| wfHssiSlot |
.1.3.6.1.4.1.18.3.4.7.1.4 |
|
Instance ID Slot, filled in by driver
|
| wfHssiConnector |
.1.3.6.1.4.1.18.3.4.7.1.5 |
|
Instance ID Connector, filled in by driver
|
| wfHssiDelete |
.1.3.6.1.4.1.18.3.4.7.1.1 |
|
Create/Delete parameter
|
| wfHssiDisable |
.1.3.6.1.4.1.18.3.4.7.1.2 |
|
Enable/Disable parameter
|
| wfHssiState |
.1.3.6.1.4.1.18.3.4.7.1.3 |
|
Line Driver state variable, Not Present, Init, Down, Up
|
| wfHssiCct |
.1.3.6.1.4.1.18.3.4.7.1.6 |
|
CCT number for this line instance
|
| wfHssiBofl |
.1.3.6.1.4.1.18.3.4.7.1.7 |
|
breath of life parameter
|
| wfHssiBoflTmo |
.1.3.6.1.4.1.18.3.4.7.1.8 |
|
breath of life frequency in seconds
|
| wfHssiMtu |
.1.3.6.1.4.1.18.3.4.7.1.9 |
|
MTU parameter, this is buffer size for HSSI media, fixed
|
| wfHssiMadr |
.1.3.6.1.4.1.18.3.4.7.1.10 |
|
Line MAC address, fixed - line driver fills in from the 48 bit
address stored in the serial number prom for this connector.
|
| wfHssiService |
.1.3.6.1.4.1.18.3.4.7.1.11 |
|
Service type for this circuit. Transparent is raw HDLC mode, and is the
only service provided on the current HSSI product
|
| wfHssiWanProtocol |
.1.3.6.1.4.1.18.3.4.7.1.12 |
|
WAN protocol selection is provided via this parameter. The
supported protocols can be selected per interface.
|
| wfHssiTransmissionInterface |
.1.3.6.1.4.1.18.3.4.7.1.13 |
|
T1 or T3, in the future OC1, OC3 and OC12. Used for MIB selection
|
| wfHssiExternalClkSpeed |
.1.3.6.1.4.1.18.3.4.7.1.14 |
|
External Clock Speed, Used in the future for route selection
|
| wfHssiCrcSize |
.1.3.6.1.4.1.18.3.4.7.1.15 |
|
CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC
|
| wfHssiInternalClkTestMode |
.1.3.6.1.4.1.18.3.4.7.1.16 |
|
Enables internal transmit clock generation. Should NEVER be enabled for
normal operation.
|
| wfHssiRxOctets |
.1.3.6.1.4.1.18.3.4.7.1.17 |
|
Number of bytes received without error
|
| wfHssiRxFrames |
.1.3.6.1.4.1.18.3.4.7.1.18 |
|
Number of frames received without error
|
| wfHssiTxOctets |
.1.3.6.1.4.1.18.3.4.7.1.19 |
|
Number of bytes transmitted without error
|
| wfHssiTxFrames |
.1.3.6.1.4.1.18.3.4.7.1.20 |
|
Number of frames transmitted without error
|
| wfHssiInDiscards |
.1.3.6.1.4.1.18.3.4.7.1.21 |
|
Number of error-free inbound packets discarded. Usually due to lack of
memory resources.
|
| wfHssiInErrors |
.1.3.6.1.4.1.18.3.4.7.1.22 |
|
Number of inbound packets not delivered to higher-layer protocol because
of errors.
|
| wfHssiOutDiscards |
.1.3.6.1.4.1.18.3.4.7.1.23 |
|
Number of error-free outbound packets discarded. Usually due to lack of
transmission bandwidth.
|
| wfHssiOutErrors |
.1.3.6.1.4.1.18.3.4.7.1.24 |
|
Number of outbound packets that could not be transmitted because of
errors.
|
| wfHssiRxLongFrames |
.1.3.6.1.4.1.18.3.4.7.1.25 |
|
Number of Long frames dropped on receive because of length
|
| wfHssiTxClipFrames |
.1.3.6.1.4.1.18.3.4.7.1.26 |
|
Number of frames clipped in the transmit routine
|
| wfHssiRxReplenMisses |
.1.3.6.1.4.1.18.3.4.7.1.27 |
|
Number of failed attempts by the line driver to aquire a packet buffer
|
| wfHssiLastRxErrorCtrl |
.1.3.6.1.4.1.18.3.4.7.1.28 |
|
Last errored receive descriptor's control field
|
| wfHssiRxCrcErrors |
.1.3.6.1.4.1.18.3.4.7.1.29 |
|
Number of frames received with CRC errors
|
| wfHssiRxOverruns |
.1.3.6.1.4.1.18.3.4.7.1.30 |
|
Number of frames received with fifo overrun errors
|
| wfHssiRxAborts |
.1.3.6.1.4.1.18.3.4.7.1.31 |
|
Number of frames received with abort status
|
| wfHssiLastTxErrorCtrl |
.1.3.6.1.4.1.18.3.4.7.1.32 |
|
Last errored transmit descriptor's control field
|
| wfHssiTxAborts |
.1.3.6.1.4.1.18.3.4.7.1.33 |
|
Number of transmit frames with internal abort errors
|
| wfHssiTxUnderruns |
.1.3.6.1.4.1.18.3.4.7.1.34 |
|
Number of transmit frames aborted with underrun errors
|
| wfHssiRxRingErrors |
.1.3.6.1.4.1.18.3.4.7.1.35 |
|
Number of receive ring error events
|
| wfHssiLastRxRingState |
.1.3.6.1.4.1.18.3.4.7.1.36 |
|
Last 8 bit value from the recv ring state register
|
| wfHssiRxRingOverruns |
.1.3.6.1.4.1.18.3.4.7.1.37 |
|
Number of receive ring overrun events
|
| wfHssiTxRingErrors |
.1.3.6.1.4.1.18.3.4.7.1.38 |
|
Number of transmit ring error events
|
| wfHssiLastTxRingState |
.1.3.6.1.4.1.18.3.4.7.1.39 |
|
Last 8 bit value from the transmit ring state register
|
| wfHssiPortOpErrors |
.1.3.6.1.4.1.18.3.4.7.1.40 |
|
Number of port operation error events
|
| wfHssiInternOpErrors |
.1.3.6.1.4.1.18.3.4.7.1.41 |
|
Number of internal operation error events
|
| wfHssiHostErrors |
.1.3.6.1.4.1.18.3.4.7.1.42 |
|
Number of parity errs on host accesses to directly accessable registers.
|
| wfHssiRxProcessings |
.1.3.6.1.4.1.18.3.4.7.1.43 |
|
Number of receive frame processings (RINT)
|
| wfHssiTxProcessings |
.1.3.6.1.4.1.18.3.4.7.1.44 |
|
Number of transmit processings, invokations of transmit routine
|
| wfHssiTxCmplProcessings |
.1.3.6.1.4.1.18.3.4.7.1.45 |
|
Number of transmit complete processings (TINT)
|
| wfHssiIntrProcessings |
.1.3.6.1.4.1.18.3.4.7.1.46 |
|
Number of Interrupt processings, invokations of intr routine
|
| wfHssiBoflNum |
.1.3.6.1.4.1.18.3.4.7.1.47 |
|
Number of breath of life packets per breath of life
|
| wfHssiBoflLen |
.1.3.6.1.4.1.18.3.4.7.1.48 |
|
breath of life packet length
|
| wfHssiRxBufferLength |
.1.3.6.1.4.1.18.3.4.7.1.49 |
|
Performance tunning parameter controls Receive buffer size.
|
| wfHssiMemPageLength |
.1.3.6.1.4.1.18.3.4.7.1.50 |
|
Performance tunning parameter controls device memory access burst length.
|
| wfHssiRxRingLength |
.1.3.6.1.4.1.18.3.4.7.1.51 |
|
Current Receive Queue Length.
|
| wfHssiTxRingLength |
.1.3.6.1.4.1.18.3.4.7.1.52 |
|
Current Transmit Queue Length.
|
| wfHssiRxFifoWatermark |
.1.3.6.1.4.1.18.3.4.7.1.53 |
|
Performance tunning parameter controls the receive watermark.
|
| wfHssiTxFifoWatermark |
.1.3.6.1.4.1.18.3.4.7.1.54 |
|
Performance tunning parameter controls the transmit watermark.
|
| wfHssiMaxRxMemory |
.1.3.6.1.4.1.18.3.4.7.1.55 |
|
Performance tunning parameter controls fifo area allowed for receive.
|
| wfHssiLinkInterface |
.1.3.6.1.4.1.18.3.4.7.1.56 |
|
Only for DEBUG.
|
| wfHssiTurboBofl |
.1.3.6.1.4.1.18.3.4.7.1.57 |
|
Only for DEBUG, Turbo breath of life parameter
|
| wfHssiCfgRxQueueLength |
.1.3.6.1.4.1.18.3.4.7.1.58 |
|
Configured Receive Queue Length. Values other than zero over-ride the
router selected values. A value of zero has a special meaning. Zero
causes router based default values to be used. Values larger than the
compiled ring size are truncated to the compiled ring size.
|
| wfHssiCfgTxQueueLength |
.1.3.6.1.4.1.18.3.4.7.1.59 |
|
Configured Transmit Queue Length. Values other than zero over-ride the
router selected values. A value of zero has a special meaning. Zero
causes router based default values to be used. Values larger than the
compiled ring size are truncated to the compiled ring size.
|
| wfHssiLineNumber |
.1.3.6.1.4.1.18.3.4.7.1.60 |
|
line number for this line instance
|
| wfHssiCfgCngstCtlEnable |
.1.3.6.1.4.1.18.3.4.7.1.61 |
|
Configured Congestion Control Enable. Enable or disable BNX switch
congestion control on this HSSI port. Note that this has relevance only
in the BNX switch and (currently) Frame Relay and SMDS switching
functionality. If enabled, congestion control will monitor the levels of
traffic and congestion and mark and drop certain packets as per of
Frame Relay or SMDS protocols. See BNX doc for details on the
congestion control strategy.
|
| wfHssiLastChange |
.1.3.6.1.4.1.18.3.4.7.1.62 |
|
The value of SysUpTime at the time the interface entered it's current
operational state (UP state). SysUpTime is defined as the time (in
hundredths of a second) since the network management portion of the
system was last re-initialized. Usually the time since boot.
|
| wfHssiOutQLen |
.1.3.6.1.4.1.18.3.4.7.1.63 |
|
The instantaneous current length of the output packet queue (in packets).
|
| wfHssiCarrLossDebounceTmo |
.1.3.6.1.4.1.18.3.4.7.1.64 |
|
This attribute determines how many seconds to wait before
transitioning to the Carrier Lost state when the Carrier Signal
is lost. When set to 0 (default), the Driver will immediately
transition to the lost state upon detecting Carrier Loss. If
the Carrier Signal returns prior to reaching this threshold,
the Driver will not enter the Carrier Lost state at all.
|
| wfHssiModule |
.1.3.6.1.4.1.18.3.4.7.1.65 |
|
Module number for ASN platform, filled in by driver. For
non-ASN platforms this attribute will not be used.
|
| wfHssiActualConnector |
.1.3.6.1.4.1.18.3.4.7.1.66 |
|
Actual connector number for ASN platform, filled in
by driver. For non-ASN platforms, this attribute will
not be used.
|
| wfHssiLoopback |
.1.3.6.1.4.1.18.3.4.7.1.67 |
|
Loopback type requested, Local Digital (Loop A), Local Line
(Loop B), Remote Line (Loop C), or none
|
| wfHssiReceiveAllFrames |
.1.3.6.1.4.1.18.3.4.7.1.68 |
|
This attribute enables delivery of all receive frames to the
HSSI device driver for processing. When disabled, frames
less than 4 bytes in length are filtered out of the receive
frame stream before reaching the device driver.
It is necessary to enable the attribute when running Frame Relay
switched virtual circuits (SVC) in order to allow the reception
of 3 byte frames.
|
