wfDs1E1FracNumber |
.1.3.6.1.4.1.18.3.4.9.7.1.3 |
|
The time slot to be assigned
|
| wfDs1E1FracDelete |
.1.3.6.1.4.1.18.3.4.9.7.1.1 |
|
Create/Delete parameter
|
| wfDs1E1FracLogicalLineIndex |
.1.3.6.1.4.1.18.3.4.9.7.1.4 |
|
This time slot is assigned to the Logical Line identified by this
attribute.
|
| wfDs1E1FracActualLogicalLineIndex |
.1.3.6.1.4.1.18.3.4.9.7.1.5 |
|
This time slot can be manipulated by ISDN PRI Multi-Rate service.
This is the logical line to which the time slot is currently
allocated.
|
| wfDs1E1CurrentPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.10.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1CurrentESs |
.1.3.6.1.4.1.18.3.4.9.10.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
current 15 minute interval.
|
| wfDs1E1CurrentSESs |
.1.3.6.1.4.1.18.3.4.9.10.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface
in the current 15 minute interval.'
|
| wfDs1E1CurrentSEFSs |
.1.3.6.1.4.1.18.3.4.9.10.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1
interface in the current 15 minute interval.
|
| wfDs1E1CurrentUASs |
.1.3.6.1.4.1.18.3.4.9.10.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
current 15 minute interval.
|
| wfDs1E1CurrentCSSs |
.1.3.6.1.4.1.18.3.4.9.10.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
current 15 minute interval.
|
| wfDs1E1CurrentPCVs |
.1.3.6.1.4.1.18.3.4.9.10.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
current 15 minute interval.
|
| wfDs1E1CurrentLESs |
.1.3.6.1.4.1.18.3.4.9.10.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
current 15 minute interval.'
|
| wfDs1E1CurrentBESs |
.1.3.6.1.4.1.18.3.4.9.10.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the current 15 minute interval.
|
| wfDs1E1CurrentDMs |
.1.3.6.1.4.1.18.3.4.9.10.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in
the current 15 minute interval.'
|
| wfDs1E1CurrentLCVs |
.1.3.6.1.4.1.18.3.4.9.10.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the current 15 minute interval.'
|
| wfDs1E1CurrentSASs |
.1.3.6.1.4.1.18.3.4.9.10.1.12 |
|
The number of seconds, within the current 15 minute interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1CurrentAISSs |
.1.3.6.1.4.1.18.3.4.9.10.1.13 |
|
The number of seconds, within the current 15 minute interval,
containing one or more AIS defect.
|
| wfDs1E1CurrentFCs |
.1.3.6.1.4.1.18.3.4.9.10.1.14 |
|
The number of Path Failure Count error events detected
in the current 15 minute interval.
|
| wfDs1E1CurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.9.10.1.15 |
|
The number of seconds that have elapsed since the beginning of the
current error-measurement period.
|
| wfDs1E1CurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.9.10.1.16 |
|
The number of previous intervals for which valid data was collected. The
value will be 96 unless the interface was brought on-line within the last
24 hours, in which case the value will be the number of complete 15 minute
intervals the since interface has been online.
|
| wfDs1E1CurrentValidFlag |
.1.3.6.1.4.1.18.3.4.9.10.1.17 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1IntervalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.11.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1IntervalNumber |
.1.3.6.1.4.1.18.3.4.9.11.1.2 |
|
A number between 1 and 96, where 1 is the most recently completed 15 minute
interval and 96 is the least recently completed 15 minutes interval (assuming
that all 96 intervals are valid).
|
| wfDs1E1IntervalESs |
.1.3.6.1.4.1.18.3.4.9.11.1.3 |
|
The number of Errored Seconds, encountered by a DS1 interface in the current
15 minute interval.
|
| wfDs1E1IntervalSESs |
.1.3.6.1.4.1.18.3.4.9.11.1.4 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in one
of the previous 15 minute intervals.
|
| wfDs1E1IntervalSEFSs |
.1.3.6.1.4.1.18.3.4.9.11.1.5 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in one of the previous 15 minute intervals.
|
| wfDs1E1IntervalUASs |
.1.3.6.1.4.1.18.3.4.9.11.1.6 |
|
The number of Unavailable Seconds encountered by a DS1 interface in one of the
previous 15 minute intervals.
|
| wfDs1E1IntervalCSSs |
.1.3.6.1.4.1.18.3.4.9.11.1.7 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in one
of the previous 15 minute intervals.
|
| wfDs1E1IntervalPCVs |
.1.3.6.1.4.1.18.3.4.9.11.1.8 |
|
The number of Path Coding Violations encountered by a DS1 interface in one of
the previous 15 minute intervals.
|
| wfDs1E1IntervalLESs |
.1.3.6.1.4.1.18.3.4.9.11.1.9 |
|
The number of Line Errored Seconds encountered by a DS1 interface in one of
the previous 15 minute intervals.
|
| wfDs1E1IntervalBESs |
.1.3.6.1.4.1.18.3.4.9.11.1.10 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in
one of the previous 15 minute intervals.
|
| wfDs1E1IntervalDMs |
.1.3.6.1.4.1.18.3.4.9.11.1.11 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of
the previous 15 minute intervals.
|
| wfDs1E1IntervalLCVs |
.1.3.6.1.4.1.18.3.4.9.11.1.12 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
one of the previous 15 minute intervals.
|
| wfDs1E1IntervalSASs |
.1.3.6.1.4.1.18.3.4.9.11.1.13 |
|
The number of seconds, in one of the previous 15 minute intervals,
containing one or more SEFs or AIS defects.
|
| wfDs1E1IntervalAISSs |
.1.3.6.1.4.1.18.3.4.9.11.1.14 |
|
The number of seconds, in one of the previous 15 minute intervals,
containing one or more AIS defect.
|
| wfDs1E1IntervalFCs |
.1.3.6.1.4.1.18.3.4.9.11.1.15 |
|
The number of Path Failure Count error events detected
one of the previous 15 minute intervals.
|
| wfDs1E1IntervalValidFlag |
.1.3.6.1.4.1.18.3.4.9.11.1.16 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1TotalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.12.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1TotalESs |
.1.3.6.1.4.1.18.3.4.9.12.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the current
15 minute interval.
|
| wfDs1E1TotalSESs |
.1.3.6.1.4.1.18.3.4.9.12.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalSEFSs |
.1.3.6.1.4.1.18.3.4.9.12.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in the previous 24-hour interval.
|
| wfDs1E1TotalUASs |
.1.3.6.1.4.1.18.3.4.9.12.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalCSSs |
.1.3.6.1.4.1.18.3.4.9.12.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalPCVs |
.1.3.6.1.4.1.18.3.4.9.12.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalLESs |
.1.3.6.1.4.1.18.3.4.9.12.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalBESs |
.1.3.6.1.4.1.18.3.4.9.12.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the previous 24-hour interval.
|
| wfDs1E1TotalDMs |
.1.3.6.1.4.1.18.3.4.9.12.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the
previous 24-hour interval.
|
| wfDs1E1TotalLCVs |
.1.3.6.1.4.1.18.3.4.9.12.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the previous 24-hour interval.
|
| wfDs1E1TotalSASs |
.1.3.6.1.4.1.18.3.4.9.12.1.12 |
|
The number of seconds, in the previous 24-hour interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1TotalAISSs |
.1.3.6.1.4.1.18.3.4.9.12.1.13 |
|
The number of seconds, in the previous 24-hour interval,
containing one or more AIS defect.
|
| wfDs1E1TotalFCs |
.1.3.6.1.4.1.18.3.4.9.12.1.14 |
|
The number of Path Failure Count error events detected
in the previous 24-hour interval.
|
| wfDs1E1TotalValidFlag |
.1.3.6.1.4.1.18.3.4.9.12.1.15 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1AnsiPortLineNumber |
.1.3.6.1.4.1.18.3.4.8.13.1.1 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1AnsiCRCCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.2 |
|
Counts CRC-6 error events
|
| wfDs1E1AnsiBPVCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.3 |
|
Counts bipolar violations
|
| wfDs1E1AnsiOOFCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.4 |
|
Counts out-of-frame error events
|
| wfDs1E1AnsiFECounts |
.1.3.6.1.4.1.18.3.4.8.13.1.5 |
|
Counts errors in the FPS framing pattern
|
| wfDs1E1AnsiESCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.6 |
|
Counts errorred seconds
|
| wfDs1E1AnsiSESCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.7 |
|
Counts severly errorred seconds
|
| wfDs1E1AnsiUASCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.8 |
|
counts unavailable seconds
|
| wfDs1E1AnsiPRMR0Counts |
.1.3.6.1.4.1.18.3.4.8.13.1.9 |
|
Counts PRMs that ewre received in the FDL in
the last four seconds
|
| wfDs1E1AnsiPRMR1Counts |
.1.3.6.1.4.1.18.3.4.8.13.1.10 |
|
Counts PRMs that ewre received in the FDL in
the last four seconds
|
| wfDs1E1AnsiPRMR2Counts |
.1.3.6.1.4.1.18.3.4.8.13.1.11 |
|
Counts PRMs that ewre received in the FDL in
the last four seconds
|
| wfDs1E1AnsiPRMR3Counts |
.1.3.6.1.4.1.18.3.4.8.13.1.12 |
|
Counts PRMs that ewre received in the FDL in
the last four seconds
|
| wfDs1E1AnsiPRMESCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.13 |
|
Counts errorred seconds as reported in the Performance
report messages
|
| wfDs1E1AnsiPRMSESCounts |
.1.3.6.1.4.1.18.3.4.8.13.1.14 |
|
Counts severely errorred seconds as reported in the
Performance report messages
|
| wfDs1E1AnsiPRMECounts |
.1.3.6.1.4.1.18.3.4.8.13.1.15 |
|
Counts Performance report messages that are received
in error
|
| wfDs1E1BertStatsPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.14.1.1 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1BertStatsBitErrors |
.1.3.6.1.4.1.18.3.4.9.14.1.2 |
|
Bit error counter
|
| wfDs1E1BertStatsBits |
.1.3.6.1.4.1.18.3.4.9.14.1.3 |
|
Bit counter
|
| wfDs1E1CurrentFramerStatsPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.15.1.1 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1CurrentFramerStatsMediaType |
.1.3.6.1.4.1.18.3.4.9.15.1.2 |
|
The media type is either T1 or E1
|
| wfDs1E1CurrentFramerStatsBpvCounts |
.1.3.6.1.4.1.18.3.4.9.15.1.3 |
|
bipolar violations counter
|
| wfDs1E1CurrentFramerStatsCrc4Counts |
.1.3.6.1.4.1.18.3.4.9.15.1.4 |
|
CRC4 error counter
|
| wfDs1E1CurrentFramerStatsFebeCounts |
.1.3.6.1.4.1.18.3.4.9.15.1.5 |
|
Far End Block Error counter
|
| wfDs1E1CurrentFramerStatsOofCounts |
.1.3.6.1.4.1.18.3.4.9.15.1.6 |
|
Out of frame error counts. Out of frame is declared when at least two
of four (or five) consecutive framing bits are in error.
|
| wfDs1E1CurrentFramerStatsFeCounts |
.1.3.6.1.4.1.18.3.4.9.15.1.7 |
|
Framing error counts. In ESF mode this is the number of errored
superframes while in SF mode it is the number of incorrect framing
bits.
|
| wfDs1E1CurrentFramerStatsLossFrameFailures |
.1.3.6.1.4.1.18.3.4.9.15.1.8 |
|
Loss of frame failures. These occur when an out of frame event or
carrier loss happens
|
| wfDs1E1CurrentFramerStatsLossSignalFailures |
.1.3.6.1.4.1.18.3.4.9.15.1.9 |
|
Loss of Signal failure happen when receive carrier is lost
|
| wfDs1E1CurrentFramerStatsAlarmIndicationFailures |
.1.3.6.1.4.1.18.3.4.9.15.1.10 |
|
Alarm Indication signal Failures occur when 2 consecutive frames have
less than 3 zeros (total) in the data stream.
|
| wfDs1E1CurrentFramerStatsRemoteAlarmFailures |
.1.3.6.1.4.1.18.3.4.9.15.1.11 |
|
Remote alarm failure happen when the yellow alarm is detected
|
| wfDs1E1TotalFramerStatsPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.16.1.1 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1TotalFramerStatsMediaType |
.1.3.6.1.4.1.18.3.4.9.16.1.2 |
|
bipolar violations counter
|
| wfDs1E1TotalFramerStatsValidIntervals |
.1.3.6.1.4.1.18.3.4.9.16.1.3 |
|
The number of valid 15 minutes intervals in the last 24-hour period
|
| wfDs1E1TotalFramerStatsBpvCounts |
.1.3.6.1.4.1.18.3.4.9.16.1.4 |
|
bipolar violations counter
|
| wfDs1E1TotalFramerStatsCrc4Counts |
.1.3.6.1.4.1.18.3.4.9.16.1.5 |
|
CRC4 error counter
|
| wfDs1E1TotalFramerStatsFebeCounts |
.1.3.6.1.4.1.18.3.4.9.16.1.6 |
|
Far End Block Error counter
|
| wfDs1E1TotalFramerStatsOofCounts |
.1.3.6.1.4.1.18.3.4.9.16.1.7 |
|
Out of frame error counts. Out of frame is declared when at least two
of four (or five) consecutive framing bits are in error.
|
| wfDs1E1TotalFramerStatsFeCounts |
.1.3.6.1.4.1.18.3.4.9.16.1.8 |
|
Framing error counts. In ESF mode this is the number of errored
superframes while in SF mode it is the number of incorrect framing
bits.
|
| wfDs1E1TotalFramerStatsLossFrameFailures |
.1.3.6.1.4.1.18.3.4.9.16.1.9 |
|
Loss of frame failures. These occur when an out of frame event or
carrier loss happens
|
| wfDs1E1TotalFramerStatsLossSignalFailures |
.1.3.6.1.4.1.18.3.4.9.16.1.10 |
|
Loss of Signal failure happen when receive carrier is lost
|
| wfDs1E1TotalFramerStatsAlarmIndicationFailures |
.1.3.6.1.4.1.18.3.4.9.16.1.11 |
|
Alarm Indication signal Failures occur when 2 consecutive frames have
less than 3 zeros (total) in the data stream.
|
| wfDs1E1TotalFramerStatsRemoteAlarmFailures |
.1.3.6.1.4.1.18.3.4.9.16.1.12 |
|
Remote alarm failure happen when the yellow alarm is detected
|
| wfDs1E1IntervalFramerStatsPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.17.1.1 |
|
Instance ID Slot, filled in by driver
|
| wfDs1E1IntervalFramerStatsIntervalNumber |
.1.3.6.1.4.1.18.3.4.9.17.1.2 |
|
Instance ID interval number, filled in by driver
|
| wfDs1E1IntervalFramerStatsMediaType |
.1.3.6.1.4.1.18.3.4.9.17.1.3 |
|
Media Type, T1 or E1
|
| wfDs1E1IntervalFramerStatsBpvCounts |
.1.3.6.1.4.1.18.3.4.9.17.1.4 |
|
bipolar violations counter
|
| wfDs1E1IntervalFramerStatsCrc4Counts |
.1.3.6.1.4.1.18.3.4.9.17.1.5 |
|
CRC4 error counter
|
| wfDs1E1IntervalFramerStatsFebeCounts |
.1.3.6.1.4.1.18.3.4.9.17.1.6 |
|
Far End Block Error counter
|
| wfDs1E1IntervalFramerStatsOofCounts |
.1.3.6.1.4.1.18.3.4.9.17.1.7 |
|
Out of frame error counts. Out of frame is declared when at least two
of four (or five) consecutive framing bits are in error.
|
| wfDs1E1IntervalFramerStatsFeCounts |
.1.3.6.1.4.1.18.3.4.9.17.1.8 |
|
Framing error counts. In ESF mode this is the number of errored
superframes while in SF mode it is the number of incorrect framing
bits.
|
| wfDs1E1IntervalFramerStatsLossFrameFailures |
.1.3.6.1.4.1.18.3.4.9.17.1.9 |
|
Loss of frame failures. These occur when an out of frame event or
carrier loss happens
|
| wfDs1E1IntervalFramerStatsLossSignalFailures |
.1.3.6.1.4.1.18.3.4.9.17.1.10 |
|
Loss of Signal failure happen when receive carrier is lost
|
| wfDs1E1IntervalFramerStatsAlarmIndicationFailures |
.1.3.6.1.4.1.18.3.4.9.17.1.11 |
|
Alarm Indication signal Failures occur when 2 consecutive frames have
less than 3 zeros (total) in the data stream.
|
| wfDs1E1IntervalFramerStatsRemoteAlarmFailures |
.1.3.6.1.4.1.18.3.4.9.17.1.12 |
|
Remote alarm failure happen when the yellow alarm is detected
|
| wfDs1E1ClockPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.18.1.2 |
|
The index ID for this record. It is the line number assigned
to a port in the wfDs1E1PortMapEntry for a port.connector pair.
Its channel field should be 0.
|
| wfDs1E1ClockDelete |
.1.3.6.1.4.1.18.3.4.9.18.1.1 |
|
Create/Delete attribute
|
| wfDs1E1ClockPrimaryClock |
.1.3.6.1.4.1.18.3.4.9.18.1.3 |
|
Specifies the primary source for transmit timing for this
port. The options for timing source are internal timing
source, loop timing from either port and an external timing
source. Note that the bit defines are equal to the Timing
Register bit definitions plus 1.
|
| wfDs1E1ClockSecondaryClock |
.1.3.6.1.4.1.18.3.4.9.18.1.4 |
|
Specifies the secondary source for transmit timing for this
port.
|
| wfDs1E1ClockCurrentClock |
.1.3.6.1.4.1.18.3.4.9.18.1.5 |
|
Specifies the current source for transmit timing for this
port.
|
| wfDs1E1ClockLoopClockOperational |
.1.3.6.1.4.1.18.3.4.9.18.1.6 |
|
Specifies this ports Loop Clock Status, PRESENT (UP) or
NOTPRESENT (DOWN).
|
| wfDs1E1ClockExtClockOperational |
.1.3.6.1.4.1.18.3.4.9.18.1.7 |
|
Indicates whether the External clock is operational.
|
| wfDs1E1LineCfgPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.21.1.5 |
|
Instance ID PortLineNumber, filled in by driver
|
| wfDs1E1LineCfgIndex |
.1.3.6.1.4.1.18.3.4.9.21.1.6 |
|
Index for this line instance, filled in by driver.
The index corresponds to the position of the
circuit on the port.
|
| wfDs1E1LineCfgDelete |
.1.3.6.1.4.1.18.3.4.9.21.1.1 |
|
Create/Delete parameter
|
| wfDs1E1LineCfgDisable |
.1.3.6.1.4.1.18.3.4.9.21.1.2 |
|
Enable/Disable parameter
|
| wfDs1E1LineCfgState |
.1.3.6.1.4.1.18.3.4.9.21.1.3 |
|
Line Driver state variable
|
| wfDs1E1LineLastChange |
.1.3.6.1.4.1.18.3.4.9.21.1.4 |
|
The value of sysUpTime at the time the interface entered
its current operational state.
|
| wfDs1E1LineCfgIfIndex |
.1.3.6.1.4.1.18.3.4.9.21.1.7 |
|
IfTable Index for this line instance,
filled in by driver.
|
| wfDs1E1LineCfgCct |
.1.3.6.1.4.1.18.3.4.9.21.1.8 |
|
Circuit number for this line instance
|
| wfDs1E1LineCfgLineNumber |
.1.3.6.1.4.1.18.3.4.9.21.1.9 |
|
LineNumber for this logical line instance. This is the same line number
contained in the PORT_TABLE with the channel field nonzero.
|
| wfDs1E1LineCfgQosServicePkg |
.1.3.6.1.4.1.18.3.4.9.21.1.10 |
|
Queue Service Package to be used for this line
|
| wfDs1E1LineCfgTimeSlotAssign |
.1.3.6.1.4.1.18.3.4.9.21.1.11 |
|
Bitmask of timeslot(s) assigned to this line
MSB == Bit 31, LSB == Bit 0
TimeSlot 1 == Bit 1
TimeSlot 24 == Bit 24 (T1)
TimeSlot 31 == Bit 31 (E1)
|
| wfDs1E1LineCfgActualTimeSlotAssign |
.1.3.6.1.4.1.18.3.4.9.21.1.12 |
|
Lists the time-slots which constitute this channel. Read only
attribute that contains a list of time-slots from 1 to 31
used by the channel
|
| wfDs1E1LineCfgWanProtocol |
.1.3.6.1.4.1.18.3.4.9.21.1.13 |
|
WAN protocol selection is provided via this parameter. The
supported protocols can be selected per circuit.
|
| wfDs1E1LineCfgRateAdaption |
.1.3.6.1.4.1.18.3.4.9.21.1.14 |
|
Determines the number of bits and their bit positions
within the time-slot. 64k selection uses all 8 bits in
the time-slot. The two 56k selections use 7 of the 8
bits in the time-slot. 56k_MSB does not use the most
significant bit and 56k_LSB does not use the least
significant bit in the time-slot.
|
| wfDs1E1LineCfgIFTF |
.1.3.6.1.4.1.18.3.4.9.21.1.15 |
|
Determines the Interframe time fill character to be
transmitted by the HDLC Controller. In case of IFTF_FLAGS,
0x7E is sent and in case of IFTF_IDLES 0xff is sent as the
interframe timefill characters.
|
| wfDs1E1LineCfgCRCSize |
.1.3.6.1.4.1.18.3.4.9.21.1.16 |
|
Determines the CRC Size. When CRC32 is selected a 32 bit
CRC is appended to the frame being transmitted and a 32
bit CRC check is performed on the received frame. When
CRC16 is selected, a 16 bit CRC is appended to the
transmitted frame and a 16 bit CRC is performed. on the
received frame.
|
| wfDs1E1LineCfgMtu |
.1.3.6.1.4.1.18.3.4.9.21.1.17 |
|
Specifies the largest frame size that can be received by the logical line.
Anything larger than the MTU will be discarded.
|
| wfDs1E1LineCfgBertMode |
.1.3.6.1.4.1.18.3.4.9.21.1.18 |
|
Enables Bit Error Rate Testing (BERT) on a logical line level.
|
| wfDs1E1LineCfgBertTestPattern |
.1.3.6.1.4.1.18.3.4.9.21.1.19 |
|
When a line is in BERT mode, it is capable of generating
a set of known patterns. This paramater selects between those
patterns
|
| wfDs1E1LineCfgFractionalLoopback |
.1.3.6.1.4.1.18.3.4.9.21.1.20 |
|
Any Ds1E1 Line on this T1/E1 port is capable of being put into
loopback through hardware, i.e. data coming into that circuit
from the wire is mirrorred back onto the wire. This parameter
enables or disables this loopback feature on any circuit.
|
| wfDs1E1LineCfgAcceptFracLoopCode |
.1.3.6.1.4.1.18.3.4.9.21.1.21 |
|
Allows logical line to accept Fractional T1 Loop Code sent
from a Remote Device.
|
| wfDs1E1LineCfgManagerMethod |
.1.3.6.1.4.1.18.3.4.9.21.1.22 |
|
This attribute has no affect on the Hardware configuration.
This attribute is purely for any Network Management Tool
to determine whether it configured the Logical Line as a
Clear Channel T1 or as a Fractional T1 with Timeslots.
|
| wfDs1E1LineStatPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.22.1.1 |
|
Instance ID PortLineNumber, filled in by driver
|
| wfDs1E1LineStatIndex |
.1.3.6.1.4.1.18.3.4.9.22.1.2 |
|
Index for this line instance, filled in by driver.
The index corresponds to the position of the
circuit, from 1 to 31, on the port.
|
| wfDs1E1LineStatRxOctets |
.1.3.6.1.4.1.18.3.4.9.22.1.3 |
|
Number of octets received without error
|
| wfDs1E1LineStatTxOctets |
.1.3.6.1.4.1.18.3.4.9.22.1.4 |
|
Number of octets transmitted without error
|
| wfDs1E1LineStatRxFrames |
.1.3.6.1.4.1.18.3.4.9.22.1.5 |
|
Number of frames received without error
|
| wfDs1E1LineStatTxFrames |
.1.3.6.1.4.1.18.3.4.9.22.1.6 |
|
Number of frames transmitted without error
|
| wfDs1E1LineStatRxErrors |
.1.3.6.1.4.1.18.3.4.9.22.1.7 |
|
Number of receive errors
|
| wfDs1E1LineStatTxErrors |
.1.3.6.1.4.1.18.3.4.9.22.1.8 |
|
Number of transmission errors
|
| wfDs1E1LineStatRxDropPackets |
.1.3.6.1.4.1.18.3.4.9.22.1.9 |
|
Number of Rx frames dropped
|
| wfDs1E1LineStatTxDropPackets |
.1.3.6.1.4.1.18.3.4.9.22.1.10 |
|
Number of Tx frames dropped
|
| wfDs1E1LineStatTxUnderflows |
.1.3.6.1.4.1.18.3.4.9.22.1.11 |
|
Number of Tx frames dropped due to Transmit underflow
|
| wfDs1E1LineStatRxOverflows |
.1.3.6.1.4.1.18.3.4.9.22.1.12 |
|
Number of Rx frames dropped due to Receive overflow
|
| wfDs1E1LineStatRxShortFrames |
.1.3.6.1.4.1.18.3.4.9.22.1.13 |
|
Number of short frames received whose length is either 1
or 2 data bytes.
|
| wfDs1E1LineStatRxCRCErrors |
.1.3.6.1.4.1.18.3.4.9.22.1.14 |
|
CRC error received
|
| wfDs1E1LineStatRxNonOctetBits |
.1.3.6.1.4.1.18.3.4.9.22.1.15 |
|
Non-Octet bits received in frame
|
| wfDs1E1LineStatRxLongFrames |
.1.3.6.1.4.1.18.3.4.9.22.1.16 |
|
Frame longer than MFL received
|
| wfDs1E1LineStatRxAbortFrames |
.1.3.6.1.4.1.18.3.4.9.22.1.17 |
|
Aborted frame received
|
| wfDs1E1DayCurrentPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.24.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1DayCurrentESs |
.1.3.6.1.4.1.18.3.4.9.24.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1DayCurrentSESs |
.1.3.6.1.4.1.18.3.4.9.24.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface
in the current day interval.'
|
| wfDs1E1DayCurrentSEFSs |
.1.3.6.1.4.1.18.3.4.9.24.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1
interface in the current day interval.
|
| wfDs1E1DayCurrentUASs |
.1.3.6.1.4.1.18.3.4.9.24.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1DayCurrentCSSs |
.1.3.6.1.4.1.18.3.4.9.24.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1DayCurrentPCVs |
.1.3.6.1.4.1.18.3.4.9.24.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1DayCurrentLESs |
.1.3.6.1.4.1.18.3.4.9.24.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
current day interval.'
|
| wfDs1E1DayCurrentBESs |
.1.3.6.1.4.1.18.3.4.9.24.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the current day interval.
|
| wfDs1E1DayCurrentDMs |
.1.3.6.1.4.1.18.3.4.9.24.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1DayCurrentLCVs |
.1.3.6.1.4.1.18.3.4.9.24.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1DayCurrentSASs |
.1.3.6.1.4.1.18.3.4.9.24.1.12 |
|
The number of seconds, within the current day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1DayCurrentAISSs |
.1.3.6.1.4.1.18.3.4.9.24.1.13 |
|
The number of seconds, within the current day interval,
containing one or more AIS defect.
|
| wfDs1E1DayCurrentFCs |
.1.3.6.1.4.1.18.3.4.9.24.1.14 |
|
The number of Path Failure Count error events detected
in the current day interval.
|
| wfDs1E1DayCurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.9.24.1.15 |
|
The number of seconds that have elapsed since the beginning of the
current error-measurement period.
|
| wfDs1E1DayCurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.9.24.1.16 |
|
The number of previous intervals for which valid data was collected. The
value will be 8 unless the interface was brought on-line within the last
8 days, in which case the value will be the number of complete day
intervals the since interface has been online.
|
| wfDs1E1DayCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.9.24.1.17 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1DayIntervalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.25.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1DayIntervalNumber |
.1.3.6.1.4.1.18.3.4.9.25.1.2 |
|
A number between 1 and 8, where 1 is the most recently completed day
interval and 8 is the least recently completed day interval (assuming
that all 8 intervals are valid).
|
| wfDs1E1DayIntervalESs |
.1.3.6.1.4.1.18.3.4.9.25.1.3 |
|
The number of Errored Seconds, encountered by a DS1 interface in the current
day interval.
|
| wfDs1E1DayIntervalSESs |
.1.3.6.1.4.1.18.3.4.9.25.1.4 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1DayIntervalSEFSs |
.1.3.6.1.4.1.18.3.4.9.25.1.5 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in one of the previous day intervals.
|
| wfDs1E1DayIntervalUASs |
.1.3.6.1.4.1.18.3.4.9.25.1.6 |
|
The number of Unavailable Seconds encountered by a DS1 interface in one of the
previous day intervals.
|
| wfDs1E1DayIntervalCSSs |
.1.3.6.1.4.1.18.3.4.9.25.1.7 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1DayIntervalPCVs |
.1.3.6.1.4.1.18.3.4.9.25.1.8 |
|
The number of Path Coding Violations encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1DayIntervalLESs |
.1.3.6.1.4.1.18.3.4.9.25.1.9 |
|
The number of Line Errored Seconds encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1DayIntervalBESs |
.1.3.6.1.4.1.18.3.4.9.25.1.10 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1DayIntervalDMs |
.1.3.6.1.4.1.18.3.4.9.25.1.11 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1DayIntervalLCVs |
.1.3.6.1.4.1.18.3.4.9.25.1.12 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1DayIntervalSASs |
.1.3.6.1.4.1.18.3.4.9.25.1.13 |
|
The number of seconds, in one of the previous day intervals,
containing one or more SEFs or AIS defects.
|
| wfDs1E1DayIntervalAISSs |
.1.3.6.1.4.1.18.3.4.9.25.1.14 |
|
The number of seconds, in one of the previous day intervals,
containing one or more AIS defect.
|
| wfDs1E1DayIntervalFCs |
.1.3.6.1.4.1.18.3.4.9.25.1.15 |
|
The number of Path Failure Count error events detected
one of the previous day intervals.
|
| wfDs1E1DayIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.9.25.1.16 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1DayTotalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.26.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1DayTotalESs |
.1.3.6.1.4.1.18.3.4.9.26.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalSESs |
.1.3.6.1.4.1.18.3.4.9.26.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalSEFSs |
.1.3.6.1.4.1.18.3.4.9.26.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1DayTotalUASs |
.1.3.6.1.4.1.18.3.4.9.26.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalCSSs |
.1.3.6.1.4.1.18.3.4.9.26.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalPCVs |
.1.3.6.1.4.1.18.3.4.9.26.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalLESs |
.1.3.6.1.4.1.18.3.4.9.26.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalBESs |
.1.3.6.1.4.1.18.3.4.9.26.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1DayTotalDMs |
.1.3.6.1.4.1.18.3.4.9.26.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1DayTotalLCVs |
.1.3.6.1.4.1.18.3.4.9.26.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the previous 8 day interval.
|
| wfDs1E1DayTotalSASs |
.1.3.6.1.4.1.18.3.4.9.26.1.12 |
|
The number of seconds, in the previous 8 day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1DayTotalAISSs |
.1.3.6.1.4.1.18.3.4.9.26.1.13 |
|
The number of seconds, in the previous 8 day interval,
containing one or more AIS defect.
|
| wfDs1E1DayTotalFCs |
.1.3.6.1.4.1.18.3.4.9.26.1.14 |
|
The number of Path Failure Count error events detected
in the previous 8 day interval.
|
| wfDs1E1DayTotalValidFlag |
.1.3.6.1.4.1.18.3.4.9.26.1.15 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndCurrentPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.27.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndCurrentESs |
.1.3.6.1.4.1.18.3.4.9.27.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndCurrentSESs |
.1.3.6.1.4.1.18.3.4.9.27.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface
in the current day interval.'
|
| wfDs1E1FarEndCurrentSEFSs |
.1.3.6.1.4.1.18.3.4.9.27.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1
interface in the current day interval.
|
| wfDs1E1FarEndCurrentUASs |
.1.3.6.1.4.1.18.3.4.9.27.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndCurrentCSSs |
.1.3.6.1.4.1.18.3.4.9.27.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndCurrentPCVs |
.1.3.6.1.4.1.18.3.4.9.27.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndCurrentLESs |
.1.3.6.1.4.1.18.3.4.9.27.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
current day interval.'
|
| wfDs1E1FarEndCurrentBESs |
.1.3.6.1.4.1.18.3.4.9.27.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the current day interval.
|
| wfDs1E1FarEndCurrentDMs |
.1.3.6.1.4.1.18.3.4.9.27.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1FarEndCurrentLCVs |
.1.3.6.1.4.1.18.3.4.9.27.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1FarEndCurrentSASs |
.1.3.6.1.4.1.18.3.4.9.27.1.12 |
|
The number of seconds, within the current day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndCurrentAISSs |
.1.3.6.1.4.1.18.3.4.9.27.1.13 |
|
The number of seconds, within the current day interval,
containing one or more AIS defect.
|
| wfDs1E1FarEndCurrentFCs |
.1.3.6.1.4.1.18.3.4.9.27.1.14 |
|
The number of Path Failure Count error events detected
in the current day interval.
|
| wfDs1E1FarEndCurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.9.27.1.15 |
|
The number of seconds that have elapsed since the beginning of the
current error-measurement period.
|
| wfDs1E1FarEndCurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.9.27.1.16 |
|
The number of previous intervals for which valid data was collected. The
value will be 8 unless the interface was brought on-line within the last
8 days, in which case the value will be the number of complete day
intervals the since interface has been online.
|
| wfDs1E1FarEndCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.9.27.1.17 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndIntervalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.28.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndIntervalNumber |
.1.3.6.1.4.1.18.3.4.9.28.1.2 |
|
A number between 1 and 8, where 1 is the most recently completed day
interval and 8 is the least recently completed day interval (assuming
that all 8 intervals are valid).
|
| wfDs1E1FarEndIntervalESs |
.1.3.6.1.4.1.18.3.4.9.28.1.3 |
|
The number of Errored Seconds, encountered by a DS1 interface in the current
day interval.
|
| wfDs1E1FarEndIntervalSESs |
.1.3.6.1.4.1.18.3.4.9.28.1.4 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1FarEndIntervalSEFSs |
.1.3.6.1.4.1.18.3.4.9.28.1.5 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in one of the previous day intervals.
|
| wfDs1E1FarEndIntervalUASs |
.1.3.6.1.4.1.18.3.4.9.28.1.6 |
|
The number of Unavailable Seconds encountered by a DS1 interface in one of the
previous day intervals.
|
| wfDs1E1FarEndIntervalCSSs |
.1.3.6.1.4.1.18.3.4.9.28.1.7 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1FarEndIntervalPCVs |
.1.3.6.1.4.1.18.3.4.9.28.1.8 |
|
The number of Path Coding Violations encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndIntervalLESs |
.1.3.6.1.4.1.18.3.4.9.28.1.9 |
|
The number of Line Errored Seconds encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndIntervalBESs |
.1.3.6.1.4.1.18.3.4.9.28.1.10 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1FarEndIntervalDMs |
.1.3.6.1.4.1.18.3.4.9.28.1.11 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndIntervalLCVs |
.1.3.6.1.4.1.18.3.4.9.28.1.12 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1FarEndIntervalSASs |
.1.3.6.1.4.1.18.3.4.9.28.1.13 |
|
The number of seconds, in one of the previous day intervals,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndIntervalAISSs |
.1.3.6.1.4.1.18.3.4.9.28.1.14 |
|
The number of seconds, in one of the previous day intervals,
containing one or more AIS defect.
|
| wfDs1E1FarEndIntervalFCs |
.1.3.6.1.4.1.18.3.4.9.28.1.15 |
|
The number of Path Failure Count error events detected
one of the previous day intervals.
|
| wfDs1E1FarEndIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.9.28.1.16 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndTotalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.29.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndTotalESs |
.1.3.6.1.4.1.18.3.4.9.29.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalSESs |
.1.3.6.1.4.1.18.3.4.9.29.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalSEFSs |
.1.3.6.1.4.1.18.3.4.9.29.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1FarEndTotalUASs |
.1.3.6.1.4.1.18.3.4.9.29.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalCSSs |
.1.3.6.1.4.1.18.3.4.9.29.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalPCVs |
.1.3.6.1.4.1.18.3.4.9.29.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalLESs |
.1.3.6.1.4.1.18.3.4.9.29.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalBESs |
.1.3.6.1.4.1.18.3.4.9.29.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1FarEndTotalDMs |
.1.3.6.1.4.1.18.3.4.9.29.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndTotalLCVs |
.1.3.6.1.4.1.18.3.4.9.29.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the previous 8 day interval.
|
| wfDs1E1FarEndTotalSASs |
.1.3.6.1.4.1.18.3.4.9.29.1.12 |
|
The number of seconds, in the previous 8 day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndTotalAISSs |
.1.3.6.1.4.1.18.3.4.9.29.1.13 |
|
The number of seconds, in the previous 8 day interval,
containing one or more AIS defect.
|
| wfDs1E1FarEndTotalFCs |
.1.3.6.1.4.1.18.3.4.9.29.1.14 |
|
The number of Path Failure Count error events detected
in the previous 8 day interval.
|
| wfDs1E1FarEndTotalValidFlag |
.1.3.6.1.4.1.18.3.4.9.29.1.15 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndDayCurrentPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.30.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndDayCurrentESs |
.1.3.6.1.4.1.18.3.4.9.30.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndDayCurrentSESs |
.1.3.6.1.4.1.18.3.4.9.30.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface
in the current day interval.'
|
| wfDs1E1FarEndDayCurrentSEFSs |
.1.3.6.1.4.1.18.3.4.9.30.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1
interface in the current day interval.
|
| wfDs1E1FarEndDayCurrentUASs |
.1.3.6.1.4.1.18.3.4.9.30.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndDayCurrentCSSs |
.1.3.6.1.4.1.18.3.4.9.30.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndDayCurrentPCVs |
.1.3.6.1.4.1.18.3.4.9.30.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
current day interval.
|
| wfDs1E1FarEndDayCurrentLESs |
.1.3.6.1.4.1.18.3.4.9.30.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
current day interval.'
|
| wfDs1E1FarEndDayCurrentBESs |
.1.3.6.1.4.1.18.3.4.9.30.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the current day interval.
|
| wfDs1E1FarEndDayCurrentDMs |
.1.3.6.1.4.1.18.3.4.9.30.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1FarEndDayCurrentLCVs |
.1.3.6.1.4.1.18.3.4.9.30.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the current day interval.'
|
| wfDs1E1FarEndDayCurrentSASs |
.1.3.6.1.4.1.18.3.4.9.30.1.12 |
|
The number of seconds, within the current day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndDayCurrentAISSs |
.1.3.6.1.4.1.18.3.4.9.30.1.13 |
|
The number of seconds, within the current day interval,
containing one or more AIS defect.
|
| wfDs1E1FarEndDayCurrentFCs |
.1.3.6.1.4.1.18.3.4.9.30.1.14 |
|
The number of Path Failure Count error events detected
in the current day interval.
|
| wfDs1E1FarEndDayCurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.9.30.1.15 |
|
The number of seconds that have elapsed since the beginning of the
current error-measurement period.
|
| wfDs1E1FarEndDayCurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.9.30.1.16 |
|
The number of previous intervals for which valid data was collected. The
value will be 8 unless the interface was brought on-line within the last
8 days, in which case the value will be the number of complete day
intervals the since interface has been online.
|
| wfDs1E1FarEndDayCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.9.30.1.17 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndDayIntervalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.31.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndDayIntervalNumber |
.1.3.6.1.4.1.18.3.4.9.31.1.2 |
|
A number between 1 and 8, where 1 is the most recently completed day
interval and 8 is the least recently completed day interval (assuming
that all 8 intervals are valid).
|
| wfDs1E1FarEndDayIntervalESs |
.1.3.6.1.4.1.18.3.4.9.31.1.3 |
|
The number of Errored Seconds, encountered by a DS1 interface in the current
day interval.
|
| wfDs1E1FarEndDayIntervalSESs |
.1.3.6.1.4.1.18.3.4.9.31.1.4 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalSEFSs |
.1.3.6.1.4.1.18.3.4.9.31.1.5 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in one of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalUASs |
.1.3.6.1.4.1.18.3.4.9.31.1.6 |
|
The number of Unavailable Seconds encountered by a DS1 interface in one of the
previous day intervals.
|
| wfDs1E1FarEndDayIntervalCSSs |
.1.3.6.1.4.1.18.3.4.9.31.1.7 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in one
of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalPCVs |
.1.3.6.1.4.1.18.3.4.9.31.1.8 |
|
The number of Path Coding Violations encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndDayIntervalLESs |
.1.3.6.1.4.1.18.3.4.9.31.1.9 |
|
The number of Line Errored Seconds encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndDayIntervalBESs |
.1.3.6.1.4.1.18.3.4.9.31.1.10 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalDMs |
.1.3.6.1.4.1.18.3.4.9.31.1.11 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in one of
the previous day intervals.
|
| wfDs1E1FarEndDayIntervalLCVs |
.1.3.6.1.4.1.18.3.4.9.31.1.12 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
one of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalSASs |
.1.3.6.1.4.1.18.3.4.9.31.1.13 |
|
The number of seconds, in one of the previous day intervals,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndDayIntervalAISSs |
.1.3.6.1.4.1.18.3.4.9.31.1.14 |
|
The number of seconds, in one of the previous day intervals,
containing one or more AIS defect.
|
| wfDs1E1FarEndDayIntervalFCs |
.1.3.6.1.4.1.18.3.4.9.31.1.15 |
|
The number of Path Failure Count error events detected
one of the previous day intervals.
|
| wfDs1E1FarEndDayIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.9.31.1.16 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1FarEndDayTotalPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.32.1.1 |
|
The instance ID that identifies the port. The port line number with a zero
channel number field as found in the port map table.
|
| wfDs1E1FarEndDayTotalESs |
.1.3.6.1.4.1.18.3.4.9.32.1.2 |
|
The number of Errored Seconds, encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalSESs |
.1.3.6.1.4.1.18.3.4.9.32.1.3 |
|
The number of Severely Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalSEFSs |
.1.3.6.1.4.1.18.3.4.9.32.1.4 |
|
The number of Severely Errored Framing Seconds encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1FarEndDayTotalUASs |
.1.3.6.1.4.1.18.3.4.9.32.1.5 |
|
The number of Unavailable Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalCSSs |
.1.3.6.1.4.1.18.3.4.9.32.1.6 |
|
The number of Controlled Slip Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalPCVs |
.1.3.6.1.4.1.18.3.4.9.32.1.7 |
|
The number of Path Coding Violations encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalLESs |
.1.3.6.1.4.1.18.3.4.9.32.1.8 |
|
The number of Line Errored Seconds encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalBESs |
.1.3.6.1.4.1.18.3.4.9.32.1.9 |
|
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface
in the previous 8 day interval.
|
| wfDs1E1FarEndDayTotalDMs |
.1.3.6.1.4.1.18.3.4.9.32.1.10 |
|
The number of Degraded Minutes (DMs) encountered by a DS1 interface in the
previous 8 day interval.
|
| wfDs1E1FarEndDayTotalLCVs |
.1.3.6.1.4.1.18.3.4.9.32.1.11 |
|
The number of Line Code Violations (LCVs) encountered by a DS1 interface in
the previous 8 day interval.
|
| wfDs1E1FarEndDayTotalSASs |
.1.3.6.1.4.1.18.3.4.9.32.1.12 |
|
The number of seconds, in the previous 8 day interval,
containing one or more SEFs or AIS defects.
|
| wfDs1E1FarEndDayTotalAISSs |
.1.3.6.1.4.1.18.3.4.9.32.1.13 |
|
The number of seconds, in the previous 8 day interval,
containing one or more AIS defect.
|
| wfDs1E1FarEndDayTotalFCs |
.1.3.6.1.4.1.18.3.4.9.32.1.14 |
|
The number of Path Failure Count error events detected
in the previous 8 day interval.
|
| wfDs1E1FarEndDayTotalValidFlag |
.1.3.6.1.4.1.18.3.4.9.32.1.15 |
|
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
| wfDs1E1ThrAlrtPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.33.1.2 |
|
The instance ID that identifies the port.
|
| wfDs1E1ThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.9.33.1.1 |
|
Create/Delete parameter
|
| wfDs1E1ThrAlrtESs |
.1.3.6.1.4.1.18.3.4.9.33.1.3 |
|
The number of Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtSESs |
.1.3.6.1.4.1.18.3.4.9.33.1.4 |
|
The number of Severely Errored Seconds which must be received prior
to the generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.9.33.1.5 |
|
The number of Severely Errored Framing Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.9.33.1.6 |
|
The number of Unavailable Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtCSSs |
.1.3.6.1.4.1.18.3.4.9.33.1.7 |
|
The number of Controlled Slip Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.9.33.1.8 |
|
The number of Path Coding Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.9.33.1.9 |
|
The number of Line Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtBESs |
.1.3.6.1.4.1.18.3.4.9.33.1.10 |
|
The number of Bursty Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtDMs |
.1.3.6.1.4.1.18.3.4.9.33.1.11 |
|
The number of Degraded Minutes which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.9.33.1.12 |
|
The number of Line Code Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.9.33.1.13 |
|
The number of SEF/AIS Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.9.33.1.14 |
|
The number of AIS defect Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1ThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.9.33.1.15 |
|
The number of Path Failure Counts which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.34.1.2 |
|
The instance ID that identifies the port.
|
| wfDs1E1DayThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.9.34.1.1 |
|
Create/Delete parameter
|
| wfDs1E1DayThrAlrtESs |
.1.3.6.1.4.1.18.3.4.9.34.1.3 |
|
The number of Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtSESs |
.1.3.6.1.4.1.18.3.4.9.34.1.4 |
|
The number of Severely Errored Seconds which must be received prior
to the generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.9.34.1.5 |
|
The number of Severely Errored Framing Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.9.34.1.6 |
|
The number of Unavailable Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtCSSs |
.1.3.6.1.4.1.18.3.4.9.34.1.7 |
|
The number of Controlled Slip Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.9.34.1.8 |
|
The number of Path Coding Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.9.34.1.9 |
|
The number of Line Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtBESs |
.1.3.6.1.4.1.18.3.4.9.34.1.10 |
|
The number of Bursty Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtDMs |
.1.3.6.1.4.1.18.3.4.9.34.1.11 |
|
The number of Degraded Minutes which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.9.34.1.12 |
|
The number of Line Code Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.9.34.1.13 |
|
The number of SEF/AIS Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.9.34.1.14 |
|
The number of AIS defect Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1DayThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.9.34.1.15 |
|
The number of Path Failure Counts which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.35.1.2 |
|
The instance ID that identifies the port.
|
| wfDs1E1FarEndThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.9.35.1.1 |
|
Create/Delete parameter
|
| wfDs1E1FarEndThrAlrtESs |
.1.3.6.1.4.1.18.3.4.9.35.1.3 |
|
The number of Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtSESs |
.1.3.6.1.4.1.18.3.4.9.35.1.4 |
|
The number of Severely Errored Seconds which must be received prior
to the generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.9.35.1.5 |
|
The number of Severely Errored Framing Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.9.35.1.6 |
|
The number of Unavailable Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtCSSs |
.1.3.6.1.4.1.18.3.4.9.35.1.7 |
|
The number of Controlled Slip Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.9.35.1.8 |
|
The number of Path Coding Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.9.35.1.9 |
|
The number of Line Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtBESs |
.1.3.6.1.4.1.18.3.4.9.35.1.10 |
|
The number of Bursty Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtDMs |
.1.3.6.1.4.1.18.3.4.9.35.1.11 |
|
The number of Degraded Minutes which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.9.35.1.12 |
|
The number of Line Code Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.9.35.1.13 |
|
The number of SEF/AIS Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.9.35.1.14 |
|
The number of AIS defect Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.9.35.1.15 |
|
The number of Path Failure Counts which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.36.1.2 |
|
The instance ID that identifies the port.
|
| wfDs1E1FarEndDayThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.9.36.1.1 |
|
Create/Delete parameter
|
| wfDs1E1FarEndDayThrAlrtESs |
.1.3.6.1.4.1.18.3.4.9.36.1.3 |
|
The number of Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtSESs |
.1.3.6.1.4.1.18.3.4.9.36.1.4 |
|
The number of Severely Errored Seconds which must be received prior
to the generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.9.36.1.5 |
|
The number of Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.9.36.1.6 |
|
The number of Unavailable Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtCSSs |
.1.3.6.1.4.1.18.3.4.9.36.1.7 |
|
The number of Controlled Slip Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.9.36.1.8 |
|
The number of Path Coding Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.9.36.1.9 |
|
The number of Line Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtBESs |
.1.3.6.1.4.1.18.3.4.9.36.1.10 |
|
The number of Bursty Errored Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtDMs |
.1.3.6.1.4.1.18.3.4.9.36.1.11 |
|
The number of Degraded Minutes which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.9.36.1.12 |
|
The number of Line Code Violations which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.9.36.1.13 |
|
The number of SEF/AIS Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.9.36.1.14 |
|
The number of AIS defect Seconds which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1FarEndDayThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.9.36.1.15 |
|
The number of Path Failure Counts which must be received prior to the
generation of a Threshold Crossing Alert.
|
| wfDs1E1LineQueStatPortLineNumber |
.1.3.6.1.4.1.18.3.4.9.20.1.1 |
|
Instance ID PortLineNumber
|
| wfDs1E1LineQueStatLineIndex |
.1.3.6.1.4.1.18.3.4.9.20.1.2 |
|
Instance Line Number
|
| wfDs1E1LineQueStatQueueIndex |
.1.3.6.1.4.1.18.3.4.9.20.1.3 |
|
Queue Index, matches that of wfQosServPkgQueCfgQueueIndex or
one for best effort.
|
| wfDs1E1LineQueStatTxOctets |
.1.3.6.1.4.1.18.3.4.9.20.1.4 |
|
Number of Transmit Octets received by the Queue without error
|
| wfDs1E1LineQueStatTxPackets |
.1.3.6.1.4.1.18.3.4.9.20.1.5 |
|
Number of Transmit Packets received by the Queue without error
|
| wfDs1E1LineQueStatTxDrops |
.1.3.6.1.4.1.18.3.4.9.20.1.6 |
|
Number of Transmit Packets Dropped by the Queue
|
