| wfLapbLineNumber |
.1.3.6.1.4.1.18.3.5.1.8.1.4 |
|
Instance identifier, Line Number, filled in by LAPB
|
| wfLapbLLIndex |
.1.3.6.1.4.1.18.3.5.1.8.1.5 |
|
Instance identifier, Lower Layer Index, filled in by LAPB
|
| wfLapbDelete |
.1.3.6.1.4.1.18.3.5.1.8.1.1 |
|
Create/Delete parameter
|
| wfLapbDisable |
.1.3.6.1.4.1.18.3.5.1.8.1.2 |
|
Enable/Disable parameter
|
| wfLapbState |
.1.3.6.1.4.1.18.3.5.1.8.1.3 |
|
Line Driver state variable, Not Present, DSR Wait,
Init, Down, Up
|
| wfLapbCct |
.1.3.6.1.4.1.18.3.5.1.8.1.6 |
|
CCT number for this LAPB subsystem, it is associated with the driver
or application running underneath it.
|
| wfLapbStationType |
.1.3.6.1.4.1.18.3.5.1.8.1.7 |
|
Identifies the desired station type of this interface. A value
of DxE indicates XID enabled but not negotiation has not yet
taken place.
|
| wfLapbControlField |
.1.3.6.1.4.1.18.3.5.1.8.1.8 |
|
This parameter establishes the desired size of the
sequence numbers used to number frames.
|
| wfLapbN1FrameSize |
.1.3.6.1.4.1.18.3.5.1.8.1.9 |
|
The default maximum N1 frame size desired in number of bytes
for a frame transmitted by the DxE. This excludes flags and
0 bits inserted for transparency.
|
| wfLapbKWindowSize |
.1.3.6.1.4.1.18.3.5.1.8.1.10 |
|
The default transmit and receive window size for this Interface.
This is the maximum number of unacknowledged sequence frames that
may be outstanding from this DxE at any one time.
|
| wfLapbN2RxmitCount |
.1.3.6.1.4.1.18.3.5.1.8.1.11 |
|
The default N2 retry count indicates the number of retransmission
attempts which will be tried per frame before a line is determined
to be down. The retry count is max attempts following expiration of
the T1 timer.
|
| wfLapbT1AckTimer |
.1.3.6.1.4.1.18.3.5.1.8.1.12 |
|
The default T1 timer for this interface. This specifies the maximum
time in tenths of seconds to wait for an acknowledgment of a frame.
|
| wfLapbT2AckDelayTimer |
.1.3.6.1.4.1.18.3.5.1.8.1.13 |
|
The default T2 timer for this interface. This specifies the maximum
time in seconds to wait before sending an acknowledgment for a
sequenced frame. A value of one means there will be no delay in
acknowledgment generation.
|
| wfLapbT3DisconnectTimer |
.1.3.6.1.4.1.18.3.5.1.8.1.14 |
|
The T3 timer for this interface. This specifies the time in seconds
to wait before considering the link disconnected. A value of one
indicates the link will be considered disconnected upon completion of
the frame exchange to disconnect the link.
|
| wfLapbT4IdleTimer |
.1.3.6.1.4.1.18.3.5.1.8.1.15 |
|
The T4 timer for this interface. This specifies the maximum time in
seconds to allow without frames being exchanged on the data link.
Not implemented for this project.
|
| wfLapbActionInitiate |
.1.3.6.1.4.1.18.3.5.1.8.1.16 |
|
This identifies the action LAPB will take to initiate link set-up.
|
| wfLapbXidDisable |
.1.3.6.1.4.1.18.3.5.1.8.1.17 |
|
XID enable/disable parameter. This parameter is used to enable
or disable transmission/reception of Test XID frames.
|
| wfLapbCommandAddress |
.1.3.6.1.4.1.18.3.5.1.8.1.18 |
|
The local command address parameter contains the DTE or DCE
value expressed as a single octet.
|
| wfLapbResponseAddress |
.1.3.6.1.4.1.18.3.5.1.8.1.19 |
|
The local response address parameter contains the DTE or DCE
value expressed as a single octet.
|
| wfLapbWanProtocol |
.1.3.6.1.4.1.18.3.5.1.8.1.20 |
|
WAN protocol selection is provided via this parameter. The
supported protocols can be selected per interface.
|
| wfLapbRxOctets |
.1.3.6.1.4.1.18.3.5.1.8.1.21 |
|
Number of octets received without error
|
| wfLapbRxFrames |
.1.3.6.1.4.1.18.3.5.1.8.1.22 |
|
Number of frames received without error
|
| wfLapbTxOctets |
.1.3.6.1.4.1.18.3.5.1.8.1.23 |
|
Number of octets transmitted without error
|
| wfLapbTxFrames |
.1.3.6.1.4.1.18.3.5.1.8.1.24 |
|
Number of frames transmitted without error
|
| wfLapbReXmits |
.1.3.6.1.4.1.18.3.5.1.8.1.25 |
|
Number of retransmission occurances
|
| wfLapbRejectsTx |
.1.3.6.1.4.1.18.3.5.1.8.1.26 |
|
Number of reject frames which were transmitted
|
| wfLapbRejectsRx |
.1.3.6.1.4.1.18.3.5.1.8.1.27 |
|
Number of reject frames which were received
|
| wfLapbFrameRejectsTx |
.1.3.6.1.4.1.18.3.5.1.8.1.28 |
|
Number of Frame Rejects transmitted
|
| wfLapbFrameRejectsRx |
.1.3.6.1.4.1.18.3.5.1.8.1.29 |
|
Number of Frame Rejects received
|
| wfLapbRRsTx |
.1.3.6.1.4.1.18.3.5.1.8.1.30 |
|
Number of Receiver Ready frames transmitted
|
| wfLapbRRsRx |
.1.3.6.1.4.1.18.3.5.1.8.1.31 |
|
Number of Receiver Ready frames received
|
| wfLapbRNRsTx |
.1.3.6.1.4.1.18.3.5.1.8.1.32 |
|
Number of Receiver Not Ready frames transmitted
|
| wfLapbRNRsRx |
.1.3.6.1.4.1.18.3.5.1.8.1.33 |
|
Number of Receiver Not Ready frames received
|
| wfLapbResets |
.1.3.6.1.4.1.18.3.5.1.8.1.34 |
|
Number of Link Connection Resets
|
| wfLapbNormalDisc |
.1.3.6.1.4.1.18.3.5.1.8.1.35 |
|
Number of normal link disconnections
|
| wfLapbAbnormalDisc |
.1.3.6.1.4.1.18.3.5.1.8.1.36 |
|
Number of abnormal link disconnections
|
| wfLapbSetupAllowed |
.1.3.6.1.4.1.18.3.5.1.8.1.37 |
|
Number of successful link connections
|
| wfLapbSetupRefused |
.1.3.6.1.4.1.18.3.5.1.8.1.38 |
|
Number of unsuccessful link connections
|
| wfLapbNetworkType |
.1.3.6.1.4.1.18.3.5.1.8.1.39 |
|
The types GOSIP and NET2 are used in conjunction with the X.25 network
|
| wfLapbIdleRRFrames |
.1.3.6.1.4.1.18.3.5.1.8.1.40 |
|
XID enable/disable parameter. This parameter is used to enable
or disable transmission/reception of Test XID frames.
|
| wfLapbClientType |
.1.3.6.1.4.1.18.3.5.1.8.1.41 |
|
This parameter is used to describe the client above
the LAPB protocol layer. By default, the client is the
X.25 Packet layer. Currently, the only other selection
is ipex or none.
|
| wfLapbRetransmitTimer |
.1.3.6.1.4.1.18.3.5.1.8.1.42 |
|
The Retransmit timer for this interface. This specifies the
maximum time in seconds to allow without retransmitting frames
after RNR and RR received on this interface.
|
