| wfIpxBasicSysInstance |
.1.3.6.1.4.1.18.3.5.5.15.1.4 |
|
The unique identifier for the instance of IPX.
|
| wfIpxBasicSysDelete |
.1.3.6.1.4.1.18.3.5.5.15.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete IPX.
|
| wfIpxBasicSysDisable |
.1.3.6.1.4.1.18.3.5.5.15.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable IPX.
|
| wfIpxBasicSysState |
.1.3.6.1.4.1.18.3.5.5.15.1.3 |
|
The current state of the entire IPX Router.
|
| wfIpxBasicSysPrimaryNetworkNumber |
.1.3.6.1.4.1.18.3.5.5.15.1.5 |
|
The 'internal' network number, used for IPXWAN
|
| wfIpxBasicSysMultipleHostAddresses |
.1.3.6.1.4.1.18.3.5.5.15.1.6 |
|
Allow the user to configure one host/mac addr for the whole box (default)
where, if configured, the CfgHostAddress is used (becomes HostAddress)
otherwise if left unconfigured the Host address is discerned from the
backplane serial number. If Multiple host is Enabled and the host number is
configured in the interface record the configured value is used as the
hostid/mac addr of the interface (except Token Ring which can't go into
promiscous mode, uses Token Ring Mac as hostid/mac of interface). If the
host number in left unconfigured then the hostid/mac is gotten from the
mac of the circuit.
|
| wfIpxBasicSysCfgHostAddress |
.1.3.6.1.4.1.18.3.5.5.15.1.7 |
|
Host Number of Router and potential MAC address of box.
This host number will be used to overide the default
box generated host address.
|
| wfIpxBasicSysHostAddress |
.1.3.6.1.4.1.18.3.5.5.15.1.8 |
|
Host Number of Router and potential MAC address of box.
This is not a restart variable because this will be
filled in from the IPX code after reading it from
either the configurable host number or from a box
generated variable.
|
| wfIpxBasicSysRouterName |
.1.3.6.1.4.1.18.3.5.5.15.1.9 |
|
The Name of the Router, used for IPXWAN
|
| wfIpxBasicSysInReceives |
.1.3.6.1.4.1.18.3.5.5.15.1.10 |
|
The total number of IPX packets received, including errors
|
| wfIpxBasicSysInHdrErrors |
.1.3.6.1.4.1.18.3.5.5.15.1.11 |
|
The number of IPX packets discarded due to errors in
their headers, including any IPX packet with a size less
than the minimum of 30 bytes
|
| wfIpxBasicSysInUnknownSockets |
.1.3.6.1.4.1.18.3.5.5.15.1.12 |
|
The number of IPX packets discarded because the
destination was the router and the socket was not known
|
| wfIpxBasicSysInDiscards |
.1.3.6.1.4.1.18.3.5.5.15.1.13 |
|
The number of IPX packets received but discarded due to
reasons other than those accounted for by
wfIpxBasicSysInHdrErrors , wfIpxBasicSysInUnknownSockets,
wfIpxBasicSysAdvSysInDiscards, and wfIpxAdvSysInCompressDiscards
|
| wfIpxBasicSysInBadChecksums |
.1.3.6.1.4.1.18.3.5.5.15.1.14 |
|
The number of IPX packets received with incorrect checksums
|
| wfIpxBasicSysInDelivers |
.1.3.6.1.4.1.18.3.5.5.15.1.15 |
|
The number of IPX packets delivered locally
|
| wfIpxBasicSysNoRoutes |
.1.3.6.1.4.1.18.3.5.5.15.1.16 |
|
The number of times no route to a destination was found
|
| wfIpxBasicSysOutRequests |
.1.3.6.1.4.1.18.3.5.5.15.1.17 |
|
The number of IPX packets supplied locally for
transmission, not including any packets counted in
wfIpxAdvSysForwPackets
|
| wfIpxBasicSysOutMalformedRequests |
.1.3.6.1.4.1.18.3.5.5.15.1.18 |
|
The number of outgoing IPX packets discarded due to
reasons other than those accounted for in
wfIpxBasicSysOutMalformedRequest, wfIpxAdvSysOutFiltered,
and wfIpxAdvSysOutCompressDiscards
|
| wfIpxBasicSysOutPackets |
.1.3.6.1.4.1.18.3.5.5.15.1.19 |
|
The total number of IPX packets transmitted
|
| wfIpxBasicSysOpenEncapsFails |
.1.3.6.1.4.1.18.3.5.5.15.1.20 |
|
The number of IPX encaps open calls which failed
|
| wfIpxBasicSysOutDiscards |
.1.3.6.1.4.1.18.3.5.5.15.1.21 |
|
The number of outgoing IPX packets discarded due to
reasons other than those accounted for by
wfIpxBasicSysOutMalformedRequests,
wfIpxBasicSysAdvSysOutFiltered, and wfIpxAdvSysOutCompressDiscards
|
| wfIpxAdvSysInstance |
.1.3.6.1.4.1.18.3.5.5.16.1.2 |
|
The unique identifier for the instance of IPX.
|
| wfIpxAdvSysDelete |
.1.3.6.1.4.1.18.3.5.5.16.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete the IPX
advanced system group.
|
| wfIpxAdvSysRoutingMethod |
.1.3.6.1.4.1.18.3.5.5.16.1.3 |
|
Choose either Tick or Hop based routing
|
| wfIpxAdvSysLogFilter |
.1.3.6.1.4.1.18.3.5.5.16.1.4 |
|
Filter out some log messages, Default filters out
trace messages.
|
| wfIpxAdvSysMaximumPath |
.1.3.6.1.4.1.18.3.5.5.16.1.5 |
|
Declare Maximum number of paths stored for a given destination
network
|
| wfIpxAdvSysMaxPathSplits |
.1.3.6.1.4.1.18.3.5.5.16.1.6 |
|
A non-zero value enables load sharing between equal cost
paths with the best metric when forwarding packets
|
| wfIpxAdvSysMaxHops |
.1.3.6.1.4.1.18.3.5.5.16.1.7 |
|
The maximum number of hops a packet may take
|
| wfIpxAdvSysInTooManyHops |
.1.3.6.1.4.1.18.3.5.5.16.1.8 |
|
The number of IPX packets discarded due to exceeding the
maximum hop count.
|
| wfIpxAdvSysInFiltered |
.1.3.6.1.4.1.18.3.5.5.16.1.9 |
|
The number of incoming IPX packets discarded due to
filtering, not including those counted in
wfIpxTrafficFilterCounter
|
| wfIpxAdvSysInCompressDiscards |
.1.3.6.1.4.1.18.3.5.5.16.1.10 |
|
Then number of incoming IPX packets discarded due to
decompression errors.
|
| wfIpxAdvSysNETBIOSPackets |
.1.3.6.1.4.1.18.3.5.5.16.1.11 |
|
The number of NETBIOS packets received
|
| wfIpxAdvSysForwPackets |
.1.3.6.1.4.1.18.3.5.5.16.1.12 |
|
The number of IPX packets forwarded
|
| wfIpxAdvSysOutFiltered |
.1.3.6.1.4.1.18.3.5.5.16.1.13 |
|
The number of outgoing IPX packets discarded due to filtering
|
| wfIpxAdvSysOutCompressDiscards |
.1.3.6.1.4.1.18.3.5.5.16.1.14 |
|
The number of outgoing IPX packets discarded due to
compression errors
|
| wfIpxAdvSysNovellCertificationConformanceDisable |
.1.3.6.1.4.1.18.3.5.5.16.1.15 |
|
enable/disable Novell certification, disable/enable Wellfleet specifics
|
| wfIpxAdvSysCircCount |
.1.3.6.1.4.1.18.3.5.5.16.1.16 |
|
The number of IPX Circuits (interfaces).
|
| wfIpxAdvSysCfgDestCount |
.1.3.6.1.4.1.18.3.5.5.16.1.17 |
|
A value indicating the maximum destinations (networks) that
the user expects the router to learn. This is used to
pre-allocate table sizes for network tables. Changing this
value can greatly effect the memory used by IPX, however it
can also speed learning times.
|
| wfIpxAdvSysDestCount |
.1.3.6.1.4.1.18.3.5.5.16.1.18 |
|
The number of currently reachable destinations known to IPX
|
| wfIpxAdvSysCfgServCount |
.1.3.6.1.4.1.18.3.5.5.16.1.19 |
|
A value indicating the maximum services that the user
expects the router to learn. This is used to pre-allocate
table sizes for service tables. Changing this value
can greatly effect the memory used by IPX, however it
can also speed learning times.
|
| wfIpxAdvSysServCount |
.1.3.6.1.4.1.18.3.5.5.16.1.20 |
|
The number of currently reachable services known to IPX
|
| wfIpxAdvSysCfgHostCount |
.1.3.6.1.4.1.18.3.5.5.16.1.21 |
|
A value indicating the maximum next hop hosts that the user
expects the router to learn. This is used to pre-allocate
table sizes for host tables. Changing this value
can greatly effect the memory used by IPX, however it
can also speed learning times.
|
| wfIpxAdvSysHostCount |
.1.3.6.1.4.1.18.3.5.5.16.1.22 |
|
The number of currently reachable hosts known to IPX
|
| wfIpxAdvSysAgingFrequency |
.1.3.6.1.4.1.18.3.5.5.16.1.23 |
|
The frequency, in seconds, for aging RIP and SAP
information.
|
| wfIpxAdvSysAgingPendingFrequency |
.1.3.6.1.4.1.18.3.5.5.16.1.24 |
|
The number of routes and services to age before pending.
|
| wfIpxAdvSysDefaultRouteEnable |
.1.3.6.1.4.1.18.3.5.5.16.1.25 |
|
This parameter indicates whether or not default route is used
for unknown networks.
|
| wfIpxAdvSysSapViaDefaultRouteEnable |
.1.3.6.1.4.1.18.3.5.5.16.1.26 |
|
This parameter indicates whether or not a SAP advertisement
can be learned from an interface if the network number advertised
in the SAP advertisement is unreachable but default route is
accessible from that interface. Note that the router may not be
compatible with other router implementations when this feature is
enabled.
|
| wfIpxAdvSysCT |
.1.3.6.1.4.1.18.3.5.5.16.1.27 |
|
The NLSP Certification Test compatibility flag.
|
| wfIpxAdvSysMibReplySlots |
.1.3.6.1.4.1.18.3.5.5.16.1.28 |
|
The slots running IPX which should reply to MIB
Proxy requests
|
| wfIpxAdvSysGNSRespMode |
.1.3.6.1.4.1.18.3.5.5.16.1.29 |
|
Algorithm used to determine the server to choose when
responding to a Get Nearest Server Request
|
| wfIpxAdvSysMaxNetTblSize |
.1.3.6.1.4.1.18.3.5.5.16.1.30 |
|
maximum allowed size of the network table
|
| wfIpxAdvSysNetTblFillNotify |
.1.3.6.1.4.1.18.3.5.5.16.1.31 |
|
notify when (configured) percentage is reached
|
| wfIpxAdvSysGlobalTrigUpdate |
.1.3.6.1.4.1.18.3.5.5.16.1.32 |
|
enable/disable triggered rip/sap updates box wide.
|
| wfIpxCircSysInstance |
.1.3.6.1.4.1.18.3.5.5.17.1.4 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxCircIndex |
.1.3.6.1.4.1.18.3.5.5.17.1.5 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxCircDelete |
.1.3.6.1.4.1.18.3.5.5.17.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxCircDisable |
.1.3.6.1.4.1.18.3.5.5.17.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxCircState |
.1.3.6.1.4.1.18.3.5.5.17.1.3 |
|
The current state of this entry
|
| wfIpxCircIfIndex |
.1.3.6.1.4.1.18.3.5.5.17.1.6 |
|
The identifier of the DP circuit to which this IPX circuit
is linked.
|
| wfIpxCircName |
.1.3.6.1.4.1.18.3.5.5.17.1.7 |
|
The Name of this IPX circuit
|
| wfIpxCircCfgType |
.1.3.6.1.4.1.18.3.5.5.17.1.8 |
|
The type assigned by the user to this IPX circuit.
To enable IPXWAN negotiations on this (WAN) circuit,
set one or more of WAN_RIP, UNNUMBERED_RIP, and
WAN_NLSP.
|
| wfIpxCircLocalMaxPacketSize |
.1.3.6.1.4.1.18.3.5.5.17.1.9 |
|
The maximum size (including header), in bytes that the
media supports on this DP circuit.
|
| wfIpxCircCfgCompressState |
.1.3.6.1.4.1.18.3.5.5.17.1.10 |
|
The configured compression state of this IPX circuit.
|
| wfIpxCircCompressState |
.1.3.6.1.4.1.18.3.5.5.17.1.11 |
|
The actual compression state on this IPX circuit.
|
| wfIpxCircCompressSlots |
.1.3.6.1.4.1.18.3.5.5.17.1.12 |
|
The number of compression slots available on this circuit.
|
| wfIpxCircCompressedSent |
.1.3.6.1.4.1.18.3.5.5.17.1.13 |
|
The number of compressed packets sent.
|
| wfIpxCircCompressedInitSent |
.1.3.6.1.4.1.18.3.5.5.17.1.14 |
|
The number of compression initialization packets sent.
|
| wfIpxCircCompressedRejectsSent |
.1.3.6.1.4.1.18.3.5.5.17.1.15 |
|
The number of compressed packet rejected packets sent.
|
| wfIpxCircUncompressedSent |
.1.3.6.1.4.1.18.3.5.5.17.1.16 |
|
The number of uncompressed packets sent without being compressed
even though compression was turned on for this IPX circuit.
|
| wfIpxCircCompressedReceived |
.1.3.6.1.4.1.18.3.5.5.17.1.17 |
|
The number of compressed packets received.
|
| wfIpxCircCompressedInitReceived |
.1.3.6.1.4.1.18.3.5.5.17.1.18 |
|
The number of compression initialization packets received.
|
| wfIpxCircCompressedRejectsReceived |
.1.3.6.1.4.1.18.3.5.5.17.1.19 |
|
The number of compressed packet rejected packets received.
|
| wfIpxCircUncompressedReceived |
.1.3.6.1.4.1.18.3.5.5.17.1.20 |
|
The number of packets received without having been
compressed even though compression was turned on for
this IPX circuit.
|
| wfIpxCircMediaType |
.1.3.6.1.4.1.18.3.5.5.17.1.21 |
|
The media type used on this IPX circuit.
|
| wfIpxCircCfgNetworkNumber |
.1.3.6.1.4.1.18.3.5.5.17.1.22 |
|
The IPX network number assigned by the user to this
IPX circuit.
|
| wfIpxCircNetworkNumber |
.1.3.6.1.4.1.18.3.5.5.17.1.23 |
|
The IPX network number of this IPX circuit.
|
| wfIpxCircCommonNetworkNumber |
.1.3.6.1.4.1.18.3.5.5.17.1.24 |
|
The IPX common network number assigned to this IPX circuit.
|
| wfIpxCircCfgHostAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.25 |
|
The IPX Host Address assigned by the user to this
IPX circuit.
|
| wfIpxCircHostAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.26 |
|
The IPX Host Address of this IPX circuit.
|
| wfIpxCircMacAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.27 |
|
The IPX Host Address of this IPX circuit.
|
| wfIpxCircCfgBroadcastAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.28 |
|
The Broadcast Address assigned by the user to this
IPX circuit.
|
| wfIpxCircBroadcastAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.29 |
|
The Broadcast Address of this IPX circuit.
|
| wfIpxCircCfgMulticastAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.30 |
|
The Multicast Address assigned by the user to this
IPX circuit.
|
| wfIpxCircMulticastAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.31 |
|
The Multicast Address of this IPX circuit.
|
| wfIpxCircStateChanges |
.1.3.6.1.4.1.18.3.5.5.17.1.32 |
|
The number of times this IPX circuit has changed state.
|
| wfIpxCircInitFails |
.1.3.6.1.4.1.18.3.5.5.17.1.33 |
|
The number of times that initialization of this
circuit has failed.
|
| wfIpxCircDelay |
.1.3.6.1.4.1.18.3.5.5.17.1.34 |
|
The period of time, in microseconds, that it takes to
transmit one byte of data, excluding protocol headers,
to a destination on the other end of this IPX circuit,
if the IPX circuit is free of other traffic. This
value will be filled in by IPX to be either the value
configured or a computed value.
|
| wfIpxCircThroughput |
.1.3.6.1.4.1.18.3.5.5.17.1.35 |
|
The amount of data, in bits per second, that may flow
through this IPX circuit if there is no other traffic.
This value will be filled in by IPX to be either the value
configured or a computed value.
|
| wfIpxCircNeighRouterName |
.1.3.6.1.4.1.18.3.5.5.17.1.36 |
|
The name of the neighboring router on a IPXWAN circuit.
|
| wfIpxCircNeighInternalNetNum |
.1.3.6.1.4.1.18.3.5.5.17.1.37 |
|
The internal network number of the neighboring router
on an IPXWAN circuit.
|
| wfIpxCircCost |
.1.3.6.1.4.1.18.3.5.5.17.1.38 |
|
The cost of this interface, in ticks or hops dependant on
the wfIpxAdvSysRoutingMethod field.
|
| wfIpxCircChecksum |
.1.3.6.1.4.1.18.3.5.5.17.1.39 |
|
Whether or not to check checksums of packets coming into
this IPX circuit.
|
| wfIpxCircCfgEncaps |
.1.3.6.1.4.1.18.3.5.5.17.1.40 |
|
The encapsulation assigned by the user to this
IPX circuit.
|
| wfIpxCircEncaps |
.1.3.6.1.4.1.18.3.5.5.17.1.41 |
|
The encapsulation used on this IPX circuit.
|
| wfIpxCircInTooManyHops |
.1.3.6.1.4.1.18.3.5.5.17.1.42 |
|
The number of IPX packets discarded due to exceeding the
maximum hops count set for this IPX circuit.
|
| wfIpxCircInFiltered |
.1.3.6.1.4.1.18.3.5.5.17.1.43 |
|
The number of incoming IPX packets discarded due to
filtering, not including those counted in
wfIpxTrafficFilterCounter.
|
| wfIpxCircInHdrErrors |
.1.3.6.1.4.1.18.3.5.5.17.1.44 |
|
The number of IPX packets discarded due to errors in
their headers, including any IPX packet with a size less
than the minimum of 30 bytes.
|
| wfIpxCircInUnknownSockets |
.1.3.6.1.4.1.18.3.5.5.17.1.45 |
|
The number of IPX packets discarded because the
destination socket was not known.
|
| wfIpxCircNETBIOSPackets |
.1.3.6.1.4.1.18.3.5.5.17.1.46 |
|
The number of NETBIOS packets received on this
IPX circuit.
|
| wfIpxCircInBadChecksums |
.1.3.6.1.4.1.18.3.5.5.17.1.47 |
|
The number of IPX packets discarded because the
checksum was incorrect.
|
| wfIpxCircInDelivers |
.1.3.6.1.4.1.18.3.5.5.17.1.48 |
|
The number of IPX packets delivered locally
|
| wfIpxCircInDiscards |
.1.3.6.1.4.1.18.3.5.5.17.1.49 |
|
The number of IPX packets received but discarded due to
reasons other than those accounted for by
wfIpxCircInHdrErrors, wfIpxCircInUnknownSockets
|
| wfIpxCircNoRoutes |
.1.3.6.1.4.1.18.3.5.5.17.1.50 |
|
The number of times no route to a destination was
found.
|
| wfIpxCircOutRequests |
.1.3.6.1.4.1.18.3.5.5.17.1.51 |
|
The number of IPX packets supplied locally for
transmission.
|
| wfIpxCircOutMalformedRequests |
.1.3.6.1.4.1.18.3.5.5.17.1.52 |
|
The number of IPX packets supplied locally that contained
errors in their structure.
|
| wfIpxCircOutDiscards |
.1.3.6.1.4.1.18.3.5.5.17.1.53 |
|
The number of outgoing IPX packets discarded due to
reasons other than those accounted for in
|
| wfIpxCircOutFiltered |
.1.3.6.1.4.1.18.3.5.5.17.1.54 |
|
The number of outgoing IPX packets diecarded due to
filtering.
|
| wfIpxCircDestCount |
.1.3.6.1.4.1.18.3.5.5.17.1.55 |
|
The number of networks known to the IPX router
from this IPX circuit.
|
| wfIpxCircServCount |
.1.3.6.1.4.1.18.3.5.5.17.1.56 |
|
The number of services known to the IPX router
from this IPX circuit.
|
| wfIpxCircHostCount |
.1.3.6.1.4.1.18.3.5.5.17.1.57 |
|
The number of hosts known to the IPX router
from this IPX circuit.
|
| wfIpxCircForwardCount |
.1.3.6.1.4.1.18.3.5.5.17.1.58 |
|
The number of forward entries in the IPX router
forwarding table for this IPX circuit.
|
| wfIpxCircTrEndStation |
.1.3.6.1.4.1.18.3.5.5.17.1.59 |
|
Whether or not to do Source Routing, only valid
on token ring media.
|
| wfIpxCircNetbiosAccept |
.1.3.6.1.4.1.18.3.5.5.17.1.60 |
|
Accept NetBios All Networks Broadcast Packets
|
| wfIpxCircNetbiosDeliver |
.1.3.6.1.4.1.18.3.5.5.17.1.61 |
|
Deliver NetBios All Networks Broadcast Packets
|
| wfIpxCircSMDSIndividualAddress |
.1.3.6.1.4.1.18.3.5.5.17.1.62 |
|
The SMDS individual address for this IPX circuit.
|
| wfIpxCircType |
.1.3.6.1.4.1.18.3.5.5.17.1.63 |
|
The type of the circuit. If IPXWAN was enabled on
this circuit, this attribute will indicate the
negotiated routing type.
|
| wfIpxCircWatchdogSpoof |
.1.3.6.1.4.1.18.3.5.5.17.1.64 |
|
Whether or not to do Watchdog Spoofing.
|
| wfIpxCircIPXOutWatchdogSpoofRsps |
.1.3.6.1.4.1.18.3.5.5.17.1.65 |
|
The number of Watchdog response packets sent to
IPX servers in response to Watchdog queries.
|
| wfIpxCircCfgDelay |
.1.3.6.1.4.1.18.3.5.5.17.1.66 |
|
The period of time, in microseconds, that it takes to
transmit one byte of data, excluding protocol headers,
to a destination on the other end of this IPX circuit,
if the IPX circuit is free of other traffic. This
value is assigned by the user.
|
| wfIpxCircCfgThroughput |
.1.3.6.1.4.1.18.3.5.5.17.1.67 |
|
The amount of data, in bits per second, that may flow
through this IPX circuit if there is no other traffic.
This value is assigned by the user.
|
| wfIpxCircSPXOutWatchdogSpoofRsps |
.1.3.6.1.4.1.18.3.5.5.17.1.68 |
|
The number of SPX Watchdog response packets sent to
SPX endpoint in response to Watchdog requests.
|
| wfIpxCircInitStabilizationTimer |
.1.3.6.1.4.1.18.3.5.5.17.1.69 |
|
The circuit RIP/SAP start delay timer to allow routes to stabilize, in seconds
|
| wfIpxCircSVCBroadcast |
.1.3.6.1.4.1.18.3.5.5.17.1.70 |
|
Enable if Frame Relay SVCs should be established for
all adjacent hosts before sending RIP and SAP updates.
|
| wfIpxCircVRRPTriggerState |
.1.3.6.1.4.1.18.3.5.5.17.1.71 |
|
Indicates whether VRRP subsystem wants this IPX Intf to
be enabled or disabled.
|
| wfIpxDestSysInstance |
.1.3.6.1.4.1.18.3.5.5.18.1.1 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxDestNetNum |
.1.3.6.1.4.1.18.3.5.5.18.1.2 |
|
The identifier of this circuit, unique within the
instance. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxDestProtocol |
.1.3.6.1.4.1.18.3.5.5.18.1.3 |
|
The routing protocol from which knowledge of this
destination was obtained.
|
| wfIpxDestTicks |
.1.3.6.1.4.1.18.3.5.5.18.1.4 |
|
The delay in ticks to reach this destination.
|
| wfIpxDestHopCount |
.1.3.6.1.4.1.18.3.5.5.18.1.5 |
|
The number of hops necessary to reach the destination.
|
| wfIpxDestNextHopCircIndex |
.1.3.6.1.4.1.18.3.5.5.18.1.6 |
|
The unique identifier of the IPX circuit used to reach
the next hop.
|
| wfIpxDestNextHopHostAddress |
.1.3.6.1.4.1.18.3.5.5.18.1.7 |
|
The Host address of the Next Hop.
|
| wfIpxDestNextHopNetNum |
.1.3.6.1.4.1.18.3.5.5.18.1.8 |
|
The IPX network number of the next hop.
|
| wfIpxDestAge |
.1.3.6.1.4.1.18.3.5.5.18.1.9 |
|
The current age of this entry, in seconds. Local,
Static, and NLSP destinations are not aged.
|
| wfIpxUserStaticRouteSysInstance |
.1.3.6.1.4.1.18.3.5.5.19.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxUserStaticRouteCircIndex |
.1.3.6.1.4.1.18.3.5.5.19.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxUserStaticRouteNetNum |
.1.3.6.1.4.1.18.3.5.5.19.1.5 |
|
The network number of this static route.
|
| wfIpxUserStaticRouteDelete |
.1.3.6.1.4.1.18.3.5.5.19.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxUserStaticRouteDisable |
.1.3.6.1.4.1.18.3.5.5.19.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxUserStaticRouteTicks |
.1.3.6.1.4.1.18.3.5.5.19.1.6 |
|
The cost in ticks of this static route entry.
|
| wfIpxUserStaticRouteHopCount |
.1.3.6.1.4.1.18.3.5.5.19.1.7 |
|
The hop count to this static route.
|
| wfIpxUserStaticRouteNextHopHostAddress |
.1.3.6.1.4.1.18.3.5.5.19.1.8 |
|
The next hop host address of this entry
|
| wfIpxAutoStaticRouteSysInstance |
.1.3.6.1.4.1.18.3.5.5.20.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxAutoStaticRouteCircIndex |
.1.3.6.1.4.1.18.3.5.5.20.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxAutoStaticRouteNetNum |
.1.3.6.1.4.1.18.3.5.5.20.1.5 |
|
The network number of this static route.
|
| wfIpxAutoStaticRouteDelete |
.1.3.6.1.4.1.18.3.5.5.20.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxAutoStaticRouteDisable |
.1.3.6.1.4.1.18.3.5.5.20.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxAutoStaticRouteTicks |
.1.3.6.1.4.1.18.3.5.5.20.1.6 |
|
The cost in ticks of this static route entry.
|
| wfIpxAutoStaticRouteHopCount |
.1.3.6.1.4.1.18.3.5.5.20.1.7 |
|
The hop count to this static route.
|
| wfIpxAutoStaticRouteNextHopHostAddress |
.1.3.6.1.4.1.18.3.5.5.20.1.8 |
|
The next hop host address of this entry
|
| wfIpxStaticRouteMaskSysInstance |
.1.3.6.1.4.1.18.3.5.5.21.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxStaticRouteMaskCircIndex |
.1.3.6.1.4.1.18.3.5.5.21.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxStaticRouteMaskNetwork |
.1.3.6.1.4.1.18.3.5.5.21.1.5 |
|
The network
|
| wfIpxStaticRouteMaskNetworkMask |
.1.3.6.1.4.1.18.3.5.5.21.1.6 |
|
The network mask.
|
| wfIpxStaticRouteMaskDelete |
.1.3.6.1.4.1.18.3.5.5.21.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxStaticRouteMaskDisable |
.1.3.6.1.4.1.18.3.5.5.21.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxServSysInstance |
.1.3.6.1.4.1.18.3.5.5.22.1.1 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxServType |
.1.3.6.1.4.1.18.3.5.5.22.1.2 |
|
The Service type.
|
| wfIpxServName |
.1.3.6.1.4.1.18.3.5.5.22.1.3 |
|
The Service name.
NOTE: This is a variable length field, 2-47 chars.
|
| wfIpxServProtocol |
.1.3.6.1.4.1.18.3.5.5.22.1.4 |
|
The protocol from which knowledge of service was
obtained.
|
| wfIpxServNetNum |
.1.3.6.1.4.1.18.3.5.5.22.1.5 |
|
The IPX network number portion of the IPX address of the
service.
|
| wfIpxServNode |
.1.3.6.1.4.1.18.3.5.5.22.1.6 |
|
The node portion of the IPX address of the service.
|
| wfIpxServSocket |
.1.3.6.1.4.1.18.3.5.5.22.1.7 |
|
The socket portion of the IPX address of the service.
|
| wfIpxServHopCount |
.1.3.6.1.4.1.18.3.5.5.22.1.8 |
|
The number of hops to the service.
|
| wfIpxServNextHopCircIndex |
.1.3.6.1.4.1.18.3.5.5.22.1.9 |
|
The unique identifier of the IPX circuit used to reach
the next hop.
|
| wfIpxServNextHopHostAddress |
.1.3.6.1.4.1.18.3.5.5.22.1.10 |
|
The Host address of the Next Hop.
|
| wfIpxServNextHopNetNum |
.1.3.6.1.4.1.18.3.5.5.22.1.11 |
|
The IPX network number of the next hop.
|
| wfIpxServAge |
.1.3.6.1.4.1.18.3.5.5.22.1.12 |
|
The current age of this entry, in seconds. Local,
Static, and NLSP services are not aged.
|
| wfIpxUserStaticServSysInstance |
.1.3.6.1.4.1.18.3.5.5.23.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxUserStaticServCircIndex |
.1.3.6.1.4.1.18.3.5.5.23.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxUserStaticServName |
.1.3.6.1.4.1.18.3.5.5.23.1.5 |
|
The service name.
NOTE: This is a variable length field, 2-47 chars.
|
| wfIpxUserStaticServType |
.1.3.6.1.4.1.18.3.5.5.23.1.6 |
|
The service type.
|
| wfIpxUserStaticServDelete |
.1.3.6.1.4.1.18.3.5.5.23.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxUserStaticServDisable |
.1.3.6.1.4.1.18.3.5.5.23.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxUserStaticServNetNum |
.1.3.6.1.4.1.18.3.5.5.23.1.7 |
|
The network number of this static service.
|
| wfIpxUserStaticServHostAddress |
.1.3.6.1.4.1.18.3.5.5.23.1.8 |
|
The host address of this static service.
|
| wfIpxUserStaticServSocket |
.1.3.6.1.4.1.18.3.5.5.23.1.9 |
|
The socket of this static service.
|
| wfIpxUserStaticServHopCount |
.1.3.6.1.4.1.18.3.5.5.23.1.10 |
|
The hop count of this static service.
|
| wfIpxAutoStaticServSysInstance |
.1.3.6.1.4.1.18.3.5.5.24.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxAutoStaticServCircIndex |
.1.3.6.1.4.1.18.3.5.5.24.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxAutoStaticServName |
.1.3.6.1.4.1.18.3.5.5.24.1.5 |
|
The service name.
NOTE: This is a variable length field, 2-47 chars.
|
| wfIpxAutoStaticServType |
.1.3.6.1.4.1.18.3.5.5.24.1.6 |
|
The service type.
|
| wfIpxAutoStaticServDelete |
.1.3.6.1.4.1.18.3.5.5.24.1.1 |
|
Create/Delete parameter. Default is created.
Autos perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxAutoStaticServDisable |
.1.3.6.1.4.1.18.3.5.5.24.1.2 |
|
Enable/Disable parameter. Default is enabled.
Autos perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxAutoStaticServNetNum |
.1.3.6.1.4.1.18.3.5.5.24.1.7 |
|
The network number of this static service.
|
| wfIpxAutoStaticServHostAddress |
.1.3.6.1.4.1.18.3.5.5.24.1.8 |
|
The host address of this static service.
|
| wfIpxAutoStaticServSocket |
.1.3.6.1.4.1.18.3.5.5.24.1.9 |
|
The socket of this static service.
|
| wfIpxAutoStaticServHopCount |
.1.3.6.1.4.1.18.3.5.5.24.1.10 |
|
The hop count of this static service.
|
| wfIpxStaticServMaskSysInstance |
.1.3.6.1.4.1.18.3.5.5.25.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxStaticServMaskCircIndex |
.1.3.6.1.4.1.18.3.5.5.25.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxStaticServMaskNetwork |
.1.3.6.1.4.1.18.3.5.5.25.1.5 |
|
The network
|
| wfIpxStaticServMaskNetworkMask |
.1.3.6.1.4.1.18.3.5.5.25.1.6 |
|
The network mask.
|
| wfIpxStaticServMaskDelete |
.1.3.6.1.4.1.18.3.5.5.25.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxStaticServMaskDisable |
.1.3.6.1.4.1.18.3.5.5.25.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxStaticHostSysInstance |
.1.3.6.1.4.1.18.3.5.5.26.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxStaticHostCircIndex |
.1.3.6.1.4.1.18.3.5.5.26.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxStaticHostAddress |
.1.3.6.1.4.1.18.3.5.5.26.1.5 |
|
The host address of this static host.
|
| wfIpxStaticHostDelete |
.1.3.6.1.4.1.18.3.5.5.26.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxStaticHostDisable |
.1.3.6.1.4.1.18.3.5.5.26.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxStaticHostWanAddress |
.1.3.6.1.4.1.18.3.5.5.26.1.6 |
|
The wan address of this host.
|
| wfIpxStaticHostSubaddress |
.1.3.6.1.4.1.18.3.5.5.26.1.7 |
|
The subaddress used to establish an SVC to the adjacent host.
|
| wfIpxStaticHostTypeOfNumber |
.1.3.6.1.4.1.18.3.5.5.26.1.8 |
|
The type of number used to establish an SVC to the adjacent
host.
|
| wfIpxStaticHostType |
.1.3.6.1.4.1.18.3.5.5.26.1.9 |
|
The type of static host.
|
| wfIpxStaticHostGreConnName |
.1.3.6.1.4.1.18.3.5.5.26.1.10 |
|
The name of the remote GRE connection to which a static host is configured.
|
| wfIpxUserStaticNETBIOSSysInstance |
.1.3.6.1.4.1.18.3.5.5.27.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxUserStaticNETBIOSName |
.1.3.6.1.4.1.18.3.5.5.27.1.4 |
|
The destination name for this NetBIOS static route.
|
| wfIpxUserStaticNETBIOSDelete |
.1.3.6.1.4.1.18.3.5.5.27.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxUserStaticNETBIOSDisable |
.1.3.6.1.4.1.18.3.5.5.27.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxUserStaticNETBIOSDestNetwork |
.1.3.6.1.4.1.18.3.5.5.27.1.5 |
|
The destination network for this NetBIOS static route.
|
| wfIpxAutoStaticNETBIOSSysInstance |
.1.3.6.1.4.1.18.3.5.5.28.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxAutoStaticNETBIOSDestNetwork |
.1.3.6.1.4.1.18.3.5.5.28.1.4 |
|
The destination network for this NetBIOS static route.
|
| wfIpxAutoStaticNETBIOSDelete |
.1.3.6.1.4.1.18.3.5.5.28.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxAutoStaticNETBIOSDisable |
.1.3.6.1.4.1.18.3.5.5.28.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxAutoStaticNETBIOSName |
.1.3.6.1.4.1.18.3.5.5.28.1.5 |
|
The destination name for this NetBIOS static route.
|
| wfIpxRouteFilterSysInstance |
.1.3.6.1.4.1.18.3.5.5.29.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxRouteFilterCircIndex |
.1.3.6.1.4.1.18.3.5.5.29.1.4 |
|
The identifier of this circuit, unique within the
instance of IPX. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxRouteFilterRuleNumber |
.1.3.6.1.4.1.18.3.5.5.29.1.5 |
|
The identifier of the filter, unique within the
IPX circuit.
|
| wfIpxRouteFilterDelete |
.1.3.6.1.4.1.18.3.5.5.29.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxRouteFilterDisable |
.1.3.6.1.4.1.18.3.5.5.29.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxRouteFilterNetwork |
.1.3.6.1.4.1.18.3.5.5.29.1.6 |
|
The network
|
| wfIpxRouteFilterNetworkMask |
.1.3.6.1.4.1.18.3.5.5.29.1.7 |
|
The network mask
|
| wfIpxRouteFilterMode |
.1.3.6.1.4.1.18.3.5.5.29.1.8 |
|
The mode for filtering, Inbound, Outbound, or Both.
|
| wfIpxRouteFilterAction |
.1.3.6.1.4.1.18.3.5.5.29.1.9 |
|
The action for the filter.
|
| wfIpxRouteFilterProtocol |
.1.3.6.1.4.1.18.3.5.5.29.1.10 |
|
Apply this filter only to routes learned on protocol X when
sending RIP updates. Does not apply to Inbound routes. A value
of 1 (default) represents any protocol.
|
| wfIpxRouteFilterCost |
.1.3.6.1.4.1.18.3.5.5.29.1.11 |
|
Cost for routes matching this filter. A Zero cost indicates
that the route's actual cost should be used. Value only used
when action is Advertise.
|
| wfIpxRouteFilterCounter |
.1.3.6.1.4.1.18.3.5.5.29.1.12 |
|
The number of packets matching this filter.
|
| wfIpxRouteFilterPriority |
.1.3.6.1.4.1.18.3.5.5.29.1.13 |
|
Priority of this filter in relation to other filters of the
same type.
|
| wfIpxServNetFilterSysInstance |
.1.3.6.1.4.1.18.3.5.5.30.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxServNetFilterCircIndex |
.1.3.6.1.4.1.18.3.5.5.30.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxServNetFilterRuleNumber |
.1.3.6.1.4.1.18.3.5.5.30.1.5 |
|
The identifier of the filter, unique within the
IPX circuit.
|
| wfIpxServNetFilterDelete |
.1.3.6.1.4.1.18.3.5.5.30.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxServNetFilterDisable |
.1.3.6.1.4.1.18.3.5.5.30.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxServNetFilterNetwork |
.1.3.6.1.4.1.18.3.5.5.30.1.6 |
|
The network.
|
| wfIpxServNetFilterNetworkMask |
.1.3.6.1.4.1.18.3.5.5.30.1.7 |
|
The network mask.
|
| wfIpxServNetFilterType |
.1.3.6.1.4.1.18.3.5.5.30.1.8 |
|
The service type.
|
| wfIpxServNetFilterMode |
.1.3.6.1.4.1.18.3.5.5.30.1.9 |
|
The mode for filtering, Inbound, Outbound, or Both.
|
| wfIpxServNetFilterAction |
.1.3.6.1.4.1.18.3.5.5.30.1.10 |
|
The action for the filter.
|
| wfIpxServNetFilterProtocol |
.1.3.6.1.4.1.18.3.5.5.30.1.11 |
|
Apply this filter only to services learned on protocol X when
sending SAP updates. Does not apply to Inbound services. A value
of 1 (default) represents any protocol.
|
| wfIpxServNetFilterCost |
.1.3.6.1.4.1.18.3.5.5.30.1.12 |
|
Cost for services matching this filter. A Zero cost indicates
that the service's actual cost should be used. Value only used
when action is Advertise.
|
| wfIpxServNetFilterCounter |
.1.3.6.1.4.1.18.3.5.5.30.1.13 |
|
The number of packets matching this filter.
|
| wfIpxServNetFilterPriority |
.1.3.6.1.4.1.18.3.5.5.30.1.14 |
|
Priority of this filter in relation to other filters of the
same type.
|
| wfIpxServNameFilterSysInstance |
.1.3.6.1.4.1.18.3.5.5.31.1.3 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxServNameFilterCircIndex |
.1.3.6.1.4.1.18.3.5.5.31.1.4 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxServNameFilterRuleNumber |
.1.3.6.1.4.1.18.3.5.5.31.1.5 |
|
The identifier of the filter, unique within the
IPX circuit.
|
| wfIpxServNameFilterDelete |
.1.3.6.1.4.1.18.3.5.5.31.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxServNameFilterDisable |
.1.3.6.1.4.1.18.3.5.5.31.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxServNameFilterName |
.1.3.6.1.4.1.18.3.5.5.31.1.6 |
|
The name of the service to be filtered.
NOTE: This is a variable length field, 2-47 chars.
This field may be a regex matching pattern.
|
| wfIpxServNameFilterType |
.1.3.6.1.4.1.18.3.5.5.31.1.7 |
|
The type of the service to be filtered.
|
| wfIpxServNameFilterMode |
.1.3.6.1.4.1.18.3.5.5.31.1.8 |
|
The mode for filtering, Inbound, Outbound, or Both.
|
| wfIpxServNameFilterAction |
.1.3.6.1.4.1.18.3.5.5.31.1.9 |
|
The action for the filter.
|
| wfIpxServNameFilterProtocol |
.1.3.6.1.4.1.18.3.5.5.31.1.10 |
|
Apply this filter only to services learned on protocol X when
sending SAP updates. Does not apply to Inbound services. A value
of 1 (default) represents any protocol.
|
| wfIpxServNameFilterCost |
.1.3.6.1.4.1.18.3.5.5.31.1.11 |
|
Cost for services matching this filter. A Zero cost indicates
that the service's actual cost should be used. Value only used
when action is Advertise.
|
| wfIpxServNameFilterCounter |
.1.3.6.1.4.1.18.3.5.5.31.1.12 |
|
The number of packets matching this filter.
|
| wfIpxServNameFilterPriority |
.1.3.6.1.4.1.18.3.5.5.31.1.13 |
|
Priority of this filter in relation to other filters of the
same type.
|
| wfIpxRipCircSysInstance |
.1.3.6.1.4.1.18.3.5.5.32.1.4 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxRipCircIndex |
.1.3.6.1.4.1.18.3.5.5.32.1.5 |
|
The identifier of this circuit, unique within the
instance of RIP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxRipCircDelete |
.1.3.6.1.4.1.18.3.5.5.32.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxRipCircDisable |
.1.3.6.1.4.1.18.3.5.5.32.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxRipCircState |
.1.3.6.1.4.1.18.3.5.5.32.1.3 |
|
The current state of this entry
|
| wfIpxRipCircMode |
.1.3.6.1.4.1.18.3.5.5.32.1.6 |
|
Whether this RIP entry is in mode.
|
| wfIpxRipCircPace |
.1.3.6.1.4.1.18.3.5.5.32.1.7 |
|
The maximum pace, in packets/second, at which RIP
packets may be sent on this circuit.
|
| wfIpxRipCircUpdate |
.1.3.6.1.4.1.18.3.5.5.32.1.8 |
|
The RIP periodic update interval, in seconds
|
| wfIpxRipCircAgeMultiplier |
.1.3.6.1.4.1.18.3.5.5.32.1.9 |
|
The holding multiplier for information received in
RIP periodic updates.
|
| wfIpxRipCircPacketSize |
.1.3.6.1.4.1.18.3.5.5.32.1.10 |
|
The Maximum RIP packet size used on this circuit
|
| wfIpxRipCircOutPackets |
.1.3.6.1.4.1.18.3.5.5.32.1.11 |
|
The number of locally created RIP packets sent out
this IPX RIP circuit.
|
| wfIpxRipCircInPackets |
.1.3.6.1.4.1.18.3.5.5.32.1.12 |
|
The number of RIP packets received on this IPX circuit,
destined locally.
|
| wfIpxRipCircBadPackets |
.1.3.6.1.4.1.18.3.5.5.32.1.13 |
|
The number of bad RIP packets received on this
IPX circuit.
|
| wfIpxRipCircUseMulticast |
.1.3.6.1.4.1.18.3.5.5.32.1.14 |
|
Use multicast address to send RIP packets.
|
| wfIpxRipCircSplitHorizon |
.1.3.6.1.4.1.18.3.5.5.32.1.15 |
|
Enable/Disable split horizon on this RIP circuit.
|
| wfIpxRipCircGenAutoStaticRoutes |
.1.3.6.1.4.1.18.3.5.5.32.1.16 |
|
Tell IPX to generate entries in the wfIpxAutoStaticRouteTable.
|
| wfIpxRipCircImmedUpdate |
.1.3.6.1.4.1.18.3.5.5.32.1.17 |
|
Enable/Disable parameter. Users perform an
SNMP SET operation on this object in order to
enable/disable RIP immediate update on this
particular circuit. The 'useglobal(3)' means
the value of the global parameter
wfIpxAdvSysGlobalTrigUpdate will be used on the
circuit for this attribute. Default is useglobal.
|
| wfIpxRipCircDefaultRouteSupply |
.1.3.6.1.4.1.18.3.5.5.32.1.18 |
|
Advertise the default route, 0xFFFFFFFE, in RIP packets.
|
| wfIpxRipCircDefaultRouteListen |
.1.3.6.1.4.1.18.3.5.5.32.1.19 |
|
Accept the default route, 0xFFFFFFFE, in RIP packets.
|
| wfIpxSapCircSysInstance |
.1.3.6.1.4.1.18.3.5.5.33.1.4 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxSapCircIndex |
.1.3.6.1.4.1.18.3.5.5.33.1.5 |
|
The identifier of this circuit, unique within the
instance of SAP. This value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxSapCircDelete |
.1.3.6.1.4.1.18.3.5.5.33.1.1 |
|
Create/Delete parameter. Default is created.
Users perform an SNMP SET operation on this
object in order to create/delete this entry.
|
| wfIpxSapCircDisable |
.1.3.6.1.4.1.18.3.5.5.33.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform an SNMP SET operation on this
object in order to enable/disable an entry.
|
| wfIpxSapCircState |
.1.3.6.1.4.1.18.3.5.5.33.1.3 |
|
The current state of this entry
|
| wfIpxSapCircMode |
.1.3.6.1.4.1.18.3.5.5.33.1.6 |
|
Whether this SAP entry is in mode.
|
| wfIpxSapCircPace |
.1.3.6.1.4.1.18.3.5.5.33.1.7 |
|
The maximum pace, in packets/second, at which SAP
packets may be sent on this circuit.
|
| wfIpxSapCircUpdate |
.1.3.6.1.4.1.18.3.5.5.33.1.8 |
|
The SAP periodic update interval, in seconds
|
| wfIpxSapCircAgeMultiplier |
.1.3.6.1.4.1.18.3.5.5.33.1.9 |
|
The holding multiplier for information received in
SAP periodic updates.
|
| wfIpxSapCircPacketSize |
.1.3.6.1.4.1.18.3.5.5.33.1.10 |
|
The Maximum SAP packet size used on this circuit
|
| wfIpxSapCircGetNearestServerReply |
.1.3.6.1.4.1.18.3.5.5.33.1.11 |
|
Enable/Disable responding to GNS requests on this circuit.
|
| wfIpxSapCircNSQAlphabetical |
.1.3.6.1.4.1.18.3.5.5.33.1.12 |
|
Respond to NSQ in Alphabetical order, ie. first-best server.
|
| wfIpxSapCircOutPackets |
.1.3.6.1.4.1.18.3.5.5.33.1.13 |
|
The number of locally created SAP packets sent out
this IPX SAP circuit.
|
| wfIpxSapCircInPackets |
.1.3.6.1.4.1.18.3.5.5.33.1.14 |
|
The number of SAP packets received on this IPX circuit,
destined locally.
|
| wfIpxSapCircBadPackets |
.1.3.6.1.4.1.18.3.5.5.33.1.15 |
|
The number of bad SAP packets received on this
IPX circuit.
|
| wfIpxSapCircUseMulticast |
.1.3.6.1.4.1.18.3.5.5.33.1.16 |
|
Use multicast address to send SAP packets.
|
| wfIpxSapCircSplitHorizon |
.1.3.6.1.4.1.18.3.5.5.33.1.17 |
|
Enable/Disable split horizon on this SAP circuit.
|
| wfIpxSapCircGenAutoStaticServices |
.1.3.6.1.4.1.18.3.5.5.33.1.18 |
|
Tell IPX to generate entries in the wfIpxAutoStaticServTable.
|
| wfIpxSapCircImmedUpdate |
.1.3.6.1.4.1.18.3.5.5.33.1.19 |
|
Enable/Disable parameter. Users perform an
SNMP SET operation on this object in order to
enable/disable RIP immediate update on this
particular circuit. The 'useglobal(3)' means
the value of the global parameter
wfIpxAdvSysGlobalTrigUpdate will be used on the
circuit for this attribute. Default is useglobal.
|
| wfIpxSapCircSaveFullName |
.1.3.6.1.4.1.18.3.5.5.33.1.20 |
|
This allows the Router to ignore all characters following the
NULL character in the service name field of SAP packets. It
is intended to be a memory and cpu saving option.
|
| wfIpxHostSysInstance |
.1.3.6.1.4.1.18.3.5.5.34.1.1 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxHostNextHopCircIndex |
.1.3.6.1.4.1.18.3.5.5.34.1.2 |
|
The unique identifier of the IPX circuit used to reach
the host.
|
| wfIpxHostHostAddress |
.1.3.6.1.4.1.18.3.5.5.34.1.3 |
|
The Host address of the Host.
|
| wfIpxHostNetNum |
.1.3.6.1.4.1.18.3.5.5.34.1.4 |
|
The network number of this host.
|
| wfIpxHostWanAddress |
.1.3.6.1.4.1.18.3.5.5.34.1.5 |
|
The Wan Physical address of this Host.
NOTE: Only valid on WAN media where there is no
one-to-one mapping of host address to physical
address.
|
| wfIpxHostProtocol |
.1.3.6.1.4.1.18.3.5.5.34.1.6 |
|
The routing protocol from which knowledge of this
host was obtained.
|
| wfIpxHostAge |
.1.3.6.1.4.1.18.3.5.5.34.1.7 |
|
The current age of this entry, in seconds. Local and
Static hosts are not aged.
|
| wfIpxForwardSysInstance |
.1.3.6.1.4.1.18.3.5.5.35.1.1 |
|
The unique identifier of the instance of IPX
to which this entry corresponds.
|
| wfIpxForwardCircIndex |
.1.3.6.1.4.1.18.3.5.5.35.1.2 |
|
The unique identifier of the IPX circuit forward table
in which this forward entry resides.
|
| wfIpxForwardNetNum |
.1.3.6.1.4.1.18.3.5.5.35.1.3 |
|
The network number of this forward entry.
|
| wfIpxForwardType |
.1.3.6.1.4.1.18.3.5.5.35.1.4 |
|
The type of this forward entry.
|
| wfIpxForwardProtocol |
.1.3.6.1.4.1.18.3.5.5.35.1.5 |
|
The routing protocol from which knowledge of this
forward was obtained.
|
| wfIpxForwardCount |
.1.3.6.1.4.1.18.3.5.5.35.1.6 |
|
The number of equal cost paths for this forward entry.
|
| wfIpxTrafficFilter2SysInstance |
.1.3.6.1.4.1.18.3.5.5.36.1.7 |
|
The unique identifier for the instance of IPX.
|
| wfIpxTrafficFilter2CircIndex |
.1.3.6.1.4.1.18.3.5.5.36.1.8 |
|
The identifier of this IPX circuit. This
value corresponds to the IPX circuit
identifier found in wfIpxCircIndex.
|
| wfIpxTrafficFilter2RuleNumber |
.1.3.6.1.4.1.18.3.5.5.36.1.9 |
|
ID for the rule.
|
| wfIpxTrafficFilter2Fragment |
.1.3.6.1.4.1.18.3.5.5.36.1.10 |
|
Fragment number - for large rules.
|
| wfIpxTrafficFilter2Create |
.1.3.6.1.4.1.18.3.5.5.36.1.1 |
|
Defines the existence of the traffic filter rule:
created - traffic filter exists
delete - traffic filter does not exist and can be deleted.
|
| wfIpxTrafficFilter2Enable |
.1.3.6.1.4.1.18.3.5.5.36.1.2 |
|
Defines whether or not the traffic filter rule should be used:
enabled - activate the rule.
disabled - inactivate the rule.
|
| wfIpxTrafficFilter2Status |
.1.3.6.1.4.1.18.3.5.5.36.1.3 |
|
Defines the current status of the traffic filter:
inactive - the rule is not in use.
active - the rule is being used.
error - the application detected an error in the rule.
|
| wfIpxTrafficFilter2Counter |
.1.3.6.1.4.1.18.3.5.5.36.1.4 |
|
The number of received packets that have
matched this rule.
|
| wfIpxTrafficFilter2Definition |
.1.3.6.1.4.1.18.3.5.5.36.1.5 |
|
The filter rule definition.
|
| wfIpxTrafficFilter2Reserved |
.1.3.6.1.4.1.18.3.5.5.36.1.6 |
|
Reserved field.
|
| wfIpxTrafficFilter2Name |
.1.3.6.1.4.1.18.3.5.5.36.1.11 |
|
Name of the rule number.
|
