wfDsx3LineIndex |
.1.3.6.1.4.1.18.3.4.26.1.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3IfIndex |
.1.3.6.1.4.1.18.3.4.26.1.1.2 |
this is value of ifIndex from the Interfaces table of
MIB II (RFC 1213).
|
wfDsx3TimeElapsed |
.1.3.6.1.4.1.18.3.4.26.1.1.3 |
0..899 seconds elapsed within the current 15-minute interval
|
wfDsx3ValidIntervals |
.1.3.6.1.4.1.18.3.4.26.1.1.4 |
0..96 previous intervals that valid data were collected.
This is 96 unless the device was brought on line within
the last 24 hours.
|
wfDsx3LineType |
.1.3.6.1.4.1.18.3.4.26.1.1.5 |
the variety of DS3/E3 application implementing this circuit
|
wfDsx3LineCoding |
.1.3.6.1.4.1.18.3.4.26.1.1.6 |
the variety of Zero Code Suppression used on the link
|
wfDsx3SendCode |
.1.3.6.1.4.1.18.3.4.26.1.1.7 |
the type of code being sent across the DS3/E3 circuit by
the device
|
wfDsx3CircuitIdentifier |
.1.3.6.1.4.1.18.3.4.26.1.1.8 |
the transmission vendor's circuit identifier
|
wfDsx3LoopbackConfig |
.1.3.6.1.4.1.18.3.4.26.1.1.9 |
the loopback configuration of the DS3/E3 interface
|
wfDsx3LineStatus |
.1.3.6.1.4.1.18.3.4.26.1.1.10 |
the status of the DS3/E3 line
|
wfDsx3TransmitClockSource |
.1.3.6.1.4.1.18.3.4.26.1.1.11 |
the source of Transmit Clock for the DS3/E3 interface
|
wfDsx3CurrentIndex |
.1.3.6.1.4.1.18.3.4.26.2.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3CurrentPESs |
.1.3.6.1.4.1.18.3.4.26.2.1.2 |
the number of P-bit Errored Seconds in the current interval
|
wfDsx3CurrentPSESs |
.1.3.6.1.4.1.18.3.4.26.2.1.3 |
the number of P-bit Severely Errored Seconds in the
current interval
|
wfDsx3CurrentSEFSs |
.1.3.6.1.4.1.18.3.4.26.2.1.4 |
the number of Severely Errored Framing Seconds in the
current interval
|
wfDsx3CurrentUASs |
.1.3.6.1.4.1.18.3.4.26.2.1.5 |
the number of Unavailable Seconds in the current interval
|
wfDsx3CurrentLCVs |
.1.3.6.1.4.1.18.3.4.26.2.1.6 |
the number of Line Coding Violations in the current interval
|
wfDsx3CurrentPCVs |
.1.3.6.1.4.1.18.3.4.26.2.1.7 |
the number of P-bit Coding Violations in the current interval
|
wfDsx3CurrentLESs |
.1.3.6.1.4.1.18.3.4.26.2.1.8 |
the number of Line Errored Seconds in the current interval
|
wfDsx3CurrentCCVs |
.1.3.6.1.4.1.18.3.4.26.2.1.9 |
the number of C-bit Coding Violations in the current interval
|
wfDsx3CurrentCESs |
.1.3.6.1.4.1.18.3.4.26.2.1.10 |
the number of C-bit Errored Seconds in the current interval
|
wfDsx3CurrentCSESs |
.1.3.6.1.4.1.18.3.4.26.2.1.11 |
the number of C-bit Severely Errored Seconds
in the current interval
|
wfDsx3CurrentSASs |
.1.3.6.1.4.1.18.3.4.26.2.1.12 |
the number of Seconds containing one or more SEFs or AIS defects
in the current interval
|
wfDsx3CurrentAISSs |
.1.3.6.1.4.1.18.3.4.26.2.1.13 |
the number of Seconds containing one or more AIS defect
in the current interval
|
wfDsx3CurrentFCs |
.1.3.6.1.4.1.18.3.4.26.2.1.14 |
the number of Path Failure Count error events detected
in the current interval
|
wfDsx3CurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.26.2.1.15 |
the number of seconds since the beginning of
the far end current interval
|
wfDsx3CurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.26.2.1.16 |
the number of previous far end intervals for
which valid data is available
|
wfDsx3CurrentValidFlag |
.1.3.6.1.4.1.18.3.4.26.2.1.17 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3IntervalIndex |
.1.3.6.1.4.1.18.3.4.26.3.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3IntervalNumber |
.1.3.6.1.4.1.18.3.4.26.3.1.2 |
1..96 where 1 is the most recent 15-minute interval and 96 is
the least
|
wfDsx3IntervalPESs |
.1.3.6.1.4.1.18.3.4.26.3.1.3 |
the number of P-bit Errored Seconds in the specified interval
|
wfDsx3IntervalPSESs |
.1.3.6.1.4.1.18.3.4.26.3.1.4 |
the number of P-bit Severely Errored Seconds in the
specified interval
|
wfDsx3IntervalSEFSs |
.1.3.6.1.4.1.18.3.4.26.3.1.5 |
the number of Severely Errored Framing Seconds in the
specified interval
|
wfDsx3IntervalUASs |
.1.3.6.1.4.1.18.3.4.26.3.1.6 |
the number of Unavailable Seconds in the specified interval
|
wfDsx3IntervalLCVs |
.1.3.6.1.4.1.18.3.4.26.3.1.7 |
the number of Line Coding Violations in the specified interval
|
wfDsx3IntervalPCVs |
.1.3.6.1.4.1.18.3.4.26.3.1.8 |
the number of P-bit Coding Violations in the specified interval
|
wfDsx3IntervalLESs |
.1.3.6.1.4.1.18.3.4.26.3.1.9 |
the number of Line Errored Seconds in the specified interval
|
wfDsx3IntervalCCVs |
.1.3.6.1.4.1.18.3.4.26.3.1.10 |
the number of C-bit Coding Violations in the specified interval
|
wfDsx3IntervalCESs |
.1.3.6.1.4.1.18.3.4.26.3.1.11 |
the number of C-bit Errored Seconds in the specified interval
|
wfDsx3IntervalCSESs |
.1.3.6.1.4.1.18.3.4.26.3.1.12 |
the number of C-bit Severely Errored Seconds
in the specified interval
|
wfDsx3IntervalSASs |
.1.3.6.1.4.1.18.3.4.26.3.1.13 |
the number of Seconds containing one or more SEFs or AIS defects
in the specified interval
|
wfDsx3IntervalAISSs |
.1.3.6.1.4.1.18.3.4.26.3.1.14 |
the number of Seconds containing one or more AIS defect
in the specified interval
|
wfDsx3IntervalFCs |
.1.3.6.1.4.1.18.3.4.26.3.1.15 |
the number of Path Failure Count error events detected
in the specified interval
|
wfDsx3IntervalValidFlag |
.1.3.6.1.4.1.18.3.4.26.3.1.16 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3TotalIndex |
.1.3.6.1.4.1.18.3.4.26.4.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3TotalPESs |
.1.3.6.1.4.1.18.3.4.26.4.1.2 |
the number of P-bit Errored Seconds in the last 24 hours
|
wfDsx3TotalPSESs |
.1.3.6.1.4.1.18.3.4.26.4.1.3 |
the number of P-bit Severely Errored Seconds in the
last 24 hours
|
wfDsx3TotalSEFSs |
.1.3.6.1.4.1.18.3.4.26.4.1.4 |
the number of Severely Errored Framing Seconds in the
last 24 hours
|
wfDsx3TotalUASs |
.1.3.6.1.4.1.18.3.4.26.4.1.5 |
the number of Unavailable Seconds in the last 24 hours
|
wfDsx3TotalLCVs |
.1.3.6.1.4.1.18.3.4.26.4.1.6 |
the number of Line Coding Violations in the last 24 hours
|
wfDsx3TotalPCVs |
.1.3.6.1.4.1.18.3.4.26.4.1.7 |
the number of P-bit Coding Violations in the last 24 hours
|
wfDsx3TotalLESs |
.1.3.6.1.4.1.18.3.4.26.4.1.8 |
the number of Line Errored Seconds in the last 24 hours
|
wfDsx3TotalCCVs |
.1.3.6.1.4.1.18.3.4.26.4.1.9 |
the number of C-bit Coding Violations in the last 24 hours
|
wfDsx3TotalCESs |
.1.3.6.1.4.1.18.3.4.26.4.1.10 |
the number of C-bit Errored Seconds in the last 24 hours
|
wfDsx3TotalCSESs |
.1.3.6.1.4.1.18.3.4.26.4.1.11 |
the number of C-bit Severely Errored Seconds
in the last 24 hours
|
wfDsx3TotalSASs |
.1.3.6.1.4.1.18.3.4.26.4.1.12 |
the number of Seconds containing one or more SEFs or AIS defects
in the last 24 hours
|
wfDsx3TotalAISSs |
.1.3.6.1.4.1.18.3.4.26.4.1.13 |
the number of Seconds containing one or more AIS defect
in the last 24 hours
|
wfDsx3TotalFCs |
.1.3.6.1.4.1.18.3.4.26.4.1.14 |
the number of Path Failure Count error events detected
in the last 24 hours
|
wfDsx3TotalValidFlag |
.1.3.6.1.4.1.18.3.4.26.4.1.15 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndLineIndex |
.1.3.6.1.4.1.18.3.4.26.5.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndEquipCode |
.1.3.6.1.4.1.18.3.4.26.5.1.2 |
equipment description code - C-bit parity only
|
wfDsx3FarEndLocationIDCode |
.1.3.6.1.4.1.18.3.4.26.5.1.3 |
equipment location code - C-bit parity only
|
wfDsx3FarEndFrameIDCode |
.1.3.6.1.4.1.18.3.4.26.5.1.4 |
code for the equipment location within a building
|
wfDsx3FarEndUnitCode |
.1.3.6.1.4.1.18.3.4.26.5.1.5 |
code for the equipment location within a bay
|
wfDsx3FarEndFacilityIDCode |
.1.3.6.1.4.1.18.3.4.26.5.1.6 |
path identification code
|
wfDsx3FarEndCurrentIndex |
.1.3.6.1.4.1.18.3.4.26.6.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndTimeElapsed |
.1.3.6.1.4.1.18.3.4.26.6.1.2 |
the number of seconds since the beginning of
the far end current interval
|
wfDsx3FarEndValidIntervals |
.1.3.6.1.4.1.18.3.4.26.6.1.3 |
the number of previous far end intervals for
which valid data is available
|
wfDsx3FarEndCurrentCESs |
.1.3.6.1.4.1.18.3.4.26.6.1.4 |
the number of C-bit Errored Seconds in
the current far end interval
|
wfDsx3FarEndCurrentCSESs |
.1.3.6.1.4.1.18.3.4.26.6.1.5 |
the number of C-bit Severely Errored Seconds
in the current far end interval
|
wfDsx3FarEndCurrentCCVs |
.1.3.6.1.4.1.18.3.4.26.6.1.6 |
the number of C-bit Coding Violations
in the current far end interval
|
wfDsx3FarEndCurrentUASs |
.1.3.6.1.4.1.18.3.4.26.6.1.7 |
the number of Unavailable Seconds
in the current far end interval
|
wfDsx3FarEndCurrentSASs |
.1.3.6.1.4.1.18.3.4.26.6.1.8 |
the number of Seconds containing one or more SEFs or AIS defects
in the current far end interval
|
wfDsx3FarEndCurrentFCs |
.1.3.6.1.4.1.18.3.4.26.6.1.9 |
the number of Path Failure Count error events detected
in the current far end interval
|
wfDsx3FarEndCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.26.6.1.10 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndIntervalIndex |
.1.3.6.1.4.1.18.3.4.26.7.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndIntervalNumber |
.1.3.6.1.4.1.18.3.4.26.7.1.2 |
1..96 where 1 is the most recent 15-minute interval and 96 is
the least
|
wfDsx3FarEndIntervalCESs |
.1.3.6.1.4.1.18.3.4.26.7.1.3 |
the count of C-bit Errored Seconds in the specified interval
|
wfDsx3FarEndIntervalCSESs |
.1.3.6.1.4.1.18.3.4.26.7.1.4 |
the count of C-bit Severely Errored Seconds in the
specified interval
|
wfDsx3FarEndIntervalCCVs |
.1.3.6.1.4.1.18.3.4.26.7.1.5 |
the count of C-bit Code Violation error events in the
specified interval
|
wfDsx3FarEndIntervalUASs |
.1.3.6.1.4.1.18.3.4.26.7.1.6 |
the count of Unavailable Seconds in the specified interval
|
wfDsx3FarEndIntervalSASs |
.1.3.6.1.4.1.18.3.4.26.7.1.7 |
the number of Seconds containing one or more SEFs or AIS defects
in the specified far end interval
|
wfDsx3FarEndIntervalFCs |
.1.3.6.1.4.1.18.3.4.26.7.1.8 |
the number of Path Failure Count error events detected
in the specified far end interval
|
wfDsx3FarEndIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.26.7.1.9 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndTotalIndex |
.1.3.6.1.4.1.18.3.4.26.8.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndTotalCESs |
.1.3.6.1.4.1.18.3.4.26.8.1.2 |
total count of C-bit Errored Seconds
|
wfDsx3FarEndTotalCSESs |
.1.3.6.1.4.1.18.3.4.26.8.1.3 |
total count of C-bit Severely Errored Seconds
|
wfDsx3FarEndTotalCCVs |
.1.3.6.1.4.1.18.3.4.26.8.1.4 |
total count of C-bit Code Violation error events
|
wfDsx3FarEndTotalUASs |
.1.3.6.1.4.1.18.3.4.26.8.1.5 |
total count of Unavailable Seconds
|
wfDsx3FarEndTotalSASs |
.1.3.6.1.4.1.18.3.4.26.8.1.6 |
the number of Seconds containing one or more SEFs or AIS defects
at the far end in the last 24 hours.
|
wfDsx3FarEndTotalFCs |
.1.3.6.1.4.1.18.3.4.26.8.1.7 |
the number of Path Failure Count error events detected
at the far end in the last 24 hours.
|
wfDsx3FarEndTotalValidFlag |
.1.3.6.1.4.1.18.3.4.26.8.1.8 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfAtmInterfaceDs3PlcpIndex |
.1.3.6.1.4.1.18.3.4.26.9.1.1 |
this corresponds to the Wellfleet circuit number
|
wfAtmInterfaceDs3PlcpSEFSs |
.1.3.6.1.4.1.18.3.4.26.9.1.2 |
the number of DS3 PLCP Severely Errored Framing Second (SEFS)
|
wfAtmInterfaceDs3PlcpAlarmState |
.1.3.6.1.4.1.18.3.4.26.9.1.3 |
the state of the DS3 PLCP
|
wfAtmInterfaceDs3PlcpUASs |
.1.3.6.1.4.1.18.3.4.26.9.1.4 |
the number of Unavailable Seconds encountered by the PLCP
|
wfDsx3DayCurrentIndex |
.1.3.6.1.4.1.18.3.4.26.11.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3DayCurrentPESs |
.1.3.6.1.4.1.18.3.4.26.11.1.2 |
the number of P-bit Errored Seconds in the current interval
|
wfDsx3DayCurrentPSESs |
.1.3.6.1.4.1.18.3.4.26.11.1.3 |
the number of P-bit Severely Errored Seconds in the
current interval
|
wfDsx3DayCurrentSEFSs |
.1.3.6.1.4.1.18.3.4.26.11.1.4 |
the number of Severely Errored Framing Seconds in the
current interval
|
wfDsx3DayCurrentUASs |
.1.3.6.1.4.1.18.3.4.26.11.1.5 |
the number of Unavailable Seconds in the current interval
|
wfDsx3DayCurrentLCVs |
.1.3.6.1.4.1.18.3.4.26.11.1.6 |
the number of Line Coding Violations in the current interval
|
wfDsx3DayCurrentPCVs |
.1.3.6.1.4.1.18.3.4.26.11.1.7 |
the number of P-bit Coding Violations in the current interval
|
wfDsx3DayCurrentLESs |
.1.3.6.1.4.1.18.3.4.26.11.1.8 |
the number of Line Errored Seconds in the current interval
|
wfDsx3DayCurrentCCVs |
.1.3.6.1.4.1.18.3.4.26.11.1.9 |
the number of C-bit Coding Violations in the current interval
|
wfDsx3DayCurrentCESs |
.1.3.6.1.4.1.18.3.4.26.11.1.10 |
the number of C-bit Errored Seconds in the current interval
|
wfDsx3DayCurrentCSESs |
.1.3.6.1.4.1.18.3.4.26.11.1.11 |
the number of C-bit Severely Errored Seconds
in the current interval
|
wfDsx3DayCurrentSASs |
.1.3.6.1.4.1.18.3.4.26.11.1.12 |
the number of Seconds containing one or more SEFs or AIS defects
in the current interval
|
wfDsx3DayCurrentAISSs |
.1.3.6.1.4.1.18.3.4.26.11.1.13 |
the number of Seconds containing one or more AIS defect
in the current interval
|
wfDsx3DayCurrentFCs |
.1.3.6.1.4.1.18.3.4.26.11.1.14 |
the number of Path Failure Count error events detected
in the current interval
|
wfDsx3DayCurrentTimeElapsed |
.1.3.6.1.4.1.18.3.4.26.11.1.15 |
the number of seconds since the beginning of
the far end current interval
|
wfDsx3DayCurrentValidIntervals |
.1.3.6.1.4.1.18.3.4.26.11.1.16 |
the number of previous far end intervals for
which valid data is available
|
wfDsx3DayCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.26.11.1.17 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3DayIntervalIndex |
.1.3.6.1.4.1.18.3.4.26.12.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3DayIntervalNumber |
.1.3.6.1.4.1.18.3.4.26.12.1.2 |
1..96 where 1 is the most recent 15-minute interval and 96 is
the least
|
wfDsx3DayIntervalPESs |
.1.3.6.1.4.1.18.3.4.26.12.1.3 |
the number of P-bit Errored Seconds in the specified interval
|
wfDsx3DayIntervalPSESs |
.1.3.6.1.4.1.18.3.4.26.12.1.4 |
the number of P-bit Severely Errored Seconds in the
specified interval
|
wfDsx3DayIntervalSEFSs |
.1.3.6.1.4.1.18.3.4.26.12.1.5 |
the number of Severely Errored Framing Seconds in the
specified interval
|
wfDsx3DayIntervalUASs |
.1.3.6.1.4.1.18.3.4.26.12.1.6 |
the number of Unavailable Seconds in the specified interval
|
wfDsx3DayIntervalLCVs |
.1.3.6.1.4.1.18.3.4.26.12.1.7 |
the number of Line Coding Violations in the specified interval
|
wfDsx3DayIntervalPCVs |
.1.3.6.1.4.1.18.3.4.26.12.1.8 |
the number of P-bit Coding Violations in the specified interval
|
wfDsx3DayIntervalLESs |
.1.3.6.1.4.1.18.3.4.26.12.1.9 |
the number of Line Errored Seconds in the specified interval
|
wfDsx3DayIntervalCCVs |
.1.3.6.1.4.1.18.3.4.26.12.1.10 |
the number of C-bit Coding Violations in the specified interval
|
wfDsx3DayIntervalCESs |
.1.3.6.1.4.1.18.3.4.26.12.1.11 |
the number of C-bit Errored Seconds in the specified interval
|
wfDsx3DayIntervalCSESs |
.1.3.6.1.4.1.18.3.4.26.12.1.12 |
the number of C-bit Severely Errored Seconds
in the specified interval
|
wfDsx3DayIntervalSASs |
.1.3.6.1.4.1.18.3.4.26.12.1.13 |
the number of Seconds containing one or more SEFs or AIS defects
in the specified interval
|
wfDsx3DayIntervalAISSs |
.1.3.6.1.4.1.18.3.4.26.12.1.14 |
the number of Seconds containing one or more AIS defect
in the specified interval
|
wfDsx3DayIntervalFCs |
.1.3.6.1.4.1.18.3.4.26.12.1.15 |
the number of Path Failure Count error events detected
in the specified interval
|
wfDsx3DayIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.26.12.1.16 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3DayTotalIndex |
.1.3.6.1.4.1.18.3.4.26.13.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3DayTotalPESs |
.1.3.6.1.4.1.18.3.4.26.13.1.2 |
the number of P-bit Errored Seconds in the last 24 hours
|
wfDsx3DayTotalPSESs |
.1.3.6.1.4.1.18.3.4.26.13.1.3 |
the number of P-bit Severely Errored Seconds in the
last 24 hours
|
wfDsx3DayTotalSEFSs |
.1.3.6.1.4.1.18.3.4.26.13.1.4 |
the number of Severely Errored Framing Seconds in the
last 24 hours
|
wfDsx3DayTotalUASs |
.1.3.6.1.4.1.18.3.4.26.13.1.5 |
the number of Unavailable Seconds in the last 24 hours
|
wfDsx3DayTotalLCVs |
.1.3.6.1.4.1.18.3.4.26.13.1.6 |
the number of Line Coding Violations in the last 24 hours
|
wfDsx3DayTotalPCVs |
.1.3.6.1.4.1.18.3.4.26.13.1.7 |
the number of P-bit Coding Violations in the last 24 hours
|
wfDsx3DayTotalLESs |
.1.3.6.1.4.1.18.3.4.26.13.1.8 |
the number of Line Errored Seconds in the last 24 hours
|
wfDsx3DayTotalCCVs |
.1.3.6.1.4.1.18.3.4.26.13.1.9 |
the number of C-bit Coding Violations in the last 24 hours
|
wfDsx3DayTotalCESs |
.1.3.6.1.4.1.18.3.4.26.13.1.10 |
the number of C-bit Errored Seconds in the last 24 hours
|
wfDsx3DayTotalCSESs |
.1.3.6.1.4.1.18.3.4.26.13.1.11 |
the number of C-bit Severely Errored Seconds
in the last 24 hours
|
wfDsx3DayTotalSASs |
.1.3.6.1.4.1.18.3.4.26.13.1.12 |
the number of Seconds containing one or more SEFs or AIS defects
in the last 24 hours
|
wfDsx3DayTotalAISSs |
.1.3.6.1.4.1.18.3.4.26.13.1.13 |
the number of Seconds containing one or more AIS defect
in the last 24 hours
|
wfDsx3DayTotalFCs |
.1.3.6.1.4.1.18.3.4.26.13.1.14 |
the number of Path Failure Count error events detected
in the last 24 hours
|
wfDsx3DayTotalValidFlag |
.1.3.6.1.4.1.18.3.4.26.13.1.15 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndDayCurrentIndex |
.1.3.6.1.4.1.18.3.4.26.14.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndDayTimeElapsed |
.1.3.6.1.4.1.18.3.4.26.14.1.2 |
the number of seconds since the beginning of
the far end current interval
|
wfDsx3FarEndDayValidIntervals |
.1.3.6.1.4.1.18.3.4.26.14.1.3 |
the number of previous far end intervals for
which valid data is available
|
wfDsx3FarEndDayCurrentCESs |
.1.3.6.1.4.1.18.3.4.26.14.1.4 |
the number of C-bit Errored Seconds in
the current far end interval
|
wfDsx3FarEndDayCurrentCSESs |
.1.3.6.1.4.1.18.3.4.26.14.1.5 |
the number of C-bit Severely Errored Seconds
in the current far end interval
|
wfDsx3FarEndDayCurrentCCVs |
.1.3.6.1.4.1.18.3.4.26.14.1.6 |
the number of C-bit Coding Violations
in the current far end interval
|
wfDsx3FarEndDayCurrentUASs |
.1.3.6.1.4.1.18.3.4.26.14.1.7 |
the number of Unavailable Seconds
in the current far end interval
|
wfDsx3FarEndDayCurrentSASs |
.1.3.6.1.4.1.18.3.4.26.14.1.8 |
the number of Seconds containing one or more SEFs or AIS defects
in the current far end interval
|
wfDsx3FarEndDayCurrentFCs |
.1.3.6.1.4.1.18.3.4.26.14.1.9 |
the number of Path Failure Count error events detected
in the current far end interval
|
wfDsx3FarEndDayCurrentValidFlag |
.1.3.6.1.4.1.18.3.4.26.14.1.10 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndDayIntervalIndex |
.1.3.6.1.4.1.18.3.4.26.15.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndDayIntervalNumber |
.1.3.6.1.4.1.18.3.4.26.15.1.2 |
1..96 where 1 is the most recent 15-minute interval and 96 is
the least
|
wfDsx3FarEndDayIntervalCESs |
.1.3.6.1.4.1.18.3.4.26.15.1.3 |
the count of C-bit Errored Seconds in the specified interval
|
wfDsx3FarEndDayIntervalCSESs |
.1.3.6.1.4.1.18.3.4.26.15.1.4 |
the count of C-bit Severely Errored Seconds in the
specified interval
|
wfDsx3FarEndDayIntervalCCVs |
.1.3.6.1.4.1.18.3.4.26.15.1.5 |
the count of C-bit Code Violation error events in the
specified interval
|
wfDsx3FarEndDayIntervalUASs |
.1.3.6.1.4.1.18.3.4.26.15.1.6 |
the count of Unavailable Seconds in the specified interval
|
wfDsx3FarEndDayIntervalSASs |
.1.3.6.1.4.1.18.3.4.26.15.1.7 |
the number of Seconds containing one or more SEFs or AIS defects
in the specified far end interval
|
wfDsx3FarEndDayIntervalFCs |
.1.3.6.1.4.1.18.3.4.26.15.1.8 |
the number of Path Failure Count error events detected
in the specified far end interval
|
wfDsx3FarEndDayIntervalValidFlag |
.1.3.6.1.4.1.18.3.4.26.15.1.9 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3FarEndDayTotalIndex |
.1.3.6.1.4.1.18.3.4.26.16.1.1 |
this corresponds to the Wellfleet circuit number
|
wfDsx3FarEndDayTotalCESs |
.1.3.6.1.4.1.18.3.4.26.16.1.2 |
total count of C-bit Errored Seconds
|
wfDsx3FarEndDayTotalCSESs |
.1.3.6.1.4.1.18.3.4.26.16.1.3 |
total count of C-bit Severely Errored Seconds
|
wfDsx3FarEndDayTotalCCVs |
.1.3.6.1.4.1.18.3.4.26.16.1.4 |
total count of C-bit Code Violation error events
|
wfDsx3FarEndDayTotalUASs |
.1.3.6.1.4.1.18.3.4.26.16.1.5 |
total count of Unavailable Seconds
|
wfDsx3FarEndDayTotalSASs |
.1.3.6.1.4.1.18.3.4.26.16.1.6 |
the number of Seconds containing one or more SEFs or AIS defects
at the far end in the last 24 hours.
|
wfDsx3FarEndDayTotalFCs |
.1.3.6.1.4.1.18.3.4.26.16.1.7 |
the number of Path Failure Count error events detected
at the far end in the last 24 hours.
|
wfDsx3FarEndDayTotalValidFlag |
.1.3.6.1.4.1.18.3.4.26.16.1.8 |
Indicates whether this interval reported by the Mib Table is valid or
invalid.
|
wfDsx3ThrAlrtIndex |
.1.3.6.1.4.1.18.3.4.26.18.1.2 |
The instance ID that identifies the port.
|
wfDsx3ThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.26.18.1.1 |
Create/Delete parameter
|
wfDsx3ThrAlrtPESs |
.1.3.6.1.4.1.18.3.4.26.18.1.3 |
The number of P-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtPSESs |
.1.3.6.1.4.1.18.3.4.26.18.1.4 |
The number of P-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.26.18.1.5 |
The number of Severely Errored Framing Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.26.18.1.6 |
The number of Unavailable Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.26.18.1.7 |
The number of Line Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.26.18.1.8 |
The number of P-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.26.18.1.9 |
The number of Line Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtCCVs |
.1.3.6.1.4.1.18.3.4.26.18.1.10 |
The number of C-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtCESs |
.1.3.6.1.4.1.18.3.4.26.18.1.11 |
The number of C-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtCSESs |
.1.3.6.1.4.1.18.3.4.26.18.1.12 |
The number of C-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.26.18.1.13 |
The number of SEF/AIS Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.26.18.1.14 |
The number of AIS defect Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3ThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.26.18.1.15 |
The number of Path Failure Counts which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtIndex |
.1.3.6.1.4.1.18.3.4.26.19.1.2 |
The instance ID that identifies the port.
|
wfDsx3FarEndThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.26.19.1.1 |
Create/Delete parameter
|
wfDsx3FarEndThrAlrtCESs |
.1.3.6.1.4.1.18.3.4.26.19.1.3 |
The number of C-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtCSESs |
.1.3.6.1.4.1.18.3.4.26.19.1.4 |
The number of C-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtCCVs |
.1.3.6.1.4.1.18.3.4.26.19.1.5 |
The number of C-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.26.19.1.6 |
The number of Unavailable Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.26.19.1.7 |
The number of SEF/AIS Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.26.19.1.8 |
The number of Path Failure Counts which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtIndex |
.1.3.6.1.4.1.18.3.4.26.20.1.2 |
The instance ID that identifies the port.
|
wfDsx3DayThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.26.20.1.1 |
Create/Delete parameter
|
wfDsx3DayThrAlrtPESs |
.1.3.6.1.4.1.18.3.4.26.20.1.3 |
The number of P-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtPSESs |
.1.3.6.1.4.1.18.3.4.26.20.1.4 |
The number of P-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtSEFSs |
.1.3.6.1.4.1.18.3.4.26.20.1.5 |
The number of Severely Errored Framing Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.26.20.1.6 |
The number of Unavailable Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtLCVs |
.1.3.6.1.4.1.18.3.4.26.20.1.7 |
The number of Line Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtPCVs |
.1.3.6.1.4.1.18.3.4.26.20.1.8 |
The number of P-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtLESs |
.1.3.6.1.4.1.18.3.4.26.20.1.9 |
The number of Line Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtCCVs |
.1.3.6.1.4.1.18.3.4.26.20.1.10 |
The number of C-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtCESs |
.1.3.6.1.4.1.18.3.4.26.20.1.11 |
The number of C-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtCSESs |
.1.3.6.1.4.1.18.3.4.26.20.1.12 |
The number of C-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.26.20.1.13 |
The number of SEF/AIS Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtAISSs |
.1.3.6.1.4.1.18.3.4.26.20.1.14 |
The number of AIS defect Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3DayThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.26.20.1.15 |
The number of Path Failure Counts which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtIndex |
.1.3.6.1.4.1.18.3.4.26.21.1.2 |
The instance ID that identifies the port.
|
wfDsx3FarEndDayThrAlrtDelete |
.1.3.6.1.4.1.18.3.4.26.21.1.1 |
Create/Delete parameter
|
wfDsx3FarEndDayThrAlrtCESs |
.1.3.6.1.4.1.18.3.4.26.21.1.3 |
The number of C-bit Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtCSESs |
.1.3.6.1.4.1.18.3.4.26.21.1.4 |
The number of C-bit Severely Errored Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtCCVs |
.1.3.6.1.4.1.18.3.4.26.21.1.5 |
The number of C-bit Coding Violations which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtUASs |
.1.3.6.1.4.1.18.3.4.26.21.1.6 |
The number of Unavailable Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtSASs |
.1.3.6.1.4.1.18.3.4.26.21.1.7 |
The number of SEF/AIS Seconds which must be received
prior to the generation of a Threshold Crossing Alert.
|
wfDsx3FarEndDayThrAlrtFCs |
.1.3.6.1.4.1.18.3.4.26.21.1.8 |
The number of Path Failure Counts which must be received
prior to the generation of a Threshold Crossing Alert.
|