Wellfleet-X25-MIB device MIB details by Wellfleet
Wellfleet-X25-MIB file content
The SNMP protocol is used to for conveying information and commands between agents and managing entities. SNMP uses the User Datagram Protocol (UDP) as the transport protocol for passing data between managers and agents. The reasons for using UDP for SNMP are, firstly it has low overheads in comparison to TCP, which uses a 3-way hand shake for connection. Secondly, in congested networks, SNMP over TCP is a bad idea because TCP in order to maintain reliability will flood the network with retransmissions.
Management information (MIB) is represented as a collection of managed objects. These objects together form a virtual information base called MIB. An agent may implement many MIBs, but all agents must implement a particular MIB called MIB-II [16]. This standard defines variables for things such as interface statistics (interface speeds, MTU, octets sent, octets received, etc.) as well as various other things pertaining to the system itself (system location, system contact, etc.). The main goal of MIB-II is to provide general TCP/IP management information.
Use ActiveXperts Network Monitor 2024 to import vendor-specific MIB files, inclusing Wellfleet-X25-MIB.
| Vendor: | Wellfleet |
|---|---|
| Mib: | Wellfleet-X25-MIB [download] [view objects] |
| Tool: | ActiveXperts Network Monitor 2024 [download] (ships with advanced SNMP/MIB tools) |
Wellfleet-X25-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:50:09 EDT 1995 IMPORTS IpAddress, Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB wfX25Group FROM Wellfleet-COMMON-MIB; wfX25 OBJECT IDENTIFIER ::= { wfX25Group 1 } wfX25Delete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created." DEFVAL { created } ::= { wfX25 1 } wfX25Disable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter. Default is enabled." DEFVAL { enabled } ::= { wfX25 2 } wfX25State OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), notpresent(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the entire X.25." DEFVAL { notpresent } ::= { wfX25 3 } wfX25ServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF WfX25ServiceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table describes the services of a circuit on an X.25 line." ::= { wfX25Group 2 } wfX25ServiceEntry OBJECT-TYPE SYNTAX WfX25ServiceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the X25 Service table." INDEX { wfX25ServiceSlot, wfX25ServiceConnector, wfX25ServiceLineNumber, wfX25ServiceLLIndex, wfX25ServiceCct, wfX25ServiceIndex } ::= { wfX25ServiceTable 1 } WfX25ServiceEntry ::= SEQUENCE { wfX25ServiceDelete INTEGER, wfX25ServiceDisable INTEGER, wfX25ServiceSlot INTEGER, wfX25ServiceConnector INTEGER, wfX25ServiceLineNumber INTEGER, wfX25ServiceLLIndex INTEGER, wfX25ServiceCct INTEGER, wfX25ServiceIndex INTEGER, wfX25ServiceType INTEGER, wfX25ServiceConnRef INTEGER, wfX25ServiceConnId INTEGER, wfX25ServiceRemoteX121Addr DisplayString, wfX25ServiceRemoteIpAddr IpAddress, wfX25ServiceBCast INTEGER, wfX25ServiceMaxConn INTEGER, wfX25ServicePrecedence INTEGER, wfX25ServiceMaxIdle INTEGER, wfX25ServiceCallRetry INTEGER, wfX25ServiceFlowFacility INTEGER, wfX25ServiceWinSize INTEGER, wfX25ServicePktSize INTEGER, wfX25ServiceFastSelRequest INTEGER, wfX25ServiceFastSelAccept INTEGER, wfX25ServiceRevChRequest INTEGER, wfX25ServiceRevChAccept INTEGER, wfX25ServiceCugFormat INTEGER, wfX25ServiceCugType INTEGER, wfX25ServiceCugNum INTEGER, wfX25ServiceUserFacility OCTET STRING, wfX25ServiceValid INTEGER, wfX25ServiceBFE INTEGER, wfX25ServiceForceCugZero INTEGER, wfX25ServiceWcpEnable INTEGER, wfX25ServiceMUX INTEGER, wfX25ServicePtopCallRequest INTEGER, wfX25ServiceVcType INTEGER, wfX25ServicePvcLcn INTEGER, wfX25ServiceMacPoolStart OCTET STRING, wfX25ServiceMacPoolSize INTEGER, wfX25ServiceWindowTimeout INTEGER } wfX25ServiceDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter, default = created." DEFVAL { created } ::= { wfX25ServiceEntry 1 } wfX25ServiceDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter, default = enabled." DEFVAL { enabled } ::= { wfX25ServiceEntry 2 } wfX25ServiceSlot OBJECT-TYPE SYNTAX INTEGER(1..14) ACCESS read-only STATUS mandatory DESCRIPTION "Slot number and part of Instance Id." ::= { wfX25ServiceEntry 3 } wfX25ServiceConnector OBJECT-TYPE SYNTAX INTEGER { one(1), two(2), three(3), four(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Connector number and instance ID member." ::= { wfX25ServiceEntry 4 } wfX25ServiceLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the line number assigned to the driver X.25 is running over. No used in 7.60." ::= { wfX25ServiceEntry 5 } wfX25ServiceLLIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60." ::= { wfX25ServiceEntry 6 } wfX25ServiceCct OBJECT-TYPE SYNTAX INTEGER(1..1024) ACCESS read-only STATUS mandatory DESCRIPTION "Circuit number and instance ID member." ::= { wfX25ServiceEntry 7 } wfX25ServiceIndex OBJECT-TYPE SYNTAX INTEGER(1..4000) ACCESS read-only STATUS mandatory DESCRIPTION "X.25 service entry record ID for this instance." ::= { wfX25ServiceEntry 8 } wfX25ServiceType OBJECT-TYPE SYNTAX INTEGER { pdntype(1), ddntype(2), ptoptype(4), npttype(8), ipextype(16), qllctype(32) } ACCESS read-write STATUS mandatory DESCRIPTION "Type of Service." ::= { wfX25ServiceEntry 9 } wfX25ServiceConnRef OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Use of Connection Reference Numbers in Call Request For PDN only, if ON then use wfX25ServiceConnId as starting reference number for PDN." DEFVAL { off } ::= { wfX25ServiceEntry 10 } wfX25ServiceConnId OBJECT-TYPE SYNTAX INTEGER(1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Connection Id to be used in a PTOP Call request. For PDN this will be the starting number to be used as Connection Id in PDN." DEFVAL { 1 } ::= { wfX25ServiceEntry 11 } wfX25ServiceRemoteX121Addr OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Remote X.121 address for this table entry instance." ::= { wfX25ServiceEntry 12 } wfX25ServiceRemoteIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Remote IP address for PDN and DDN only." ::= { wfX25ServiceEntry 13 } wfX25ServiceBCast OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Broadcast recipient status for this table entry instance." DEFVAL { off } ::= { wfX25ServiceEntry 14 } wfX25ServiceMaxConn OBJECT-TYPE SYNTAX INTEGER(1..4) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum connections per destination for this table entry instance." DEFVAL { 2 } ::= { wfX25ServiceEntry 15 } wfX25ServicePrecedence OBJECT-TYPE SYNTAX INTEGER { negot(1), default(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Precedence value for this table entry instance. DDN only." DEFVAL { default } ::= { wfX25ServiceEntry 16 } wfX25ServiceMaxIdle OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Idle Time in Minutes for this table entry instance. If 0 is entered the connection stays on forever." DEFVAL { 2 } ::= { wfX25ServiceEntry 17 } wfX25ServiceCallRetry OBJECT-TYPE SYNTAX INTEGER(10..999) ACCESS read-write STATUS mandatory DESCRIPTION "Interval in seconds between Call Request to same the destination. Must be at least 2 times T11/T21 Timer for Packet Level." DEFVAL { 60 } ::= { wfX25ServiceEntry 18 } wfX25ServiceFlowFacility OBJECT-TYPE SYNTAX INTEGER { negot(1), default(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Flow Control negotiation facility parameter for this instance." DEFVAL { default } ::= { wfX25ServiceEntry 19 } wfX25ServiceWinSize OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Packet window size parameter for this table entry instance." DEFVAL { 2 } ::= { wfX25ServiceEntry 20 } wfX25ServicePktSize OBJECT-TYPE SYNTAX INTEGER { size16(4), size32(5), size64(6), size128(7), size256(8), size512(9), size1024(10), size2048(11), size4096(12) } ACCESS read-write STATUS mandatory DESCRIPTION "Packet size parameter for this table entry instance." DEFVAL { size128 } ::= { wfX25ServiceEntry 21 } wfX25ServiceFastSelRequest OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Fast Select Request Facility for this table entry instance." DEFVAL { off } ::= { wfX25ServiceEntry 22 } wfX25ServiceFastSelAccept OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Fast Select Accept Facility for this table entry instance." DEFVAL { off } ::= { wfX25ServiceEntry 23 } wfX25ServiceRevChRequest OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Reverse Charge Request Facility for this table entry instance." DEFVAL { off } ::= { wfX25ServiceEntry 24 } wfX25ServiceRevChAccept OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Reverse charge Accept Facility for this table entry instance." DEFVAL { off } ::= { wfX25ServiceEntry 25 } wfX25ServiceCugFormat OBJECT-TYPE SYNTAX INTEGER { none(1), basic(2), ext(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Closed User Group Facility Format." DEFVAL { none } ::= { wfX25ServiceEntry 26 } wfX25ServiceCugType OBJECT-TYPE SYNTAX INTEGER { normal(1), oa(2), bilat(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Closed User Group Facility Type: Normal CUG, Bilateral CUG, or Outgoing Access CUG." DEFVAL { normal } ::= { wfX25ServiceEntry 27 } wfX25ServiceCugNum OBJECT-TYPE SYNTAX INTEGER(1..9999) ACCESS read-write STATUS mandatory DESCRIPTION "Closed User Group (CUG) number." ::= { wfX25ServiceEntry 28 } wfX25ServiceUserFacility OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Additional User Supplied Facilities. Must be in Hexadecimal form." ::= { wfX25ServiceEntry 29 } wfX25ServiceValid OBJECT-TYPE SYNTAX INTEGER { valid(1), invalid(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Validity of the record - updated by X.25." DEFVAL { valid } ::= { wfX25ServiceEntry 30 } wfX25ServiceBFE OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enabled if DDNX.25/BFE enabled." DEFVAL { disabled } ::= { wfX25ServiceEntry 31 } wfX25ServiceForceCugZero OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Force Closed User Group of Zero." DEFVAL { disabled } ::= { wfX25ServiceEntry 32 } wfX25ServiceWcpEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable compression" DEFVAL { disabled } ::= { wfX25ServiceEntry 33 } wfX25ServiceMUX OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set to Enabled to perform 1356 Multiplexing of protocols in the same Vc" DEFVAL { disabled } ::= { wfX25ServiceEntry 34 } wfX25ServicePtopCallRequest OBJECT-TYPE SYNTAX INTEGER { default(1), local(2), remote(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Select which side of PTOP circuit initiates the connection. (default = highest X.121 address initiates the call)" DEFVAL { default } ::= { wfX25ServiceEntry 35 } wfX25ServiceVcType OBJECT-TYPE SYNTAX INTEGER { svc(1), pvc(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines whether this service record represents a Switch Virtual Circuit (SVC) or Permanent Virtual Circuit (PVC). (default = svc)" DEFVAL { svc } ::= { wfX25ServiceEntry 36 } wfX25ServicePvcLcn OBJECT-TYPE SYNTAX INTEGER (0..4095) ACCESS read-write STATUS mandatory DESCRIPTION "PVC Logical Channel Number for this service record" DEFVAL { 1 } ::= { wfX25ServiceEntry 37 } wfX25ServiceMacPoolStart OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-write STATUS mandatory DESCRIPTION "Starting address of MAC address pool" ::= { wfX25ServiceEntry 38 } wfX25ServiceMacPoolSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The size of MAC address pool" ::= { wfX25ServiceEntry 39 } wfX25ServiceWindowTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Window Timeout to detect a dysfunctional VC." DEFVAL { 0 } ::= { wfX25ServiceEntry 40 } wfX25VcTable OBJECT-TYPE SYNTAX SEQUENCE OF WfX25VcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This is a table of Statistic Entries is per Virtual Circuit." ::= { wfX25Group 4 } wfX25VcEntry OBJECT-TYPE SYNTAX WfX25VcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the X.25 VC table." INDEX { wfX25VcSlotNum, wfX25VcConnector, wfX25VcLineNumber, wfX25VcLLIndex, wfX25VcCct, wfX25VcNumber } ::= { wfX25VcTable 1 } WfX25VcEntry ::= SEQUENCE { wfX25VcSlotNum INTEGER, wfX25VcConnector INTEGER, wfX25VcLineNumber INTEGER, wfX25VcLLIndex INTEGER, wfX25VcCct INTEGER, wfX25VcNumber INTEGER, wfX25VcDataTxs Counter, wfX25VcInterruptTxs Counter, wfX25VcResetTxs Counter, wfX25VcRrTxs Counter, wfX25VcRnrTxs Counter, wfX25VcRejectTxs Counter, wfX25VcSegmentTxs Counter, wfX25VcBytesTxs Counter, wfX25VcIntBytesTxs Counter, wfX25VcDataRxs Counter, wfX25VcInterruptRxs Counter, wfX25VcResetRxs Counter, wfX25VcRrRxs Counter, wfX25VcRnrRxs Counter, wfX25VcRejectRxs Counter, wfX25VcSegmentRxs Counter, wfX25VcBytesRxs Counter, wfX25VcIntBytesRxs Counter, wfX25VcApPktsDropped Counter, wfX25VcRemoteX121Addr DisplayString } wfX25VcSlotNum OBJECT-TYPE SYNTAX INTEGER(1..14) ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID and Slot number this VC is on." ::= { wfX25VcEntry 1 } wfX25VcConnector OBJECT-TYPE SYNTAX INTEGER { one(1), two(2), three(3), four(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID and Connector number this VC is using" ::= { wfX25VcEntry 2 } wfX25VcLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the line number assigned to the driver X25 is running on top of and this VC is running on. No used in 7.60" ::= { wfX25VcEntry 3 } wfX25VcLLIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60." ::= { wfX25VcEntry 4 } wfX25VcCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID and CCT supporting these VCs. User determines this CCT via log." ::= { wfX25VcEntry 5 } wfX25VcNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID and VC number for this VC. This number corresponds to the LCN." ::= { wfX25VcEntry 6 } wfX25VcDataTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Packets sent." ::= { wfX25VcEntry 7 } wfX25VcInterruptTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Packets sent." ::= { wfX25VcEntry 8 } wfX25VcResetTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reset Packets sent." ::= { wfX25VcEntry 9 } wfX25VcRrTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Ready Packets sent." ::= { wfX25VcEntry 10 } wfX25VcRnrTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Not Ready Packets sent." ::= { wfX25VcEntry 11 } wfX25VcRejectTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reject Packets sent." ::= { wfX25VcEntry 12 } wfX25VcSegmentTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Charge Units sent." ::= { wfX25VcEntry 13 } wfX25VcBytesTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Bytes sent." ::= { wfX25VcEntry 14 } wfX25VcIntBytesTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Data Bytes sent." ::= { wfX25VcEntry 15 } wfX25VcDataRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Packets received." ::= { wfX25VcEntry 16 } wfX25VcInterruptRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Packets received." ::= { wfX25VcEntry 17 } wfX25VcResetRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reset Packets received." ::= { wfX25VcEntry 18 } wfX25VcRrRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Ready Packets received." ::= { wfX25VcEntry 19 } wfX25VcRnrRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Not Ready Packets received." ::= { wfX25VcEntry 20 } wfX25VcRejectRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reject Packets received." ::= { wfX25VcEntry 21 } wfX25VcSegmentRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Charge Units received." ::= { wfX25VcEntry 22 } wfX25VcBytesRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Bytes received." ::= { wfX25VcEntry 23 } wfX25VcIntBytesRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Data Bytes received." ::= { wfX25VcEntry 24 } wfX25VcApPktsDropped OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Application/redirector Packets Droped" ::= { wfX25VcEntry 25 } wfX25VcRemoteX121Addr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Remote DTE Address for this connection" ::= { wfX25VcEntry 26 } wfLapbPktTable OBJECT-TYPE SYNTAX SEQUENCE OF WfLapbPktEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of LAPB PKT Level Parameters" ::= { wfX25Group 5 } wfLapbPktEntry OBJECT-TYPE SYNTAX WfLapbPktEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the LAPB PKT table" INDEX { wfLapbPktSlotNum, wfLapbPktConnector, wfLapbPktLineNumber, wfLapbPktLLIndex } ::= { wfLapbPktTable 1 } WfLapbPktEntry ::= SEQUENCE { wfLapbPktDelete INTEGER, wfLapbPktDisable INTEGER, wfLapbPktSlotNum INTEGER, wfLapbPktConnector INTEGER, wfLapbPktLineNumber INTEGER, wfLapbPktLLIndex INTEGER, wfLapbPktLapbCct INTEGER, wfLapbPktLinkId INTEGER, wfLapbPktLineState INTEGER, wfLapbPktSeqSize INTEGER, wfLapbPktMaxWindow INTEGER, wfLapbPktMaxLength INTEGER, wfLapbPktMaxThroughput INTEGER, wfLapbPktFlowCtl INTEGER, wfLapbPktThroughput INTEGER, wfLapbPktUserIdentity INTEGER, wfLapbPktInCalls INTEGER, wfLapbPktOutCalls INTEGER, wfLapbPktFastAccept INTEGER, wfLapbPktReverseAccept INTEGER, wfLapbPktFastSelect INTEGER, wfLapbPktReverseCharging INTEGER, wfLapbPktCugSelection INTEGER, wfLapbPktCugOA INTEGER, wfLapbPktCugBilateral INTEGER, wfLapbPktRpoaSelection INTEGER, wfLapbPktChargeInform INTEGER, wfLapbPktTransitDelay INTEGER, wfLapbPktFullAddressing INTEGER, wfLapbPktAccFormat INTEGER, wfLapbPktRelFormat INTEGER, wfLapbPktT1 INTEGER, wfLapbPktT2 INTEGER, wfLapbPktT3 INTEGER, wfLapbPktT4 INTEGER, wfLapbPktIwcCnt INTEGER, wfLapbPktIwcId INTEGER, wfLapbPktBwcCnt INTEGER, wfLapbPktBwcId INTEGER, wfLapbPktOwcCnt INTEGER, wfLapbPktOwcId INTEGER, wfLapbPktDefWindow INTEGER, wfLapbPktDefLength INTEGER, wfLapbPktDefClass INTEGER, wfLapbPktDxe INTEGER, wfLapbPktConformance INTEGER, wfLapbPktStandard INTEGER, wfLapbPktNetaddr DisplayString, wfLapbPktStatistics INTEGER, wfLapbPktNetaddrType INTEGER, wfLapbPktDDNIpAddr IpAddress, wfLapbPktPDNX121Addr DisplayString, wfLapbPktTxT5 INTEGER, wfLapbPktUseDfltService INTEGER, wfLapbPktPVCCnt INTEGER, wfLapbPktPVCLowLcn INTEGER, wfLapbPktClientTimer INTEGER, wfLapbPktPduSize INTEGER, wfLapbPktTranspacCauseCodeEnable INTEGER } wfLapbPktDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created." DEFVAL { created } ::= { wfLapbPktEntry 1 } wfLapbPktDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter" DEFVAL { enabled } ::= { wfLapbPktEntry 2 } wfLapbPktSlotNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier. This is the slot number where this X.25 packet layer is running." ::= { wfLapbPktEntry 3 } wfLapbPktConnector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier. This is the Physical connector number for the Physical layer associated with this X25 Packet layer." ::= { wfLapbPktEntry 4 } wfLapbPktLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier. This is the line number assigned to the LAPB Driver associated with this X25 Packet Layer. Not used in 7.60" ::= { wfLapbPktEntry 5 } wfLapbPktLLIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60." ::= { wfLapbPktEntry 6 } wfLapbPktLapbCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Circuit number of Lapb (SYNC) driver associated with this X25 Packet Layer" ::= { wfLapbPktEntry 7 } wfLapbPktLinkId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Access Link identifier - index into line information array." ::= { wfLapbPktEntry 8 } wfLapbPktLineState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), notpresent(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Reflects the state of the X.25 packet layer that is associated with this network record. When the state of this parameter is set to Up, the router can transfer data between the line layer and the packet layer. Note that this parameter is used internally; it does NOT reflect the status of the underlying synchronous circuit." DEFVAL { notpresent } ::= { wfLapbPktEntry 9 } wfLapbPktSeqSize OBJECT-TYPE SYNTAX INTEGER { mod8(8), mod128(128) } ACCESS read-write STATUS mandatory DESCRIPTION "Sequence numbering scheme for the data packets. Modulo 8 or Modulo 128" DEFVAL { mod8 } ::= { wfLapbPktEntry 10 } wfLapbPktMaxWindow OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum window size that can be negotiated on a per call basis, if the flow control facility is subscribed too. Extended window size of 127 can be used if wfLapbPktSeqSize is 128. Otherwise the maximum is 7. This attribute is effective only if the attribute wfLapbPktFloCtl is set to 'ON'." DEFVAL { 2 } ::= { wfLapbPktEntry 11 } wfLapbPktMaxLength OBJECT-TYPE SYNTAX INTEGER { size16(4), size32(5), size64(6), size128(7), size256(8), size512(9), size1024(10), size2048(11), size4096(12) } ACCESS read-write STATUS mandatory DESCRIPTION "Maximum packet length that can be negotiated on a per call basis, if the flow control facility is subscribed too. This attribute is effective only if the attribute wfLapbPktFloCtl is set to 'ON'. This attribute should not be greater than the wfSYNCEntry attribute wfSyncMtu." DEFVAL { size128 } ::= { wfLapbPktEntry 12 } wfLapbPktMaxThroughput OBJECT-TYPE SYNTAX INTEGER { thrclass75(3), thrclass150(4), thrclass300(5), thrclass600(6), thrclass1200(7), thrclass2400(8), thrclass4800(9), thrclass9600(10), thrclass19200(11), thrclass48k(12), thrclass64k(13) } ACCESS read-write STATUS mandatory DESCRIPTION "Maximum throughput class value that can be negotiated on a per call basis, if the throughput class negotiation facility is subscribed too. For this to be effective the attribute wfLapbPktThroughput must be set to ON." DEFVAL { thrclass19200 } ::= { wfLapbPktEntry 13 } wfLapbPktFlowCtl OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Flow control parameter negotiation facility subscription" DEFVAL { off } ::= { wfLapbPktEntry 14 } wfLapbPktThroughput OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Throughput class negotiation facility subscription" DEFVAL { off } ::= { wfLapbPktEntry 15 } wfLapbPktUserIdentity OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Network user identification (NUI) related facility subscription" DEFVAL { off } ::= { wfLapbPktEntry 16 } wfLapbPktInCalls OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) incoming calls are permitted" DEFVAL { on } ::= { wfLapbPktEntry 17 } wfLapbPktOutCalls OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) outgoing calls are permitted" DEFVAL { on } ::= { wfLapbPktEntry 18 } wfLapbPktFastAccept OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) fast select acceptance facility is subscribed too." DEFVAL { off } ::= { wfLapbPktEntry 19 } wfLapbPktReverseAccept OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) reverse charge aceptance facility is subscribed to. If this is set this packet layer will simply accept calls with reverse charge facility. But the packet layer (router) will not provide any charging information." DEFVAL { off } ::= { wfLapbPktEntry 20 } wfLapbPktFastSelect OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) fast select facility is allowed on a per call basis." DEFVAL { off } ::= { wfLapbPktEntry 21 } wfLapbPktReverseCharging OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not (ON/OFF) reverse charging facility is allowed on a per call basis." DEFVAL { off } ::= { wfLapbPktEntry 22 } wfLapbPktCugSelection OBJECT-TYPE SYNTAX INTEGER { off(2), basic(16), extended(32) } ACCESS read-write STATUS mandatory DESCRIPTION "Format of the Closed User Group (CUG) related facilities supported." DEFVAL { off } ::= { wfLapbPktEntry 23 } wfLapbPktCugOA OBJECT-TYPE SYNTAX INTEGER { off(2), cugoa(64) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not CUG with Outgoing access selection facility is supported." DEFVAL { off } ::= { wfLapbPktEntry 24 } wfLapbPktCugBilateral OBJECT-TYPE SYNTAX INTEGER { off(2), bilat(128) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not Bilateral Closed User Group related facility is supported. If this is set, then the wfLapbPktCugSelection should be set to EXTENDED." DEFVAL { off } ::= { wfLapbPktEntry 25 } wfLapbPktRpoaSelection OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not RPOA related facility is supported. Outgoing calls will not contain any RPOA facility. But if set this packet layer will simply accept calls with RPOA related facility." DEFVAL { off } ::= { wfLapbPktEntry 26 } wfLapbPktChargeInform OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether or not the charging information related facilities are supported. Outgoing calls will not contain the charge information related facility. But if set this packet layer will simply accept calls with the charge information related facility. No charging information will be collected." DEFVAL { off } ::= { wfLapbPktEntry 27 } wfLapbPktTransitDelay OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Transit delay indication facility. If set, accept calls with this facility." DEFVAL { off } ::= { wfLapbPktEntry 28 } wfLapbPktFullAddressing OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If this attribute is set, the full local X121 address (calling address) is supplied in the outgoing call request and the X.25 network also expected to provide the full called address in the incoming call packet." DEFVAL { on } ::= { wfLapbPktEntry 29 } wfLapbPktAccFormat OBJECT-TYPE SYNTAX INTEGER { basic(2), allext(255), defbas(103) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the format of the call accepted packet." DEFVAL { basic } ::= { wfLapbPktEntry 30 } wfLapbPktRelFormat OBJECT-TYPE SYNTAX INTEGER { basic(2), allext(255), defext(103) } ACCESS read-write STATUS mandatory DESCRIPTION "Connection release format - format of Clear Requests" DEFVAL { basic } ::= { wfLapbPktEntry 31 } wfLapbPktT1 OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-write STATUS mandatory DESCRIPTION "Local confirmation timeouts in seconds. This timer represents the following CCITT timers. If DCE: T10 (restart), T12 (reset), T13 (clear) If DTE: T20 (restart), T22 (reset), T23 (clear)" DEFVAL { 60 } ::= { wfLapbPktEntry 32 } wfLapbPktT2 OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-write STATUS mandatory DESCRIPTION "Call confirmation time out in seconds. This represent the CCITT T11 timer for the DCE and T21 timer for the DTE." DEFVAL { 180 } ::= { wfLapbPktEntry 33 } wfLapbPktT3 OBJECT-TYPE SYNTAX INTEGER(200..2000) ACCESS read-write STATUS mandatory DESCRIPTION "Congestion or busy condition watchdog timer in milliseconds. When system resources needed for packet assembly/deassembly depleted, this timer is set to reenter the PLP state machine to retry. User should use extreme caution in manipulating this timer." DEFVAL { 200 } ::= { wfLapbPktEntry 34 } wfLapbPktT4 OBJECT-TYPE SYNTAX INTEGER(200..2000) ACCESS read-write STATUS mandatory DESCRIPTION "Data packet transmission watchdog timer in milliseconds. This is the delay for acknowledgement. It is used to reenter PLP state machine also. User should use extreme caution in manipulating this timer." DEFVAL { 200 } ::= { wfLapbPktEntry 35 } wfLapbPktIwcCnt OBJECT-TYPE SYNTAX INTEGER(1..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of IWC (Incoming VC's) defined on this access link." ::= { wfLapbPktEntry 36 } wfLapbPktIwcId OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-write STATUS mandatory DESCRIPTION "Low LCN ID for IWC (Incoming VC's) defined on this access link." DEFVAL { 1 } ::= { wfLapbPktEntry 37 } wfLapbPktBwcCnt OBJECT-TYPE SYNTAX INTEGER(1..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of BWC (Bidirectional VC's) defined on this access link." ::= { wfLapbPktEntry 38 } wfLapbPktBwcId OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-write STATUS mandatory DESCRIPTION "Low LCN ID for BWC (Bidirectional VC's) defined on this access link." DEFVAL { 1 } ::= { wfLapbPktEntry 39 } wfLapbPktOwcCnt OBJECT-TYPE SYNTAX INTEGER(1..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of OWC (Outgoing VC's) defined on this access link." ::= { wfLapbPktEntry 40 } wfLapbPktOwcId OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-write STATUS mandatory DESCRIPTION "Low LCN ID for OWC (Outgoing VC's) defined on this access link." DEFVAL { 1 } ::= { wfLapbPktEntry 41 } wfLapbPktDefWindow OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "Non standard default transmit/receive window size." DEFVAL { 2 } ::= { wfLapbPktEntry 42 } wfLapbPktDefLength OBJECT-TYPE SYNTAX INTEGER { size16(4), size32(5), size64(6), size128(7), size256(8), size512(9), size1024(10), size2048(11), size4096(12) } ACCESS read-write STATUS mandatory DESCRIPTION "Non standard default transmit/receive packet size. This attribute should not be greater than the wfSyncEntry attribute wfSyncMtu." DEFVAL { size128 } ::= { wfLapbPktEntry 43 } wfLapbPktDefClass OBJECT-TYPE SYNTAX INTEGER(3..13) ACCESS read-write STATUS mandatory DESCRIPTION "Non standard default transmit/receive throughput class assignment." DEFVAL { 11 } ::= { wfLapbPktEntry 44 } wfLapbPktDxe OBJECT-TYPE SYNTAX INTEGER { x25dtersta(1), x25dte(2), x25dce(3), x25dtedxe(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specify type of local X25 interface and imply subsequent rules of X.25. DXE_X25DTERSTA ->DTE mode with Restart Procedure. DXE_X25DTE ->DTE mode without any restart procedure DXE_X25DCE ->DCE mode with restart procedure DXE_X25DTEDXE ->DTE/DTE environment, unassigned roles." DEFVAL { x25dtersta } ::= { wfLapbPktEntry 45 } wfLapbPktConformance OBJECT-TYPE SYNTAX INTEGER { dxe1980(257), fsel1980(258), dxe1984(513), fsel1984(514), dxe1988(1025), fsel1988(1026) } ACCESS read-write STATUS mandatory DESCRIPTION "CCITT conformance recommendation used on each line." DEFVAL { dxe1988 } ::= { wfLapbPktEntry 46 } wfLapbPktStandard OBJECT-TYPE SYNTAX INTEGER { stdiso(16), stddod(32), stdnone(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Network Standard to be used on each line." DEFVAL { stdnone } ::= { wfLapbPktEntry 47 } wfLapbPktNetaddr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This Link's Network address (X121 address)." ::= { wfLapbPktEntry 48 } wfLapbPktStatistics OBJECT-TYPE SYNTAX INTEGER { statson(1), statsoff(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Gives the user the ability to Turn ON or Shut OFF statistics computation. This can be shut off for better performance on the line. Now it also provides a small packet trace function." DEFVAL { statsoff } ::= { wfLapbPktEntry 49 } wfLapbPktNetaddrType OBJECT-TYPE SYNTAX INTEGER { pdntype(1), ddntype(2), bfetype(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This defines whether the Network connection is to a DDN network or PDN Network. This is used to decide how the Local X121 Network address is derived. If this attribute is set to DDN the Local X121 address used in the attribute wfLapbPktNetaddr will be derived from the user supplied IP address. Otherwise the X121 address should be supplid by the user." DEFVAL { pdntype } ::= { wfLapbPktEntry 50 } wfLapbPktDDNIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "If the wfLapbPktNetaddrType is DDNTYPE or DDN_BFE this is the user supplied local IP address. The router will convert this to the corresponding X121 address and the X121 address value will be put in wfLapbPktNetaddr attribute." ::= { wfLapbPktEntry 51 } wfLapbPktPDNX121Addr OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "If the wfLapbPktNetaddrType is PDNTYPE this is the user supplied local X.121 address. The router will put this value in wfLapbPktNetaddr attribute." ::= { wfLapbPktEntry 52 } wfLapbPktTxT5 OBJECT-TYPE SYNTAX INTEGER(1..8000) ACCESS read-write STATUS mandatory DESCRIPTION "Tx window size transmit delay timer" DEFVAL { 200 } ::= { wfLapbPktEntry 53 } wfLapbPktUseDfltService OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether or not to use the default ddn service." DEFVAL { off } ::= { wfLapbPktEntry 54 } wfLapbPktPVCCnt OBJECT-TYPE SYNTAX INTEGER(1..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of PVCs defined on this access link." ::= { wfLapbPktEntry 55 } wfLapbPktPVCLowLcn OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-write STATUS mandatory DESCRIPTION "Low LCN ID for PVCs defined on this access link." DEFVAL { 1 } ::= { wfLapbPktEntry 56 } wfLapbPktClientTimer OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-write STATUS mandatory DESCRIPTION "Client application response timeout period in seconds. This timer allows for the extended delays that can occur negotiating with remote clients (e.g., IPEX or QLLC). This timer must be greater than the wfLapbPktT3 period and less than wfLapbPktT2." DEFVAL { 120 } ::= { wfLapbPktEntry 57 } wfLapbPktPduSize OBJECT-TYPE SYNTAX INTEGER (1600..4096) ACCESS read-write STATUS mandatory DESCRIPTION "The X.25 PDU Size for this logical channel. This PDU size represents the M_BUF_SIZE used for X.25 Fragmentation and Reassembly in the packet layer. This is the largest message size X.25 will handle from a client on a given Logical Channel. Changing this attribute enables X.25 to handle client messages up to 4096 bytes in length" DEFVAL { 1600 } ::= { wfLapbPktEntry 58 } wfLapbPktTranspacCauseCodeEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Use Transpac Cause Codes , default = disabled." DEFVAL { disabled } ::= { wfLapbPktEntry 59 } wfLapbPktStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WfLapbPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of LAPB PKT Level Statistics." ::= { wfX25Group 6 } wfLapbPktStatsEntry OBJECT-TYPE SYNTAX WfLapbPktStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Packet level statistics." INDEX { wfLapbPktStatsSlotNum, wfLapbPktStatsConnector, wfLapbPktStatsLineNumber, wfLapbPktStatsLLIndex } ::= { wfLapbPktStatsTable 1 } WfLapbPktStatsEntry ::= SEQUENCE { wfLapbPktStatsSlotNum INTEGER, wfLapbPktStatsConnector INTEGER, wfLapbPktStatsLineNumber INTEGER, wfLapbPktStatsLLIndex INTEGER, wfLapbPktStatsCct INTEGER, wfLapbPktStatsLineAddress DisplayString, wfLapbPktStatsMaxVcs Counter, wfLapbPktStatsActiveVcs Counter, wfLapbPktStatsActiveMax Counter, wfLapbPktStatsTotalConnections Counter, wfLapbPktStatsFailedConnections Counter, wfLapbPktStatsNormalDisconnects Counter, wfLapbPktStatsAbnormalDisconnects Counter, wfLapbPktStatsDataTxs Counter, wfLapbPktStatsInterruptTxs Counter, wfLapbPktStatsResetTxs Counter, wfLapbPktStatsRrTxs Counter, wfLapbPktStatsRnrTxs Counter, wfLapbPktStatsRejectTxs Counter, wfLapbPktStatsRestartTxs Counter, wfLapbPktStatsDiagTxs Counter, wfLapbPktStatsSegmentTxs Counter, wfLapbPktStatsBytesTxs Counter, wfLapbPktStatsIntBytesTxs Counter, wfLapbPktStatsDataRxs Counter, wfLapbPktStatsInterruptRxs Counter, wfLapbPktStatsResetRxs Counter, wfLapbPktStatsRrRxs Counter, wfLapbPktStatsRnrRxs Counter, wfLapbPktStatsRejectRxs Counter, wfLapbPktStatsRestartRxs Counter, wfLapbPktStatsDiagRxs Counter, wfLapbPktStatsSegmentRxs Counter, wfLapbPktStatsBytesRxs Counter, wfLapbPktStatsIntBytesRxs Counter, wfLapbPktStatsOnOffSwitch INTEGER } wfLapbPktStatsSlotNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Slot number and instance ID for this Lapb Packet Layer Line instance." ::= { wfLapbPktStatsEntry 1 } wfLapbPktStatsConnector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port number and instance ID for this Lapb Packet Layer Line instance." ::= { wfLapbPktStatsEntry 2 } wfLapbPktStatsLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the line number assigned to the driver X.25 is running over. No used in 7.60" ::= { wfLapbPktStatsEntry 3 } wfLapbPktStatsLLIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60." ::= { wfLapbPktStatsEntry 4 } wfLapbPktStatsCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Circuit number for this instance." ::= { wfLapbPktStatsEntry 5 } wfLapbPktStatsLineAddress OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The local X.121 address of this line." ::= { wfLapbPktStatsEntry 6 } wfLapbPktStatsMaxVcs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of Virtual Circuits allowed on this line." ::= { wfLapbPktStatsEntry 7 } wfLapbPktStatsActiveVcs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Active Virtual Circuits on this line." ::= { wfLapbPktStatsEntry 8 } wfLapbPktStatsActiveMax OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Highest number of active Virtual Circuits on this line." ::= { wfLapbPktStatsEntry 9 } wfLapbPktStatsTotalConnections OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Total Virtual Connections performed since start up." ::= { wfLapbPktStatsEntry 10 } wfLapbPktStatsFailedConnections OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of unsuccessful Virtual Connections performed since start up." ::= { wfLapbPktStatsEntry 11 } wfLapbPktStatsNormalDisconnects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Normal Virtual Circuit Disconnections." ::= { wfLapbPktStatsEntry 12 } wfLapbPktStatsAbnormalDisconnects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Abnormal Virtual Circuit Disconnections." ::= { wfLapbPktStatsEntry 13 } wfLapbPktStatsDataTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Packets Transmitted on this line." ::= { wfLapbPktStatsEntry 14 } wfLapbPktStatsInterruptTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Packets sent." ::= { wfLapbPktStatsEntry 15 } wfLapbPktStatsResetTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reset Requests sent." ::= { wfLapbPktStatsEntry 16 } wfLapbPktStatsRrTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Ready Packets sent." ::= { wfLapbPktStatsEntry 17 } wfLapbPktStatsRnrTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Not Ready Packets sent." ::= { wfLapbPktStatsEntry 18 } wfLapbPktStatsRejectTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reject Packets sent." ::= { wfLapbPktStatsEntry 19 } wfLapbPktStatsRestartTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Restart Packets sent." ::= { wfLapbPktStatsEntry 20 } wfLapbPktStatsDiagTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Diagnostic Packets sent." ::= { wfLapbPktStatsEntry 21 } wfLapbPktStatsSegmentTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Charge Units sent." ::= { wfLapbPktStatsEntry 22 } wfLapbPktStatsBytesTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Bytes sent." ::= { wfLapbPktStatsEntry 23 } wfLapbPktStatsIntBytesTxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Data Bytes sent." ::= { wfLapbPktStatsEntry 24 } wfLapbPktStatsDataRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Packets received on this line." ::= { wfLapbPktStatsEntry 25 } wfLapbPktStatsInterruptRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Packets received." ::= { wfLapbPktStatsEntry 26 } wfLapbPktStatsResetRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reset Requests received." ::= { wfLapbPktStatsEntry 27 } wfLapbPktStatsRrRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Ready Packets received." ::= { wfLapbPktStatsEntry 28 } wfLapbPktStatsRnrRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Receiver Not Ready Packets received." ::= { wfLapbPktStatsEntry 29 } wfLapbPktStatsRejectRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Reject Packets received." ::= { wfLapbPktStatsEntry 30 } wfLapbPktStatsRestartRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Restart Packets received." ::= { wfLapbPktStatsEntry 31 } wfLapbPktStatsDiagRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Diagnostic Packets received." ::= { wfLapbPktStatsEntry 32 } wfLapbPktStatsSegmentRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Charge Units received." ::= { wfLapbPktStatsEntry 33 } wfLapbPktStatsBytesRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data Bytes received." ::= { wfLapbPktStatsEntry 34 } wfLapbPktStatsIntBytesRxs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Interrupt Data Bytes received." ::= { wfLapbPktStatsEntry 35 } wfLapbPktStatsOnOffSwitch OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This tells the user if Statistics Computation is turned ON or OFF." ::= { wfLapbPktStatsEntry 36 } wfX25PvcServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF WfX25PvcServiceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "the table of Lapb Pvc Packet level parameters" ::= { wfX25Group 7 } wfX25PvcServiceEntry OBJECT-TYPE SYNTAX WfX25PvcServiceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the LAPB PKT table" INDEX { wfX25SlotNum, wfX25Connector, wfX25LineNumber, wfX25LLIndex, wfX25PvcServiceCct, wfX25PvcServiceIndex } ::= { wfX25PvcServiceTable 1 } WfX25PvcServiceEntry ::= SEQUENCE { wfX25PvcDelete INTEGER, wfX25PvcDisable INTEGER, wfX25SlotNum INTEGER, wfX25Connector INTEGER, wfX25LineNumber INTEGER, wfX25LLIndex INTEGER, wfX25PvcServiceCct INTEGER, wfX25PvcServiceIndex INTEGER, wfX25PvcServiceType INTEGER, wfX25PvcRxDefWindow INTEGER, wfX25PvcTxDefWindow INTEGER, wfX25PvcRxDefLength INTEGER, wfX25PvcTxDefLength INTEGER, wfX25PvcRxDefClass INTEGER, wfX25PvcTxDefClass INTEGER } wfX25PvcDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter, Default is created" DEFVAL { created } ::= { wfX25PvcServiceEntry 1 } wfX25PvcDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable Parameter" DEFVAL { enabled } ::= { wfX25PvcServiceEntry 2 } wfX25SlotNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Part of the Instance Identifier. This is the slot number where this X25 packet layer is running" ::= { wfX25PvcServiceEntry 3 } wfX25Connector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Part of the Instance Identifier. This is the physical connector number for the physical layer associated with this packet layer" ::= { wfX25PvcServiceEntry 4 } wfX25LineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Part of the Instance Id. This is the line number assigned to the LAPB driver associated with the X25 Packet layer." ::= { wfX25PvcServiceEntry 5 } wfX25LLIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance identifier. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60." ::= { wfX25PvcServiceEntry 6 } wfX25PvcServiceCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance Id. This is the Circuit number" ::= { wfX25PvcServiceEntry 7 } wfX25PvcServiceIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instace Id. This is the lcn on which this pvc is running" ::= { wfX25PvcServiceEntry 8 } wfX25PvcServiceType OBJECT-TYPE SYNTAX INTEGER { pdntype(1), ddntype(2), ptoptype(4), npttype(8), ipextype(16), qllctype(32) } ACCESS read-write STATUS mandatory DESCRIPTION "Type of Service for this PVC Service record" ::= { wfX25PvcServiceEntry 9 } wfX25PvcRxDefWindow OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "This is the receive window size used for setting up the pvc." DEFVAL { 2 } ::= { wfX25PvcServiceEntry 10 } wfX25PvcTxDefWindow OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "This is the transmit window size used for setting up the pvc." DEFVAL { 2 } ::= { wfX25PvcServiceEntry 11 } wfX25PvcRxDefLength OBJECT-TYPE SYNTAX INTEGER { size16(4), size32(5), size64(6), size128(7), size256(8), size512(9), size1024(10), size2048(11), size4096(12) } ACCESS read-write STATUS mandatory DESCRIPTION "This is the receive packet size." DEFVAL { size128 } ::= { wfX25PvcServiceEntry 12 } wfX25PvcTxDefLength OBJECT-TYPE SYNTAX INTEGER { size16(4), size32(5), size64(6), size128(7), size256(8), size512(9), size1024(10), size2048(11), size4096(12) } ACCESS read-write STATUS mandatory DESCRIPTION "This is the trasmit packet size" DEFVAL { size128 } ::= { wfX25PvcServiceEntry 13 } wfX25PvcRxDefClass OBJECT-TYPE SYNTAX INTEGER { thrclass75(3), thrclass150(4), thrclass300(5), thrclass600(6), thrclass1200(7), thrclass2400(8), thrclass4800(9), thrclass9600(10), thrclass19200(11), thrclass48k(12), thrclass64k(13) } ACCESS read-write STATUS mandatory DESCRIPTION "This is the receive througput class value that can be used on a per pvc basis. For this to be effective, the wfX25Throughput must be set ON" DEFVAL { thrclass19200 } ::= { wfX25PvcServiceEntry 14 } wfX25PvcTxDefClass OBJECT-TYPE SYNTAX INTEGER { thrclass75(3), thrclass150(4), thrclass300(5), thrclass600(6), thrclass1200(7), thrclass2400(8), thrclass4800(9), thrclass9600(10), thrclass19200(11), thrclass48k(12), thrclass64k(13) } ACCESS read-write STATUS mandatory DESCRIPTION "This is the transmit througput class value that can be used on a per pvc basis. For this to be effective, the wfX25Throughput must be set ON" DEFVAL { thrclass19200 } ::= { wfX25PvcServiceEntry 15 } wfX25QllcAddrMapTable OBJECT-TYPE SYNTAX SEQUENCE OF WfX25QllcAddrMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "table of X.121 address to LLC Mac address mappings." ::= { wfX25Group 8 } wfX25QllcAddrMapEntry OBJECT-TYPE SYNTAX WfX25QllcAddrMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the QLLC Address Mapping table" INDEX { wfX25QllcAddrMapCct, wfX25QllcAddrMapIndex } ::= { wfX25QllcAddrMapTable 1 } WfX25QllcAddrMapEntry ::= SEQUENCE { wfX25QllcAddrMapDelete INTEGER, wfX25QllcAddrMapDisable INTEGER, wfX25QllcAddrMapState INTEGER, wfX25QllcAddrMapCct INTEGER, wfX25QllcAddrMapIndex INTEGER, wfX25QllcAddrMapPartnerX121 DisplayString, wfX25QllcAddrMapAdjacentX121 DisplayString, wfX25QllcAddrMapPid INTEGER, wfX25QllcAddrMapPartnerMac OCTET STRING, wfX25QllcAddrMapPartnerSap INTEGER, wfX25QllcAddrMapAdjacentMac OCTET STRING, wfX25QllcAddrMapAdjacentSap INTEGER, wfX25QllcAddrMapOptions INTEGER, wfX25QllcAddrMapTrace INTEGER, wfX25QllcAddrMapPuType INTEGER, wfX25QllcAddrMapGenXid INTEGER, wfX25QllcAddrMapNodeId OCTET STRING, wfX25QllcAddrMapName DisplayString } wfX25QllcAddrMapDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter." DEFVAL { created } ::= { wfX25QllcAddrMapEntry 1 } wfX25QllcAddrMapDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter." DEFVAL { enabled } ::= { wfX25QllcAddrMapEntry 2 } wfX25QllcAddrMapState OBJECT-TYPE SYNTAX INTEGER { active(1), notactive(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the QLLC Mapping." DEFVAL { notpresent } ::= { wfX25QllcAddrMapEntry 3 } wfX25QllcAddrMapCct OBJECT-TYPE SYNTAX INTEGER(1..1024) ACCESS read-only STATUS mandatory DESCRIPTION "Circuit number and instance ID member." ::= { wfX25QllcAddrMapEntry 4 } wfX25QllcAddrMapIndex OBJECT-TYPE SYNTAX INTEGER(1..4000) ACCESS read-only STATUS mandatory DESCRIPTION "X.25 QLLC Address Map entry record ID for this instance." ::= { wfX25QllcAddrMapEntry 5 } wfX25QllcAddrMapPartnerX121 OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The X.121 address of a X.25 device emulated by this interface." ::= { wfX25QllcAddrMapEntry 6 } wfX25QllcAddrMapAdjacentX121 OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "The X.121 address of a X.25 device connecting thru this interface. This address may contain wildcard characters." ::= { wfX25QllcAddrMapEntry 7 } wfX25QllcAddrMapPid OBJECT-TYPE SYNTAX INTEGER(1..254) ACCESS read-write STATUS mandatory DESCRIPTION "QLLC Protocol ID used in the first byte of Call User Data of the X.25 Call Request packet." DEFVAL { 195 } ::= { wfX25QllcAddrMapEntry 8 } wfX25QllcAddrMapPartnerMac OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The LLC MAC address of a LLC device connecting thru this interface. The LLC MAC address may contain wildcard characters, see wfX25QllcAddrMapOptions attribute below." ::= { wfX25QllcAddrMapEntry 9 } wfX25QllcAddrMapPartnerSap OBJECT-TYPE SYNTAX INTEGER(1..254) ACCESS read-write STATUS mandatory DESCRIPTION "The SAP of a LLC device connecting thru this interface." DEFVAL { 4 } ::= { wfX25QllcAddrMapEntry 10 } wfX25QllcAddrMapAdjacentMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-write STATUS mandatory DESCRIPTION "The LLC MAC address of a LLC device emulated by this interface. If set to nil, a LLC MAC address will be dynamically assign by X.25 from an address pool defined in the X.25 Service Record." ::= { wfX25QllcAddrMapEntry 11 } wfX25QllcAddrMapAdjacentSap OBJECT-TYPE SYNTAX INTEGER (1..254) ACCESS read-write STATUS mandatory DESCRIPTION "The SAP of a LLC device emulated by this interface." DEFVAL { 4 } ::= { wfX25QllcAddrMapEntry 12 } wfX25QllcAddrMapOptions OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object is a bitmask, setting individual bit postions enable the option. Values may be added together to enable multiple options. Hex Dec Value Value Options --------------------------------------------------------- 0x0001 1 Do not wait for Adjacent DTE/DCE to send an QXID before forwarding an QXID to it. 0x0002 2 Enable when SDLC endstations are connecting to QLLC hosts that do not support receipt of XID polls and do not retransmit XIDs. 0x0004 4 wfX25QllcAddrMapPartnerMac field contains wildcard characters." DEFVAL { 0 } ::= { wfX25QllcAddrMapEntry 13 } wfX25QllcAddrMapTrace OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object is a bitmask, setting individual bit postions enable logging of internal QLLC messages and events. Values may be added together to enable multiple message groups. Hex Dec Value Value Message/Event --------------------------------------------------------- 0x0001 1 Enable QLLC logging. 0x0002 2 Data frames/packets. 0x0004 4 Flow Control messages. 0x0008 8 Client registration messages. 0x0010 16 X.25 session establishment messages. 0x0020 32 Test frames/packets. 0x0040 64 XID frames/packes. 0x0080 128 Set Mode frames/packets. 0x0100 256 Disconnect frames/packets. 0x0200 512 Configuration changes. 0x0400 1024 Death of client (DLSw or APPN). 0x0800 2048 Data Path (DP) messages." DEFVAL { 0 } ::= { wfX25QllcAddrMapEntry 14 } wfX25QllcAddrMapPuType OBJECT-TYPE SYNTAX INTEGER { pu21(1), pu20(2) } ACCESS read-write STATUS obsolete DESCRIPTION "PU type (T2.0 or T2.1) of the locally attached QLLC device." DEFVAL { pu20 } ::= { wfX25QllcAddrMapEntry 15 } wfX25QllcAddrMapGenXid OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Simulate receiving an XID command from the QLLC device. This object should be enabled when an PU 2.0 QLLC device is connecting thru DLSw to an non-X.25 host." DEFVAL { disabled } ::= { wfX25QllcAddrMapEntry 16 } wfX25QllcAddrMapNodeId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-write STATUS obsolete DESCRIPTION "The 8 hexadecimal digit Node Identification field of the simulated XID (see wfX25QllcAddrMapGenXid object). This field has two sub-fields, ID Block and ID Number. The first 3 hexadecimal digits are the ID block value and the last 5 hexadecimal digits are the ID Number value." ::= { wfX25QllcAddrMapEntry 17 } wfX25QllcAddrMapName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "A informational name for this QLLC Mapping." ::= { wfX25QllcAddrMapEntry 18 } END -- Wellfleet-X25-MIB